Professional Documents
Culture Documents
ZW250
ZW250
GENERAL
―CONTENTS―
Group 1 Specifications Group 3 Component Specifications
Specifications ........................................... T1-1-1 Engine ...................................................... T1-3-1
Engine Accessories .................................. T1-3-6
Group 2 Component Layout
Hydraulic Component ............................... T1-3-8
Main Component Layout........................... T1-2-1
Electrical Component.............................. T1-3-13
Electrical Component Layout.................... T1-2-4
(Overview)
Electrical System (Cab) ............................ T1-2-5
Electrical System .................................... T1-2-6
(Controller and Relays)
Electrical System (Right Console) ............ T1-2-7
Electrical System (Monitor and Switchs)... T1-2-8
Monitor Panel ........................................... T1-2-9
Engine and Fan Pump ............................ T1-2-10
Pump Device and Drive Unit....................T1-2-11
Control Valve .......................................... T1-2-12
Ride Control Valve,Charging Block
and Fan Motor ................................... T1-2-13
Steering Valve and Emergency Steering
Pump (Optional) .................................. T1-2-14
4GCT-1-1
(Blank)
4GCT-1-2
GENERAL / Specification
SPECIFICATIONS
M4GB-12-002
T1-1-1
GENERAL / Specification
(Blank)
T1-1-2
GENERAL / Component Layout
MAIN COMPONENT LAYOUT (OVERVIEW)
1 2 3 4 PHOTO
Overview
5
001
12
11
10
T4GB-01-02-005
T1-2-1
GENERAL / Component Layout
MAIN COMPONENT LAYOUT (UPPERSTRUCTURE)
PHOTO
Overview
002
1 2 3 4 5
21
20
19
18
17
16
15
8
9
10
14 13 12 11
T4GB-01-02-002
T1-2-2
GENERAL / Component Layout
MAIN COMPONENT LAYOUT (TRAVEL SYSTEM)
PHOTO
Overview
1
2 003
3
7
T4GB-01-02-004
T1-2-3
GENERAL / Component Layout
ELECTRICAL COMPONENT LAYOUT (OVERVIEW)
Cab
(Refer to T1-2-5)
1 2
11
12 Engine and Fan Pump
(Refer to T1-2-10)
10
7
8
Pump Device
(Refer to T1-2-11)
9 Drive Unit
(Refer to T1-2-11)
T4GB-01-02-019
1 - Hydraulic Oil Level Switch 4 - Reverse Buzzer 7 - Fuel Level Sensor 10 - Bucket Proximity Switch
2 - Air Filter Restriction Switch 5 - Battery 8 - Hydraulic Oil Temperature 11 - Lift Arm Proximity Switch
Sensor
3 - ECM 6 - Boost Pressure Sensor 9 - Lift Arm Angle Sensor
(Optional)
T1-2-4
GENERAL / Component Layout
ELECTRICAL SYSTEM (CAB)
1
2
Right Consol
(Refer to T1-2-7)
T4GB-01-02-006
T1-2-5
GENERAL / Component Layout
Controller and Relays
5 6
T4GB-01-02-006
4 10
1 14 15 16 17 18
11 7
2 19 20 21 22 23
12 8
3
24 25 26 27 28
13 9
29 30 31 32 33
T4GC-01-02-002 T4GB-01-02-022
1- Flasher Relay 9- Front Window Heater 18 - Head Light Relay (Left) 26 - Load Dump Relay (B-R3)
Relay (A-R1)
2- Option Controller 10 - Neutral Relay 19 - Emergency Steering Relay 27 - Parking Brake Relay
(Optional) (A-R10) (B-R2)
3 - MCF 11 - Rear Window Heater Relay 20 - Horn Relay (A-R9) 28 - Parking Brake Relay
(B-R1)
4- ICF 12 - Wiper Relay (Left) 21 - Turn Signal Relay (Right) 29 - Fuel Pump Relay (B-R10)
(A-R8)
5- Dr.ZX Connector 13 - Wiper Relay (Right) 22 - Working Light Relay (Rear) 30 - Main Relay (B-R9)
(A-R7)
6- Fuse Box 14 - Reverse Light Relay 23 - Working Light Relay 31 - Rear Washer Relay (B-R8)
