Professional Documents
Culture Documents
Kat Walk Mini Owner's Manual
Kat Walk Mini Owner's Manual
OWNER'S MANUAL
Foreword
First and Foremost 04
Declaration 04
Safety Instructions 05
Health Warnings 07
Product Introduction
Product Description 08
KAT Walk mini Description 08
KAT Walk Special Shoe Covers Description 08
KAT Walk mini Adapter Description 08
Product Appearance 08
Product Parameters 09
02
Kat Walk mini First Use 20
Stepping On 20
Height Adjustment 21
Harness Wearing 22
Walking Tutorial 23
Accessories Set-up 23
Stepping Off 24
Appendix
Appendix 1:Optional Accessories List 29
Appendix 2:KAT Control Center 33
Appendix 3:KAT PiSystem Adapter 42
Appendix 4:KAT Walk mni & Oculus Rift Connection Instructions 48
Appendix 5:Contact Information 51
03
First & Foremost
This owner's manual contains all the information you need to install the KAT Walk mini.
The following symbols are used to indicate crucial information and instructions for the set-up
process:
This symbol is a hint, letting you know what might be helpful at that particular point.
This symbol is important: You must complete one or more of the hardware and software
installations or settings as described in the manual.
This symbol is a safety warning, to remind you to be wary of your personal safety while
performing the task, be mindful of this symbol to avert any potential risks.
Declaration
It is the trademark of Hangzhou Virtual and Reality Technology Co., Ltd. All
trademarks, product identification and trade names of other companies appearing in this
manual are owned by their respective owners. No parts or content of this manual may be
copied or reproduced without the written permission of the company, and may not be shared
in any form or used for any commercial or profitable purpose.
The contents of this manual are subject to change due to product upgrades or other reasons.
Our company reserves the right to modify the contents of this manual without any notice or
prompt. This manual is intended as a guide only. We do our best to provide accurate informa-
tion in this manual, but we do not guarantee that the contents of the manual are completely
error free. All statements, information, and recommendations in this manual do not constitute
any warranty, express or implied.
For the latest information, please feel free to check out our official website:
http://www.katvr.com/
04
Safety Instructions
To avoid injury or damage to the product, read and follow all assembly and operation
instructions before using the KAT Walk mini.
This device is intended for use by healthy people aged 14 to 60 years, of 1.40m (4'7'') to
1.95m (6'5'') height, and weighing no more than 130kg (285lb). Do not use the KAT Walk mini
if you do not meet the age, height, or weight requirements, or if your physical condition is
not capable of moderate to intense physical activity.
If you are uncertain of your health condition, please consult your doctor first.
Please use the device according to proper instructions or under the guidance of a profes-
sional to avoid damage.
Pregnant women or those with epilepsy, cardiopulmonary diseases, eye diseases, mental
illnesses, anemia, and people undergoing postoperative recovery etc. are strictly prohibited.
The device contains moving parts. Do not approach during use to avoid accidents, especial-
ly for children or pets. Please keep a safe distance of more than one meter.
To avoid damage to the plate or harm to yourself, please use the special shoe covers and
harness according to instructions while in use. The shoe covers are for their sole purpose, it
is strictly prohibited to use them for other purposes.
Check the device before use to confirm that it’s in a normal state without cracks, scratches,
bumps, bends, odd movements or other signs of wear and tear. Check all connections and
moving parts to ensure that the nuts, bolts, and other joint structures are securely fastened.
The base plate is slippery. Please ensure that the rotation lock mechanism is in place before
getting ON/OFF the device. Hold the designated area on the supporting rod then proceed to
get ON/OFF the device.
Make sure the harness is properly worn and fastened during use. Do not use this device
without the harness.
Do not take your foot out of the base plate’s bounds while in use.
Please pay attention to the gap between the base plate and its frame to avoid safety risks.
05
Be sure to read and follow all product instructions and warnings related to your VR headset
of choice.
Choking hazard: Do not leave small components that pose a suffocation hazard to children
or pets where they can reach.
Do not place the device and its other components near fire or heat sources, nor try to leave
it directly exposed to the sun.
If you need to change location after installation, be sure to disassemble it in strict accor-
dance with the components’order, use the same material as the original packaging to wrap
the device, and choose a high-quality logistics or handling company, otherwise the product
may be prone to damage.
Keep the device safely away from liquids or containers holding liquids,and keep it dry.
