Professional Documents
Culture Documents
Service Manuals LG TV LCD 42LG61YD 42LG61YD Service Manual
Service Manuals LG TV LCD 42LG61YD 42LG61YD Service Manual
website:http://biz.LGservice.com
MODEL : 42LG61YD
CAUTION
42LG61YD-AC
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
CONTENTS .............................................................................................. 2 PRODUCT SAFETY ..................................................................................3 SPECIFICATION ........................................................................................6 ADJUSTMENT INSTRUCTION ...............................................................12 TROUBLE SHOOTING ............................................................................18 BLOCK DIAGRAM...................................................................................22 EXPLODED VIEW .................................................................................. 34 SVC. SHEET ...............................................................................................
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-2-
SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.
AC Volt-meter
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.
0.15uF
1.5 Kohm/10W
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-3-
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First. General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver. Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.) General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500F to 600F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature. (500F to 600F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suctiontype solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuit board printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature (500F to 600F) b. First, hold the soldering iron tip and solder the strand against the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.
-4-
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above. Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas). "Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection. Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink. Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder. Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top. 3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered. At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections). 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire. At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board. 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.
-5-
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This specification is applied to the LCD TV used LB81B/C chassis.
3. Test method
1) Performance: LGE TV test method followed 2) Demanded other specification - Safety: CB specification - EMC: CISPR 13 specification
4. General specification
Item Broadcasting system Available Channel 1) VHF : 00~12 2) UHF : 20~75 3) CATV : 02~44 4) DTV : 06~12, 27~69 Tuner IF 1) PAL : 38.90MHz(Picture), 34.40MHz(Sound) 2) DVB-T : 36.125MHz Input Voltage Screen Size AC 100~240V, 50/60Hz 42 inch Wide (1920 x 1080) 47 inch Wide (1920 x 1080) 52 inch Wide (1920 x 1080) Aspect Ratio Module 16:9 LC420WUE-SAB1 LC470WUE-SAB1 LC420WUF-SAB1 LC470WUF-SAB1 LK520D3LZ9X LC420WUF-SSA LC470WUF-SAT1 Operating Environment Storage Environment 1) Temp : 0 ~ 40 deg 2) Humidity : ~ 80 % 1) Temp : -20 ~ 60 deg 2) Humidity : ~ 85 % 42LG60FD-AB 47LG60FD-AB 42LG65YD-AA 47LG65YD-AC 52LG65YD-AC 42LG61YD-AC 47LG61YD-AC LGE Spec Specification PAL-BG, DTV:DVB-T Remark
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-6-
5-2. 47LG65YD-AC
No 1. 2. 3. 4. Contrast ratio Brightness uniformity Color coordinate RED GREEN BLUE WHITE 5. 6. Color coordinate uniformity Contrast ratio 900 1300 X Y X Y X Y X Y 70 Typ. -0.03 0.638 0.335 0.289 0.609 0.145 0.063 0.279 0.292 N/A All mode execpt RGB/HDMI-PC (With PWM Dimiming) RGB/HDMI-PC (Without PWM Dimining) 7. 8. 9. 10. Color Distortion, DG Color Distortion, DP Color S/N, AM/FM Color Killer Sensitivity TBD TBD TBD TBD % deg dB dBm Typ. +0.03 Item White peak brightness Min 400 Typ 500 Max Unit cd/m2 cd/m2 % N/A Full white Color coordinate Remark
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-7-
5-3. 52LG65YD-AC
No 1. 2. 3. 4. Contrast ratio Brightness uniformity Color coordinate RED GREEN BLUE WHITE 5. 6. Color coordinate uniformity Contrast ratio X Y X Y X Y X Y 70 Typ. -0.03 0.640 0.330 0.280 0.600 0.150 0.060 0.272 0.277 N/A All mode execpt RGB/HDMI-PC (With PWM Dimiming) RGB/HDMI-PC (Without PWM Dimining) 7. 8. 9. 10. Color Distortion, DG Color Distortion, DP Color S/N, AM/FM Color Killer Sensitivity TBD TBD TBD TBD % deg dB dBm Typ. +0.03 Item White peak brightness Min 360 Typ 450 Max Unit cd/m2 cd/m2 % N/A Full white Color coordinate Remark
5-4. 42LG61YD-AC
No 1. 2. 3. 4. Contrast ratio Brightness uniformity Color coordinate RED GREEN BLUE WHITE 5. 6. Color coordinate uniformity Contrast ratio 1000 (800) 1400 (1000) X Y X Y X Y X Y 70 Typ. -0.03 0.640 0.335 0.289 0.610 0.144 0.066 0.279 0.292 N/A All mode execpt RGB/HDMI-PC (With PWM Dimiming) RGB/HDMI-PC (Without PWM Dimining) 7. 8. 9. 10. Color Distortion, DG Color Distortion, DP Color S/N, AM/FM Color Killer Sensitivity TBD TBD TBD TBD % deg dB dBm Typ. +0.03 Item White peak brightness Min 360 Typ 450 Max Unit cd/m2 cd/m2 % N/A Full white Color coordinate Remark
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-8-
5-5. 47LG61YD-AC
No 1. 2. 3. 4. Contrast ratio Brightness uniformity Color coordinate RED GREEN BLUE WHITE 5. 6. Color coordinate uniformity Contrast ratio 900 1300 X Y X Y X Y X Y 70 Typ. -0.03 0.638 0.335 0.289 0.610 0.145 0.063 0.279 0.292 N/A All mode execpt RGB/HDMI-PC (With PWM Dimiming) RGB/HDMI-PC (Without PWM Dimining) 7. 8. 9. 10. Color Distortion, DG Color Distortion, DP Color S/N, AM/FM Color Killer Sensitivity TBD TBD TBD TBD % deg dB dBm Typ. +0.03 Item White peak brightness Min 360 Typ 450 Max Unit cd/m2 cd/m2 % N/A Full white Color coordinate Remark
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
-9-
7. RGB PC INPUT
No 1 2 3 4 5 6 7 8 9 Resolution 720*400 640*480 800*600 1024*768 1280*768 1360*768 1366*768 1280*1024 1920*1080 H-freq(kHz) 31.468 31.469 37.879 48.363 47.78 47.72 47.56 63.595 66.647 V-freq.(Hz) 70.08 59.94 60.31 60.00 59.87 59.8 59.6 60.0 59.988 Pixel clock(MHz) 28.321 25.17 40.00 65.00 79.5 84.75 84.75 108.875 138.625 VESA VESA VESA(XGA) WXGA WXGA WXGA SXGA WUXGA FHD Model only FHD Model only Input 848*480 60Hz, 852*480 60Hz => 640*480 60Hz Display Proposed Remark
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 10 -
HDTV 1080I 50 Hz HDCP HDTV 1080P 24Hz HDCP HDTV 1080P 50Hz HDCP HDTV 1080P HDTV 1080P HDCP HDCP
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 11 -
ADJUSTMENT INSTRUCTION
1. Application Range
This specification sheet is applied to all of the LCD TV with LB81C chassis. 5. Click Auto tab and set as below 6. Click Run. 7. After downloading, check OK message.
(5) filexxx.bin
2. Designation
1) The adjustment is according to the order which is designated and which must be followed, according to the plan which can be changed only on agreeing. 2) Power Adjustment: Free Voltage 3) Magnetic Field Condition: Nil. 4) Input signal Unit: Product Specification Standard 5) Reserve after operation: Above 5 Minutes (Heat Run) Temperature : at 255C Relative humidity : 6510% Input voltage : 220V, 60Hz 6) Adjustment equipments: Color Analyzer (CA-210 or CA110), Pattern Generator (MSPG-925L or Equivalent), DDC Adjustment Jig equipment, SVC remote controller 7) Dont push The IN STOP KEY after completing the function inspection.
(6)
(7) ........ OK
* USB DOWNLOAD
1) Put the USB Stick to the USB socket
USB
* Download
1) Execute ISP program Mstar ISP Utility and then click Config tab. 2) Set as below, and then click Auto Detect and check OK message. If display Error, Check connect computer, jig, and set. 3) Click Connect tab. If display Cant, Check connect computer, jig, and set.
(1) (3)
2) Automatically detecting update file in USB Stick - If your downloaded program version in USB Stick is Low, it didnt work. But your downloaded version is High, USB data is automatically detecting 3) Show the message Copying files from memory
4) Updating is staring.
Please Check Speed : To us speed between from 200 KHz to 400 KHz (2) OK
4) Click Read tab, and then load download file(XXXX.bin) by clicking Read. 5) Fishing the version uploading, you have to put USB stick and AC Power off.
(4) filexxx.bin
- 12 -
Impress Resolution 1080i Model : 223 in Pattern Generator(1080i Mode) Pattern: 65 in Pattern Generator (MSPG-925 Series, MPSG-1025D) - 7 color bar. - Adjust by commanding AUTO_COLOR_ADJUST. 2) Confirmation - We confirm whether 0xB3 (480i)/0xBC (1080i) address of EEPROM 0xA2 is 0xAA or not. - If 0xB3 (480i)/0xBC(1080i) address of EEPROM 0xA2 isnt 0xAA, we adjust once more. - We can confirm the ADC values from 0xAD~0XB2 (480i)/0XB6~BB (1080i) addresses in a page 0xA2. * Manual ADC process using Service Remocon. After enter Service Mode by pushing ADJ key, execute ADC Adjust by pushing G key at ADC CALIBRATION : COMPONENT. Impress Resolution 480i
<Fig. 1> Adjustment pattern(PC) - Adjust by commanding AUTO_COLOR_ADJUST. 2) Confirmation - We confirm whether 0xAA (RGB) address of EEPROM 0xA2 is 0xAA or not. - If 0xAA (RGB) address of EEPROM 0xA2 isnt 0xAA, we adjust once more - We can confirm the ADC values from 0xA4~0XA9 (RGB) addresses in a page 0xA2 * Manual ADC process using Service Remocon. After enter Service Mode by pushing ADJ key, execute ADC Adjust by pushing G key at ADC CALIBRATION: RGB-PC. Impress Resolution 1080i
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 13 -
(5) Adjust Process will finish by execute I2C Command (Inner pattern (Inner pattern (0xF3,0x00)). ** Caution ** Color Temperature: COOL, Medium, Warm One of R Gain/G Gain/ B Gain should be kept on 0xC0, and adjust other two lower than C0. (when R/G/B Gain are all C0, it is the FULL Dynamic Range of Module) * Manual W/B process using adjusts Remote control. - After enter Service Mode by pushing ADJ key, - Enter White Pattern off of service mode, and change off ---> on. - Enter W/B ADJUST by pushing G key at 3.W/B ADJUST. - The default value of RGB-GAIN is 192 at cool, Medium, Warm (There is a difference between picture image and set)
* After done all adjustments, Press In-start button and compare Tool option and Area option value with its BOM, if it is correctly same then unplug the AC cable. If it is not same, then correct it same with BOM and unplug AC cable. For correct it to the models module from factory JIG model. * Dont push The IN STOP KEY after completing the function inspection.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 14 -
EDID block 1, Bytes 128-255[80H- FFH] Block Type : CEA EDID Timing Extension Version 3.
