Professional Documents
Culture Documents
Eddy Current Testing Level 2 Questions
Eddy Current Testing Level 2 Questions
1. A method of minimizing the effect of indications caused by gradual dimensional changes while
retaining the indication caused by discontinuities is to/ Một phương pháp làm giảm thiểu ảnh hưởng
của các chỉ thị gây ra bởi sự thay đổi kích thước trong khi vẫn giữ lại chỉ thị gây ra bởi các bất liên
tục là để:
a. Enable a high-pass filter in the eddy current test equipment/ Kích hoạt chức năng lọc cao qua
trong máy kiểm tra dòng xoáy.
b. Enable a low-pass filter in the eddy current test equipment/ Kích hoạt chức năng thấp qua trong
máy kiểm tra dòng xoáy.
c. Increase the bandpass of the amplifier/ Tăng (tần số trung bình) băng thông của bộ khuếch đại.
d. Use the impedance method of testing / Sử dụng phương pháp kiểm tra tổng trở.
2. Which of following method may not be used to improve the signal-to-noise ratio of an electro-
magnetic testing system? / Phương pháp nào sau đây có thể không sử dụng để tang cường ty số tín
hiệu trên nhiễu của 1 hệ thống kiểm tra điện từ?
3. In order to decrease the effect on conductivity readings due to variations in test part thickness/ Để
giảm sự ảnh hưởng của giá trị độ dẫn điện do sự thay đổi độ dày vật kiểm tra:
a. The test frequency should be increased/ nên tăng tần số kiểm tra
b. The test frequency should be decrease/ nên giảm tần số kiểm tra
c. The fill factor should be decrease/ nên giảm hệ số điền đầy
d. There is no practical method for decreasing this effect/ không có phương pháp thực hành nào để
giảm hiệu ứng này.
4. When testing by the eddy current technique, discontinuities will be most easily detected when the
eddy current are/ Khi kiểm tra bằng kỹ thuật dòng xoáy, bất liên tục dễ ghi nhận nhất khi dòng xoáy
là:
5. A term used to describe the effect observed due to a change in the electromagnetic coupling
between a test specimen and a probe coil when the distance of separation between them is varied is:
30. In Figure 3, the solid curves are plots for different values of: / Trong hình 3, các đường cong đậm
thể hiện giá trị của:
a. Fill factor – Thừa số nâng
b. Heat treatment – Xử lý nhiệt
c. Conductivity – Độ dẫn điện
d. Permeability – Độ từ thẩm
23
31. Which of the following would be easier to detect in tubing by the eddy current technique using the
self-comparision differential coil arrangement? / Điều nào sau đây sẽ dễ hơn để ghi nhận trong kiểm
tra ống bằng dòng xoáy sử dụng cuộn dây vi sai tự so sánh?
a. Gradual change in diameter – Sự thay đổi chậm về đường kính
b. Gradual changes in conductivity – Sự thay đổi chậm về độ dẫn điện
c. Changes in temperature – Sự thay đổi về nhiệt độ
d. Short discontinuities – Các bất liên tục ngắn
32. The inductive reactance of a coil is measured in units of: / Đơn vị cảm kháng của cuộn dây là:
a. Mhos
b. Ohms
c. Henries
d. Gauss
33. To eliminate any dependence on the number of test coil turns, the inductance values of an
impedance diagram are: / Để loại bỏ mọi sự phụ thuộc lên số vòng dây trong cuộn dây kiểm tra, các
giá trị tự cảm của giản đồ tổng trở:
a. Disregarded – Không cần quan tâm
b. Normalized – Chuẩn hóa
c. Corrected to a value of one (1) – lấy giá trị bằng 1.
d. Corrected to a value less than one (1). – lấy giá trị nhỏ hơn 1.
