Professional Documents
Culture Documents
English G24SE 24V CarAlarm
English G24SE 24V CarAlarm
English G24SE 24V CarAlarm
E N GL IS H
G24 SE 24V
(External Shock Sensor)
Version 3
22 www.geniuscaralarm.com
Genius Car Alarm
E N GL IS H
• Negative output Channel 2 (Opens electric trunk)
• Negative output Channel 3 optional modules (Programmable)
• Opening the electric trunk without deactivating the alarm using the transmitter
(channel 2)
• LED indicator on the board
• Programmed controls identifier (P.C.I.) (Programmable)
• 1 Positive output for Light flash with internal relay in the module
• Central Door Lock on Negative
• Automatic Armed (Programmable)
• Electric locks on with the Automatic Armed (Programmable)
• Ignition Lock and unlock (Programmable)
• Double push button to unlock door
• Automatic Rearm (accidental disarm)
• Automatic Rearm with Lock
• Shock Sensor bypass by transmitter
• Line door pin switches (Positive or Negative)
• Line hood and trunk pin switches (Negative)
• Electronic siren of 120 dba
• Mode Valet (using emergency button or Transmitters )
• Wires identified by colors
• Protection fuses included in the installation harness
• Transmitter Anti-carjack (Programmable)
• Door Anti-carjack (Optional)
• Ignition Anti-carjack (Programmable)
• Presence Anti-carjack (Additional transmitter) (Programmable)
• Warning Light when anti-carjack activates
• Acoustic warning when anti-carjack activates (Programmable)
• Negative output in armed, for engine cut
• Second engine cut (Programmable)
• Negative output timed for windows-up modules (Programmable)
• Defective zone exclusion
• Flashing output for the horn (Programmable)
• Dome Light (Programmable)
• Function programming through software
• Manual disarmed by safety PIN code (Programmable)
• Memory of last status of the system.
www.geniuscaralarm.com 23
Genius Car Alarm
Introduction
Thank you for purchasing our security system for your vehicle. Read well the user’s
manual of the system specifically the functions of the transmitter, the valet switch and the
LED indicator on the board.
The Transmitter
Each transmitter has a different code, the alarm system is programmed by the factory with
2 codes (2 transmitters), and you can program a maximum of 4 codes (4 transmitters). The
transmitter has 4 buttons, I, II, III, IV.
The system is pre-programmed with a work routine with each button of the transmitter.
It works with the following configuration:
Button I
E N GL IS H
Button IV
To enter the memory and be able to program the transmitters, follow these steps:
The system pre-programmed with a routine of work with each button of the Transmitter. It works
with the following configuration:
E N GL IS H
trigger. SOUNDING
1. The first, using button I on the transmitter. It is necessary for the ignition switch to
be OFF and for the system not to be on Valet.
2. The second, using the automatic armed, which is obtained when the ignition switch
goes from ON to OFF and then open and close a door. The system will
automatically arm in 30 seconds after closing the last door, this functions is
programmable (see function programming chart).
www.geniuscaralarm.com 25
Genius Car Alarm
Alarm system armed by using the Transmitter.
The alarm system will always be armed by using the transmitter, provided that the ignition
switch is OFF and the system in not in the Valet mode.
To arm the alarm system after leaving the vehicle and closing all the doors, simply press
and let go button I on the transmitter once, the lights will flash once, the siren will sound
once and the LED indicator on the board will start flashing slowly to confirm that the
system in armed. If the electric locks are connected to the alarm system, they will be
locked; the current breaker will be activated avoiding the use of the vehicle, after 3
seconds the system goes to expecting-robbery mode
will flash 3 times indicating a door is not properly closed and it will exclude the sensors of
that zone. The defective zone will be included again in the protection 3 seconds after
correcting the failure, alter properly closing the trunk.
Silent Arm
First press and let go button III and then press and let go button I on the transmitter to arm
the alarm system silently, the alarm system will arm without the sound of the siren. When
the alarm is silently armed and a door is open or not properly closed, the siren will sound 3
times as an alert warning.
