Professional Documents
Culture Documents
Jaurigues Audit Report Midterm
Jaurigues Audit Report Midterm
Jaurigues Audit Report Midterm
BS Mechanical Engineering
ME 302 - ME Elective 2
LAGUNA UNIVERSITY
Laguna Sports Complex, Bubukal Santa Cruz, 4009, Laguna
Submitted by:
Ferma, Idmarck
Rebong, Pauline Joy
Piamonte, Joseph Michael
Robles, Kenneth
Salcedo, Jonard
Submitted to:
Engr. Gaious Joe L. Bautista, RME
October 2022
Table of Contents
1. INTRODUCTION ........................................................................................................ 1
1.1 Objectives................................................................................................................. .1
I
College of Engineering
II
BS Mechanical Engineering
2. INTERPRETATION ...........................................................................................…….. 1
3. SUMMARY OF RECOMMENDATIONS........................................................................2
3.1 Description of building ..........................................................................................…..3
3.2 Findings................................................................................................................……5
4. HISTORICAL DATA ANALYSIS ..........................................................................….... 8
4.1 Energy Balance ..............................................................................................…….... 8
APPENDIX C Inventory of all appliances………………….………………………………...9
APPENDIX D Inventory for Door(s)/Window(s)/Room(s)
………………………………………………………………….11
APPENDIX E Computation of Power Consumption Monthly …………………………….12
APPENDIX F Additional Photos / Documentation ………………………………………….13
II
College of Engineering
1
BS Mechanical Engineering
1. INTRODUCTION
1.1 Objectives
The Energy Audit was defined to meet the following objectives:
• Find out what can be done to lower energy use across the board and, if money is
available, what system improvements are feasible.
• Carry out a quick walk-through audit or observation of the energy consumption of the
electrical equipment at the Perferio Jaurigue’s Residence building.
• Identify and evaluate potential tactics for enhancing the buildings'/wards'
environmental performance and offer remedies.
2 . INTERPRETATION
In this report, unless the contrary intention appears;
Energy conservation refers to actions done to decrease and consume as little energy as possible
through adjusting energy consumption behavior, for example. When not in use, turn off lights.
Energy efficiency is defined as utilizing less energy to produce the same service/output, for example.
Changing out inefficient light bulbs for efficient ones.
Faulty meaning that the equipment is not operating properly or was not installed appropriately.
Potential savings refer to the actual decrease in operating expenditures resulting from better energy
efficiency created by an energy conservation or efficiency activity.
Retrofitting is the process of improving the energy efficiency of an existing system.
Tariff refers to the amount of money charged by the supplier (utility) for the usage of electrical
energy per kWh.
3. SUMMARY OF RECOMMENDATIONS
The following are some suggestions based on general observations made across the Perferio
Jaurigue's Residence building.
The recommendations are classifed, with A being the most urgent, requiring immediate action (first
or second week of receiving this report). B might be 1 to 2 months after obtaining this report, whereas
C is dependent on funding availability.
1
College of Engineering
2
BS Mechanical Engineering
Table: Recommendations
Recommendations
Category A Category B Category C
Faulty air conditioners are Dispose of any broken Put energy saving measures
found inside the residence equipment inside the structure. into action, isolate or
(they may be operating, but no disconnect vampire loads
cold air is being expelled), while not in use.
isolate or disconnect them, or
get the air conditioners
serviced once every three
months.
Remove the air conditioner if In places, where air Create internal energy-
the room is truly not properly conditioning is not necessary, saving and efficiency
sealed. use fans. measures for the building.
Replace obsolete outdoor air Techniques for reducing Any incandescent light bulb
conditioners with more energy use include efficiency should be replaced as
efficient ones and conservation initiatives. necessary across the whole
structure. Reduce the number
of lights in each area or get rid
of any that are unnecessary.
Observation: Perferio Jaurigue's Residence Building is constructed in a modern style. The wiring and
electrical outlets were nicely structured, and the electrical system was decent and well-located so that
appliances could be used effectively.
Suggestion: When not in use, please plugged off the appliances to avoid high consumption of power.
Suggestion: The appliances should turn off when not needed, that may result to high cost of electrical
consumption.