0 10 20 30 40 50 60 70 0 02 22 00 88 00 2C 20 00 1 03 1F B0 21 13 45 58 1E 2 23 10 2D 00 8E 00 2C 30 3 4 5 F1 4E 81 23 15 07 01 1D 00 00 1E 8C 21 00 00 06 44 21 25 00 C4 40 80 37 6 02 50 80 0A 18 00 8E 00 7 03 83 51 D0 02 00 21 BC 8 15 01 D0 8A 3A 1E 00 88 9 A B C D 12 13 04 14 05 00 00 67 03 0C 1C 20 40 80 35 20 E0 2D 10 10 80 18 71 38 2D 01 1D 80 18 71 00 9E 4E 1F 00 21 00 00 18 00 E F 20 21 00 20 00 BC 3E 96 40 58 1C 16 80 51 00 CF 0 10 20 30 40 50 60 70
EDID block 1, Bytes 128-255[80H- FFH] Block Type : CEA EDID Timing Extension Version 3.
0 02 22 00 88 00 2C 20 00 1 03 1F B8 21 13 45 58 1E 2 23 10 2D 00 8E 00 1C 30 3 4 5 F1 4E 81 23 15 07 01 1D 00 00 1E 8C 21 00 00 06 44 21 14 00 C4 40 80 37 6 02 50 80 0A 18 00 8E 00 7 03 83 51 D0 02 00 21 BC 8 15 01 D0 8A 3A 1E 00 88 9 A B C D 12 13 04 14 05 00 00 67 03 0C 1C 20 40 80 35 20 E0 2D 10 10 80 18 71 38 2D 01 1D 80 18 71 00 9E 4E 1F 00 21 00 00 18 00 E F 20 21 00 40 00 BC 3E 96 40 58 1C 16 80 51 00 AF
1) All Data : HEXA Value 2) Changeable Data : *: Serial No : Controlled / Data:01 **: Month : Controlled / Data:00 ***:Year : Controlled ****:Check sum
EDID block 1, Bytes 128-255[80H- FFH] Block Type : CEA EDID Timing Extension Version 3.
0 10 20 30 40 50 60 70 0 02 22 00 88 00 2C 20 00 1 03 1F B0 21 13 45 58 1E 2 23 10 2D 00 8E 00 2C 30 3 4 5 F1 4E 81 23 15 07 01 1D 00 00 1E 8C 21 00 00 06 44 21 25 00 C4 40 80 37 6 02 50 80 0A 18 00 8E 00 7 03 83 51 D0 02 00 21 BC 8 15 01 D0 8A 3A 1E 00 88 9 A B C D 12 13 04 14 05 00 00 67 03 0C 1C 20 40 80 35 20 E0 2D 10 10 80 18 71 38 2D 01 1D 80 18 71 00 9E 4E 1F 00 21 00 00 18 00 E F 20 21 00 30 00 BC 3E 96 40 58 1C 16 80 51 00 BF
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 15 -
5. Adjustment Command
5.1. I2C(100K BPS) 5.2. COMMUNICATION START
START 6E A STOP 50Ms
a. LEN : DATA BYTE number to send b. CMD : Command language theat monitor executes. c. VAL : FOS DATA d. CS : Dadas CHECKSUM that transmit e. DELAY : 50Ms f. A : Acknowledge
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 16 -
128 Bytes
LEN : 84h+Bytes CMD : 8Eh ADH : E2PROM Slave Address(A0,A2,A4,A6,A8), Not 00h (Reserved by Buffer To EEPROM) ADL : E2PROM Sub Address(00~FF) Data : Write data (2) Command Set
Adjustment item EEPROM WRITE CMD(hex) E8 LEN 94 84+n Remark 16-Byte Write n-byte Write
* Purpose 1) EDID write : 16-byte by 16-byte, 8 order (128-byte) write(TO 00 7F of EEPROM Page A4). 2) FOS Default write : 16-mode data (HFh, HFl, VF, STD, HP, VP, Clk, ClkPh, PhFine) write 3) Random Data write : write the appointment Address of E2PROM.
MICOM) - Be transmitted the contents of MICOMs 128-bytes Buffer to PC. (128th Data is the CheckSum of 127-bytes data : Thats OK if the value of adding 128-bytes Data is Zero)
START 6F A Data 1 ... Data 128 A CS NA STOP
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 17 -
TROUBLESHOOTING
1. TV/CATV doesnt display
Check T U401 Pin 15(Vid eo ou tp ut), Pin1 6(Sound output) Can you see t he normal sign al?
NO
Could you measu re voltag e of TU800 & IIC lines? Are they all normal?
YES
NO
YES
You sh ou ld rep lace TUNER. Check th e output of TR(Q503). Can you see t he normal wavefo rm?
YES
NO
Check th e output of Main IC(IC100). Esp ecially you sh ould ch eck The H,V sync and c loc k. Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e Power of Main IC(IC100) you should decide to replace Main IC or not .
This bo ard has b ig problem becau se Main IC(IC100) have some troubles. Afte r c hecking thoro ugh ly all pa th onc e again, You sh ou ld decid e to rep lace Main Bo ard or no t.
Could you measu re voltag e of TU800 & IIC lines? Are they all normal?
YES
NO
Check th e output of Main IC(IC100). Esp ecially you sh ould ch eck The H,V sync and c loc k. Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e Power of Main IC(IC100) you should decide to replace Main IC or not .
This bo ard has b ig problem becau se Main IC(IC100) have some troubles. Afte r c hecking thoro ugh ly all pa th onc e again, You sh ou ld decid e to rep lace Main Bo ard or no t.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 18 -
J600,J 601 or SIDE AV may have problem. Replace th is Jack o r SIDE AV.
Check th e in pu t o f Vid eo switch (IC700). Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e Power of AV switch you should decide to replace AV switch or not.
Check th e output of Main IC(IC100). Esp ecially you sh ould ch eck The H,V sync and c loc k. Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e Power of Main IC(IC100) you should decide to replace Main IC or not .
This bo ard has b ig problem becau se Main IC(IC100) have some troubles. Afte r c hecking thoro ugh ly all pa th onc e again, You sh ou ld decid e to rep lace Main Bo ard or no t.
Check th e in pu t o f Compo nent Audio switch (IC1001) , Can you see t he normal wavefo rm?
NO
Afte r c hecking the Power of compone nt Audio switch, y ou should decide to replace component Audio s witch or not.
YES
Check th e output of Comp on ent Audio switch (IC1001) , Can you see t he normal wavefo rm?
YES
NO
Afte r c hecking the Power of compone nt Audio switch y ou should decide to replace component Audio s witch or not.
Check th e output of Main IC(IC100). Esp ecially you sh ould ch eck The H,V sync and c loc k. Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e Power of Main IC(IC100) you should decide to replace Main IC or not .
This bo ard has b ig problem becau se Main IC(IC100) have some troubles. Afte r c hecking thoro ugh ly all pa th onc e again, You sh ou ld decid e to rep lace Main Bo ard or no t.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 19 -
Check th e in pu t o f RGB Video switch (IC700) , Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e Power of RGB Vid eo switc h, you should decide to replace RGB Video switch or not.
Check th e in pu t o f RGB Audio switch (IC1001) , Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e Power of RGB Audio sw itc h, you should decide to replace RGB Audio s witch or not.
Check th e output of RGB Audio switch (IC1001) , Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e Power of RGB Audio sw itc h you should decide to replace RGB Audio s witch or not.
Check th e output of Main IC(IC100). Esp ecially you sh ould ch eck The H,V sync and c loc k. Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e Power of Main IC(IC100) you should decide to replace Main IC or not .
This bo ard has b ig problem becau se Main IC(IC100) have some troubles. Afte r c hecking thoro ugh ly all pa th onc e again, You sh ou ld decid e to rep lace Main Bo ard or no t.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 20 -
NO
Check th e in pu t o f HDMI Seitch (IC902) This sign al is TMDS. Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e trace o f TMDS lin es and po wer of HDMI Switch, you should decide to replace HDMI Switch or not .
Check th e output of HDMI Switc h(IC902). Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e Power of HDMI Switch y ou should decide to replace MST3361 or not.
Check th e output of Main IC(IC100). Esp ecially you sh ould ch eck The H,V sync and c loc k. Can you see t he normal wavefo rm?
YES
NO
After ch eckin g th e Power of Main IC(IC100) you should decide to replace Main IC or not .
