Professional Documents
Culture Documents
Exterior Trim Location Index: Ac5uuw00006865
Exterior Trim Location Index: Ac5uuw00006865
id091600800100
id091600800100
ac5uuw00006865
Cowl grille
2
(See COWL GRILLE REMOVAL/INSTALLATION.)
Sail garnish
3
(See SAIL GARNISH REMOVAL/INSTALLATION.)
Rear mudguard
10
(See MUDGUARD REMOVAL/INSTALLATION.)
Deflector
11
(See DEFLECTOR REMOVAL/INSTALLATION.)
Front mudguard
14
(See MUDGUARD REMOVAL/INSTALLATION.)
Liftgate garnish
16
(See LIFTGATE GARNISH REMOVAL/INSTALLATION.)
Rear spoiler
17
(See REAR SPOILER REMOVAL/INSTALLATION.)
Roof molding
(See ROOF MOLDING REMOVAL.)
18
(See ROOF MOLDING INSTALLATION.)
Extractor chamber
20
(See EXTRACTOR CHAMBER REMOVAL/INSTALLATION.)
Ornament
22
(See ORNAMENT INSTALLATION.)
ac5uuw00008352
id091600808400
ac5uuw00008360
ac5uuw00009430
3.Pull the rear over fender in the direction of the arrow shown in the figure and disengage the clips shown
in the figure.
ac5uuw00008362
6.Detach the tabs from the rear bumper and remove the rear splash shield.
id091600801800
1.Remove the front over fender lower. (See FRONT OVER FENDER REMOVAL/INSTALLATION.)
ac5uuw00005167
4.Move the side step molding in the direction of the arrow shown in the figure and remove it.
ac5uuw00005169
id091600815000
2.Remove the liftgate upper trim. (See LIFTGATE UPPER TRIM REMOVAL/INSTALLATION.)
ac5uuw00007268
id091600400000
Front
1.Pull the side garnish in the direction of the arrow shown in the figure and remove it.
ac5uuw00007244
Rear
1.Pull the side garnish in the direction of the arrow shown in the figure and remove it.
id091600451200
ac5uuw00007233
3.Insert a tape-wrapped flathead screwdriver into the shown in the figure and remove clip A in the
direction of arrow (1).
4.Pull the sail garnish in the direction of arrow (2) and remove it while detaching clips B.
id091600447800
ac5uuw00007252
2.Move the remover tool in the direction of the arrows shown in the figure and detach the roof molding
from the front T-stud.
3.Rotate the roof molding in the direction of arrows shown in the figure while pulling it up and remove it
starting from the clips at the front of the vehicle.
5.Move the remover tool in the direction of the arrows shown in the figure and detach the roof molding
from the rear T-stud.
id091600447600
1.Press the roof molding in the direction of arrow (1) shown in the figure and install it to the front T-stud.
ac5uuw00007255
2.Hook the roof molding to the clip and attach the roof molding while pressing it in the direction of arrow
(2) shown in the figure.
3.Press the roof molding in the direction of arrow (3) shown in the figure and install it to the rear T-stud.
4.Press the protectors installation positions in the direction of arrow (4) shown in the figure and firmly
adhere them to the body.
id091600801700
3.Remove the bolts from curtain air bag module and set it aside so that it does not interfere with the
servicing. (See CURTAIN AIR BAG MODULE REMOVAL/INSTALLATION [STANDARD DEPLOYMENT
CONTROL SYSTEM - MEXICO SPEC.].) (See CURTAIN AIR BAG MODULE
REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM - US/CANADA SPEC.].)
id091600801600
Replace parts
Number of parts: 2
Warning
• Using a utility knife with bare hands can cause injury. Always wear gloves when using a utility knife.
2.Remove the liftgate upper trim. (See LIFTGATE UPPER TRIM REMOVAL/INSTALLATION.)
6.Move the wiring harness and remove it from the wiring harness clip.
ac5uuw00007265
7.Attach a piece of wire between the liftgate striker and liftgate latch to hold the liftgate in the half-opened
position as shown below.
8.Remove the double-sided adhesive tape in the position shown in the figure using the utility knife.
10.Perform the same procedure from Steps 8 and 9 for the opposite side of the vehicle.
Caution
• When removing the rear spoiler, the rear spoiler may fall and be damaged. Perform the rear spoiler
clip removal using two people.
11.Pull the rear spoiler in the direction of the arrows shown in the figure and remove it while detaching
clips.
id091600446100
(1)Liftgate upper trim (See LIFTGATE UPPER TRIM REMOVAL/INSTALLATION.) (2)Liftgate side
trim (See LIFTGATE SIDE TRIM REMOVAL/INSTALLATION.) (3)Liftgate recess (See LIFTGATE
RECESS REMOVAL/INSTALLATION.) (4)Power liftgate (PLG) rear switch (With power liftgate) (See
POWER LIFTGATE (PLG) REAR SWITCH REMOVAL/INSTALLATION.) (5)Liftgate lower trim (See
LIFTGATE LOWER TRIM REMOVAL/INSTALLATION.) (6)Liftgate garnish (See LIFTGATE
GARNISH REMOVAL/INSTALLATION.) (7)Request switch (liftgate) (See REQUEST SWITCH
REMOVAL/INSTALLATION.) (8)Rear mount camera (With rear mount camera) (See REAR
MOUNT CAMERA REMOVAL/INSTALLATION.)
ac5uuw00008350
ac5uuw00007276
8.Insert a tape-wrapped flathead screwdriver in the position shown in the figure, move it in the direction of
the arrow to remove the clips.
ac5uuw00007278
10.Perform the same procedure from Steps 7 to 9 for the opposite side of the vehicle.
id091600468000
2.Remove the seal board upper. (See SEAL BOARD UPPER REMOVAL/INSTALLATION.)
ac5uuw00007222
6.Detach the tabs of the front bumper face from the radiator grille.
id091600467600
Front mudguard
ac5uuw00007257
4.Remove the front over fender. (See FRONT OVER FENDER REMOVAL/INSTALLATION.)
LH
RH
ac5jjw00008161
7.Pull the front mudguard in the direction of the arrow shown in the figure.
Rear mudguard
LH
RH
ac5uuw00009425
id091600888900
ac5uuw00007393
id091600888800
ac5uuw00007392
id091600820200
ac5uuw00008001
id091600801500
3.Insert a tape-wrapped flathead screwdriver shown in the figure and remove the tab in the direction of
arrow (1).
ac5uuw00008354
id091600900500
Front deflector
ac5uuw00009431
3.Pull the front deflector in the direction of the arrow shown in the figure and remove it while detaching the
hooks.
Rear deflector
id091600801000
1.Remove the windshield wiper arm and blade. (See WINDSHIELD WIPER ARM AND BLADE
REMOVAL/INSTALLATION.)
ac5uuw00008353
ac5uuw00007220
6.Pull the cowl grille in the direction of the arrow shown in the figure and detach the guides from the
windshield.
ac5uuw00007221