2
College of Engineering
3
BS Mechanical Engineering
3.2 FINDINGS
3
College of Engineering
4
BS Mechanical Engineering
3.2.2 Lighting
The most frequent load in both indoor and outdoor spaces is lighting. Below are a few
the following features and flaws were found:
i. Findings of lightnings
Issues/Observation
- There are too many lights connected to one switch.
- Based on our observations, there are too many unnecessary lights in a room that
consumpt too much energy.
Recommendations
- To better manage illumination, reduce the number of lights per switch.
- Decrease the quantity of lights in each space.
- When not in use, turn off the lights.
4
College of Engineering
5
BS Mechanical Engineering
Issues/Observation
- When entering and leaving the room where the air conditioner is, person in the room leave
the door open.
- The airconditioner's brand and model are inconsistent (not inverter type), which
makes maintenance expensive.
- The doors and windows they used in an air- conditioning room is highly advisable.
Recommendations
- When entering or leaving an air-conditioned room, always shut the door.
- Turn off while not in use, but don't lower the temperature, and keep it on.
- In the event that the air conditioner is not running, try to get some fresh air outside
entirely to reduce the price of electricity.
- At least two or three maintenance visits should be made to every installed air conditioner.
- When possible, switch to an electric fan.
5
College of Engineering
6
BS Mechanical Engineering
OCTOBER
6
College of Engineering
7
BS Mechanical Engineering
Turbo 1 1200 W
7
College of Engineering
8
BS Mechanical Engineering
8
College of Engineering
9
BS Mechanical Engineering
9
College of Engineering
10
BS Mechanical Engineering
WINDOW -
DIMENSION/AREA
Side 1 = 3.25 x 2.60 = 8.45 m^2
Side 2 = 3.25 x 2.60 = 8.45 m^2
Side 3 = 2.55 x 2.60 = 6.63 m^2
Side 4 = 2.55 x 2.60 = 6.63 m^2
Roof = 3.25 x 2.55 = 8.2875 m^2
Floor = 3.25 x 2.55 = 8.2875 m^2
A. Transmission Load
BEDROOM 1
Walls and Roof
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 26.629 m^2 x (32C - 21C) x 24 ÷ 1000
Q = 3.866 kWh/Day
Floor
Q = 0.55 x 8.2875 m^2 x ( 32C - 21C) x 24 ÷ 1000
Q = 1.2033 kWh/Day
Total daily transmission heat gain = 3.866 + 1.2033 = 5.0693 kWh/Day
10
College of Engineering
11
BS Mechanical Engineering
11
College of Engineering
12
BS Mechanical Engineering
12
College of Engineering
13
BS Mechanical Engineering
13
College of Engineering
14
BS Mechanical Engineering
Q = 6.090 kWh/Day
Floor
Q = 0.55 x 8.2875 x ( 32 - 20 ) x 24 / 1000
Q = 1.312 kWh/Day
Total daily transmission heat gain = 6.090 + 1.312 = 7.402 kWh/Day
Internal heat load – People
Q = people x time x heat / 1000
Q = 3 x 9 x 150 / 1000
Q = 4.05 kWh/Day
Internal heat load – Lighting
Q= lamps x time x wattage / 1000
Q = 6 x 10 x 6 / 1000
Q = 0.36 kWh/Day
Equipment load – fan motors
Q = fans x time x wattage / 1000
Q = 2 x 15 x 65 / 1000
Q = 1.95 kWh/Day
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 10 x 17.5 x 1.2 x (32C - 20) / 3600
Q = 0.7 kWh/ Day
Total cooling load
Transmission load: 7.402 kWh/Day
Internal load: 4.41 kWh/Day
Equipment load: 1.95 kWh/Day
Infiltration load: 0.7 kWh/ Day
TOTAL = 14.462 kWh/Day
14
College of Engineering
15
BS Mechanical Engineering
DAY 2
BEDROOM
Walls and Roof
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 26.625 x ( 30 - 19 ) x 24 / 1000