This bo ard has b ig problem becau se Main IC(IC100) have some troubles. Afte r c hecking thoro ugh ly all pa th onc e again, You sh ou ld decid e to rep lace Main Bo ard or no t.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 21 -
2 $0.46 5V 2.5_DDR
TS1_CLK TS1_SYNC TS1_VLD TS1_D0 IN[A2] OUT[A1] SCL_D_TU SDA_D_TU TU_TS_CLK TU_TS_SYNC TU_TS_VAL TU_TS_DATA[0]
TV_CVBS+(1.8Vp-p) SIF+(96dBuV)
CVBS0P SIF_IN1P SCL_A_TU SDA_A_TU
IN1
0IMMR00141A
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
Side Y/C
M-STAR
LVDS(8Bit)
ROMSCK[35]
L C D
CVBS_Out
3 3
OUT1
Comp_1 YPbPr
BLOCK DIAGRAM
512K 3.3V
Comp_2 YPbPr
DDC_SCL/UART_Rx DDC_SDA/UART_Tx
Air : DVB/PAL ROMSD[36] RGB/YPbYr*2 CVBS*2 YC*1 SPI_CK[171] SPI_DI[172] L/R-IN*3 SPI_DO[173] SIF SPI_CZ[174] CVBS OUT*1
EAN32213401 Power
KEY_CTL[1,2,3]
PC(VGA)
Rx_In
Tx/Rx
(IC603)
MAX3232CDR R232C_TXD
R232C_RXD
RS232C(Debu g)
Tx_Out
PB_IN[11] SOY[13] Y_IN[14] SAR3[204] PR_IN[16] SAR2[203] AUL_IN1[70] SAR1[202] AUR_IN1[71] SAR0[201] BIN[1]SOGIN[2]GIN[3]RIN[4] IR_RX[57] VS_RGB[7] HS_RGB[8] SCL/RX[33] SDA/TX[34] DM_DET[ AUOUTL0[79] AUOUTR0[80]GPIO12[45]
Power/LIP S Power/LIP S
Audio_L
IN_L[38]
Audio_R
IN_R[5] MUTE[6]
D-AMP
HP_OUT_L[42] HP_OUT_R[1]
HeadPhone
(YDA138) 0IPRPTI030B
HP_DET[37]
OUT_P_R[8] OUT_N_R[14]
R OUT
6612F00099A $0.27617
USB(SW Upgrade)
HeadPhone $0.86
OUT_P_L[35] OUT_N_L[29]
EAG31022001 $0.185
L OUT
ANT
1.8V 3.3V
CLK _14.3L6AF
6212AA2004F 2 2.5_DDR $0.46 5V
IN[256] OUT[255] TS0-7[96,97,98,99,100,101,102,103]
12V
MP1593DN-LF 0IPMG00063A
$0.0623
1.0Vp-p
96dBuV SIF
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
[11]
IN1
L C D LVDS(8Bit)
EEPROM(32K) EEPROM(32K) 24C32 24C32
M-STAR
Rear AV_2 V, LR
- 23 $0.076
EEPROM 0IMMR00014A
Side A V_3
5V Changed 32K $0.145 - $0.76 0IMMRAL025A $0.67 SST25VF016B SST25VF016B EAN32213401 Power
KEY_CTL[1,2,3]
512K 3.3V
Flash(16 M) Flash(16 M)
V,LR
Side S_3
YC
MNT_V,LR_Out
Comp_1 YPbPr/LR
6612J10031A $0.25744
Cable : 256/64QAM RGB/YPbYr*2 CVBS*3 SPI_CK[171] SPI_DI[172] YC*2 SPI_DO[173] L/R-IN*3 SPI_CZ[174] SIF SAR3[204] CVBS OUT*1 SAR2[203]
Comp_2 YPbPr/LR PC IN
12V
PC(VGA) $0.23975
Power/LIP S Power/LIP S
6630G70016A
AUR_IN3[76] AUL_IN3[75]
PC EarPhone
(ICL3232)
Rx_In 0IPRP00009A $0.32 0IMX232162A $0.4 Tx_Out
Tx/Rx
ST-5V
PB_IN[11] SOY[13] Y_IN[14] PR_IN[16] AUL_IN1[70] SAR1[202] AUR_IN1[71] SAR0[201] BIN[1]SOGIN[2]GIN[3]RIN[4] IR_RX[57] VS_RGB[7] HS_RGB[8] SCL/RX[33] SDA/TX[34] DM_DET[ AUOUTL0[79] AUOUTR0[80]GPIO12[45]
6612F00099A $0.27617
Audio_L
IN_L[38]
Audio_R
IN_R[5] MUTE[6] HP_OUT_L[42] HP_OUT_R[1]
RS232C(Debu g)
6630G70017A $0.21984
D-AMP
(NTP3000) 0IPRPTI030B
HP_DET[37]
HeadPhone
OUT_P_R[8] OUT_N_R[14]
R OUT
6612F00099A $0.27617
USB(SW Upgrade)
EAG31022001 $0.185
$0.86
OUT_P_L[35] OUT_N_L[29]
L OUT
IF_N TS[0-7]
MSD2379A
[MSTAR]
TS_DATA
IF_P
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
LPF
TS_CLK TS_SYNC
Buffer
SIF
Buffer
TUNER_CVBS
DDC_I2C E2PROM_I2C
IF_N TS[0-7]
MSD2379A
[MSTAR]
TS_DATA
IF_P
IF_AGC TS_VALID
LPF
TS_CLK TS_SYNC
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
Buffer
SIF
Buffer
TUNER_CVBS
DDC_I2C E2PROM_I2C
Signal Video
Add sy nc p attern of each input/output
MStar
(From Tuner) AT_TU_V
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
[MSD2379A]
CVBS0 CVBS1 SVIDEO ( Y/C )
CVBS1
- 26 RGB
Component ( Y/Cb/Cr )
MSD2379A
[MSTAR]
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
TS_DATA
AU_OUT0_ L/R
NT 000 P3
SPEAKER Output
COMPONENT_L/R
DSUB RGB_L/R
M-STAR
57 IR IN[MSD2379
IR A]
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
Local Key
KEY_CTL_0 KEY_CTL_1 202 SAR1 201 SAR0
- 28 -
The I/O tol erance is 3.3V maximum for use. scale of MSD1226L is 1.8V.
$0.46
12V 12V
0.6A 265mA Sound Mute 12V Option Pannel 23 EEPROM AT24C32AN
IC800 MP1583DN-Z
15V
15V
IC800 MP1583DN-Z
5V
TUNER
15V
15V
GND 3
GND 3
GND 4
GND 4
5V
5V
0.4A
5V
5V
ACD 7
GND 7
PWR_ON 8
NC 8
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
IC803 AZ1117H-3.3V
ST_3.3V
274.6mA IR
INV_CTL 9
INV_CTL 9
DIM 10
DIM 10
INV_BR 11
INV_BR 11
MSD1226L
VDDP VDDQ
6.3V 12
IC804 AZ1117H-3.3V
ST_3.3V
72.4mA
$0.17
IC807 KIA78R05F
Outp ut Curr ent : 5A
IC802 KD1084ADT-R
ST_1.8V
465mA
VDDC
FET 5203
800mA
3.3V
248mA
1.8V
570mA
LGDT3303
VDD AVDD
0.4A
Pannel 20
$0.46
12V 12V
0.6A 265mA Sound Mute 12V Option Pannel 23 EEPROM AT24C32AN Sound Amp YDA138
IC800 MP1583DN-Z
15V
15V
IC800 MP1583DN-Z
Outp ut Curr ent : 3A Input : 4.75V to 23V Output : 1.22V to 21V
5V
TUNER
15V
15V
GND 3
GND 3
GND 4
GND 4
5V
5V
0.4A
5V
5V
ACD 7
GND 7
PWR_ON 8
NC 8
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
IC803 AZ1117H-3.3V
ST_3.3V
274.6mA IR
INV_CTL 9
INV_CTL 9
DIM 10
DIM 10
INV_BR 11
INV_BR 11
MSD1226L
VDDP VDDQ
6.3V 12
IC804 AZ1117H-3.3V
ST_3.3V
72.4mA
$0.17
IC807 KIA78R05F
Outp ut Curr ent : 5A
IC802 KD1084ADT-R
ST_1.8V
465mA
VDDC
FET 5203
800mA
3.3V
248mA
VDD
1.2V
570mA
VDD
MSD809
0.4A
Pannel 20
DDC_SCL DDC_DSA EEPROM 24C21A M2_A[0:11] M2_DQ[0:15] M2_DQM0 M2_DQM1 M2_CKE M2_MCLK CKE MCLK VGA_RX VGA_TX SDRAM 4M*16Bit
SDA[5] SCL[6]
I2C_SDA I2C_SCL
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
SDRAM 4M*16Bit
ATSC/NTSC TUNER
LGDT3303
SCL[48] SDA[49]
MSD1226L
SPI_CK[171] SPI_DI[172] SPI_DO[173] SPI_CZ[174]
DDC_SCK[33] SCL/RX DDC_SD[34] SDA/TX SCLM1[59] SDAM1[60] MSCL MSDA UATX1[55] UARX1[56] DDC_ROMSCK[35] DDC_ROMSD[36] SPI_CK SPI_DI SPI_DO SPI_CZ FLASH SST25VF016B
SDRAM 4M*16Bit
Debug Port
5V IIC
3.3V IIC
Mstar [MSD1226L ]
ATSC/NTSC Tuner
+3.3V 4.7K
I2C Address
MSCL/MSDA
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
DDC_ROM SCL/SDA
- 32 -
Mstar [MSD1226L ]
SPI_CSZ SPI_DO SPI_DI SI SPI_CK
CSZ
SDO
SDI
SCK
SCLK
MEMO
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
- 33 -
EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
400
521
840
570
520
804
830
805
540
801
803
200
510
802
560
300
121
500
120
810
530
900
+3.3V_VDDP_ST
A14 C15 B15 B7 A7 B3 A3 B4 A4