34. A term used to definie a system that indicates only the magnitude of variations in the total coil
impedance regardless of the phase or direction in which it occurs on an impedance plane is: / Khái
niệm được sử dụng để định nghĩa 1 hệ thống mà thể hiện duy nhất độ lớn tổng cộng sự thay đổi về
tổng trở bất kể sự thay đổi về pha và hướng trên giản đồ tổng trở là:
a. Inductive reactance magnitude system – Hệ thống chỉ thị cảm kháng
b. Feedback-controlled system – Hệ thống phản hồi có kiểm soát
c. Impedance-magnitude system – Hệ thống độ lớn tổng trở
d. Impedance vector analysis system – Hệ thống phân tích vector tổng trở
24
35. When performing eddy current testing on tubing with a system that includes adjustable filter
functions, which of the following variables would be classified as high-frequency variable? / Khi
kiểm tra dòng xoáy với ống bằng hệ thống bao gồm bộ lọc điều chỉnh được, tham số nào sau đây
được phân loại là tần số cao
a. Small discontinuities – bất liên tục nhỏ
b. Conductivity changes – thay đổi độ dẫn điện
c. Diameter changes – thay đổi đường kính
d. Wall thickness variations – thay đổi độ dày
36. A major problem for an untrained or inexperienced operator using the eddy current test method is
the: / Vấn đề chủ yếu của nhân viên không được đào tạo hay thiếu kinh nghiệm sử dụng phương
pháp kiểm tra dòng xoáy là:
a. Inability of eddy current testing to accurately measure conductivity – Không có khả năng kiểm
tra chính xác độ dẫn điện bằng ET.
b. Large number of varialbes that appear in the output readout mechanism – Quá nhiều tín hiệu
xuất hiện trên màn hình.
c. Need to test at low speeds to prevent skipping – Cần phải kiểm tra ở tốc độ chậm để ngăn ngừa
sự bỏ sót chỉ thị.
d. Inability of eddy current testing to detect small discontinuities – Không có khả năng phát hiện
bất liên tục nhỏ.
37. Figure 4 illustrates the fact that the limit frequency (fg) equations and the impedance diagrams for
long solid rods and long thin-walled tubing are: / Hình 4 thể hiện phương trình về tần số giới hạn và
giản đồ tổng trở cho thanh đặc dài và ống mỏng dài là:
a. Different – khác nhau
b. Identical – phân biệt được
c. Similar – tương tự
d. Linearly related – liên quan đến nhau.
25
38. When a direct current saturation technique is appied to a ferromagnetic material, the fux density in
the material is: / Khi kỹ thuật bão hòa dòng 1 chiều được áp dụng với vật liệu sắt từ, mật độ từ
thông trong vật liệu là:
a. Less than the flux density generated by the test coil because of heat losses – Nhỏ hơn mật độ từ
thông tạo bởi cuộn dây do sinh nhiệt
b. Less than theflux density generated by the test coil because of resistivity - Nhỏ hơn mật độ từ
thông tạo bởi cuộn dây do điện trở
c. The same as the flux density generated by the test coil – Tương tự như tạo bởi cuộn dây
d. Greater than the flux denisty generated by the test coil – lớn hơn
39. In eddy current testing, the specimen is coupled to the test coil by:/ Trong kiểm tra dòng xoáy, cuộn
dây và vật kiểm kết nối với nhau bằng:
a. Core coupling – Lõi sắt
b. Magnetic saturation – Từ trường bão hòa
c. The coil’s magnetic field – Từ trường của cuộn dây
d. Magnetic domains – các miền từ
40. The thickness fo nonconductive coatings on a conductive base can be most simply measured by: /
Độ dày lớp phủ không dẫn điện trên vật dẫn điện có thể đo một cách đơn giản bằng cách:
a. Observing the liftoff effect caused by the coating – Quan sát hiệu ứng liftoff gây ra bởi lớp phủ
b. Testing both sides of the specimen – Kiểm tra cả 2 mặt của mẫu
c. Raying the current in test coil -
d. Varying the test frequency over a given range during the test – thay đổi tần số theo dải cho trước
trong quá trình kiểm tra.
