Professional Documents
Culture Documents
NM24 SR US 8Nm 19558
NM24 SR US 8Nm 19558
NM24-SR US
Proportional damper actuator, non-spring return, direct coupled,
24 V, for 2 to 10 VDC and 4 to 20 mA control signal
© Application
For proportional modulation of dampers in HVAC sys-
tems. Actual actuator sizing should be done in accor-
dance with the damper manufacturer’s specifications.
The actuator mounts directly to the damper operating
shaft with a universal V-bolt clamp assembly.
Operation
LISTED The actuator operates in response to a 2 to 10 VDC, 2 to
94D5
TEMP. IND &
REG. EQUIP.
UL
10 V phasecut or, with the addition of a 500Ω resistor, a
4 to 20 mA control input from an electronic controller or
positioner. A 2 to 10 VDC feedback signal is provided
for position indication or master-slave applications.
Technical Data NM24-SR US A built-in microprocessor automatically tests for the
amount of rotation required to modulate the damper fully
Power supply 24 VAC, ± 20%, 50/60 Hz 24 VDC, ±10%
closed to fully open. The actuator will self-adjust to run
Power consumption 1.3 W at a consistent running time of 150 seconds, and rescale
Transformer sizing 3.5 VA (Class 2 power source) the input signal so the entire 8 volt control range is used
Operating range Y 2 to 10 VDC, 4 to 20 mA to provide maximum resolution of the control system.
The microprocessor will also correct for compression of
Input impedance 100kΩ (0.1 mA), 500Ω
tight close-off gaskets with age, providing the actuator is
Feedback output 'U' 2 to 10 VDC, 0.7 mA max not on its mechanical stops. A functional test of the actu-
Electrical connection 3 ft, 18 GA plenum rated (UL CL2P) cable, ator-damper assembly may be done by pressing in the
1/2” conduit connector manual override button, this will activate the actuators
Overload protection electronic throughout 0 to 95° rotation test mode and cycle the actuator fully open and closed.
A 2 to 10 VDC feedback (U) is provided with full 8 volt
Torque (Note 1) min 70 in-lb (8 Nm)
output range proportional to the operational rotation of
Damper area (Note 2) 18 sq ft the damper.
Direction of rotation reversible with Switch “L-R” A digital rotation sensing circuit protects the actuator in a
Note 2 Damper area is calculated using approximately 4 in-lb/sq ft of damper area. This 3 3/16"
is an average torque requirement for good quality dampers operating under a 1" [81]
WC pressure drop. Check damper specifications for exact torque requirements. 7/32"
[5.2]
Note 3 The on board microprocessor measures the actuators full stoke on startup.
It then adjusts the actuator speed to ensure 150 second run time for 35°-95°.
D016
Below 35° stroke, the speed is constant and run time varies with rotation angle.
102
®
NM24-SR US
Proportional damper actuator, non-spring return, direct coupled,
24 V, for 2 to 10 VDC and 4 to 20 mA control signal
Wiring diagrams
W094
W095
1
24 VAC Transformer 2 1 2
5 24 VAC Transformer 5
4 4
Line Blk (1) Common Blk (1) Common
Line
Volts Red (2) + Hot Volts Red (2) + Hot
Ω
2 to 10 VDC (–) 4 to 20 mA (–) 500Ω
Control Signal (+) Wht (3) Y 2 to 10V Input Control Signal (+) Wht (3) Y 2 to 10V Input
6
Grn (4) U 2 to 10V Output Grn (4) U 2 to 10V Output
2 to 10 VDC (–)
L R Feedback Signal (+) L R
NM24-SR US 3 NM24-SR US
Notes:
NM
has been discontinued as of October 2003 The 500Ω resistor converts the 4 to 20 mA control
6 signal to 2 to 10 VDC.
T-Type bracket
These are included in the single-actuator
packages.
103