R1018 10K CLKE 22 MCLK+ MCLKR1187 22 22 R1107 R1085 VD33_1 VD33_2 VD33_3 VD33_4 VD33_2_1 VD33_2_2 G6 ST_BY 3.3V
SDR_DQS_1 SDR_DQM_1 SDR_DQ_8 SDR_DQ_9 SDR_DQ_10 SDR_DQ_11 SDR_DQ_12 SDR_DQ_13 SDR_DQ_14 SDR_DQ_15 SDR_DQS_2 SDR_DQM_2 SDR_DQ_16 SDR_DQ_17 SDR_DQ_18 SDR_DQ_19 SDR_DQ_7
IC100 LGE7363C-LF
+3.3V_VDDP P11 P12 P13 P14 P9
SDR_DQ_5
PANEL_CTL
009:B5;009:E16 RL_ON AVDD_33_1 AVDD_33_2 AVDD_33_3 AVDD_33_4 AVDD_33_5 AVDD_33_6 AVDD_MPLL +3.3V_AVDD_LPLL AVDD_MEMPLL AVDD_USB GPIO AVDD_LPLL_1 AVDD_LPLL_2 AVDD_AU AVDD_SIF AVDD_DDR_1 AVDD_DDR_2 AVDD_DDR_3 MVREF C164 AVDD_DVI_2 VDDC_1 VDDC_2 VDDC_3 H14 J14 K14 L14 M14 N14 P7 P8 C159 0.1uF 50V C162 0.1uF 50V C160 0.1uF 50V VDDC_4 VDDC_5 VDDC_6 VDDC_7 VDDC_8 VDDC_9 VDD_PWR AVDD_RTC C156 0.1uF 50V G14 +1.25V_VDDC N6 1% M6 C155 0.1uF 50V 0.1uF AVDD_DVI_1 G9 R1120 1K +1.25V_AVDD_DVI G8 C163 1000pF 1K 1% A15 R1121 +2.5V_VDD_DDR G10 G11 C154 0.1uF 50V G13 +2.5V_VDD_DDR P3 C169 0.1uF 50V C168 0.1uF 50V C167 0.1uF 50V C161 0.1uF 50V +3.3V_AVDD_OTG C165 0.1uF 50V DQS2 DQM2 MDATA[16] MDATA[17] MDATA[18] MDATA[19] MDATA[20] MDATA[21] MDATA[22] MDATA[23] +3.3V_AVDD_MPLL +3.3V_AVDD_MEMPLL C153 0.1uF 50V C158 0.1uF 50V
Q100 2SC3052
R1013 B 10K
006:M22 RS232C_RXD RS232C_TXD 001:S5;001:AB11 SYSTEM_SDA SYSTEM_SCL DDC_SDA/UART_TX 005:AB18 DDC_SCL/UART_RX FRC_RESET EEPROM_WP 006:AE24 USB_CTL 006:AM7 MUTE_AV_L/R 001:AC18 Flash_WP_1
OPT
100 R1083 R1084 100 100 R1104 R1100 100 100 R1077 100 R1101 100 R1102 R1078 100 100 OPT R1105 100 R1106
+3.3V_VDDP_ST
22 R1188 DQS0 DQM0 MDATA[0] MDATA[1] MDATA[2] MDATA[3] MDATA[4] MDATA[5] MDATA[6] MDATA[7] DQS1 DQM1 MDATA[8] MDATA[9] MDATA[10] MDATA[11] MDATA[12] MDATA[13] MDATA[14] MDATA[15]
R1019 2.7K
R1020 2.7K
R1009
BOOSTER 001:AD15 Flash_WP_2 EYEQ_RESET 010:P9 008:AK10 YAMAHA_GAIN0 008:AK10 PS421_RST 10K 008:AK11 YAMAHA_GAIN1 R1017 5V_MNT 009:J15 OPT SPI_CSN_2 001:W15 004:K16;004:L3;004:R8 SDA_A_TU SCL_A_TU
DDR MEMORY
C107 27pF
X100 12MHz 0
A2 A1 P4 N4 C7 Y15 W5 Y5 T13 B2 B1 C2 C1 D2 D1 E2 E1 G5 E3 E5 F5 E17 G1 G2 F3 F2 REFP F1 H1 H2 H3 J1 BIN1P_2 J2 J3 K1 K2 F4 K3 L1 J4 K4 L4 L2 Y1(CVBS5P) C0(CVBS6P) Y0(CVBS4P) L3 C1(CVBS7P) VSYNC0 HSYNC0 RIN0P RIN0M SOGIN0M GIN0P GIN0M
8 9
009:H14;009:K17 INV_CTL 007:R11;007:W23;007:AD24 5V_HDMI_4 003:M14;004:H13;001:AB5;001:AM5 SCL_D_TU 008:H22 AMP_RST 008:S16 MUTE SDA_D_TU 005:L18;008:E6;008:O10 COMP_SEL 008:AL9 MUTE_YAMAHA 010:E8 LED_G 004:J11TU_RESET_N PS421/NTP_SDA PS421/NTP_SCL 5V_HDMI_3 5V_HDMI_2 5V_HDMI_1 AC_DET DQS3 DQM3 MDATA[24] MDATA[25] MDATA[26] MDATA[27] MDATA[28] MDATA[29] MDATA[30] MDATA[31] M_CAS M_RAS M_WE BA0 BA1
100 0 0 100 22 100 100 22 100 100 22 100 100 100 100 100 100 100 100 100 100 22
R1066 R1087 R1089 R1090 R1091 R1092 R1088 R1067 R1068 R1069 R1070 R1093 R1094 R1071 R1095 R1072 R1073 R1074 R1096 R1097 R1075 R1103
0 0
1% 910
R1050
R1049
R1001 1K
IC101
R1010 10K
NC
VCC
010:H10 IR
SW100
TMUE312GAB 1 OPT 2
KIA7027AF 1 3
1A
2 HDMI
RXO0+ RXO1RXO1+
IC105 S25FL064A
GND
1Y
C111 0.1uF
FLASH MEMORY
R1158 R1154 R1155 R1156 R1157 R1153 R1149 R1150 R1151 R1152 R1145 R1146 R1147 R1148 R1141 R1142 R1143 R1144 56 56 56 1 56 56 56 56 56 56 56 56 56 56 56 56 56 56 56
IC100 LGE7363C-LF
+3.3V_VDDP_ST R1132 100 SPI_SCK
RXO2RXO2+
VCC 2 15 SI
007:AG23 HDMI_CLKHDMI_CLK+ HDMI_RX0HDMI_RX0+ HDMI_RX1007:AI23HDMI_RX1+ HDMI_RX2HDMI_RX2+ +3.3V_AVDD_DVI 007:AF24 HPD 009:AB11 007:AG24 HDMI_SDA HDMI_SCL HDMI_CEC 005:R16 DSUB_HSYNC DSUB_VSYNC
1/16W
SPI_SDI
AR103 22
1/16W
VSS_2 M10
NC_3 5 12 NC_6
EAN42961201
EAN42961201
10K
C1003
0.01uF NON_YAMAHA
NON_YAMAHA R1185
FRC
FRC
R1011 1K
A0 1 8 WP VCC
FRC
R1127 4.7K
R1128 4.7K
R1129 4.7K
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
P19 RXE0+ RXE1RXE1+ RXE2RXE2+ RXECRXEC+ RXE3RXE3+ RXE4RXE4+ TS1_CLK TS1_SYNC
Flash_Memory
AR104 P20 R19 R20 T19 T20 U19 U20 V19 V20 W19 W20 J16 H16 TS1_VLD TS1_D0 TS0_CLK H17 K18 Y7 W7 AR106 22 1/16W AR105 22 1/16W 22 1/16W
LVDS
DSUB_R VSS_5 VSS_6 VSS_7 VSS_8 VIDEO IN VSS_10 VSS_11 VSS_12 VSS_13 VSS_14 K8 J12
1 16 SI HOLD SCK
47
C141
0.047uF
COMP_Y VSS_9
R1037 R1038
47 470
C135
C136
0.047uF 1000pF
3216
R1039
COMP_Pr 005:M17
47
C137
0.047uF
47
MADR[12] MADR[11] MADR[10] MADR[9] MADR[8] MADR[7] MADR[6] MADR[5] MADR[4] MADR[3] MADR[2] MADR[1] MADR[0] LVB_0M LVB_0P LVB_1M LVB_1P LVB_2M LVB_2P LVB_CKM LVB_CKP LVB_3M LVB_3P LVB_4M LVB_4P LVA_0M LVA_0P LVA_1M LVA_1P LVA_2M LVA_2P LVA_CKM LVA_CKP LVA_3M LVA_3P LVA_4M LVA_4P
M1 G4 N3 M4 N2 G3 M2 N1 CVBS_OUT P1
4 13 NC_6
K9
R1004 0 2012
CVBS3P CVBS2P CVBS1P VCOM1 CVBS0P
V7 U7 T7 Y6 W6 V6 U6 TS0_D1 TS0_D0 PCM_A0 PCM_A1 PCM_A2 PCM_A3 PCM_A4 PCM_A5 PCM_A6 PCM_A7 PCM_A8 PCM_A9 PCM_A10 PCM_A11 PCM_A12 PCM_A13 PCM_A14 PCM_D0 PCM_D1 T5 T6 Y12 W12 V12 U12 Y11 W11 V11 U11 T11 Y10 W10 V10 U10 T10 Y9 V9 U9 PCM_D2 PCM_D3 PCM_D4 PCM_D5 PCM_D6 PCM_D7 PCM_IORD PCM_IOWR PCM_OE_N PCM_WE_N PCM_REG_N PCM_CE_N PCM_IRQA T9 Y8 W8 V8 U8 T8 P16 R16 M17 N17 T17 V18 P18 T18
J11
VCC 2 15
TV_CVBS+
VCOM0
R1025 R1026 R1027 R1028 R1029 R1030 R1031 R1032 R1033 R1034 VSS_18 J9
NC_2
C132 47 C133 47 C114 47 C115 47 C116 47 C117 47 C118 47 C119 47 C120 47 C121 VIDEO OUT VSS_19 VSS_20
NC_3 5 12
0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF 0.047uF C170 0.1uF +3.3V_VDDP_ST
NC_5
47
P2 R1 R2 R3 LINE_IN_1L LINE_IN_1R LINE_IN_2L LINE_IN_2R LINE_IN_3L LINE_IN_3R R4 T1 LINE_IN_0R LINE_IN_0L SIF_IN1M SIF_IN1P
R1051 J8 C3 D3
NC_4 6 11
AV_CVBS_OUT SIF+
R1023
R1024 H4 C8
SO
TU_TS_DATA[0]
TS SIGNAL
SPK_P
T2 T3
VSS_24 VSS_25 VSS_26 VSS_27 VSS_28 E9 C16 D16 C18 D18 E18 +3.3V_VDDP_ST T12 V16 W16 W17 W18 Y20
A0 1 A1 2 A2 3 VSS 4 5 SDA 6 SCL 7 WP 8 VCC IC109 CAT24WC08W-T
C9 D8 D9 E8
R1003
T4 R5 U3 U2 U1 V1 V2 W1 W2 Y1 Y2 W13 Y13 W14 Y14 U13 V13 U14 V14 G17 E15 D17 C17 G16 F16 F17 M3 W9 Y18 Y16 Y19 Y17 SPI_CZ1 SPI_DO1 SPI_DI1 SPI_CK1 NC_2 NC_1 I2S_IN_SD I2S_OUT_MCK I2S_OUT_WS I2S_OUT_BCK I2S_OUT_SD SPDIF_OUT SPDIF_IN PWM3 PWM2 PWM1 PWM0 SAR3 SAR2 SAR1 SAR0 LINE_OUT_0R(DACO_R) LINE_OUT_0L(DACO_L) LINE_OUT_1R(DACO_S) LINE_OUT_1L LINE_OUT_2R LINE_OUT_2L AUVAG AUVRP AUVRM VIM0