Please turn off the power of the relevant equipment before pulling out the plug.
When removing the power cord, be sure to pull it up from the plug, and do not pull the cord
directly.
Before connecting the device to the socket, please confirm that the actual socket voltage is
compatible. If the voltages of the two do not match, do not connect the device to the power
socket.
If you violate the above safety instructions or carry out other violations, it may cause
personal injury or adverse consequences, and KAT VR will not be responsible.
06 06
Health Warnings
The following health warnings are updated regularly to ensure accuracy and relevance:
Before use, you need to read the product manual carefully and follow given instructions.
Symptoms of discomfort may be nausea, dizziness, or headaches. If you feel any discomfort,
please stop using it immediately and do not engage in any activities that pose a safety
hazard until the symptoms subside.
During the use of this device by a child, a guardian should always be present to ensure that
they do not experience any of the above discomforts. If it’s your first time, shorter periods of
use are advised. Only when you have adapted to the virtual reality, is it advised to gradually
increase the length of use.
If you are fatigued, hangover, under the influence of alcohol or drugs, emotionally stressed
or anxious, has headaches or an earache; it is strictly forbidden to use the device, otherwise
your condition will be aggravated.
Anyone who has the following symptoms when using the device should stop immediately:
(a)Seizures, loss of consciousness;
(b)eye fatigue, eye muscle twitching, blurriness or other visual abnormalities;
(c)impaired body balance or hand-eye coordination;
(d)lethargy, nausea, excessive sweating, or any symptoms indicating to motion sickness.
Symptoms caused by virtual reality may persist and become more apparent in a few hours.
For your personal safety, do not drive, operate machinery, engage in other activities that are
visually or physically demanding or require body balance and hand-eye coordination, until
full recovery.
Those who use this device are considered to have full capacity of civil conduct and
have complied with the aforementioned matters.
07
Product Introduction
Product Description
The KAT Walk mini is a small, lightweight VR omni-directional platform, also known as a VR
treadmill. It bridges the virtual worlds with reality, allowing you to achieve 360° infinite action
in the virtual world in a compact space. It helps you achieve a safe, free, and deeply immersive
walking experience in virtual reality with its non-restrictive design, six-degrees-of-freedom
motion simulation, height and body adaptive, etc. Multiple applications include VR gaming
and Industrial use.
The shoe covers are specifically designed for the KAT Walk mini and to be solely used for this
purpose. They use constant friction to simulate the curve and displacement of the foot when
you walk. The base plate’s design is to simulate natural bipedal movement, ensuring a natural
feeling gait for that accentuated VR immersion. It is advised to use the KAT Walk mini special
shoe covers without changing shoes to get suited-up faster.
KAT Walk mini Adapter developed by KAT VR is to ensure that KAT Walk mini functions properly
on the condition that it is well-connected.
Product Appearance
Back Support
Height Adjuster
Harness
Safety Buckle
Hooks
Seat
Adjustable Buckles Rotation Lock
Leg Straps
Connecting Wire Supporting Rods
Base Shell
Base Plate
10 Safety Step
08
Product Parameters
09
Installation Preparation
Due to possible safety hazards in the installation process, please be cautious. Read the
suggestions we’ve compiled for you carefully before attempting installation.
Precautions
Before unboxing the KAT Walk mini, please prepare a pair of scissors, a screwdriver and a
claw hammer, wear protective gloves as well as the appropriate footwear for such handiwork,
slippers or high-heeled shoes are unsuitable.
Please note that the gross weight of the package is approximately 163 kg. Please have at
least two adults assist with the unboxing to ensure no damage is done to either you or the
product.
Remove any obstructions in the handling process so as not to scratch the walls or the floor.
Placement
Place the device near a computer so as to ensure that the USB cable is accessible.
It is not advised to place the device on any easily scratched surfaces, such as wooden or
tiled floors.
Place the device on leveled ground for its stability during operation.
Ensure there are no objects or household items that can be knocked over within its vicinity.
The following instructions will use the HTC VIVE as the Premium VR headset but the
adaptable VR headsets are not limited to the HTC VIVE.
10
Tool Preparation
Please check carefully that the package came with the proper number of each tool or
accessory. If any item is missing, please contact customer service(service@katvr.com).
