Professional Documents
Culture Documents
700 Type 6
700 Type 6
Operation
The BERMAD Model 700E Type 6 is suited for a dual detection system, dry and electric. It is used as the primary
control valve in automatic systems including open nozzles and a dual fire detection system. The 700E Type 6 is held
closed by pressure applied to the upper chamber of the main valve ➊.
In the SET condition, the water pressure, supplied through the restricted priming line ➋, is trapped in the upper
chamber by: a check valve ➌, a closed PORV ➍ (Pressure Operated Relief Valve) pilot valve and a normally closed
solenoid valve ➎. The PORV is held closed by the maintained pneumatic pressure in the detection line ➏. The
trapped water pressure holds the seal-disk of the main valve to the valve seat ➐. Sealing is drip-tight and the system
piping is dry.
The typical redundant detection system includes both a dry pilot line with thermal detectors, and an independent,
electrically-controlled detection system.
In a FIRE or TEST condition, the 700E Type 6 trips upon receiving a command from one of the detection systems or
by the manual release ➑. Water exits the accelerator ➒ faster than it can be supplied to the upper chamber,
allowing the main valve to open and water to flow into the system piping and to the alarm device.
For installation and maintenance, see BERMAD publication "700E Type 6 - IOM".
pneumatic pneumatic
➍
➏
➌
➋ ➒
➑
➎
to drain
➊
➐ to alarm
System Components*
1 - Main Valve, BERMAD 700E Series
Basic Trim, includes "B" Items as listed(1)
2B - Accelerator & Priming Restriction
3B - Orifice Assembly
4B - Priming Strainer
6B - Pressure Operated Relief Valve (PORV)
7B - Check Valve
14B - Solenoid Pilot Valve
15B - Manual Emergency Release
18B - Priming Valve
19B - Drip Check W
Additional Accessories – "A" Items(2)
1A - Alarm Test Valve
2A - Gauge Valve
3A - Pressure Gauge
P 11A
4A - Alarm Strainer
5A - Drain Valve
11A - Alarm Valve
14A - Check Valve
Optional
3A
W - Water Motor Alarm 1
14A
P - Pressure Switch
19B
1A
2A 3A
5A 6B
4B 3B
18B 7B 2B
14B
15B
UL-Listed
The BERMAD Model 700E Type 6 Hydraulic
is UL-listed as a unit when installed
with specific components and accessories. Electric
* Notes: Pneumatic
1. "B" items are standard trim components provided in the trim package.
2. "A" items are additional trim components required for the proper installation and use of the deluge system.
For Ordering, add the suffix "A" to the model number. Atmosphere
Fire Protection
700E Type 6 Dry Pilot & Electrically-Controlled Deluge Valve
Specifications
TI 200 77/8 200 77/8 170 63/4 165 61/2 160 65/16 140 51/2 130 51/8
Tw 317.5 121/2 329 1215/16 340 133/8 351.5 1313/16 400 153/4 435 171/8 480 187/8
h 82 34/16 102 4 102 4 127 5 152 6 203 8 219 85/8
Th 390 153/8 401 1513/16 464 181/4 517 203/8 645 253/8 736 29 841 331/8
Tb 258 103/16 269 109/16 280 11 292 111/2 320 125/8 350 1313/16 382 151/16
Dv 3/4” 11/2” 11/2” 2” 2” 2” 2”
Notes:
1. Provide adequate clearance around valve for maintenance. 4. Data is for envelope dimensions. Specific component positioning may vary.
2. Listed trim dimensions are maximum. 5. For complete dimensions of 700E main valve, see BERMAD
3. Tw = maximum trim width for both "Y" and angle patterns. publication "700E Basic Deluge Valve".
Materials
Manufacturers Standard Materials Optional Materials Solenoid Pilot Valve
Main valve body and cover Main valve body and accessories Standard model
• Ductile iron ASTM 536(1) • Stainless steel 316 • Enclosure: General purpose water-
• Carbon steel ASTM A216-WCB(1) • Marine bronze tight NEMA 4 and 4X / IP65
Main valve wetted parts (internals) • NiAl-bronze • Optional: Explosion-proof
• Stainless steel 304 and coated steel • Titanium Voltage
Control Trim System • Duplex and Super-duplex • 24, 110, 220, AC 50 Hz
• Accelerator: Brass ASTM B21 Main valve and accessories internals (or 24, 120, 240, AC 60 Hz)
• Forged brass fittings & copper tubing • Stainless steel 316 • 24, 120, DC
Elastomers • Bronze • Continuous duty-molded Class F
• NBR • Titanium • Wattage rating: 10.6 DC, 9.5 AC
• Copper-nickel Approvals
• Hastalloy • UL-listed
Notes:
1. Epoxy coated, fusion bonded - standard.
Tubing and Fittings • CSA Certified
Other coatings available on request. • Stainless steel 316 • Alternative: CENELEC certified for
2. For seawater service see BERMAD • Copper-nickel EEx
publication "Seawater and Corrosive Media".
© Copyright 1999 by BERMAD Control Valves www.bermad.com The information contained in this document is subject to
Cat # PC7PE18 ver 4/00 change without notice. BERMAD shall not be liable for any
English E-mail: info@bermad.com errors contained herein. All rights reserved.