C122 C123 0 C124 C125 C126 C127 C128 C129 C130 C131
0.1uF 0.1uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF 2.2uF
22K C105 VSS_29 VSS_30 VSS_31 VSS_32 VSS_33 VSS_34 VSS_35 VSS_36 VSS_37
0.01uF
100
R1021
100
R1022
R1008
100 100
R1047 R1048
C104
R1007
0.01uF R1002
R1055 R1056
HDCP EEPROM
C171 0.1uF 22 R125 R126 22 SYSTEM_SDA 001:H28;001:S5 001:H28;001:S5 SYSTEM_SCL
008:C27
SPDIF_OUT
N16 K16
SCHEMATIC DIAGRAM
+5V_TU
EEPROM
+5V_ST +3.3V_VDDP_ST
I/0 EXPANSION-1
C1001 0.1uF C1002 47uF 16V
I/0 EXPANSION-2
FRC
//BOOTSTRAP PWM[1:0]=10
+3.3V_VDDP_ST
+3.3V_VDDP_ST
IC103 AT24C512W-10SI-2.7
+3.3V_CI
JLC1562BFEL
0 R1175
1 A0 VDD 16
001:G12;010:P10
001:G12;009:H14
R1057 R1082 R1111 3.3K 1K 0 OPT OPT R1118 100 R1119 100
2 A1
SDA 15
22
R1168
2 A1
SDA 15
FRC 22 OPT 0 R1176 22 100 006:H13 005:R9 SIDE_Y/C_DET 100 COMP1_DET R1137 100 005:G11 005:AB15 COMP2_DET DSUB_DET 100 R1134
6 D2 D6 11
R1182
R1016 1K
3 A2
SCL 14
FRC 22
52" Sharp
42"/47" FHD
32/37/42/47HD
26'HD
R1181 R1178
FRC_RESET EN_1.3PLL
+3.3V_CI
+2.5V_DDR +2.5V_DDR
1 mil = 0.0254 mm 20 mil = 0.508 mm 40 mil = 1.016 mm ADDRESS TOTAL LENGTH < 3000 mil (76.2mm)
C212 C217 C219 C213 C214 C216 C220
470pF
0.1uF
470pF
470pF
C202
470pF
C206
C207
0.1uF
C203
C204
C205
C208
0.1uF C222
470pF
0.1uF
470pF
470pF
470pF
0.1uF
0.1uF 50V
IC200
HY5DU561622FTP-4-C
IC201
HY5DU561622FTP-4-C
AR200 22 1/16W 66 1 2 3 4 5 6 7 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 24 NC_3 25 BA0 26 BA1 27 A10/AP 28 A0 29 A1 30 A2 31 A3 32 VDD_3 33 43 42 41 40 39 38 37 36 35 34 DQ8 NC_6 VSSQ_3 UDQS NC_5 VREF VSS_2 UDM /CLK CLK CKE 23 NC_4 A12 1% R219 22 1% R209 300 0 R221 0 R216 56 1% /CS R220 R210 56 1% VDDQ_4 DQ9 DQ10 VSSQ_4 DQ11 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 DQ12 AR207 22 61 VDDQ_5 62 DQ13 63 DQ14 AR206 22 64 VSSQ_5 65 DQ15 65 64 63 62 61 60 59 58 57 56 55 54 53 52 VSSQ_3 VDDQ_3 NC_6 NC_1 DQ8 DQ7 VDDQ_4 VSSQ_2 DQ9 DQ6 DQ10 DQ5 VSSQ_4 VDDQ_2 DQ11 AR203 22 1/16W DQ4 DQ12 AR205 22 1/16W DQ3 VDDQ_5 VSSQ_1 DQ13 DQ2 DQ14 DQ1 VSSQ_5 VDDQ_1 AR202 22 1/16W DQ15 DQ0 VSS_3 VDD_1 66 VSS_3
VDD_1
DQ0
AR204 22 1/16W
VDDQ_1
DQ1
DQ2
VSSQ_1
AR201 22 1/16W
DQ3
DQ4
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
MDATA[4] MDATA[5] MDATA[6] MDATA[7] MDATA[27] MDATA[26] MDATA[25] MDATA[24] MDATA[20] MDATA[21] MDATA[22] MDATA[23] +2.5V_DDR DQS0 DQS3
1% VDD_2 NC R203 22 LDM /WE /CAS 1% NC_2 1% VREF VSS_2 UDM /CLK 0 CLK 1% R204 300 1% R222 R201 22 C224 0.1uF 50V R206 1K 1% R207 1K R208 56 LDQS
VDDQ_2
DQ5
10
DQ6
11
VSSQ_2
12
DQ7
13
NC_1
14
VDDQ_3 51 50 49 48 47 46 45 44 43 42 A12 NC_4 56 R213 CKE 0 R223 /RAS NC_5 1% UDQS R205 56
15
DQS2
DDR1 & DDR2 different length range = +/- 25 mil (max +/- 50 mil)
0.1uF C223
+2.5V_DDR
R212 1K 1% R211 1K 1%
R202 56
LDQS
DQS1
16
1%
NC_2
17
VDD_2
18
NC
19
R200 22
LDM
20
1%
/WE
21
/CAS
M_CAS
22
/RAS
M_RAS
23
/CS
24
NC_3 41
25
BA0
26
MADR[11] MADR[9]
A8
MADR[11]
A9
BA1 39
BA1 MADR[8]
A7 38
27
MADR[9]
A8
A10/AP
MADR[10] MADR[7]
A6 37
28
MADR[8]
A7
A0
MADR[0] MADR[6]
A5 36
29
MADR[7]
A6
A1
MADR[1] MADR[5]
A4 35
30
MADR[6]
A5
A2
MADR[2] MADR[4]
VSS_1 34
31
MADR[5]
A4
A3
MADR[3]
32
MADR[4]
VSS_1
VDD_3
33
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
DDR
003:T8;009:K5 PANEL_POWER
P302
C301 0.1uF 50V R310 1.3K R311 1.3K R312 R313 1.3K 1.3K
SMAW200-26C
L301
FRC
+5V_GENERAL
L302
FRC
6 6 7 R314 0 OPT JP3006 R316 0 FRC SCL_D_TU 6 JP3005 7 LVA_4P LVA_4M 8 LVA_3P LVA_3M LVA_CKP LVA_CKM LVA_2P 11 LVA_2M LVA_1P 20 20 LVA_1M 13 LVA_0P 22 22 LVA_0M R317 0 FRAME_SEL R301 0 FRC FRC_RESET NON-FRC R302 0 OPT 0 HD 27 LVB_4P +3.3V_CI FHD&NON-FRC 0 R305 BIT_SEL OPT +3.3V_CI LVB_4M LVB_3P LVB_3M 0 0 LVB_CKP OPT LVB_CKM LVB_2P LVB_2M LVB_1P LVB_1M OPT 37 LVB_0P LVB_0M 38 39 OPT 40 OPT OPT R1190 R1192 0 R1189 4.7K R307 28 29 30 31 32 33 34 35 36 R303 +3.3V_CI R306 4.7K OPT LVDS_SEL R304 0 OPT 23 24 25 26 23 24 25 26 21 21 12 10 9 OPT R315 0 FRC SDA_D_TU 5 8 8 9 10 11 12 13 14 15 JP3001 16 17 18 19 9 10 11 12 13 14 15 16 17 18 19 7
+3.3V_VDDP_ST
L303 L304
FRC
+12V +15V
JP3002
JP3003
003:L19;009:K5 PANEL_POWER
+3.3V_CI
OPT
R308 0 R309 0
PANEL_POWER DEVIDER
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
MODUEL&CTL
R1191 0
JP3004
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
EN_2.5VF EN_1.3VF EN_3.3VF EN_1.8VF EN_1.3PLL
+5V_TU
AUS_Tuner
TU401 TDFV-G135D1
Q405 R444 OPT B C C Q407 2SC3052 BOOSTER E C426 0.01uF 50V C427 100uF 16V R469 0 B R467 0 R455 10K TAIWAN E 2SA1530A-T112-1R R450 2.2K
ANT[5V]
BB[CTR]
C434 0.1uF
TP470
GND_1
+B[5V]
NC_1
RF_AGC
R402 0
7 +5V_TU R478 SDA_A_TU 004:L3;004:R8;001:H26 R479 SDA_A_TU_5V SCL_A_TU 004:L4;004:R8;001:H26 R457 SCL_A_TU_5V TV_CVBS+ R454 0 OPT R424 4.7K +5V_TU E R465 330 R466 330 2SA1530A-T112-1R B Q404 R451 C OPT R468 0 220 R453 270 AUS R453-*1 220 TAIWAN R480 OPT R481 0 AUS_ONLY 0 TP466 C429 0.01uF 50V 0 AUS_ONLY 0 OPT TP465
TP[VT]
OPT
OPT
NC_2
C435 0.1uF
R419
47
GND_2
AUS_ONLY
10
SDA_T
AUS_ONLY
11
SCL_T
R420
47
12
AIF_1
AUS_ONLY
13
AIF_2
AUS_ONLY
14
NC_3
EBL35311216
15
VIDEO
R401 0 AUS_ONLY
EBL42367001
R475 2K
R474 2K
R418 4.7K G
R476 5.6K
R477 5.6K
LD400
ANT[5V]
BB[CTR]
GND_1
+B[5V]
NC_1
RF_AGC
TP[VT]
NC_2
GND_2
SDA_T
SCL_T
AIF_1
AIF_2
NC_3
NC_4
NC_5
NC_6
SDA
SCL
RST
3.3V
1.8V
ERR
MCL
D7
D6
D5
D4
D3
D2
D1
D0
VAL
SYNC
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
TU401-*1 TDFV-D135F
34
SHIELD
R471 SDA_A_TU
0 S 2N7002(F) Q409 D SDA_A_TU_5V GND_4 GND GND_3 GND GND_2 GND GND_1 GND
TAIWAN_TUNER
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
TUNER
35
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
SDA_D_TU 003:M14;001:H25;001:AB6;001:AM6 SCL_D_TU +5V_TU R461 100 2SA1530A-T112-1R B Q406 C TAIWAN B +3.3V_TU E AM_AUDIO R445 1K TAIWAN R463 0 C428 4700pF 50V R448 1K R462 0 Q402 2SC3052 C E R423 1.2K 003:M14;001:H25;001:AB5;001:AM5 +3.3V_TU TU_TS_CLK R429 100 TU_RESET_N R434 4.7K C425 4700pF 50V C422 0.1uF 50V OPT +5V_TU C433 0.1uF 16V TAIWAN 100pF R464 50V TU_TS_DATA[0] TU_TS_VAL E R482 R483 SDA_A_TU_5V R484 SCL_A_TU 004:K15;004:L4;001:H26 SCL_A_TU_5V R485 0 OPT 0 TAIWAN TU_TS_SYNC B R443 4.7K Q403 C 2SA1530A-T112-1R 004:K16;004:L3;001:H26 SDA_A_TU SIF+ R446 470 R449 82 OPT 0 OPT 0 TAIWAN TAIWAN OPT
