Professional Documents
Culture Documents
Drill Pipe Configuration: 80 % Inspection Class
Drill Pipe Configuration: 80 % Inspection Class
Drill Pipe Configuration: 80 % Inspection Class
5-08
Drill Pipe Performance Sheet
www.NOV.com/GrantPrideco Phone: +1 (281) 878-8000 String No.:OWS-DP-TT550-01
Connection tensile at Recommended MUT is less than 80% inspection class pipe body tensile, a lower MUT should be considered.
Drill Pipe Configuration
Pipe Body OD (in)
740 Jnts. OWS-1001 to OWS-1741)
5.500
Pipe Body Wall Thickness (in) 0.415 Nominal Weight Designation 24.70
Pipe Body Grade S-135 Drill Pipe Approximate Length 31.9 (ft)
Connection Performance TurboTorque 550 ( 6.625 (in) OD X 4.250 (in) ID ) 130,000 (psi)
SmoothEdge Height Nominal Tool Joint Worn to Bevel Worn to Min TJ OD for
3/32 Raised OD Diameter API Premium Class
Box OD (in) 6.812 6.625 6.369 6.315
Elevator Capacity (lbs) 1,091,700 873,800 586,100 526,900
Note: Elevator capacity based on assumed Elevator Bore, no wear factor, and contact stress of 110,100psi.
Assumed Elevator Bore (in) 5.812 Note: A raised elevator OD increases elevator capacity without affecting make-up torque.
Pipe Body Slip Crushing Capacity Pipe Body Configuration ( 5.5 (in) OD 0.415 (in) Wall S-135 )
Nominal 80 % Inspection Class API Premium Class
Pipe Body Performance Pipe Body Configuration ( 5.5 (in) OD 0.415 (in) Wall S-135 )
Nominal 80 % Inspection Class API Premium Class
Pipe Tensile Strength (lbs) 895,000 704,300 704,300
Pipe Torsional Strength (ft-lbs) 101,800 79,800 79,800
TJ/PipeBody Torsional Ratio 0.83 1.06 1.06
80% Pipe Torsional Strength (ft-lbs) 81,500 63,800 63,800
Burst (psi) 17,826 16,298 16,298 Note: Nominal Burst
calculated at 87.5% RBW
Collapse (psi) 17,023 11,177 11,177 per API.
Pipe OD (in) 5.500 5.334 5.334
Wall Thickness (in) 0.415 0.332 0.332
Nominal Pipe ID (in) 4.670 4.670 4.670
Cross Sectional Area of Pipe Body (in^2) 6.630 5.217 5.217
Cross Sectional Area of OD (in^2) 23.758 22.346 22.346
Cross Sectional Area of ID (in^2) 17.129 17.129 17.129
Section Modulus (in^3) 7.844 6.145 6.145
Polar Section Modulus (in^3) 15.688 12.290 12.290
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully
responsible for the accuracy and suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied
warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear
conditions (remaining body wall) is for information only and does not represent or imply acceptable operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance
ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box ID’s, tool joint ID refers to
the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
www.NOV.com/GrantPrideco/CustomerFeedback Steven Youngson 09-19-2011
Connection TurboTorque 550 Tool Joint OD (in) 6.625 Tool Joint ID (in) 4.250 Tool Joint Specified Minimum 130,000
Yield Strength (psi)
Pipe Body 80 % Inspection Class Pipe Body OD (in) 5.5 Wall Thickness (in) 0.415 Pipe Body Grade S-135
(ft-lbs) (ft-lbs)
Connection
Make-up Torque Range
Connection Max
(ft-lbs) Tension (lbs)
Note: Recommended MUT should always be used when possible. If not possible, MUT should be as close to Recommended MUT as possible.
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box ID’s, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
Connection
Wear
Tool Connection Rec MUT Connection Max Min MUT Connection Max
Torsional Tension Tension
New OD Joint OD
(in) Strength (ft-lbs) (ft-lbs) (lbs) (ft-lbs) (lbs)
6.625 84,800 59,300 634,100 42,400 1,038,600
6.597 84,700 59,300 630,700 42,400 1,043,300
6.569 84,700 59,300 627,200 42,300 1,045,800
6.54 84,600 59,200 626,100 42,300 1,042,200
6.512 83,500 58,500 639,700 41,800 1,043,800
6.484 81,600 57,100 670,200 40,800 1,024,100
6.456 79,700 55,800 698,000 39,900 1,006,800
6.428 77,900 54,500 725,500 38,900 987,000
6.4 76,000 53,200 752,600 38,000 969,600
6.371 74,100 51,900 779,200 37,000 949,800
Worn OD 6.343 72,200 50,600 805,700 36,100 932,300
6.315 70,400 49,300 831,700 35,200 914,800
Pipe Body
Combined Loading Table (Torque-Tension)
Pipe Body 80 % Inspection Class Pipe Body OD (in) 5.5 Wall Thickness (in) 0.415 Pipe Body Grade S-135
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box ID’s, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
1,200,000
Pipe Body in Combined Loading
Pipe Body Yield at 80%
Inspection Class
1,000,000
Connection Performance (based on MUT)
Tool Joint Yield
Tool Joint Shoulder Separation
800,000 TJ Operational Limit (Rec MUT)
TJ Operational Limit (Min MUT)
Tension (lbs)
600,000
400,000
200,000
Torque (ft‐lbs)
Drill Pipe Operational Limits (Connection at Recommended MUT = 59,300 (ft-lbs) )
Connection: TurboTorque 550 (6.625 (in) OD X 4.250 (in) ID) SMYS = 130,000 (psi)
Pipe Body: 80% Inspection Class, 5.500 (in) OD, 0.415 (in) wall thickness, S‐135 Pipe Grade
700,000
Overload Zone
600,000
500,000
Tension (lbs)
400,000
Operational limit (safety factor = 1.0)
300,000
200,000
100,000
Operational Torque (ft‐lbs)
Drill Pipe Operational Limits (Connection at Minimum MUT = 42,400 (ft-lbs) )
Connection: TurboTorque 550 (6.625 (in) OD X 4.250 (in) ID) SMYS = 130,000 (psi)
Pipe Body: 80% Inspection Class, 5.500 (in) OD, 0.415 (in) wall thickness, S‐135 Pipe Grade
800,000
Overload Zone
700,000
600,000
500,000
Tension (lbs)
400,000
Operational limit (safety factor = 1.0)
300,000
200,000
100,000
Operational Torque (ft‐lbs)
Connection Wear for TurboTorque 550 (6.625 (in) OD X 4.250 (in) ID)
Material SMYS (specified minimum yield strength) = 130,000 (psi)
90,000
80,000
70,000
60,000 Connection
Torsional Strength
Torque (ft‐lbs)
Recommended MUT
50,000
Minimum MUT
40,000
Pipe Body
30,000 80% of Premium Pipe
Body Torsional Strength
Pipe Body: 5.500 (in) OD, 0.415 (in) wall
thickness, S‐135 Pipe Grade
20,000
10,000
Tool Joint OD (in)