(A-R5) (Front) (A-R8)
7- Fog Light Relay (Optional) 15 - Brake Light Relay (A-R4) 24 - Front Wiper Relay (B-R5) 32 - Turn Signal Relay (Left)
(B-R7)
8- Auxiliary 16 - High Beam Relay (A-R3) 25 - Neutral Relay (B-R4) 33 - Rear Wiper Relay (B-R6)
17 - Head Light Relay (Right)
(A-R2)
T1-2-6
GENERAL / Component Layout
Right Console
PHOTO
Control Lever
011 012
PHOTO
Right Console
013
T4GB-01-02-006
2 3 4 5 6
7
1
8
9
10
18
17
16
15
14
13
12
T4GB-01-02-023
11
1 - Down Shift Switch 6 - Auxiliary Control Lever 11 - Emergency Steering Check 15 - Forward/Reverse Selector
(Optional) Switch Switch
2 - Bucket Control Lever 7 - Quick Coupler Switch (Optional) 12 - Fan Reversing Switch 16 - Lighter
3 - Lift Arm Control Lever 8 - Lift Arm Auto Leveler Downward 13 - Fog Light Switch (Optional) 17 - Up-shift/Down-shift Switch
Set Switch (Optional)
4 - Forward/Reverse Switch 9 - Lift Arm Auto Leveler Upward 14 - Ride Control Switch 18 - Hold Switch
Set Switch (Optional) (Optional)
5 - Horn Switch 10 - Front Control Lock Lever
T1-2-7
GENERAL / Component Layout
Monitor and Switches
PHOTO
Cab
004 005
1 2
T4GB-01-02-006
14 3
13
12
4
5
11 6
7
10
8 T4GB-01-02-024
1 - Monitor Panel 5 - Work Mode Selector Switch 9 - Front Wiper Switch 12 - Rear Wiper Switch
(Refer to T1-2-9)
2 - Driving Mode Switch 6 - Clutch Cut Position Switch 10 - Forward/Reverse Lever 13 - Working Light Switch
and Shift Switch
3 - Turn Signal Lever /Head Light 7 - Key Switch 11 - Air Conditioner Switch 14 - Hazard Light Switch
Switch/Dimmer Switch Panel
4 - Parking Brake Switch 8 - Steering Column Tilt
/Telescopic Lever
T1-2-8
GENERAL / Component Layout
Monitor Panel
1 2 3 4 5 6 7 8 9 10 11
34
33 12
13
14
32
15
31
T4GB-01-02-001
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
1 - Coolant Temperature 10 - Parking Brake Indicator 19 - Lever Steering Indicator 27 - Engine Warning Indicator
Gauge (Optional)
2 - Transmission Oil 11 - Clearance Light Indicator 20 - Monitor Mode Selector 28 - Overheat Indicator
Temperature Gauge
3 - Turn Signal Indicator 12 - Fuel Gauge 21 - Glow Signal 29 - Engine Low Oil Pressure
(Left) Indicator
4 - High Beam Indicator 13 - Brake Low Oil Pressure 22 - Monitor Display Selector (Up) 30 - Air Filter Restriction Indicator
Indicator
5 - Working Light Indicator 14 - Brake Low Oil Level 23 - Maintenance Indicator 31 - Transmission Warning
Indicator Indicator
6 - Turn Signal Indicator 15 - Emergency Steering 24 - Monitor Display selector 32 - Transmission Oil Filter
(Right) Indicator (Optional) (Down) Restriction Indicator
7 - Monitor Display 16 - Low Steering Oil Pressure 25 - Forward/Reverse Switch 33 - Hydraulic Oil Temperature
Indicator Indicator Indicator
8 - Stop Indicator 17 - Seat Belt Indicator 26 - Water Separator Indicator 34 - Transmission Oil
Temperature Indicator
9 - Service Indicator 18 - Discharge Warning
Indicator
T1-2-9
GENERAL / Component Layout
ENGINE AND FAN PUMP
1 2
PHOTO
Engine
030 042
3 6 7 8 9
5
10
11
4
14 13 12
T4GB-01-02-025
T1-2-10
GENERAL / Component Layout
PUMP DEVICE 1
2
PHOTO
Hydraulic System
114
T4GB-01-02-009
5 4
13
14
15
16
17
18
20 19 12 11 10
T4GC-01-02-001
1 - Main Pump 7- Torque Converter Input 12 - Transmission Middle Shaft 17 - 3rd Clutch Solenoid Valve