16
AUDIO
R403 0 AUS_ONLY
17
SIF
C403
AUS_ONLY
18
SDA
100pF
50V
R416 33
19
SCL
20
RST
R417 33
21
3.3V
R421 1.2K
22
1.8V
23
ERR
24
MCL
R404
100
TU_TS_CLK
25
D7
26
D6
27
D5
28
D4
29
D3
30
D2
31
D1
32
D0
R412
100
TU_TS_DATA[0]
+5V_TU
33
VAL
R413
100
TU_TS_VAL
34
SYNC
R414
100
TU_TS_SYNC
R456 4.7K
R458 4.7K
TAIWAN
35
+3.3V_TU
NC_1 1 GND_1 2 +B[5V] 3 NC_2 4 RF_AGC 5 TP[33V_OPTION] 6 NC_3 7 GND_2 8 DATA 9 CLOCK 10 AS 11 NC_4 12 V-OUT 13 AFT 14 A-OUT 15 SIF-OUT 16 NC_5 17 NC_6 18 NC_7 19 NC_8 20
C432 27pF
TAIWAN
SHIELD
21 SHIELD
+1.8V_TU
+3.3V_TU
+5V_TU
+3.3V_TU
0 0 0
0 0 0
0 0 0
0 0 0
33
2N7002(F) Q408
R428
R433
R438
R442
+5V_ST
D-SUB
D519 ENKMC2838-T112 A1 C A2
IC501 AT24C02BN-10SU-1.8
COMPONENT-SW
TP551 16 JP5021 EEPROM_WP 100 R7017 DDC_SCL/UART_RX DDC_SDA/UART_TX 100 R7018 R553 R556 10K 100 C506 VCC
A0 1 8 WP VCC
IC500 STMAV340
L501 +5V_GENERAL MBW3216-501TF
A1 2 7 SCL
R502 0
1B
005:T6 COMP1_Pb
HIGH:COMP1
GND 0IMMRAL014D
1C
005:J8 COMP2_Pb
LOW :COMP2
3 6 SDA 4 5
A2
R504 0 14 COMP_SEL 008:E6;008:O10;001:H24 R549 10K C519 18pF 50V C520 18pF 50V R552 22 R554 22 COMP_Pb D513 30V JP5013 OPT +5V_GENERAL JP5014 R541 100 R543 22 GND R548 75 JP5015 R555 0 OPT OPT JP5016 D516 CDS3C30GTH 30V
11 12 13 14 15
2B R522 22
005:T6 COMP1_Pr 1A R523 001:F18 D514 30V CDS3C30GTH D520 CDS3C05GTA 5.6V D518 CDS3C05GTA 5.6V OPT 22 C513 22pF 50V R540 100 DSUB_VSYNC 11 COMP_Y 001:F18 DSUB_HSYNC 4A DSUB_B C515 OPT JP5017 D515 CDS3C30GTH 30V OPT 3A R525 22
2C
005:J7 COMP2_Pr
R506 0 12
3B
R507 0
3C
005:J9
COMP2_Y
4B 10
4C 9
EAN32724702
005:T7
COMP1_Y
10
P501 KCN-DS-1-0089
R547 75
+5V_GENERAL
COMPONENT2
COMP2_DET 001:W4
R501 10K
R508 1K
JK501
PPJ209-02 +5V_GENERAL
2A
[GN]1P_CAN
4A R515 22 COMP2_Y COMP1_DET JK502 R516 22 PPJ209-02 COMP2_Pb 2A 4A 3A 2B 5B 2C 5C COMP2_R_IN 2D 5D 2E 4E 3E [RD]1P_CAN2 [RD]CONTACT [RD]O_SPRING [WH]C_LUG_L R531 470K C511 100pF 50V R536 10K [WH]1P_CAN R521 12K [RD]C_LUG_L D509 CDS3C30GTH 30V OPT R530 75 [RD]1P_CAN1 [BL]C_LUG_L R529 75 [BL]1P_CAN R528 75 [GN]O_SPRING [GN]CONTACT C508 0.1uF 50V C509 0.1uF 50V C510 0.1uF 50V R537 10K R535 22 R534 22 R533 22 [GN]1P_CAN D512 CDS3C05GTA 5.6V OPT R526 10K R527 1K
[GN]CONTACT
3A
[GN]O_SPRING
C501
COMPONENT1
2B
[BL]1P_CAN
R509 75
0.1uF 50V
001:W4
5B
[BL]C_LUG_L
C502
6612J10031A
2C R517 22 COMP2_Pr
[RD]1P_CAN1
R510 75
0.1uF 50V
5C
[RD]C_LUG_L
C503
[WH]C_LUG_L
R519 10K
6612J10031A
[WH]1P_CAN
R511 75
0.1uF 50V
COMP1_Y
2E
[RD]1P_CAN2
4E R518 10K
[RD]CONTACT
R513 470K
COMP1_Pb
3E
[RD]O_SPRING
COMP1_Pr
COMP1_R_IN D511 CDS3C05GTA R532 5.6V 470K OPT C512 100pF 50V R539 12K
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
16
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
JP5020
+3.3V_VDDP_ST
JK603 PEJ024-01
RS232C
L606 C612 0.1uF 50V +5V_USB C613 0.1uF 50V R635 51K C616 0.1uF 50V JP6020 C622 10uF 16V
USB
6A
T_TERMINAL1
7A
B_TERMINAL1
PC_R_IN
001:G15
R_SPRING
OPT
5 6 5 4 3 2 8 7 1
TP619
T_SPRING
R603 470K
R615 5.1K
PC_L_IN IC601
TP620
6B MAX3232CDR EAN41348201
TP621
T_TERMINAL2 +5V_USB
OC1
R608 470K
R616 5.1K
OPT
11
12
13
14
10
15
16
KJA-UB-4-0004 P602
SHIELD_PLATE
JP6022
7B 1
B_TERMINAL2
R613 10K
MBW3216-501TF
E_SPRING
GND
DIN2
DIN1
RIN1
VCC
ROUT2
ROUT1
DOUT1
C617 0.47uF 25V OPT 001:AB4 USB_OCD OPT JP6017 006:AE16;006:AI12 +12V_AVOUT C621 0.1uF 50V E R632 470 +12V 006:X19;006:AI12 R633 47K C AV_CVBS_OUT B C620 47uF 16V L610 HH-1M3216-501 +12V_AVOUT +12V_AVOUT 2SA1530A-T112-1R B Q601 003:Z14;008:Z12;009:A8;009:F12;009:H19 Q602 JK604 2SC3875S C614 100uF 16V R630 680 E R634 15K R631 220 AUS C629 100uF 16V PPJ204-01 C630 0.1uF 50V R631-*1 200 TAIWAN 006:X19;006:AE16 +12V_AVOUT
TP660
R623 4.7K R626 100 R651 100K R628 100 R629 0 JP6021
R624 4.7K D610 CDS3C30GTH 30V OPT D611 CDS3C30GTH 30V C609 220pF 50V P601 KCN-DS-1-0088 6 7 8 9 C611 220pF 50V
Side AV
R620 0
SIDE_CVBS_IN
JK601
PPJ218-01 10
+5V_GENERAL
D609 30V
R619 75
4A
[YL]O_SPRING
R602 10K 1 2 3 4 5
L603
5A
[YL]CONTACT
SIDE_CVBS_DET
R614 22
2A
[YL]U_CAN
ZD603 5.6B
ZD606
3B
[WH]C_LUG
5.6B
L602
R618 10K
SIDE_L_IN
2B
[WH]U_CAN
ZD604 5.6B
ZD607
R605 470K
4C
[RD]O_SPRING
R622 12K
2K
JK606
JP6019
PPJ200-07 5B 2B 4A
JP6018
R648
470pF
470pF
OPT
C618
ZD601
OPT ZD602
C619
C L608 BG2012B080TF
R637 1.5K D614 5.6V OPT C623 1000pF 50V C624 4.7uF 35V
TP666
Q605 2SC3875S
TP667
2SA1530A-T112-1R Q603 B
C Q608 2SC3875S E B
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
R649
TP665
2K
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
AV-OUT-CVBS
Monitor Out - CVBS
C 1 O_SPRING R627 75 2 OPT 0 3 U_CAN 16V CONTACT R625 C615 100uF EAG35542201 C627 0.1uF 16V E 2SA1530A-T112-1R B Q604 C L609 BG2012B080TF C628 4.7uF 35V Q606 2SC3875S R638 1.5K C625 1000pF 50V D615 5.6V OPT E R642 560 R641 1K R646 47K C C632 B 10uF R647 15K C635 OPT AV_L_OUT
5.6B
L601
R617
10K
5C
[RD]CONTACT
SIDE_R_IN
ZD605 5.6B
ZD608
2C
[RD]U_CAN
R604 470K
R621 12K
5.6B
EAG42205801
JK602 PSJ018-01
GND_TER
C_LUG_S1
C_LUG_L1
SIDE_Y_IN
R609
22
C_LUG_S2
R606 75
OPT
C_LUG_L2
R611 22
SIDE_C_IN
EAG42206001
NC1
R607 75
OPT
COM1
NO1
11
NO2
10
COM2
R610 1K
NC2
SIDE_Y/C_DET
12
+5V_GENERAL
SHIELD
R601 10K
AV-OUT-AUDIO
R650
PC-AUDIO
+3.3V_VDDP_ST
001:H27 MUTE_AV_L/R
3A 2A
TP664
R639 1K
R643 47K
+3.3V_VDDP_ST
R718
R725 47K
C OPT IC702 A2 ENKMC2838-T112 D706 1 WP R760 10K 007:H17;007:AJ9 DDC_SCL_2 0 8 OPT A0 VCC C 0 R7009 5V_HDMI_1 R7010 DDC_SDA_2 R756 22 OPT C714 +5V_ST AT24C02BN-10SU-1.8 A1
OPT
22 OPT IC701 A2 AT24C02BN-10SU-1.8 ENKMC2838-T112 D702 A0 1 WP 3 6 SDA R754 22 OPT OPT 10K GND 4 5 DDC_SCL_1 A2 3 0.1uF C709 0.1uF C710 0.1uF C711 0.1uF C712 0.1uF C713 0.1uF SDA R732 22 OPT DDC_SDA_1 5V_HDMI_1 HPD1 R733 22 OPT 6 SCL JP7007 R735 10K R739 R729 0 C705 0.1uF A2 SCL 8 2 7 VCC C A1 A1
Q702 2SC3052