Q = 3.8659 kWh/Day
Floor
Q = 0.55 x 4.425 x ( 30 - 19 ) x 24 / 1000
Q = 0.6425 kWh/Day
Total daily transmission heat gain = 3.8659 + 0.6425 = 4.5084 kWh/Day
Internal heat load – People
Q = people x time x heat / 1000
Q = 4 x 8 x 200 / 1000
Q = 6.4 kWh/Day
Internal heat load – Lighting
Q= lamps x time x wattage / 1000
Q = 6 x 8 x 6 / 1000
Q = 0.288 kWh/Day
Equipment load – fan motors
Q = fans x time x wattage / 1000
Q = 2 x 8 x 65 / 1000
Q = 1.04 kWh/Day
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 10 x 15 x 1.2 x ( 30 - 19 ) / 1000
Q = 1.98 kWh/Day
Total cooling load
15
College of Engineering
16
BS Mechanical Engineering
16
College of Engineering
17
BS Mechanical Engineering
17
College of Engineering
18
BS Mechanical Engineering
18
College of Engineering
19
BS Mechanical Engineering
19
College of Engineering
20
BS Mechanical Engineering
20
College of Engineering
21
BS Mechanical Engineering
Floor
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 4.7 x (33-21) x 24 / 1000
Q = 4.061 kWh/Day
Total daily transmission heat gain = 15.336 + 4.061 = 19.3968 kWh/Day
Internal heat load – People
Q = people x time x heat / 1000
Q = 3 x 8 250 / 1000
Q = 6 kWh/Day
Internal heat load – Lighting
Q= lamps x time x wattage / 1000
Q = 6 x 10 x 6 / 1000
Q = 0.36 kWh/Day
Equipment load – fan motors
Q = fans x time x wattage / 1000
Q = 2 x 8 x 65 / 1000
Q = 1.04 kWh/Day
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 10 x 15 x 1.2 x (33-21) / 3600
Q = 0.9kWh/Day
Total cooling load
Transmission load = 19.3968 kWh/Day
Internal load = 6.63 kWh/Day
Equipment load = 1.04 kWh/Day
Infiltration load = 0.9 kWh/Day
TOTAL = 27.9668 kWh/Day
21
College of Engineering
22
BS Mechanical Engineering
SALA
Transmission Load
Walls and Roof
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 31.9925 x ( 33-21) x 24 / 1000
Q = 5.0676 kWh/Day
Floor
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 6.4925 x ( 33-21) x 24 / 1000
Q = 1.0284 kWh/Day
Total daily transmission heat gain = 5.0676 + 1.0284 = 6.0960 kWh/Day
Internal heat load – People
Q = people x time x heat / 1000
Q = 3 x 8 250 / 1000
Q = 6 kWh/Day
Internal heat load – Lighting
Q= lamps x time x wattage / 1000
Q = 6 x 10 x 6 / 1000
Q = 0.36 kWh/Day
Equipment load – fan motors
Q = fans x time x wattage / 1000
Q = 2 x 8 x 65 / 1000
Q = 1.04 kWh/Day
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 10 x 15 x 1.2 x (33-21) / 3600
Q = 0.9kWh/Day
22
College of Engineering
23
BS Mechanical Engineering
23
College of Engineering
24
BS Mechanical Engineering
Q = 2 x 8 x 65 / 1000
Q = 1.04 kWh/Day
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 10 x 15 x 1.2 x (33-21) / 3600
Q = 0.9kWh/Day
Total cooling load
Transmission load = 48.411 kWh/Day
Internal load = 6.63 kWh/Day
Equipment load = 1.04 kWh/Day
Infiltration load = 0.9 kWh/Day
TOTAL = 56.711 kWh/Day
DAY 4
Bedroom
Transmission load
Walls and Roof
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 26.629 x (33-22) x 24 / 1000
Q = 3.866kWh/Day
Floor
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 4.425 x ( 33-22) x 24 / 1000
Q = 0.64251 kWh/Day
Total daily transmission heat gain = 3.866+ 0.64251 = 4.5085 kWh/Day
Internal heat load – People
Q = people x time x heat / 1000
Q = 2 x 5 x 250 / 1000
24
College of Engineering
25
BS Mechanical Engineering
Q = 2.5 kWh/Day
