1. Safety precautic
The following symbol mean:
A Caution: Read these operating instructions fully before use and pay
particular attention to sections containing this symbol
+ Use only as specified by the operating instructions, or the intrinsic protection
may be impaired.
+ After transport or storage in humid conditions, dry out the unit before connecting
it to the supply voltage. During drying out the intrinsic protection may be
impaired
+ Connect only to a power supply with a voltage corresponding to that on the
serial number label.
+ Do not use other power supply units than recommended by the manufacturer.
+ Ensure that the mains switch and isolating device (power supply connector) are
easily accessible during use.
+ Do not operate the unit outside the laboratory premises.
+ Do not operate the unit in premises with aggressive or explosive chemical
mixtures.
« Before moving, disconnect at the power supply socket.
+ Do not start operation at maximum speed.
+ Do not use the tubes bigger than 28,5 mm in diameter.
+ Do not stop the vortex head or platform rotation with a hand during operation.
+ If liquid is spilt inside the unit, disconnect it from the power supply and have it
checked by a competent person.
+ Before using any cleaning or decontamination method except those
recommended by the manufacturer, user should check with the manufacturer
that the proposed method will not damage the equipment.
+ The unit should be saved from shocks and falling.
impulsado por CamScanner2. General |. ormation
ed for mixing substances in tubes using the
din a variety of applications including general
cell's suspensions vortexing, chemical
Personal Vortex V-1 plus is design
eccentric mechanism. Vortex can be use
test tube mixing, tissue samples mixing,
reagents mixing, etc.
The vortex is equipped with 20 mm diameter single Polystyrol mixing cup for mixing
one tube ata time.
Vortex V-1 plus is intended for two operations:
- continuous mixing;
- intermittent mixing (activated by touching the mixing cup with a test tube).
Vortex V-1 plus operates at variable speeds from 750 to 3000 RPM providing
different mixing intensity (from gentle shaking to vigorous vortexing).
impulsado por CamScanner3.1. Unpacking
Remove packing materials carefully and retain for future shipment or storage of
the unit.
3.2. Complete set
The unit set includes:
ITEM QUANTITY INTHE SET |
Personal vortex V-1 plus 1 pce. |
External power supply unit 1 pce. |
Operating Manual; Specifications; Certificate 1 copy \
3.3. Setup
— place the unit on the working area;
- plug the external power supply unit into the 12 V socket at the rear side of the
unit.
impulsado por CamScanner4.1, Connect the external power supply unit to the mains.
4.2. Continuous operation mode-CS
4.2.1. Tum the TS/CS switch (fig-1 /2) into position cs.
4.2.2. Adjust the necessary speed using the Speed knob (+ )
4.2.3. Gently holding a tube with two fingers at its upper pari dip the tube’s lower
part into the conic deepening of the vortex head (Polystyrol cup) (Fig.2/1).
Control the intensity of mixing by varying pressure of a tube to the vortex
head.
4.2.4.Atthe end of operation turn the TS/CS switch into positi
4.3. Touch operation mode-TS
4.4.1. Tum the TS/CS switch (fig.1/2) into position TS.
4.4.2.Gently holding a tube with two fingers at its upper part dip the tube's lower
part into the conic deepening of the vortex head (Fig.1/1 ). Vortex will be
activated when pressing the mixing cup witha testtube.
4.4.3. Adjust the necessary speed (desired mixing level) using
the Speed knob (fig. 1/3).
4.4.4. Control the intensity by varying pressut
to the Polystyrol cup (Fig.1/1).
4.4. Atthe and of operation disconnect the power supp!
ion TS.
re of a tube
ly unit from the mains.
Fig.1 Personal vortex V-1 plus
impulsa
pulsado por CamScanner