HPD1
18
R702
17
3.6K
R705 1K
JP7003
R712
16 A1 2 7
DDC_SDA_1
15
R713
DDC_SCL_1
EEPROM_WP
19
1K R724
JP7004
14
R710
13
CEC_REMOTE
12 GND 4 5
CK-_HDMI1
11 10
CK+
CK+_HDMI1
DDC_SDA_1
EAG39789401
D0-_HDMI1
DDC_SCL_4
7 R777 5V_HDMI_4 +5V_ST R778 R7007 36K 3.3K OPT A2 A1 R7008 0 R763 R764 0 0 0 0 0 OPT 0 0 0 36K 3.3K OPT
D0+
D0+_HDMI1
D1-
D1-_HDMI1
D1_GND
HDMI_CLK-
HDMI_CLK+
HDMI_RX0+
HDMI_RX1-
HDMI_RX0-
HDMI_RX1+
HDMI_RX2-
D1+_HDMI1 5V_HDMI_3 +5V_ST AT24C02BN-10SU-1.8 A2 A1 ENKMC2838-T112 D705 A0 1 WP 0 0 R779 R780 R768 R770 10K R798 R7001 007:V9;007:AE24 DDC_SCL_4 R772 R774 R781 0 R759 8 VCC C ENKMC2838-T112 D701 A0 1 A1 C704 0.1uF R736 10K 3 6 SDA DDC_SDA_4 SCL2 SDA2 HPD2 POW2 VCC_7 GND_9 VCC_6 R755 22 OPT DDC_SDA_3 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 GND_10 GND_8 R753 22 OPT POW_SINK HPD_SINK SDA_SINK SCL_SINK OUT_D1N OUT_D1P OUT_D2N OUT_D2P OUT_D3N OUT_D3P OUT_D4N OUT_D4P POW3 DDC_SCL_3 GND 4 5 A2 SCL R734 10K 2 7 WP R728 0 8 VCC C OPT IC703 EEPROM_WP AT24C02BN-10SU-1.8 OPT IC704
D2_GND
EEPROM_WP
D2-
D2-_HDMI1
HDMI_RX2+
D1+
DDC_SDA_4
HDMI_SDA
HDMI_SCL
D0_GND
DDC_SCL_1
D0-
EEPROM_WP
R720 1K
D2+
C716 0.1uF C719 0.1uF C718 0.1uF C717 0.1uF HPD3 SDA3 SCL3 C720 0.1uF 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 92 93 94 95 96 IN1D3P VCC_11 D2-_HDMI3 D2+_HDMI3 IN1D4N IN1D4P GND_15 97 98 99 100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 33 32 31 30 29 28 27 26
D2+_HDMI1
20
GND
JK701
UI_HW_PORT1
A2 3 6
GND
+3.3V_VDDP_ST
001:H23;007:W29;007:AM11 5V_HDMI_2 GND_11 GND IN2D1N IN2D1P VCC_8 D0-_HDMI4 D0+_HDMI4 IN2D2N IN2D2P GND_12 D1-_HDMI4 D1+_HDMI4 IN2D3N IN2D3P VCC_9 R737 IN2D4N IN2D4P GND_13 CK-_HDMI3 R740 0 OPT 001:J20;007:AF11 HDMI_CEC IN1D2P GND_14 D1-_HDMI3 D1+_HDMI3 IN1D3N D0-_HDMI3 D0+_HDMI3 IN1D2N VCC_10 91 CK+_HDMI3 IN1D1P 90 IN1D1N 89 88 87 68K 27K A R743 D2+_HDMI4 D2-_HDMI4 86 85 84 83 82 81 80 79 78 77 CK+_HDMI4 CK-_HDMI4 76
R719
R727 47K
GND_7 IN3D4P IN3D4N VCC_5 IN3D3P IN3D3N GND_6 IN3D2P IN3D2N VCC_4 IN3D1P IN3D1N GND_5 IN4D4P IN4D4N VCC_3 IN4D3P IN4D3N GND_4 IN4D2P IN4D2N VCC_2 IN4D1P IN4D1N GND_3
OPT
18
R704
17
3.6K
R706 1K
JP7005
R714
1K R726
OPT
13 0 CEC_REMOTE 007:F8;007:F26;007:F17;007:T8
IC705 PS421
R711 R738
11 10
CK+
MMBD301LT1G
EAG39789401
SCL1
SDA1
GPD1
POW1
CEXT
TEST
REXT
POW4
HPD4
SDA4
GND_1
VCC_1
ECE_IN
DDCBUF_EN
S1/SDA_CTL
S2/SCL_CTL
OE#/POWDN
R769
R771
20
R773
D2+_HDMI2
R797
4.7K
D2+
5V_HDMI_3
PC1/I2C_ADDR1
S3/I2C_ADDR0
PC0/I2C_RST
D2_GND
I2C_CTL_EN
D2-
D2-_HDMI2
CEC_OUT
D1+_HDMI2
GND_2
OPT
R786 0
OPT R788 0
510 R795
21
C715
R799
R7002
OPT
2.2uF
UI_HW_PORT2
R761 OPT 4.7K +3.3V_VDDP_ST R762 OPT 4.7K 5V_HDMI_4 R747 0 R752 47K R748 1K HPD4 C JACK_GND B 20 E 19 HPD 3.6K +5V_POWER DDC/CEC_GND DDC_SDA_4 SDA DDC_SCL_4 SCL JP7009 R744 0 CEC_REMOTE CEC CK-_HDMI4 CLKSDA_EYEQ/AMP CLK_SHIELD CK+_HDMI4 CLK+ DATA0DATA0_SHIELD DATA0+ DATA1DATA1_SHIELD DATA1+ DATA2DATA2_SHIELD DATA2+ D2+_HDMI4 D1+_HDMI4 D2-_HDMI4 D0+_HDMI4 D1-_HDMI4 D0-_HDMI4 SCL_EYEQ/AMP OPT NC R746 0 JP7010 R745 0 R742 1K 18 R741 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C706 0.1uF 50V Q704 2SC3052 1K R751 OPT R767 OPT 4.7K
R775
GND
R789
JK702
OPT
R7004
GND
SCL4
D1+
CEC
+3.3V_VDDP_ST
22
HPD3 007:AF11
DDC_SCL_3
19
DDC_SDA_3
HDMI_CEC
R7021 0
Q701 2SC3052
HPD3
OPT
R717 1K
0 R787 OPT
3.6K
18
R701
R782
15
DDC_SCL_3
DDC_SDA_2
14
R709
EAG42025501
12
R793
11 10
CK+
CK+_HDMI3
D0-
D0-_HDMI3
EAG39789401
D0_GND
R790 0
D1-
D1-_HDMI3
D1_GND
D1+
D1+_HDMI3
D2-
D2-_HDMI3
2.7K
R7019
20
GND
21
GND
UI_HW_PORT4
PS421/NTP_SCL
UI_HW_PORT3
JK703
GND
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
HDMI
R7020
D2+
2.7K
D2_GND
R791 0 R792 0
D0+
D0+_HDMI3
R796 OPT
4.7K
13
DDC_SCL_2
JP7001
R707
HPD2
16
DDC_SDA_3
R776
R785 0
R7011
17
JP7002 R708
OPT
R703 1K
4.7K
1K R722
PS421_RST
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
+3.3V_VDDP_ST
D2+_HDMI2 D2-_HDMI2 D1+_HDMI2 D1-_HDMI2 D0+_HDMI2 D0-_HDMI2 CK+_HDMI2 CK-_HDMI2
22
Q703 2SC3052
R721 1K
HPD2
19
16
DDC_SDA_2
15
R715
DDC_SCL_2
JP7006
14
12
CK-_HDMI2
S BSS83 Q705 G
D0-
D0-_HDMI2
D0_GND
D0+
D0+_HDMI2
D1-
D1-_HDMI2
D1_GND
SIDE HDMI
5V_HDMI_2
001:H24;007:O23;007:AD13 5V_HDMI_3
R716
OPT
R723 47K
R7006
JP8002
R801 1K
JP8003
JK801
SPDIF_OUT C819 330uF 25V C830 OPT 1000pF 50V R824 OPT 5.6 D802 1N4148W SPK_L+ C851 0.01uF 50V R838 3.3 SMAW250-04 P801 JP8005 R828 100V 5.6 C834 1000pF 50V 1S 1F L806 120-ohm SPK_RL807 120-ohm SPK_LC820 22000pF 50V D801 1N4148W +15V_AMP 100V D803 1N4148W SPK_L+ C832 OPT 1000pF 50V JP8006 100V 56 55 54 53 52 51 50 49 48 47 46 45 44 43 R826 OPT 5.6 SPK_R+ R830 C853 C839 0.47uF 50V C844 0.1uF 50V 3.3 R841 C845 R837 4.7K SPK_RC854 0.01uF 50V 0.1uF 50V 3.3 4.7K R836 0.01uF 50V R840 +15V_AMP 5.6 2S L808 120-ohm C821 1uF 16V SPK_L3 L809 120-ohm SPK_R+ 2 1 JP8007 C838 0.47uF 50V C842 0.1uF 50V 4.7K R834 +15V_AMP 2S
JP8004
JST1223-001
JP8001
OPT
Fiber Optic
VINPUT
VCC
GND
SPEAKER_L
R839 C843 0.1uF 50V R835 4.7K C852 0.01uF 50V 3.3
R819 3.3 C822 0.1uF 50V C824 0.1uF 50V C827 0.1uF 50V R825 OPT 5.6 R829 5.6 C835 1000pF 50V C817 0.01uF 50V C816 22000pF 50V
100
PGND1A_2 OUT1A_2
PGND1A_1 OUT1A_1
PVDD1A_2
PVDD1A_1
PVDD1B_2 OUT1B_2
PVDD1B_1 OUT1B_1
PGND1B_2
C809 1000pF 50V C814 +3.3V_CI AD 4 5 6 7 8 9 10 11 NTP3000A 31 30 29 15 16 17 18 19 20 21 22 23 24 25 26 27 28 R_SOUND_N +15V_AMP R_SOUND_P PGND2B_2 OUT2B_1 OUT2B_2 5.6 12 13 14 32 PVDD2B_1 5.6 R831 33 R827 OPT PVDD2B_2 EAN41584001 34 PVDD2A_1 C837 1000pF 50V 1S 1F 35 PVDD2A_2 36 OUT2A_1 IC802 37 OUT2A_2 C836 1000pF 50V 38 PGND2A_1 39 VSS_IO CLK_I CLK_O VDD_IO DGNDPLL C811 0.1uF 50V AGNDPLL LFM AVDDPLL DVDDPLL NC_1 C810 1000pF 50V R809 3.3K C833 OPT 1000pF 50V PGND2A_2 50V L805 DA-8580 EAP38319001 2F 1uF 3 40 BST2A VDR1A 10V /RESET 2 41 C826 22000pF VDR2A BST1A 1 42 NC_2 C825 16V1uF
PGND1B_1
AMP_RST JP8008
AUDIO_MASTER_CLK
+1.8V_AMP
OPT
R859 0
+1.8V_AMP
+1.8V_AMP
C807
SPEAKER_R
WCK
BCK
SDA
DVSS
DVDD
SDATA
FAULT
VDR2B
PROTECT
BST2B
PGND2B_1
+1.8V_AMP