26
41. The use of magnetic shielding around the exciting coil will generally: / Sử dụng che chắn từ trường
quanh cuộn dây phát nhìn chung sẽ:
a. Increase the magnetic field extension but decrease the eddy current penetration – Tăng sự mở
rộng từ trường nhưng giảm độ xuyên thấu dòng xoáy
b. Increased he magnetic field extension and eddy current penetration – tăng cường sự mở rộng từ
trường và độ xuyên thấu dòng xoáy
c. Decrease the magnetic field extension but incrase the eddy current penetration – Giảm sự mở
rộng từ trường nhưng tăng độ xuyên thấu
d. Decrease the magnetic field extension and eddy current penetration – Giảm cả sự mở rộng từ
trường và sự xuyên thấu.
42. Which of the following is not a factor that affects the inductance of an eddy current test coil? / Điều
nào sau đây không phải là 1 tham số ảnh hưởng đến độ tự cảm của cuộn dây kiểm tra dòng xoáy?
a. Diameter of the coils – Đường kính cuộn dây
b. Test frequency – Tần số kiểm tra
c. Overall shape of the coils – Hình dạng chung của cuộn dây
d. Distance from other coils – Khoảng cách đến cuộn dây khác
43. The formula used to calculate the impedance of an eddy current test coil is: / Công thức để tính tổng
trở của cuộn dây là:
a. Z = 2π.f.L
b. Z = XL + R
c. Z = sqrt(XL + R)
d. Z = sqrt(XL2 + R2)
44. An out-of-phase condition between current and voltage: / Một điều kiện ngược pha của dòng và thế
là:
a. Can exist only in the primary winding of an edy current coil – Có thể chỉ tồn tại trong cuộn sơ
cấp của đầu dò
b. Can exist only in the secondary windings of an eddy current coil – Có thể chỉ tồn tại trong cuộn
thứ cấp của đầu dò
c. Can exist in both the primary and secondary windings of an eddy current probe – Có thể tồn tại
trong cả 2 cuộn sơ cấp và thứ cấp.
d. Exists only in the test specimen – Tồn tại chỉ trong vật kiểm
45. A surface coil mounted so that the coil can be rotated about the circumference of a test specimen is
known as a(n): / Cuộn dây mặt lắp đặt sao cho có thể quay xung quanh chu vi của vật được gọi:
a. Bobbin coil – Cuộn dây trong
b. Encircling coil – cuộn dây ngoài
c. Rotating coil – Cuộn dây xoay
d. Gap coil – Cuộn dây ghép sát
46. An eddy current test coil which uses high permeability material to purposely shape the magnetic
field is known as a(n): / Một đầu dò ET mà sử dụng vật liệu có độ từ thẩm cao để định hình từ
trường được gọi là:
a. Bobbin coil – Đầu dò trong
b. Encircling coil – Đầu dò ngoài
c. Ratating coil – Đầu dò xoay
d. Shielded coil – Đầu dò định hướng (che chắn từ trường)
47. The conductivity value for a metal would most likely be influenced by which of the following
factors? / Giá trị độ dẫn điện của một kim loại hầu như bị ảnh hưởng bởi tham số nào sau đây?
a. Test frequency – tần số
b. Cold working performed on the metal – Khi gia công nguội được thực hiện trên kim loại
c. Magnetic filed – Từ trường
d. Induced current – Dòng cảm ứng
48. Which of the following materials would more likely be used to create a holding fixture for a probe
coil? / Vật liệu nào sau đây thường được sử dụng để tạo khung đầu dò?
27
a. Aluminum - Nhôm
b. Plastic – Nhựa
c. Copper – Đồng
d. Steel - Thép
49. A term used to define the timing relationships involved in alternating current signals is: - Khái niệm
được sử dụng để định nghĩa mối liên hệ về thời gian trong tín hiệu dòng xoay chiều là:
a. Magnitude – Độ lớn
b. Phase - Pha
c. Impedance – tổng trở
d. Reactance - kháng
50. Nonferromagnetic tubing is usally tested with multifrequency eddy current techniques in the
differential and absolute modes using a(n): / Ống phi từ tính thường được kiểm tra bằng dòng xoáy
đa tần số ở dạng vi sai và tuyệt đối, sử dụng một:
a. Through-transmission mode – Chế độ truyền qua
b. Encircling coil – Cuộn dây ngoài
c. Surface coil – Cuộn dây mặt
d. Bobbin coil – Cuộn dây trong
51. Which of the followng coil arrangements would eliminate or decrease the effects of minor
variations in diameter, chemical composition, hardness, etc., which occur gradually along the length
of a wire? / Cách sắp xếp cuộn dây nào sau đây sẽ loại bỏ hoặc giảm ảnh hưởng của những thay đổi
nhỏ về đường kính, thành phần hóa học, độ cứng, vv…, mà xảy ra chậm dọc theo chiều dài của sợi
dây?
