Professional Documents
Culture Documents
Hearing Aid Circuit - Engineering Projects
Hearing Aid Circuit - Engineering Projects
ARDUINO PROJECTS IC 741 PROJECT IC 555 PROJECTS ELECTRONICS PROJECTS ELECTRICAL PROJECTS CONTACT ABOUT US
The hearing aid circuit available in the market are fully transistorized and generally use a
single pen cell. The hearing aid circuit uses an IC LM358 (IC1) for the same purpose which
give better sensitive and performance. You can also check DIY Hearing Aid Circuit using
555.
Circuit Description of
Hearing Aids Philippines Hearing Aid Circuit
Operational amplifiers are used
Hearing Test here in their simplest from non-
Sound Proof Booth inverting AC amplifier with a gain of
Categories
100. Op-amp A1 forms the first-
eardiagnostics.com.ph stage amplifier. Second-stage
amplification is given through op- 555 Timer Projects (66)
amp A2. Hence the total gain is 8051 Projects (12)
OPEN 10,000.
AC Voltage Stabilizer (6)
Resistors R1 and R2 provide biasing
alarm / sound generator (33)
to the condenser microphone, and
capacitor C1 is used for coupling. Finally, transistor T1 drives the earphones. Amplifier Circuit (26)
The circuit hearing aid is small enough to fit into a match-box as it uses only one IC and Antenna Fundamental (11)
very few discrete components. It is very sensitive and can pick even single weak signals Arduino Projects (83)
from a circular area of over ten meters diameter. The circuit hearing aid can also work as
a baby-phone by using a speaker instead of an ear-phone. ATmega Projects (11)
Automobile Engineering (8)
Automotive Circuit (7)
AVR Projects (8)
Basic Electronic Projects (48)
Hearpeers Battery Charger Circuit (14)
Start your hearing
OPEN
Bearing Capacity Theories (17)
journey now
C Based Project (18)
C++ Based Projects (5)
Civil Projects (121)
Cofferdams (3)
Computer Projects (24)
Conductor and Connection (1)
Resistors (all ¼-watt, ± 5% Carbon unless stated otherwise) Electronics Projects (423)
Electronics Troubleshooting (16)
R1 = 560 Ω
Field Effect Transistors (3)
R2 – R5 = 10 KΩ Geotechnical Process (7)
R6, R7 = 100 KΩ IC 741 Based Projects (34)
T1 = BC547 (General Purpose NPN Bipolar Junction Transistor) Numerical method Lab Manual (1)
Op amp Tutorials (10)
Miscellaneous
Oscillators and Signal Generators (2)
Hearpeers SW1 = On-Off Switch PIC Projects (4)
Start your hearing
OPEN
Piers and Caissons (7)
B1 = 3V Battery
journey now
Piled Foundation (15)
MIC1 = 34K8P Condenser Microphone
power supply (46)
Ear phones
Python (1)
RFID Projects (3)
Robotics (5)
Sheet Pile Wall (6)
Site Investigation (20)
Spread Foundation (9)
Switching and Controlling (41)
Tech (10)
Top 10 Electronics Projects (2)
Transistor Amplifiers (22)
Verified Preamplifier Circuit (16)
Employee Management
System Using C++
Employee Management
System Using C
Audiometric Test
Ad eardiagnostics.com.ph
Rangefinder Receivers
Ad analogmodules.com
you
Ad Hearpeers
Price
Ad icseek.com
Guitar Amplifier | Convert Hawain Guitar Sheet Pile Walls | Types of Sheet Pile Walls
to an Electric Guitar
Hüsnü Köktürk
October 30, 2014 at 3:03 am
excellent, well chosen schematics
Reply
Sevien Valencia
December 15, 2016 at 4:21 pm
How can i remove the hum sound in the hearing aid circuit? I’m only
using an electret mic.
Reply
Sevien Valencia
December 17, 2016 at 5:25 pm
How can i improve the range of sound, heard by the mic? I use electret
mic.
Reply
Dadab
April 14, 2017 at 1:22 am
I am trying to simulate this circuit using pspice, what can I put in place
of the microphone? And also, regarding A1 and A2, is +Vcc connected to 3v and -Vcc
to ground? Just making sure, thanks.
Reply
LEAVE A COMMENT
Comment
Hearpeers
Start your hearing
OPEN
journey now
Name
Website URL
ADD COMMENT
Recent Posts