SCL
PWM_3B/PWM_HP2
PWM_3A/PWM_HP1
L_SOUND_P
AMP
R846 0 +15V YAMAHA L810 +12V P_+16V_AMP_IN L811 OPT PVDDPL OUTPL_2 P_+16V_AMP_IN P_+16V_AMP_IN 1uF 25V
L_SOUND_N
YAMAHA
YAMAHA
GND
R849 0
100 OPT
OUTPL_1
PVSSL
OUTML_2
OUTML_1
32
31
30
29
28
27
26
GND C846 0.1uFYAMAHA C847 YAMAHA C841 1uF 25V C840 YAMAHA R833 10K YAMAHA 1uF 25V C848 0.1uFYAMAHA 1uF YAMAHA PVDDREG AVDD INLP INLM VREF INRM INRP AVSS COMP2_R_IN YD C813 R816 680K 2.2uF 50V R842 YAMAHA1% GND 68K R843 YAMAHA1% 1K PLIMIT R818 10K R817 +5V_GENERAL 14 CONTROL_A VCC SPK_N SPK_P COMP_SEL 0 1 2 3 4 5 6 7 8 9
25 24 YAMAHA 23
R854
+5V_GENERAL
R852
AUDIO SWITCH
R832 10K
PVDDML
100 OPT
COMP1_L_IN
11
YAMAHA YAMAHA
10
11
12
13
14
15
C803 2.2uF R806 680K 50V 10 YC COMP_R +5V_GENERAL 8 R814 680K COMP1_R_IN C812 R813 680K 2.2uF 50V XC
CONTROL_B
16
YAMAHA
PVDDPR
OUTPR_1
OUTPR_2
OUTMR_1
0 C
R804
GND
OUTMR_2
R803 10K
PVDDMR
6 9
PVSSR
CONTROL_C
GND
R861 1K
YAMAHA
R847
YAMAHA
R_SOUND_P
R848
SPK R
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
AMP
R_SOUND_N
YAMAHA
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
C828 C829 0.1uF 50V 0.1uF 50V C823 22000pF 50V D804 1N4148W 100V AC_DET 001:H23;009:E15 R810 +15V_AMP R822 MUTE 0 GAIN[1:0] L,L R821 1.1K Gain 34dB L,H 40dB H,L 46dB H,H 28dB 001:H25 R820 120K OPT R862 R863 100 100 0 OPT R811 OPT 100 100 OPT R823 C815 0.1uF 50V C818 1uF 10V
MLB-201209-0120P-N2
R860 0
L801
L802
100pF 50V
MS_LRCH
MS_LRCK
MS_SCK
SPK L
MUTEN
HP
Output
Speaker
Mute
+5V_GENERAL
IC801 MC74HC4066ADR2G
R812 680K
XA
COMP2_L_IN
IC803 YDA148-EZ
R844 120K 1%
22 21 20 19 R845 100K 1% 18 17
NCDRC0 CKIN CKOUT MUTEN PROTN SLEEPN R850 68K YAMAHA R851 200K R853
YA
R855 0 YAMAHA R856 0 YAMAHA R857 0 YAMAHA GND 0 YAMAHA P_+16V_AMP_IN MUTE_YAMAHA
COMP_L 12 XD
+5V_GENERAL
YB
R805 680K
XB
+5V_GENERAL
R802 10K
COMP_SEL
1uF 25V
1uF 25V
GND
Q800 2SC3052
Stand-by +3.3V_+1.25V_MST_Core
+3.3V_AVDD +3.3V_VDDP_ST +5V_ST IC904 AZ1085S-3.3TR/E1 JP9010 INPUT 3 1 ADJ/GND L914 MBW3216-501TF +3.3V_AVDD_AU L918 MBW3216-501TF C937 330uF 16V C939 0.1uF 50V +1.25V_ST +1.25V_AVDD_DVI 0.01uF 50V +3.3V_IR +5V_GENERAL R922 0 L912 MBW3216-501TF C955 0.1uF 50V C957 0.1uF 50V L919 MBW3216-501TF C964 0.01uF 50V +1.25V_VDDC C938 100uF 16V C940 0.1uF 50V R921 0 L913 MBW3216-501TF +3.3V_AVDD_OTG C969 0.1uF 50V +3.3V_VDDP_ST IC903 +1.25V_ST AZ1085S-ADJTR/E1 INPUT 3 1 ADJ/GND C931 100uF 16V C934 0.1uF 50V R919 51 5% NON_52"Sharp 4.7K R916 V0 = 1.25(1+R2/R1) 5V_MNT 001:H26 +3.3V_VDDP_ST IC905 +3.3V_VDDP_ST +3.3V_CI L907 MBW3216-501TF +3.3V_AVDD_ADC L910 MBW3216-501TF L915 MBW3216-501TF C967 0.1uF 50V C962 0.01uF 50V +5V AZ1117D-3.3TRE1 INPUT 3 1 ADJ/GND L908 MBW3216-501TF C952 0.1uF 50V C941 100uF 16V C943 0.1uF 50V C951 0.1uF 50V 2 OUTPUT +3.3V_TU C992 0.01uF 50V R2 C965 0.01uF 50V C970 0.1uF 50V L921 MBW3216-501TF +3.3V_HDMI_ST 1/4W 5% C949 0.01uF 50V C954 0.1uF 50V C956 10uF 16V 3216 2 INV_CTL OUTPUT C984 0.01uF 50V 1/4W 5% C953 0.01uF 50V R917 10K C B R915 10K Q901 2SC3052 E 001:H25;009:H14 R918 10K OPT R920 3.3K 1% R1 R914 10K R913 100 C983 +3.3V_AVDD_MPLL 2 OUTPUT C963 0.01uF 50V 0.01uF 50V C982 C968 0.1uF 50V C987 0.1uF 50V +3.3V_VDDP_ST L911 MBW3216-501TF L917 MBW3216-501TF +3.3V_VDDP +3.3V_AVDD_SIF
P902
SMAW200-24C
L902 CB4532UK121E
+15V
2 C920 1uF 25V +12V C930 100uF 16V C933 0.1uF 50V JP9011 C923 0.1uF 16V +5V_GENERAL C966 0.01uF 50V C971 0.1uF 50V C988 0.1uF 50V
L903
JP902
+5V_ST
L901 CB4532UK121E
+3.3V_AVDD_LPLL
JP9008
10
JP901
11
13
JP9002
14
JP9005
12
JP9009
15
16
R911 0
RL_ON 001:B27;009:B5
17
18
AC_DET
JP9004
19
008:S16;001:H23
JP9012
R928
C925 0 52"Sharp
24
JP9001
23
JP9006
+5V_GENERAL C922
R923
L909 MBW3216-501TF
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
+3.3V_AVDD_MEMPLL IC907 +1.8V_TU C978 0.01uF 50V C985 0.1uF 50V
21
R929
22
R901
PWM_DIM 001:G12
DC-DC CONVERTER
IC902 KIA7805AF
INPUT 3 1 ADJ/GND 2 OUTPUT L906 MBW3216-501TF I 1 2 C C908 47uF 16V 3 O AZ1117D-1.8TRE1
003:Z14;006:AB17;008:Z12;009:A8;009:H19 +12V
+3.3V_MST
+3.3V_VDDP_ST L916 MBW3216-501TF IC909 +5V AZ1117D-3.3TRE1 INPUT OUTPUT 3 1 C960 100uF 16V C961 0.1uF 50V ADJ/GND 2 C973 100uF 16V C975 0.1uF 50V C981 0.01uF 50V C986 0.1uF 50V +3.3V_AVDD +3.3V_AVDD_DVI
+2.5V_DDR
006:AG26;008:D28;008:E28;009:M14;009:V11;009:Y8 +5V +5V IC910 AZ1117D-2.5TRE1 INPUT OUTPUT 3 1 C972 0.1uF 50V IC908 AZ1117D-1.8TRE1 +1.8V_AMP C932 0.1uF 50V INPUT 3 1 ADJ/GND C945 0.1uF 50V C958 100uF 16V C959 0.1uF 50V +2.5V +2.5V_DDR R924 0 3216 PANEL_POWER C921 OPT 0.1uF 50V 2 OUTPUT C928 100uF 16V C924 100uF 16V ADJ/GND R927 C974 10uF 16V R926 0 OPT C990 100uF 16V C991 0.1uF 50V 2 +2.5V
+12V
L904 MBW3216-501TF
+5V_ST
+5V_ST
S1 1
OPT C916
G1 7 D1_1 2
R905 10K
S2 3 6 D2_2
10uF
R906
G2 4 5 D2_1
560
Q902 2SC3052
RL_ON
R902 10K
001:B27;009:E16
R907 22K
R909 47K
TUNER_CI +3.3V_+1.8V_+1.5V
R910 47K
+2.5V_VDD_DDR
Q904 2SC3052
001:E29
PANEL_CTL
Q903 2SC3052
R908 22K
+5V_+12V
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
POWER
CONTROL
+3.3V_VDDP_ST JP1007 C1213 5pF 50V R1212 100 SCL_EYEQ/AMP 008:H16;001:B25;007:AD7 R1213 100 2 L1006 BG2012B080TF C1212 5pF 50V 3 SDA_EYEQ/AMP 1 L1005 BG2012B080TF 12505WS-15A00 JP1010 P1001
R1206 4.7K
SCL
KEY1
001:J13
KEY2
JP1005 5 +5V_ST 6 JP1004 0 R1209 7 JP1001 8 C1207 0.1uF JP1008 0 R1208 9 PWM_LED 001:B6;001:G12 OPT 10 0 JP1006 R1214 0 OPT JP1009 12 R1211 50V L1002 BG2012B080TF GND-EMI C1208 1000pF 50V L1007 BLM18AG221SN1D C1202 1000pF 50V
009:X18
+3.3V_IR
GND-EMI SPK_N YAMAHA 100K OPT L1004 BG2012B080TF JP1003 R1207 SPK_P 100K YAMAHA C1209 100pF 50V OPT JP1002
ZD1200
5.6B
Copyright 2008 LG Electronics. Inc. All right reserved. Only for training and service purposes
JP1011 C1203 0.1uF 50V C1205 0.1uF 50V 4 11
L1001 BLM18AG221SN1D
C1201
0.1uF 50V
001:H22
IR
NC GND
13
RESET
R1202 0
001:H24
LED_G
LED_G
14
LED_R/PWM
15 JP1012 16 GND
GND
R1201 0
001:G12
LED_R
OPT
L1010 BG2012B080TF
IR & LED
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
P/NO : MFL42276206