a. Self-comparison differential – Vi sai tự so sánh
b. External reference absolute – Tuyệt đối so sánh ngoài
c. Single coil absolute – Tuyệt đối 1 cuộn dây
d. Double coil absolute – Tuyệt đối 2 cuộn dây
52. Which of the following conditions are not valid criteria when selecting speciments to be used as
reference standards? – Điều kiện nào sau đây không phải là 1 tiêu chí ý nghĩa khi lựa chọn mẫu để
làm chuẩn đối chứng?
a. The specimen should be of the same size and shape as the piece to be tested – Cùng hình dạng
và kích thước với vật đang kiểm tra
b. The specimen should have the same heat treatment as the piece to be tested – Cùng chế độ xử lý
nhiệt với vật đang kiểm tra
c. The surface finish of the specimen should be the same as the piece to be tested – Cùng điều kiện
bề mặt với vật kiểm tra
d. If the materal is aluminum, the surface should always be nodized – Nếu là vật liệu nhôm, bề mặt
luôn phải được a-nốt hóa.
53. An eddy current test coil’s magnetic field intensity in air: / Cường độ từ trường của cuộn dây dòng
xoáy trong không khí:
a. Increases with distance outside the coil and varies across the diameter inside the coil – Tăng khi
ra xa cuộn dây và thay đổi theo tiết diện cuộn dây
b. Decrease with distance outside the coil and varies across the diameter inside the coil – Giảm khi
tăng khoảng cách so với cuộn dây và thay đổi theo tiết diện cuộn dây.
c. Decrease with distance outside the coil and is assumed to be constant across the diameter inside
the coil – Giảm khi tăng khoảng cách so với cuộn dây và được coi là không đổi theo tiết diện
cuộn dây.
d. Increases with distance outside the coil and is assumed to be constant across the diameter inside
the coil – Tăng khi tăng khoảng cách từ cuộn dây và được coi là không đổi theo tiết diện cuộn
dây.
54. The circuitry or electronic functions that make its possible to minimize the effect of signals caused
by variables of no interest on the readout mechanism are based on differences in: / Tác dụng mạch
28
hay điện mà làm nó có thể giảm thiểu ảnh hưởng của tín hiệu gây ra bởi sự thay đổi của các thông
tin không quan tâm dựa trên sự khác nhau về:
a. Amplitude – Biên độ
b. Phase – Pha
c. Frequency – Tần số
d. Any one or a combination of the quantities listed above – bất kỳ 1 hoặc kết hợp nhiều yếu tố
trên.
55. When a nonferromagnetic rod is placed inside an encircling coil – Khi thanh phi từ tính đặt trong
cuộn dây ngoài:
a. The magnetic field generated by the coil is increased in intensity – Từ trường tạo ra bởi cuộn
dây tăng về cường độ
b. The distribution of eddy currents is uniform through the rod’s cross section – Sự phân bố dòng
xoáy là đồng nhất trên toàn tiết diện cuộn dây.
c. The distribution of eddy currents is at a maximum at the rod’s surface, or near the surface, and
decrease to essentially zero at the rod’s center – Sự phân bổ dòng xoáy cực đại trên mặt thanh
hoặc gần bề mặt, và giảm về 0 tại tâm.
d. The temperature of the rod decreases – Nhiệt độ thanh giảm.