List of Items
Back support 1
Main Components
Supporting rods 1 2 rods on each side
Safety step 1
Level 1 18mm*9mm
screw M8 X 16 with
1 For installation
8mm gasket
11
Product Installation and Assembly
power outlet
01 02
85KG 60CM
Remove the base frame marked Proceeds to lift up the base which The side with sticker“1”should
with a sticker“5”,and set it weighs approximately 85kg and face forward, as shown in the
aside for assembly. place it on a flat surface at least picture.
60cm away from the wall.
03 04
12
Assembly of the Back Support
The surface of joint may leave some scratches when assembling due to the necessary test at
the factory, but it won't affect your use of KAT Walk mini.
05 06 07
Take out the large hex hey/allen Take out a supporting rod marked Take out a supporting rod marked
key from the toolbox and with sticker“2”and insert it into with sticker “3” and insert it
remove the four screws tight- the vertical tube on the left side into the vertical tube on the left
ened at the base frame’s foot on of base with sticker“1”. side of base with sticker“1”.
two sides and put them aside.
08 09 10
Lift up the hose a little bit so as To complete this procedure, you Secure the height adjuster by
to insert the supporting rods need to make sure that the top locking it, in case of accidental
until they have been lowered to of the hose aligns with the surface falling of back support when
the very end. of the base frame as shown in installing.
the picture.
13
11 12 13
Unscrew the screws from the Insert the bolts of the back support Tighten the screws on each side
back support. to the square holes at the top of to the vertical tube at the top of
supporting rods, and ensure that the supporting rods.
the stickers“1”and“4”are aligned.
14 15 16
Use the hex key/allen key to tight- Securely tighten the bolt joining Remove the three cables tied to
en the four screws in place on the connecting wire to the base the base frame and sort out the
both sides, holding the support- frame. rotation lock wire.
ing rods firmly.
17 18 19
Unscrew the four screws Find the switch of the Tighten the four screws
fastened on the plate of the rotation lock at the base and removed earlier.
rotation lock and store put it together with the plate
them for the future use. on the supporting rod.
14
20 21 22
Fasten the supporting rod with Pull out the power and USB Slowly place the shell with the
the 2 velcro bandages on the cable of the base. sticker“5”onto the base, and
rotation lock wire. make sure that stickers“1”and
“5”are aligned.
23 24
6
Plug the base shell and plate Slide the safety step marked
as shown above. with the sticker“6”into the
gap of the base frame.
15
Connecting of Wires
25 26 27
The device has two cables in its Connect KAT Walk mini adapter In case the USB ports are
back: A power cable (A) that in a USB port of the computer. engaged, please use the
connects to a 3 prong adapter extension cable to connect the
cable and a USB cable (B) that computer and the KAT Walk
connects to your computer. mini adapter so as to make the
device to use as normal.
28
(For those who haven't chosen cord bracket, please follow the instructions for the
cord-organizer. But the setup are only for reference and cannot be used for warranty. )
01 02 03
PUSH
After making a hole into the Screw the screw hook into the Hang the cord-organizer onto
ceiling, insert the wall anchor. wall anchor tightly to hang the the screw hook and finish the
cord-organizer. whole procedure.
16
First Use Instructions
Sensor Instructions
Sensor Initialization
Every time after powering on the KAT Walk mini (such as
after connecting to your computer via USB or restarting
your computer), first initialize the sensor on the device
before using the device.
The following instructions will use the HTC VIVE as the standard VR headset but
the adaptable VR headsets are not limited to the HTC VIVE.
Please note that since the base frame adds height to ground level, set the ground level while
on the KAT Walk mini to 0cm as you would normally but your height settings should be 18.6cm
less to compensate for the elevation.
17
Sensor Calibration
If any of the situations below occurred before using the KAT Walk mini, the orientation of the
sensor should be calibrated in order to correctly map your physical actions into the VR game
or simulation.
Before sensor calibration, please make sure that the room setting for your VR headset has been
completed correctly and the sensor initialization operation has been performed.
01
“Calibration" button
03 04
Properly place your VR headset Click on the“Calibration" button as shown on the menu.
relative to the KAT Walk mini’s
position. Facing forward in line At this point, you have completed the KAT Walk mini’s
with the back support. sensor calibration.
18
KAT Walk mini Operating Instructions
I II III
Push Pull
19
KAT Walk mini First Use
Stepping On
01 02 03
Unlock the Rotation lock on Rotate the supporting rods Lock the Rotation lock to
the supporting rod. to the position shown above. fasten the supporting rods.
