Professional Documents
Culture Documents
IntelligAIRE II Diagnostic Procedures Using Drivers Display Module
IntelligAIRE II Diagnostic Procedures Using Drivers Display Module
1 2 3 NOTE: Not all features may be available due to system NOTE: Service Test Mode is disabled if the lockup bit is set in
1. Press and hold for 3 seconds.
configuration or customer specifications. the configuration file.
4
NOTE: Setup Mode is disabled if the lockout bit is set in the The LED display will show ‘rtS’ for 1 second then will display the
actual return air temperature sensor reading for 2 seconds. The 1. Press and hold and for 3 seconds.
5 configuration file.
14 cycle will repeat continuously.
6
2. Press to scroll through menu selections.
7
1. Press and hold and for 3 seconds.
Digital Temperature Readout
13 Display
8 3. Press or once to start a test.
Digital Settings Description Default rtS Return Air Temperature
12 11 10 9 Display
4. Press to return to normal operation.
ctS Evaporator Coil Temperature
dEg F Unit of Temperature F
or (Fahrenheit or Celsius) dtS Discharge Air Temperature Display Service Test
Item Description C
cdS Compressor Discharge Temperature rt Relay Test - manually energizes each output.
1. 3-Digit Display PSI A Pressure Scale g
or (absolute or gauge) atS Ambient Air Temperature EF Evaporator Fan Test - manually control
2. Red LED Indicator - HEAT Mode evaporator fan speed 0 to 100%.
g
bcS Battery Cooler Coil Temperature
3. Blue LED Indicator - COOL Mode CF Condenser Fan Test - manually control
CC rh Clutch Control rh
or (reheat or cycling) utS Water Temperature condenser fan speed 0 to 100%
4. Zone 1 Indicator
Cy
CU Coolant Valve Test - manually control coolant
5. Zone 2 Indicator valve position 0 to 100%
SPH 62-82 F High Setpoint Limit 82
2. Press or to read additional sensors.
6. Zone 3 Indicator or dP Damper Test - manually control damper position
17-28 C 0 to 100%
7. Ambient Air Temperature Indicator 3. Press to view sensors in another zone.
SPL 62-82 F Low Setpoint Limit 62 Ft Functional Test - forces unit to operate in Cool,
8. Zone Select Key or Heat or Vent mode.
9. Setpoint Indicator
17-28 C PRESSURE READOUT MODE Pt Pre-Trip Test - automatically energizes each
output.
10. Down Arrow Key 1. Press and hold for 3 seconds.
2. Press or to change settings. The LED display will show ‘SP1’ for 1 second then will display the Relay Test - To start a relay test, select “rt” from the Service Test
11. Up Arrow Key menu and press Up or Down key. The display will show “r00” (all
actual suction pressure transducer 1reading for 2 seconds. The
relays off). Press the Up arrow key to advance to the next relay.
12. Percent Indicator cycle will repeat continuously.
Press the Down arrow key to back up to previous relay.
3. Press to scroll through menu selections.
13. On/Off Key
Digital Pressure Readout Display Relay Test
14. Alarm Indicator - Red or Yellow Display
4. Press to return to normal operation. r00 All relays are de-energized.
SP1 Suction Pressure 1 r01 Clutch output 1 energized.
r02 Clutch output 2 energized.
DP1 Discharge Pressure 1 r03 Evaporator high speed output energized.
r04 Evaporator medium speed output energized.
SP2 Suction Pressure 2
r05 Evaporator low speed output energized.
DP2 Discharge Pressure 2 r06 Condenser high speed output energized.
r07 Condenser low speed output energized.
r08 Boost pump output energized.
r09 Coolant valve output energized.
2. Press or to read additional transducers. r10 Liquid line valve output energized.
r11 Loading valve output 1 (bottom) energized.
r12 Loading valve output 2 (top) energized.
3. Press to view transducers in another zone.