56. A decrease in conductivity is equipvalent to: / Giảm độ dẫn điện tương đương với:
a. An increase in permeability – Tăng độ từ thẩm
b. An increase in resitivity – Tăng điển trở
c. A decrease in permeability – Giảm độ từ thẩm
d. A decrease in resistivity – Giảm điển trở
57. When the voltage applied to a circuit and the current through the circuit both reach their maximums
and minimums at the same time, the voltage and current are: / Khi điện thế áp vào mạch và dòng
điện qua mạch cùng đạt đến cực đại và cực tiểu cùng lúc thì chúng:
a. Additive – Bổ sung nhau
b. In phase – Cùng pha
c. Regenerative – Tái sinh
d. Out of phase - Ngược pha
58. Which of the following is not a commonly used eddy current testing readout mechanism? / Điều
nào sau đây không thường được sử dụng trong hiển thị kiểm tra dòng xoáy?
a. Signal generator – Bộ tạo tín hiệu
b. Meter – Máy đo
c. X-Y display – Hiển thị tọa độ X-Y
d. Strip-chart recorder – Bộ ghi dải
59. Which of the following materials would have the highest resistivity value? / Vật liệu nào sau đây có
điện trở suất cao nhất
a. Aluminum with a 42% IACS rating – Nhôm 42% IACS
b. Magnesium with a 37% IACS rating – Ma nhê 37% IACS
c. Cast steel ith a 10.7% IACS rating - Thép 10,7% IACS
d. Zirconium with a 3.4% IACS rating – Zirconium 3,4% IACS
60. The magnetic field generated by eddy currents induced in a test specimen: / Từ trường tạo ra bởi
dòng xoáy cảm ứng trong vật:
a. Opposes the magnetic field that induced the eddy currents – Ngược với từ trường mà cảm ứng
dòng xoáy.
b. Reinforces the magnetic field that indued the eddy currents – Tăng cường từ trường cảm ứng
dòng xoáy.
c. Cancels the magnetic filed that induced the eddy currents – Khử từ trường cảm ứng dòng xoáy
d. Has ho effect on the magnetic filed that induced the eddy currents – Không ảnh hưởng lên từ
trường cảm ứng dòng xoáy.
61. The impedance of a test coil usually can be represented by the vector sum of – Tổng trở của cuộn
dây thường được biểu diễn bởi vector tổng của:
29
a. Inductive reactance and resistance – Cảm kháng và điện trở
b. Capacitive reactance and resistance – Dung kháng và điện trở
c. Inductive reactance and capacitive reactance. – Cảm kháng và dung kháng
d. Inductance and capacitance. – Tự cảm và điện dung
62. For age hardenable aluminum and titanium alloys, changes in hardness are indicated by changes in /
Với hợp kim nhôm và Titan già hóa được, sự thay đổi độ cứng chỉ ra bởi sự thay đổi của:
a. Retentivity – Độ giữ từ
b. Permeability – Độ từ thẩm
c. Conductivity – Độ dẫn điện
d. Magnetostriction – Sự từ dảo
63. Te penetration of eddy currents in a conductive material is decreased when: / Độ xuyên thấu của
dòng xoáy trong vật dẫn điện giảm khi:
a. Test frequency or conductivity of the specimen is decreased – Tần số hoặc độ dẫn điện của vật
giảm.
b. Test frequency is dereased or condutivitity of the specimen is increased – Tần số giảm hoặc độ
dẫn điện của vật tăng
c. Test frequency, conductivity of the specimen, or permeability of the specimen is increased –
Tần số, độ dẫn điện hoặc độ từ thẩm của vật tăng.
d. Permeability of the specimen is decreased – Độ từ thẩm của vật giảm.
64. When the alternating current in an eddy current coil reverses direction: / Khi dòng điện xoay chiều
trong cuộn dây đảo chiều:
a. The direction of the eddy currents in a part remains the same – Hướng của dòng điện xoáy trong
vật giữ nguyên không đổi.
b. The eddy currents in the test part will chang phased by 45o – Dòng xoáy trong vật sẽ đổi pha 45
độ.
c. The direction of the eddy curetns in the part also reverses – Hướng của dòng xoáy cũng đổi.
d. The eddy currents in the part remain the same – Dòng xoáy trong vật giữ nguyên.
