Professional Documents
Culture Documents
Watertite PU 20
Watertite PU 20
CHARACTERISTICS
► Highly durable and UV stable
► Excellent abrasion resistance
► Good chemical resistance
► Can be applied to many different substrates and on
cured epoxy systems
TDS_Watertite PU 20_GCC_0519
► Excellent glossy surface finish with different colors
► Easy to apply
DESCRIPTION
Watertite PU 20 is a 2 component UV stable polyurethane
protective coating system. The coating provides a seamless 1
chemical and abrasion resistant coating to cured epoxy
systems, metal and concrete surfaces both internal and
Metal Surfaces: Surface should be sand blasted or should
external.
be manually or mechanically sanded get a rust free finish. If
Fields of application necessary prime the surface with Polyprime EPS.
Watertite PU 20 is designed as a protective and wear Fully Cured Epoxy Surface: Clean the surface thoroughly,
resistant coating for new and existing trafficked areas such remove dust or any oil which is left on the surface and
as: directly apply
NOTE:-Primers should be completely dry before applying
– Sewage works / Effluent treatment plants
Watertite PU 20
– Chemical processing areas.
– Concrete floors / Factory ware houses. Priming
Prime the surface with Polyprime EP (Solvent free 100%
– Bridge and culvert decks
solid epoxy primer @ 4-5 m2/kg) depending on the
– Swimming pool decks. substrate condition.
– Jetties, harbors.
Mixing
– Stadiums, balconies & plant rooms.
Mix both parts of Watertite PU 20 thoroughly for a few
– Factory warehouses minutes to remove any sediment. Then add the contents of
application instructions Part B to Part A and mix with a suitable paddle mixer fitted
to a slow speed electric drill. The mixing is to be continued
Surface Preparation till a uniform and homogenous consistency is achieved.
Concrete Surfaces: The concrete surface to be coated Application
must be clean, dry and free of laitance, oil, grease or any The material can be applied with a brush, roller. Apply the
substance that may impair adhesion. Methods of substrate mixed material @ 120 to 150 micron WFT. If required a
preparation includes, grit blasting, highpressure water jet second coat can be applied at right angles to the first coat
cleaning, surface grinding etc. Weak or damaged concrete at the same coverage rate. For getting an anti skid finish,
must be removed and repaired properly with Polypoxy NF. broadcast Aggregate no. 8 @ 0.5 to 1.2 kg/m² on the wet
primer. Leave it for 24 hours and then when the primer has TECHNICAL PROPERTIES
fully set, brush/vacuum away the excess aggregate from the
surface. Apply the top coat as specified. Pot life @25°C [min] 30 to 40
Density [g/cc] 1.2
COVERAGE
Solid content [%] 65
Primer : 4-5 m²/L
Aggregate No. 8 : 0.5 -1.2 kg. /m² Pendulum hardness [sec] 73
Watertite PU 20 : 4-5 m²/L/coat. Abrasion resistance [mg] 50
(ASTM-D-4060) I0 N load,
Supply 1000 cycles, CS 10 roller
Primer : 5L Touch dry @25°C [hrs] 4
Aggregate no. 8 : 25 kg bag. Re-coatable [hrs] 24
Watertite PU 20 : 15L
Full cure [days] 7
CLEANING Color grey
Clean all the tools with Polysolvent immediately after use. (other colors on request)
Hardened materials can be removed mechanically only. Resistance to dilute acids, alkalis, solvent,
starch solution and milk.
STORAGE & SHELF LIFE
Application thickness 120-150
Store in a cool dry and shaded place. Protect from extreme
WFT /Coat (i.e. 70 to 95
weather conditions like storm & rain. The shelf life will be
micron DFT/ Coat) [microns]
6 Months out of contact with moisture at standard storage
conditions. Coverage [m2/L] 6-8 depending on the
surface finish.
TDS_Watertite PU 20_GCC_0519