Silent Disarm
First press and let go button III and then press and let go button II on the transmitter to
disarm the alarm system silently, the system will disarm without the sound of the siren.
When silently disarmed and after the vehicle has been victim of a carjack attempt, the
siren will sound 3 times as an alert warning.
E N GL IS H
button the number of times assigned in the security code (1 as set by the
factory) the siren will continue to sound for 3 seconds and if the security code
is right the system will disarm.
PANIC
With this function, we can make the system to trigger intentionally to prevent or attract the
attention of people, in case of a theft or aggression attempt.
CAR FINDER
With this function we can make the system to send us signals with the siren and lights,
which will serve us to locate the vehicle, whenever we are in the transmission range
between the remote control and the vehicle.
www.geniuscaralarm.com 27
Genius Car Alarm
ANTI-HIJACKING BY TRANSMITTER (Programmable)
This function is used to immobilize the vehicle in case of emergency, pressing the buttons
1 and 2 simultaneously for 3 seconds and the anti-hijacking mode will activated by
transmitter. (See Functions Programming Table)
ANTI-HIJACKING SEQUENCE
When the system enters in anti-hijacking mode,
a. 0 to 15 seconds, nothing happens (See Functions Programming Table, function 9).
16 to 30 seconds, the LED twinkles slowly.
31 to 45 seconds, the LED will flash rapidly, the siren will chirp once every two
seconds and the lights will flash once every second.
46 to 70 seconds, the LED will flash rapidly, the siren will chirp once every second
and the lights will flash once every second.
After 70 seconds, the siren and the lights will trigger, the engine interrupter will be
activated.
b. When the anti-hijacking is triggered, (the ignition remains in ON position). Even if the
ignition key is turned to OFF position, the siren and the lights remain triggered for 3
minutes.
c. If the ignition key is turned to ON position again, the siren and the lights will be
triggered again.
AUTOMATIC REARMING
When the alarm is disarmed with the remote control, without turning the ignition key to ON
position and without opening the doors, 30 seconds later the alarm will be re-armed and
the doors will be locked.
E N GL IS H
CHANNEL 2 (TRUNK)
a. When the alarm is disarmed:
CHANNEL 2, BUTTON 4 FOR 3 SECONDS, the signal is triggered (The trunk will be
opened)
b. When the alarm is armed:
Activating channel 2, first the alarm will be disarmed and then the signal is triggered. (The
trunk will be opened)
* See Programming Table
CHANNEL 3
With this signal we can control a function (connecting an additional- optional module) such
as a window module, or the engine ignition.
Press buttons 3 and 4 together for two seconds to activate the function. (If the buttons are
pressed for more time, the signal is applied; releasing the buttons will stop the signal)
* See Programming Table
HORN OUTPUT
Normally, in alarms the sound is produced by a siren (Positive Output), with this new
system, we can simultaneously drive the horn’s sound (Negative Output), or select one of
the two functions.
* See programming Table
VALET MODE
Valet, it is the function that allows us to cancel temporarily our security system, for those
situations in which we do not want to use the alarm system, for example in the car washer,
while in maintenance services, etc.
one of them.
a. After the engine ignition is on, the doors will be locked 2 seconds later.
b. Once the engine is turned off, the doors will be unlocked immediately.
INSTRUCTIONS
* LED’S CONDITIONS
a. Armed Alarm: The LED will flash slowly (once every second)
b. Automatic Arming and Re-arming: The LED will flash rapidly.
c. Valet Mode: LED will light solid.
FUNCTIONS PROGRAMMING
a. Turn the ignition key to ON position.
b. Within 10 seconds, press the valet switch 5 times.
c. The siren will chirp 3 times.
d. Press the valet switch the number of times of the selected function.
* The siren will sound every time the valet switch is pressed.
e. Press the button in the remote control of the selected option.
