Professional Documents
Culture Documents
MW2 Writeups
MW2 Writeups
12. Set the gear according to the required pitch of 2 mm as per the table was given
On the lathe machine.
13. By using V-shape threading tool and Perform the external thrcading operation.
Precaution:
1. Workpiece should be firmly gripped in the three jaw chuck.
2. Coolant is to be used.
3. Apron, safety goggle & safety footwear must be used while working.
4. Proper rpm should be selected bcfore the operation.
B.TECH (INTG) SEM V MACHINE SHOPI PRACTICAL 2022-2023
TITLE: J0B-1 TO PERFORM VARIOUS OPERATIONS ON LATHE MACHINE
-CHF 2X45° CHF 2X45
M30 X2MM PITCH
EXPERIMENT NO: 02
0OB-2 TO MAKE AN INTERNAL THREADING ON LATHE MACHINE)
Aim: To prepare a job on lathe machine involving facing, External turning, drilling
internal threading.
Tool Required: Single point cutting tool, center dril, 1Smm drill, 25mm drill, and boring
bar
Procedure:
1. Take raw material of diameter 40mm and length 30mm of mild steel material.
2.3. Make diameter 38mmthroughout the length.
Perform facing operation on both the surfaces and maintain a length 25mm.
4. Perform the chamfering operation on both the edges of the job.
5. Make a center point on any one face.
6. Perform a drilling operation of diameter 1Smm & 25mm from the marked point,
throughout the job.
7. Match the gear setting according to the required pitch of 2 mm as per the table given
On the lathe machine.
8. Do the internal threading operation by using Internal "v" Threading Tool.
Precaution:
I. Workpiece should be firmly gripped in the three jaw chuck.
2. Coolant is to be used.
3. Apron, safety goggle & safety footwear must be used while working.
4. Proper rpm should be selected before the operation.
B.TECH (INTG) SEM V MACHINE SHOP II PRACTICAL 2022-2023
TITLE: J08-2 TO MAKE AN INTERNAL THREADING ON LATHE MACHINE
CHF 2X45°
==
-25
NMIMS IvTRT
TECHNOLOGY MANAGEMENT
& ENGINEERING
EXPERIMENT NO: 03
TURNING ON LATHE MACHINE)
JOB-3 TO MAKE AN INTERNAL TAPER
cutting tool, center drill, ISmm drill, 25mm dril, and boring
Tool Required: Single point
ar
040 2Smm
Material Regquired: Mild steel rod size:
x
Procedure:
Take material length
of diameter 40mm and 25mm of mild steel material.
I. raw
Precaution:
I. Workpicce should be firmly gripped in the three jaw chuck.
2. Coolant is to be uscd.
3. Apron, safety goggle & safety footwear must be used while working.
4. Proper rpm should be selected before the operation.
B.TECH (INTG) SEM V MACHINE SHOP II PRACTICAL 2022-2023
TITLE :308-3 TO MAKE AN INTERNAL TAPER TURNING ON LATHE MACHINE
20
EXPERIMENT NO: 04
(JOB-4 TO MAKE AN INTERNAL BORING ON LATHE MACHINE)
Machine &Tools Required: Band Saw, Lathe Machine, Steel rule, Vernier caliper etc.
Procedure
1. Take raw material of diameter 40mm and length 30mm of mild steel material.
2. Make diameter 38mm throughout the length.
3. Perform facing operation on both the surfaces and maintain a length 25mm.
4. Perform the chamfering operation on both the cdges of the job.
5. Make a center point on any once tacc.
6. Perform a drilling operation of diameter I5mm & 25mm from the marked point,
throughout the job.
7. Perform the intemal boring operation by using boring bar with 'V" shape tool and
maintain a diameter 30mm.
Precaution:
in the three jaw chuck.
1.Workpiece should be firmly gripped
2. Coolant is to be used.
used while
3. Apron, & must
safety goggle safety footwear
4. Proper rpm should be selected before the operation.
be working
B.TECH (INTG) SEM V MACHINE SHOPII PRACTICAL 2022-2023
MACHINE
TITLE :JOB 4 TO MAKE AN INTERNAL BORING ON LATHE
PCHF 2X45°