Professional Documents
Culture Documents
Metallized Polyester PCMT 369 Film Capacitors
Metallized Polyester PCMT 369 Film Capacitors
FEATURES APPLICATIONS
63
Pilkor components
P
P±1.5 P0 P
dt
P0
< Figure J > < Figure A > < Figure F > < Figure K >
64
Pilkor components
65
Pilkor components
66
Pilkor components
67
Pilkor components
68
Pilkor components
CONSTRUCTION
metallized polyester film
connecting wire
Description
MOUNTING
Normal use
The capacitors are designed for mounting on printed-wiring boards. The capacitors packed in
bandollers are designed for mounting on printed-wiring boards by means of automatic
insertion machines.
For detailed specifications refer to chapter packing.
In order to withstand vibration and shock tests, it must be ensured that the underside of the crimps are
in good contact with the printed-wiring board.
Unless otherwise specified, all electrical values apply to an ambient free air temperature of 23±1℃,
an atmospheric pressure of 86 to 106 kPa and a relative humidity of 50±2%.
For reference testing, a conditioning period shall be applied over 96±4 hours by heating the products
in a circulating air oven at the rated temperature and a relative humidity not exceeding 20%.
69
Pilkor components
CHARACTERISTICS
Dissipation Factor
Insulation Resistance
The insulation resistance is measured after a voltage has been applied for 1 minute ±5 seconds,
the voltage being 100±15V for the 100, 250 and 400 V versions and 500±50V for the 630 V versions.
The maximum pulse load are value valid for pulse voltage equal to the rated voltage. For lower
voltages the given values may be multiplied by VRdc and divided by the applied voltage.
100V 30 20 20 -
250V 120 45 20 15
400V 170 65 30 25
630V 90 90 35 30
70
Pilkor components
2 3
∆ C/C
∆ C/C
(%) 2
(%)
1 400V-630V
1
250V
0
0
-1
-1 -2
100V
-3
-2 -4
-5
-3
2 3 4 5 -60 -20 20 60 100 Tamb.(℃)
10 10 10 10
f(Hz)
Capacitance as a function of ambient free air temperature,
Capacitance change at 1kHz as a function of frequency ; typical curve
measured at 1kHz, 1V: typical curve
103
1.2
factor
dissipation
1.0 factor(X10-4)
0.8
0.6 102
0.4
0.2
0 101
-60 -40 -20 0 20 40 60 80 100
Tamb(C) 102 103 104 105
f(Hz)
Tangent of loss angle as a function of frequency : typical curve
Multiplying factor for DC and AC voltage as a function of temperature
105
RC(S)
104
103
102
-50 0 50 100
Tamb(℃)
RC-product as a function of ambient free air temperature ; typical curve
71
Pilkor components
100 103
AC AC
voltage voltage
(V) (V)
102
10
1.5 ㎌(Imax=12.5mm) 10
1.0 ㎌(Imax=12.5mm)
3.9 ㎌(Imax=12.5mm)
2.2 ㎌(Imax=12.5mm)
10 ㎌(Imax=12.5mm)
10 ㎌(Imax=12.5mm)
1
1
102 103 104 105 106 102 103 104 105 106
f(Hz) f(Hz)
AC voltage (RMS value) as a function of frequency AC voltage (RMS value) as a function of frequency
at Tamb≤85℃ for URdc=100V at Tamb≤85℃ for URdc=250V
103 103
AC
AC
voltage
voltage
(V)
(V)
102 102
100 ㎋(Imax=12.5mm)
10 10 100 ㎋(Imax=12.5mm)
220 ㎋(Imax=18.0mm)
220 ㎋(Imax=18.0mm)
1.0 ㎌(Imax=26.0mm)
1.0 ㎌(Imax=26.0mm)
2.2 ㎌(Imax=31.0mm)
1 1
102 103 104 105 106 f(Hz) 102 103 104 105 106 f(Hz) 10
7
AC voltage (RMS value) as a function of frequency AC voltage (RMS value) as a function of frequency
at Tamb≤85℃ for URdc=400V at Tamb≤85℃ for URdc=630V
72
Pilkor components
APPLICATION NOTE
1. The peak voltage (Vp) shall not be greater than the rated DC voltage.
2. The peak-to-peak voltage (Vp-p) shall not be greater than 2√2 times the rated AC voltage to avoid the
ionization inception level.
3. The peak current (Ip) shall not exceed the maximum peak current, defined as maximum voltage
pulse slope (dV/dt) multiplied by the capacitance.
Or the voltage pulse slope shall not exceed the rated voltage pulse slope. If the pulse voltage is
Lower than the rated voltage, the values of the table may be multiplied by VRdc and divided by the
applied voltage.
4. The dissipated power shall not be greater than the maximum permissible power dissipation
stated above.
5. The free air ambient temperature for the capacitor is not exceeding the category temperature.
6. Since all metallized film capacitors have an intrinsically active flammability risk, it is recommended
that these capacitors should only be used in circuits where the power can be limited to less than
5W to the capacitor should a failure occur.
PRODUCT MARKING
The capacitors are marked in black ink on the side with the following information :
73