04 05 06
Put on the special shoe Fit your heel into the special Step onto the safety step.
covers. shoe covers then fasten the
buckle.
07 08 09
Hold firmly for support Step onto the surface of the Stand facing the back
where the label indicates. base frame and stand with support.
caution.
20
Height Adjustment
10 1 1.85-1.95m
2 1.75-1.84m
3 1.60-1.74m
4 1.50-1.59m
5 1.40-1.49m
Before adjusting the height,
(the height range shown above is for illustration purposes
make sure the harness is set at
the highest position. only,and your comfort will be the ultimate reference.)
11 12
Lift the back of the harness, adjust This is the possible For lowering, slightly lift up
it to a comfortable position on highest position. the harness with both
your waist and then slightly press hands.
it down to fix.
13
Push
And hold with one hand, push on This is the possible Turn forward to prepare to
the height adjuster to let the lowest position. wear the harness.
harness fall down to your intended
position then gently press it down
to fix it there.
21
Harness Wearing
This procedure is crucial because if the harness is not properly worn, you may not
have a good experience in walking.
14 15 16
Pull
Lean closely against the inner side of the harness Buckle up the To tighten the harness, pull the
and pull both sides of the strap, closing the ring harness for safety. left side of the strap with both
around the thinnest part of your waist (make sure hands until the adjustable belt
both sides connect above your crotch). Then, is to the tightest. Meanwhile, fit
stick the velcro as tight as you can to ensure your waist to the strap.
there is no space left.
18 19
22
Walking Tutorial
20 21 22
Accessories Set-up
25 26 27
Hang your VR headset and Unlock the Rotation lock. Game on.
controller on the hooks behind
the back support for easy
access while on the device.
23
Stepping Off
28 29 30
Rotate the supporting rods Lock the rotation lock to After removing your VR
to the position shown fasten the supporting headset and controllers,
above. rods. you can hang them safely
behind by the hook.
31 32 33
Undo the leg straps. Unfasten the buckle on the With one hand holding
harness. where the grip label
indicates, gently step off
with one foot onto the
34 safety step.
24
Software Adapter Instructions
System Requirements
Storage space: 100 MB free hard disk space (for installing the software adapter)
For other system requirements, please refer to instructions of your particular VR headset.
KAT I/O is a product management assistance tool developed by KAT VR for the individual
users.
With KAT I/O, you can instantly control the status of your KAT Walk mini’s functions and
features without leaving the virtual world, not to mention the inclusive library of KAT Walk
mini supported games. With Steam VR, KAT I/O will aid you to browse in-game features or
the product’s settings without having to take off your headset or leave the KAT Walk mini
to avoid interrupting your VR experience.
The KAT I/O VR platform function based on Steam VR will be provided later with the
software updates.
If you are a business customer, you can get access to the commercial version of the
software (KAT I/O Business Edition) through our sales staff.
Please use the browser to log in to the following website to get the product’s software
adapter you need:
http://www.katvr.com/katio/
25
Disassembly and Maintenance
Disassembly Procedure
If you need to move the KAT Walk mini, strictly follow the product’s assembly instructions in
the reverse order. Disassemble with caution to keep the main components intact.
After dismantling the device, gently place it in its original box and use similar material to pack-
age it. Use sufficient manpower or a good logistics company to handle with care, otherwise the
product may be prone to damage.
Product Maintenance
Before daily use, always wipe the base frame’s surface to rid it of dust and dirt that could
abrade the surface.
Routinely check the screws and bolts to ensure they are firmly tightened, parts that are
prone to wear and tear for timely replacement e.g., the waist and leg straps. In case of
necessary component/part replacement, contact customer service to get help.
Do not use potent detergents or any abrasive liquids to wipe down the surface for
maintenance. The surface should be dry before using the device.
It is forbidden to pour liquids on the shell of the device so as to avoid damage to its
electronic components or cause a safety hazard.
26
Frenquently Asked Questions (FAQ)
Q In-game directions are deviated on KAT Walk mini. What should I do?
A Deviation problem might have occurred due to a number of reasons. Please follow the
instructions below to identify, and solve the issue:
1)KAT I/O platform allows its users to perform a quick, manual calibration within VR. Just
click at the APP button on your controller, and select the calibration option.