* If the button 1 is pressed, the siren will chirp once (1); if the button 2 is pressed, it
will chirp twice (2), and three chirps if button 3 is pressed.
f. To exit the programming mode, turn the ignition key to OFF position.
* The siren will sound a (1) long beep.
E N GL IS H
PROGRAMMING TABLE
2
WITHOUT Delay of 30 Delay of 60
Door’s Signal Activation Delay
DELAY seconds seconds
3
Anti-hijacking by transmitter
YES NO
4
Lock Doors with Ignition YES NO
5
Unlock Doors with Ignition YES NO
6 HORN
Second Pulse to CHANNEL 3
OUTPUTS FOR CHANNEL 3 OUTPUT
Unlock Doors
(-)
7 Anti-hijacking Warning
*Indicates the beginning of the YES NO
sequence
8
ARMED and DISARMED Notices YES NO
9
Reminder to arm the alarm.
YES NO
*Only in Manual Arming
10
Opened Door Warning YES NO
11 30 second
Electric
Channel 2 Electric Trunk Dome Light
window
lifter
12
Anti-hijacking by Door Close Door Opend Door
www.geniuscaralarm.com 31
Genius Car Alarm
13
FABRIC RESET SI
a. Select the functions to be changed. (It is recommended to write down them to avoid
mistakes)
b. If you are going to work with 2 or 3 functions, follow these steps:
c. Function # 2: Press valet switch twice and then select button 1.
d. Then, if you wish to program, function #4, press twice again the valet switch (to
E N GL IS H
IMPORTANT: Going from one function to another, just press the valet switch the
number of times necessary to complete the following function.
3. ANTI-HIJACKING BY TRANSMITTER
This function is used to immobilize the vehicle in case of emergency; pressing the buttons
1 and 2 simultaneously for 3 seconds while the engine is running, the siren will chirp once
and the parking lights will flash once; after 15 seconds, the LED will start to twinkle
indicating the activation of the anti-hijacking mode. This function is programmable (See
Functions Programming Table)
E N GL IS H
11. CHANNEL 2
Function’s Selection- Trunk’s release or dome lights:
DOME LIGHTS – Negative Output Signal for 20 seconds. When disarming, if the ignition
key turns to ON, the dome lights turn off.
TRIGGERED, the dome lights are intermittent.
www.geniuscaralarm.com 33
Genius Car Alarm
E N GL IS H
34 www.geniuscaralarm.com
Genius Car Alarm
BENEFICIARY
Name: __________________________________
C.I.:_________________________
Model: ____________________________
E N GL IS H
STAMP AND SIGNATURE OF THE DISTRIBUTOR THAT INSTALLED THE SYSTEM
TECHNICAL REVISION
ST
1 Date ___________________________________________________________
Observations____________________________________________________
Stamp: __________________________________________________________
Observations ____________________________________________________
Stamp: __________________________________________________________
3rd Date_____________________________________________________________
Observations ___________________________________________________
Stamp _________________________________________________________
www.geniuscaralarm.com 35
Genius Car Alarm
LIMITED WARRANTY
Every GENIUS branded alarm system is guaranteed for ( ) year(s) since the installation
date considering the following conditions:
2. The costs of dismantling, assembling or any other will be borne by the claimant.
3. The implementation of this guarantee will have greater flexibility in its dealings, if the
user has placed the sticker on the rear window of the vehicle.
E N GL IS H
4. The technical department of the company reserves the right to determine the validity
of the guarantee according to expertise.
1. Anti-hijacking Disarming
With the ignition key in ON position, press the reset button 1 time, wait 3 seconds and the
anti-hijacking mode will be disarmed.
2. Manual Disarming
Turn the ignition key to ON position, press the reset button 1 time, wait 3 seconds and the
alarm’s system will be disarmed.
Important: Plastic and store these instructions and take it with you always.
Technical Specification
36 www.geniuscaralarm.com