65. The limit frequency (fg) is calculated based on all of the following test-object parameters except /
Tần số giới hạn (fg) được tính dựa trên tất cả các tham số về vật kiểm tra sau đây, ngoại trừ:
a. Metal hardness – Độ cứng
b. Permeability – Độ từ thẩm
c. Conductivity – Độ dẫn điện
d. Diameter of the test object – Đường kính của vật.
66. When a rod is placed in an encircling type of coil, the density of eddy currents will be the greatest: /
Khi thanh tròn được đặc trong cuộn dây ngoài, mật độ dòng xoáy sẽ lớn nhất:
a. At the surface – Tại bề mặt
b. At the center – Tại tâm
c. Midway between the surface and the center – Giữa bề mặt và tâm
d. At the applicable depth of penetration. – Tại độ sâu xuyên thấu đang áp dụng.
67. The term fill factor applies to: / Hệ số điền đầy áp dụng cho:
a. a surface coil – Cuộn dây mặt
b. coaxial cable – Cáp đồng trục
c. an encircling coil – Cuộn dây ngoài
d. a pencil probe – Đầu dò bút chì
68. An eddy current system using handling equipment with automatic marking of the defective areas
primarily makes it possible to:/ Hệ thống dòng xoáy sử dụng thiết bị cầm tay với khả năng tự động
đánh dấu vùng khuyết tật chủ yếu có thể:
a. Remove defective areas of the product, if desired – Loại bỏ vùng có khuyết tật khi cần.
b. Eliminate test surface contamination – Loại bỏ sự nhiễm bẩn bề mặt
c. Allow an inexperiencd operator to establish the discontinuity cause – Cho phép kỹ thuật viên
thiếu kinh nghiệm xác định nguyên nhân khuyết tật.
d. Pass rejectable material – Cho chấp nhận các vật liệu bị hỏng.
30
69. Two test coils are often used in a brigde circuit to: / Hai cuộn dây thường được sử dụng trong mạch
cầu để:
a. Eliminate skin effect – Loại bỏ hiệu ứng lớp da
b. Determin the differences between a known standard sample and a test piece – Xác định sự khác
nhau giữa mẫu chuẩn đã biết với mẫu kiểm tra.
c. Increase the conducitivity of the circuit – Tăng độ dẫn điện của mạch
d. Decrease the system sensitivity – Giảm độ nhạy hệ thống.
70. The actual frequencies used in any specific eddy current inspection should be selected on the bases
of any of the following except: / Tần số thực tế sử dụng trong kiểm tra dòng xoáy cụ thể nên được
chọn dựa trên các điều sau, ngoại trừ:
a. Thickness of the material – Độ dày vật liệu
b. Desired depth of penetration – Độ xuyên sâu mong muốn
c. Degree of sensitivity or resolution requied – Độ nhạy và độ phân giải yêu cầu
d. To decrease rejection rates based on required production levels – Để giảm mức độ reject dựa
trên mức chất lượng yêu cầu.
71. The term used to define the difference between actual instrument output and expected output as
defined by a traight line calibration curve is: / Khái niệm sử dụng để định nghĩa sự khác nhau giữa
tín hiệu của thiết bị và tín hiệu mong muốn như đã xác định bởi một đường cong hiệu chuẩn là:
a. Phase shift – Dịch pha
b. Nonlinearity – Không tuyến tính
c. Liftoff – hệ số nâng
d. Skin effect – Hiệu ứng lớp da
72. A term used to define any change in a sinusoidal signal when the output is not a linear reproduction
of the input is: / Khái niệm được sử dụng để định nghĩa bất kỳ sự thay đổi nào về tín hiệu hình sin
khi tín hiệu đầu ra không tái hiện tuyến tính tín hiệu đầu vào là:
a. Distortion – Méo
b. Linearity – Tuyến tính
c. Phased shifting – dịch pha
d. Dynamic range – Dải rộng
73. The magnetic domains in an unmagnetized ferromagnetic material: / Miền từ trong vật liệu sắt từ
chưa bị từ hóa:
a. Are arranged to facilitate the conduction of electrons – Được sắp xếp để thực hiện việc dẫn điện
tử.
b. Are randomly oriented and neutralize each other – Định hướng ngẫu nhiên và trung hòa nhau
c. Are uniformly oriented – Định hướng đồng nhất
d. Create a major north and south pole in the material – Tạo ra một cực Nam – Bắc trong vật liệu.