2)Does the initialization process occur at startup? If not, please re-plug the device’s USB
connections, and try initializing it again.
3)Before the first use (or if you have recently relocated the device), please complete the
room setup, and directional calibration process.
4)When not in use, the leg straps might cause a minor interference. In order to solve this
issue, simply attach the straps to the corresponding support rods to prevent them from
swinging.
5)Please adjust the safety harness to your body, and tighten it up to avoid any loose space
between your back, and the back support.
Q It is not possible to move, or the motion is too slow on KAT Walk mini. What
should I do?
A Inability to walk or unnaturally slow motion might have occurred due to the following
reasons:
1)If you are unable to move forward within games, please check if Steam VR has been
initialized, and is working properly. Then, check if the connection between your headset,
and controllers has been established, and is functioning correctly. Try restarting Steam-
VR.
2)If you are unable to move within games, please check the status of KAT Walk mini in
KAT I/O. If its parameters are abnormal, re-plug the USB wire on mini’s interface. Then,
perform the initialization process, and restart SteamVR.
3)If walking is not available in Steam games, please make sure the controllers have been
turned on, and the game settings are correct.
4)If the walking speed seems abnormal, you can manually calibrate the speed parameter
in KAT IO Runtime up to the maximum speed set for the selected game.
27
Q What should I do if the installation process of KAT Walk mini has been correctly
accomplished but the supporting rods are not moving or are getting stuck.
A Please check if the rotation lock of the supporting rods has been unlocked. If the rods are
still not functioning properly, adjust the corresponding screw counterclockwise.
A A:1)Please check if the LED light’s DC, the power adapter, and the power cord are all
correctly plugged in.
2) Please check if the energy outlet is energized, and the power switch is turned on.
In case you have encountered any other problems, and need assistance in solving the
issues, please visit the relevant pages on our official website - http://katvr.com/sup-
port/technical-support/ or contact us at global@katvr.com
28
Appendix 1: Optional Accessories List
For a better experience, we also offer a variety of accessories that you can choose to match.
Hotline:400-826-0804 Sales Email:sales@katvr.com
Either-or
Including a cord
Cords organizers organizer and a
2
(Giveaway) screw hook for
each package
29
Optional Accessories List
KAT PiSystem
1 2 packages
Adapter
30
Appendix 2: KAT Control Center
KAT Control Center is available in two different variants ‒ Premium Version and Deluxe
Version ‒ with the latter one equipped with an HD LCD touch-screen that serves as a display
and control platform at the same time in order to enhance your VR experience. Using the
universal LCD screen allows you to follow the in-game experience of a player with no laten-
cy and easily operate the KAT I/O platform at the same time.
Product Introduction
Product Appearance
480mm
480
mm
590mm
1600mm
490mm 600mm
31
Product Parameters
CPU I5-7500
Motherboard B250
RAM 8G DDR4
Resolution 1920*1080
Product Weight 50 kg
Voltage 220 v
Powering 700 w
Note: There might be slight differences in the product parameters, please refer to what you have actually received.
32
Deluxe KAT Control Center
Product Introduction
Deluxe version of KAT Control Center uses a high-definition LCD touch-screen equipped
computer as a display and control platform. It integrates a high-performance computer, a
gaming platform and a business operation management system in order to improve and
facilitate the product’s commercial use.
Moreover, it is equipped with a 3D surround sound system and a large screen display to
enhance the VR experience ensuring highest level of customer satisfaction and maximizing
the merchants’ benefits.
Product Appearance
1035mm
935mm
590mm
1850mm
518mm 630mm
33
Product Parameters
OPTION A OPTION B
Product Weight 90 kg 90 kg
Note: There might be slight differences in the product parameters, please refer to what you have actually received.
34
List of Softwares
List of Softwares
Steam VR
Product Files
35
Product’
s maintenance and repairs
Do not unplug the device from the power source when it is powered on. Switch off the
interface frequently (except for the USB interface) to avoid the interface card from getting
burned or damaged.
Frequent use of hard disks, virus infection or even accidental misoperation may easily cause
important data loss. Remember about regular backups.
Should you find any problems with the equipment, do not postpone the necessary repairs for
later. All damage and malfunctions must be reported and repaired as soon as possible in
order to ensure that the device is always kept in a good working state.
Install relevant anti-virus software, update it regularly and frequently scan your system in
order to keep the device malware-free.