Internal heat load – Lighting
Q= lamps x time x wattage / 1000
Q = 6 x 5 X 6 / 1000
Q = 0.18 kWh/Day
Equipment load – fan motors
Q = fans x time x wattage / 1000
Q = 2 x 5 x 65 / 1000
Q = 0.65 kWh/Day
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 10 x 15 x 1.2 x ( 33-22)/ 3600
Q = 0.55 kWh/Day
Total cooling load
Transmission load = 4.5085 kWh/Day
Internal load = 2.68 kWh/Day
Equipment load = 0.65 kWh/Day
Infiltration load = 0.55 kWh/Day
TOTAL = 8.3885 kWh/Day
Sari-Sari Store
Transmission Load
Walls and Roof
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 17.75 x ( 33-22) x 24 / 1000
Q = 2.5773 kWh/Day
Floor
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
25
College of Engineering
26
BS Mechanical Engineering
26
College of Engineering
27
BS Mechanical Engineering
27
College of Engineering
28
BS Mechanical Engineering
28
College of Engineering
29
BS Mechanical Engineering
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 10 x 15 x 1.2 x ( 33-22)/ 3600
Q = 0.55 kWh/Day
Total Cooling load
Transmission load =6.785 kWh/Day
Internal load = 10.076 kWh/Day
Equipment load = 1.43 kWh/Day
Infiltration load = 0.55 kWh/Day
TOTAL = 18.841 kWh/Day
DAY 5
BEDROOM
Transmission load
Walls and Roof
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 26.629 x ( 34-20 ) x 24 /1000
Q = 4.9210 kWh/Day
Floor
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 4.425 x ( 34-20) x 24 / 1000
Q = 0.8177 kWh/Day
Total daily transmission heat gain = 5.7387 kWh/Day
Internal heat load – People
Q = people x time x heat / 1000
Q = 2 x 10 x 200 / 1000
Q = 4 kWh/Day
Internal heat load – Lighting
29
College of Engineering
30
BS Mechanical Engineering
30
College of Engineering
31
BS Mechanical Engineering
31
College of Engineering
32
BS Mechanical Engineering
32
College of Engineering
33
BS Mechanical Engineering
33
College of Engineering
34
BS Mechanical Engineering
34
College of Engineering
35
BS Mechanical Engineering
Q = 0.252 kWh/Day
Equipment load – fan motors
Q = fans x time x wattage / 1000
Q = 2 x 7 x 65 /1000
Q = 0.91 kWh/Day
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 12 x 16 x 1.5 x ( 31-19) /3600
Q = 192.018kWh/Day
Total Cooling load
Transmission load = 4.9189kWh/Day
Internal load = 5.082 kWh/Day
Equipment load = 0.91 kWh/Day
Infiltration load = 192.018 kWh/Day
TOTAL = 202.92 kWh/Day
SARI-SARI STORE
Transmission load
Walls and Roof
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 17.75 x ( 31-19) x 24 /1000
Q = 2.8116 kWh/Day
Floor
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 4.425 x ( 31-19) x 24 /1000
Q = 0.7009 kWh/Day
Total daily transmission heat gain = 3.5125 kWh/Day
Internal heat load – People
35
College of Engineering
36
BS Mechanical Engineering
36
College of Engineering
37
BS Mechanical Engineering
Floor
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q =0.55 x 6.4925 x ( 31-19) x 24 / 1000
Q = 1.0284 kWh/Day
Total daily transmission heat gain = 6.096 kWh/Day
Internal heat load – People
Q = people x time x heat / 1000
Q = 3 x 7 x 230 / 1000
Q = 4.83 kWh/Day
Internal heat load – Lighting
Q = lamps x time x wattage / 1000
Q = 6 x 7 x 6 / 1000
Q = 0.252 kWh/Day
Equipment load – fan motors
Q = fans x time x wattage / 1000
Q = 2 x 7 x 65 /1000
Q = 0.91 kWh/Day
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 12 x 16 x 1.5 x ( 31-19) /3600
Q = 192.018kWh/Day
Total Cooling load