74. When a magnetic material is palecd in a region of an applied magnetizing force, a magnetic field is
developed in the material by means of: / Khi vật liệu từ tính đặt trong vùng có lực từ hóa, từ trường
hình thành trong vật bằng cách:
a. Induction – Cảm ứng
b. Conduction – Dẫn điện
c. Heat transfer – Truyền nhiệt
d. Magnetic domain transfer – Truyền miền từ
75. The atoms of a metal showing magnetic characteristics are grouped into regions that are the smallest
know permanet magnets. These regions are called: / Các nguyên tử của kim loại cho thấy đặc trưng
từ được nhóm thành từng vùng giống như những nam châm vĩnh cửa cực nhỏ. Các vùng này gọi là:
a. Lattice structures – Cấu trúc tinh thể
b. Cells – Tế bào
c. Domains – Miền từ
d. Planetary spins – hành tinh quay
76. The flux density in a magnetized material is usually designated by the – Mật độ từ thông trong vật
liệu đã từ hóa thường được biểu thị bằng ký hiệu:
31
a. Symbol m
b. Symbol s
c. Letter B
d. Letter H
77. The magnetizing force of a saturation coil is usually designated by the: / Lực từ hóa của cuộn dây
bão hòa được biểu thị bằng ký hiệu:
a. Symbol m
b. Symbol s
c. Letter B
d. Letter H
78. The ratio of a material’s flux density to the applied magnetizing force can be used to determine the
material’s: / Tỷ số mật độ từ thông trên lực từ hóa được dùng để xác định giá trị:
a. Permeability – Độ từ thẩm
b. Conductivity – Độ dẫn điện
c. Resistivity – Điện trở suất
d. Liftoff – Hệ số nâng
79. The two sine wave signals (V and I) shown in Figure 5 are: / Hai tín hiệu hình sine (V và I) chỉ ra
trên hình 5 là:
a. In phase - Cùng pha
b. 45o out of phased - lệch pha 45 độ
c. 90o out of phased – Lệch pha 90 độ
d. 180o out of phased – Lệch pha 180độ
80. The two sine wave signals (V and I) shown in Figure 6 are: / Hai tín hiệu hình sine (V và I) chỉ ra
trên hình 6 là:
a. In phase – Cùng pha
b. 45o out of phased – Lệch pha 45 độ
c. 90o out of phased – Lệch pha 90 độ
d. 180o out of phased – Lệch pha 180 độ
32
81. The symbol commonly used to signify impedance is: / Ký hiệu chỉ tổng trở là:
a. Z
b. XL
c. R
d. XC
82. In Figure 7, H represents: / Trong hình 7, H thể hiện:
a. The magnetizing force – Lực từ hóa
b. The material’s flux density – Mật độ từ thông
c. The material’s permeability – Độ từ thẩm
d. The maerial’s conductivity – Độ dẫn điện
34
ET LEVEL II ANSWERES / ĐÁP ÁN DÒNG XOÁY BẬC II
1 A 45 C
2 D 46 D
3 A 47 B
4 B 48 B
5 D 49 B
6 A 50 D
7 D 51 A
8 A 52 D
9 C 53 B
10 C 54 B
11 B 55 C
12 A 56 B
13 C 57 B
14 B 58 A
15 A 59 D
16 B 60 A
17 B 61 A
18 C 62 C
19 D 63 C
20 B 64 C
21 B 65 A
22 A 66 A
23 C 67 C
24 D 68 A
25 B 69 B
26 C 70 D
27 B 71 B
28 C 72 A
29 C 73 B
30 A 74 A
31 D 75 C
32 B 76 C
33 B 77 D
34 C 78 A
35 A 79 A
36 B 80 C
37 A 81 A
38 D 82 A
39 C 83 B
40 A 84 C
41 D 85 D
42 B 86 D
43 D
44 C
35