36
Frenquently Asked Questions (FAQ)
A You can find a folder entitled "KAT INSTRUCTION" at the desktop in which videos and
manuals are available. Since the manuels are to be updated, you can also download the
latest version at http://katvr.com/support/technical-support/
Q After booting the device as normal, BIOS detects the CPU, memory and disk
drive, but the screen displays“Keyboard error or no key board present”.
What should I do?
Q Till now I was able to use the keyboard and mouse without problems, until
they suddenly stopped working. What should I do?
37
Q After turning on the power switch, the device does not respond and the power
supply unit does not seem to be working properly. What should I do?
Q After booting the device, BIOS detects the CPU and memory as normal, but
the screen displays“Detecting IDE drives”for about 30 seconds (Normal time
should not exceed 5 seconds), and then it displays an error saying that the
hard disk was not found, and the computer can’t open the operating system.
What should I do?
If the malfunction stops at some point and the device enters its operating system as
normal, we strongly recommend you to create a backup for all of your important data.
When replacing the hard disk, please do not touch the components with your bare
hands to prevent damage caused by static electricity.
38
Q After turning on the device, BIOS detects the CPU, memory, hard drive and
keyboard normally, but the screen displays“cmos checksum error ‒ Defaults
loaded”. What should I do?
A The common cause of this problem is that the peripheral card’s resources conflict with
the BIOS, causing it to reset. Press the“del”button to enter the CMOS settings, then press
the F10 button, type“Y”and press Enter to restart the system.
Q When the device is powered up but the indicating light on passive backplane
just flash for one time, what should I do when the device quit working.
Q The computer turns on as normal, but keeps restarting before entering the
operating system desktop. What should I do?
39
Q The device used to work normally, but recently the software runs slower, and
sometimes it even crashes. What should I do?
40
Q The device is powered on, and the power supply unit works properly but the
computer does not respond. What should I do?
Q After the device is powered on, it does not start as normal, and I can hear a
continuous alarm sound.
A Please follow the steps below:
(1)Please check if the memory module is firmly fixed to the motherboard.
(2)Please check if the golden contact pins of the memory module are clean.
(3)Clean the golden contact pins of the memory module.
(4)Please try connecting the memory module to another memory slot on the motherboard.
(5)Use a replacement memory module and try turning on the computer again.
(6)Check if the hard RESET button is at its normal position and does not cause the malfunc-
tion. Otherwise, please restore the hard RESET button to its normal position.
41
Appendix 3: KAT PiSystem Adapter
Product Description
KAT PiSystem Adapter is a specialized adapter developed by KAT VR. It can synchronize the
motion in the VR headset with the actual movement by its user.
Power Port
1 2
Product Parameters
Please initialize the KAT Walk mini every time you use it.
42
Installation Instructions
Connect all cables prior plugging in power cord, in case of any potential hazards.
01
02
03
43
04
05
06
07
44
First Use Instructions
01
02
1-2 min
03
Controller connected.
Who is using this controller?
45
If adaption fails, unplug the power cord and
wait for five seconds.
04
46
Frequently Asked Questions (FAQ)
Q I’ve finished connecting all the cables but why doesn’t the button on the
controller work?
A Please press the PS button for adapting and pairing. If there is no response, please replug
the power cord and restart the KAT PiSystem Adapter.
A Every time you start PS4, please replug the power cord and restart the KAT PiSystem
Adapter.
A Reconnect the controller cable to KAT PiSystem Adapter and press the PS button for
adapting. If there is no response, please replug the power cord and restart the KAT
PiSystem Adapter.
47
Appendix 4: KAT Walk mni & Oculus Rift Connection
Instructions
KAT Walk mini can also work with Oculus Rift, but it requires some basic installation, connec-
tion and adjustment, here are the steps:
48
Installation Steps
01
03
04
49
05
06
Having finished the installation of
Oculus Rift, player can start the game.
In case the signal of headset or control-
ler gets lost, the angle of sensors can
be adjusted to capture all movements
in the game.
50
Appendix 5: Contact Information
Add:Room 901, Building 6, No 1818-2, West WenYi Road, Yuhang Street , Yuhang District,
Hangzhou, Zhejiang Province, China.
Postal code:311100
Tel:400-826-0804
E-mail:info@katvr.com
Web:http://www.katvr.com/
51
Version:201901