Transmission load = 6.096kWh/Day
Internal load = 5.082 kWh/Day
Equipment load = 0.91 kWh/Day
Infiltration load = 192.018 kWh/Day
TOTAL = 204.106 kWh/Day
37
College of Engineering
38
BS Mechanical Engineering
KITCHEN
Transmission load
Walls and Roof
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 38.4475x (31-19)x 24 /1000
Q = 6.0901 kWh/Day
Floor
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 8.2875 x ( 31-19) x 24 / 1000
Q = 1.3127 kWh/Day
Total daily transmission heat gain = 7.4028 kWh/Day
Internal heat load – People
Q = people x time x heat / 1000
Q = 3 x 7 x 230 / 1000
Q = 4.83 kWh/Day
Internal heat load – Lighting
Q = lamps x time x wattage / 1000
Q = 6 x 7 x 6 / 1000
Q = 0.252 kWh/Day
Equipment load – fan motors
Q = fans x time x wattage / 1000
Q = 2 x 7 x 65 /1000
Q = 0.91 kWh/Day
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 12 x 16 x 1.5 x ( 31-19) /3600
Q = 192.018kWh/Day
38
College of Engineering
39
BS Mechanical Engineering
39
College of Engineering
40
BS Mechanical Engineering
40
College of Engineering
41
BS Mechanical Engineering
41
College of Engineering
42
BS Mechanical Engineering
Q = 1.2855 kWh/Day
Total daily transmission heat gain = 7.6200 kWh/Day
Internal heat load – People
Q = people x time x heat / 1000
Q = 2 x 7 x 200 /1000
Q = 2.8 kWh/Day
Internal heat load – Lighting
Q = lamps x time x wattage / 1000
Q = 6 x 7 x 6 / 1000
Q= 0.252 kWh/Day
Equipment load – fan motors
Q = fans x time x wattage / 1000
Q = 2 x 7 x 65 /1000
Q = 0.91 kWh/Day
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 11 x 15 x 1.2 x ( 33-18) /3600
Q = 0.825 kWh/Day
Total Cooling load
Transmission Load = 7.6200 kWh/Day
Internal Load = 3.052 kWh/Day
Equipment load = 0.91 kWh/Day
Infiltration load = 0.825 kWh/Day
TOTAL = 12.407 kWh/Day
KITCHEN
Transmission load
Walls and Roof
42
College of Engineering
43
BS Mechanical Engineering
43
College of Engineering
44
BS Mechanical Engineering
44
College of Engineering
45
BS Mechanical Engineering
45
College of Engineering
46
BS Mechanical Engineering
46
College of Engineering
47
BS Mechanical Engineering
Q = 12 kWh/Day
Internal heat load – Lighting
Q = lamps x time x wattage / 1000
Q = 6 x 12 x 65 / 1000
Q = 4.68 kWh/Day
Equipment load – fan motors
Q = fans x time x wattage / 1000
Q = 2 x 12 x 65 / 1000
Q = 1.56 kWh/Day
Infiltration load
Q = changes x volume x energy x (Temp out – Temp in ) / 3600
Q = 12 x 15 x 1.2 x ( 35-23) /3600
Q = 0.72 kWh/Day
Total Cooling load
Transmission Load = 6.1645 kWh/Day
Internal load = 16.68 kWh/Day
Equipment load = 1.56 kWh/Day\
Infiltration load = 0.72 kWh/Day
TOTAL = 25.1245 kWh/Day
KITCHEN
Transmission Load
Walls and Roof
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
Q = 0.55 x 38.4475 x ( 35-23) x 24 /1000
Q = 6.0900 kWh/Day
Floor
Q = U x A x (Temp out – Temp in) x 24 ÷ 1000
47
College of Engineering
48
BS Mechanical Engineering
48
College of Engineering
49
BS Mechanical Engineering
49
College of Engineering
50
BS Mechanical Engineering
October 1
50
College of Engineering
51
BS Mechanical Engineering
51
College of Engineering
52
BS Mechanical Engineering
October 2
52
College of Engineering
53
BS Mechanical Engineering
October 4
October 7
October 9
53
College of Engineering
54
BS Mechanical Engineering
Octoberer 12
54
College of Engineering
55
BS Mechanical Engineering
October 14
October 15
55