SUPER SERVO INTEGRATED STEREO AMPLIFIER MODEL A-B017 SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 6 ON THE Schematic diagram and IN THE parts list are CRITICAL FOR RISK OF FIRE and ELECTRIC SHOCK.
SUPER SERVO INTEGRATED STEREO AMPLIFIER MODEL A-B017 SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 6 ON THE Schematic diagram and IN THE parts list are CRITICAL FOR RISK OF FIRE and ELECTRIC SHOCK.
SUPER SERVO INTEGRATED STEREO AMPLIFIER MODEL A-B017 SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 6 ON THE Schematic diagram and IN THE parts list are CRITICAL FOR RISK OF FIRE and ELECTRIC SHOCK.
SUPER SERVO INTEGRATED STEREO AMPLIFIER MODEL A-B017 SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 6 ON THE Schematic diagram and IN THE parts list are CRITICAL FOR RISK OF FIRE and ELECTRIC SHOCK.
Ceo)
SERIAL No. 3147
ONKYO SERVICE MANUAL
SUPER SERVO INTEGRATED
STEREO AMPLIFIER
MODEL A-8017
UDN, UD | 120V AC, 60H
GV. UG | 220V AC. Sie
Tow | 120 or 200 a6, Soe
‘SAFETY-RELATED COMPONENT WARNING! TABLE OF CONTENTS
COMPONENTS IDENTIFIED BY MARK 4 ON
ELECTRIC SHOCK. REPLACE THESE COM- Specifications 2
PONENTS WITH ONKYO PARTS WHOSE PARTS Block diagram 2
NUMBERS APPEAR AS SHOWN IN THIS MANUAL. Precautions 4
MAKE LEAKAGE-CURRENT on Resistance | MUM :
‘ONKYO.
| AUDIO COMPONENTSSPECIFICATIONS
Mois Power Output: 2 180 watuat chm, Sipalto ose Rate: Phano Oy
iti) SOD IMF .202,
se iD staat ons, sat Comp
pay ron MC)
Coninuous Power Oupu: Dt IIS wats 4 os, 60D 4.202, 05 nV
kHz (DIN) input, 1 watt output)
sree ace ons, oro ape
iteony 349 (HF 202,05
Baer chanel min RMS pat met ute
sre ont bt shane i bas
Tactic soicoaaate, — ewconnt: ——“Sedbbe THe +5 Da
sino move than 015% wou
TH. SobionieFiter: isis (6/04)
‘Total Harmonic Distortion: 0.015% at rated power, High Cut (TREBLE MIN): 6 kHz (6 dB/Oct.)
meee ook tined pee
DunpingFacir: Oat @chns Caner
Pregueny Repos! S000 He #1 &B Senioudicom: 10:3 TR:S1 Diode: 26
Rian Devon Hh); 20200008 #03 aB Dmnenos 155(¥) x 2) 45920}
‘Sensitivity and Impedance: Phono (MM): 2.5mV/SO kohms 17-1/8"'xS-9/16""%x15-7/16""
Phono (MC): 280uV/330 ohms Weight: 11.5 kg (25.4 Ibs.)
‘Tuner: 150 mV/50 kohms
‘Tape Play: 150 mV/50 kohms Specifications and features are subject to change without
‘Tape Rec: 150 mV/3.3 kohms notice.
(gue)
PronoOvelost: 210 nV RST,
oo1se THD
bass Cont: te abst THe
PrbleConwat: $B aps 20000%
BLOCK DIAGRAM
reno se nee
1 cops wt ser se wate sone se
moro [ 8-8 a fote
@ “Meh 5
com =
‘LOUDNESS
sen semen
wwe woes
sexo mp
ino FSET rs car one
ve ca
LegePRECAUTIONS
1, Replacing the fuse
For continued protection against risk fire, replace only
with same type and same rating fuse.
CIRCUITNO. PARTSNO. DESCRIPTION
F901 252081 GA(ST6), ACfuse(120V model)
F901 252085 GAT, AC use (120V/220V
model)
F902 252076 —_BISA-SE-EAK, AC fuse
{@20V, 120V)220V model)
F700 252070 TASE-EAK, AC fuse
(220V model)
FLF2 252019 6.3ASE-EAK, DC fue
(220V model)
2, Replacing the lamps
‘This unit uses the lamps listed below.
eincurr No, PARTS No.
PLoO1, PLOO 210153
PLIAV, 0.06AW-1.0,
‘Speake? switch indleator
PLIAV, 0.06AW-1.0,
Rec. selector indicator
PL301, PL302_ 210185
1303 210180 PLUSV, 0.08AW-1.0,
Input selector indicator, Phono
PL304,PL305 210146 PLLA, O.06AW-10, Input
selector indiator, DAD/AUX
PL306,PL307 210147 PLIAV,G.06AW-i.0, input
tector Indias, TAPE
PL701 2101468 —-PLIAV, 0.06AWi.5,
Power indiator
L702 2101s) ——-PLISW,0.08AW-L5,
Servo indicator
MAIN AMPLIFIER ADJUSTMENT
MAIN AMPLIFIER ADJUSTMENT
Set the all control knobs to standard position
Standard knob position
INPUT SELECTOR TUNER
CARTRIDGE SELECTOR MM
PHONO SELECTOR PHONO
REC SELECTOR OFF
MODE, NORM
MUTING OFF
SUBSONIC FILTER OFF
BALANCE Center
VOLUME, Minimum
LOUDNESS OFF
BASS DEFEAT
TREBLE DEFEAT
SPEAKERS A
3. Insulation resistance mesurement
Connect the insulating-resistance tester between the plug
‘of power supply cable and the terminal GND specifi
tions; D model, G/W model
4, Voltage selector (rear panel)
Worldwide models are equipped with a voltage selector
to conform with local power supplies. Be sure to set this
switch to match the voltage of the power supply in your
area before turning the power switch on, Voltage is
changed by sliding the groove in the switch with a scre
driver or similar instrument to the up or down position.
Confirm that the switch has been moved all the way to
the up or down before turning the power switch on. If
there is no voltage selector switch on the unit you have
purchased, it can only be used in areas where the power
supply voltage isthe same as that of the unit,
Be ee —
oF av Hew
IDLING CURRENT ADJUSTMENT
1. Connect the DC voltmeter between Imp and Ver
terminals,
2. Adjust the voltage to 12V4SmV with semi-fixed resistor
of R538 and R638,
NOTES: Adjust after switching on for 5 minutes.
VOLUME
LOAD
Minimum
Open