Speed Sensor Sensor
2 - Regulator 8 - Air Breather 13 - Forward Clutch Solenoid 18 - 4th Clutch Solenoid Valve
Valve
3 - Priority Valve 9- Charge Pump 14 - Reverse Clutch Solenoid 19 - Transmission Control Valve
Valve
4 - Pump Delivery Pressure 10 - Vehicle Speed 15 - 1st Clutch Solenoid Valve 20 - Parking Brake Pressure
Switch Sensor Switch
5 - Pilot Pump 11 - Transmission Output 16 - 2nd Clutch Solenoid Valve 21 - Regulator Valve
Speed Sensor
6 - Steering Relief Valve
T1-2-11
GENERAL / Component Layout
CONTROL VALVE
ZW220
5
T4GB-01-02-027
ZW250
5 1
PHOTO
Control Valve
089 090
3 2
T4GB-03-02-002C
1 - Over Load Relief Valve 3 - Over Load Relief Valve 4 - Make-up Valve 5 - Main Relief Valve
(Lift Arm: Bottom) (Bucket: Rod) (Lift Arm: Rod)
2 - Over Load Relief Valve
(Bucket: Bottom)
T1-2-12
GENERAL / Component Layout
RIDE CONTROL VALVE (OPTIONAL) CHARGING BLOCK
PHOTO
1 2 3 Charging Block
073
4 5
PHOTO
Ride Control
099
T4GB-01-02-013
T4GB-01-02-014 10 9 8 7
FAN MOTOR
10 11 12
PHOTO
Cooling Fan
039
T4GB-01-02-012
1 - Overload Relief Valve 5 - Service Brake Accumulator 8- Pilot Relief Valve 11 - Reverse Control Solenoid
(Front) Valve
2 - Ride Control Solenoid 6 - Service Brake Accumulator 9- Pump Torque Control 12 - Relief Valve
Valve (Rear) Solenoid Valve
3 - Ride Control Accumulator 7 - Relief Valve 10 - Parking Brake Solenoid 13 - Flow Control Solenoid
Valve Valve
4 - Pilot Accumulator
T1-2-13
GENERAL / Component Layout
STEERING VALVE
PHOTO
1 2 Steering System
078
T4GB-01-02-020
3 4 081
5 6
T4GB-01-02-010
T1-2-14
GENERAL / Component Specifications
ENGINE
ZW220
Manufacturer ............................................ ISUZU
Model........................................................ AH-6HK1XYWT-03 (Wet Type)
Type.......................................................... Diesel, 4 Cycle, Water Cooled, Over Head Valve, Inline,
Direct Injection, Turbo Charged
Cyl. NO. - Bore×Stroke............................. 6-115 mm×125 mm (4.53 in×4.92 in)
3 3
Piston Displacement................................. 7790 cm (475 in )
-1
Rated Output ............................................ 139.3±3 kW/2170 min (189±4 PS/2170 rpm)
-1
Max. Output .............................................. 164.3±3 kW/2000 min (223.4±4 PS/2000 rpm)
Compression Ratio................................... 17.5
Dry Weight................................................ 630 kg (1389 lb)
Firing Order .............................................. 1-5-3-6-2-4
Rotation Direction ..................................... Clock Wise (Viewed from fan side)
ZW250
Manufacturer ............................................ ISUZU
Model........................................................ AH-6HK1XYWT-04 (Wet Type)
Type.......................................................... Diesel, 4 Cycle, Water Cooled, Over Head Valve, Inline,
Direct Injection, Turbo Charged
Cyl. NO. - Bore×Stroke............................. 6-115 mm×125 mm (4.53in×4.92 in)
3 3
Piston Displacement................................. 7790 cm (475 in )
-1
Rated Output ............................................ 163.0±3 kW/2240 min (222±4 PS/2240 rpm)
-1
Max. Output .............................................. 179.1±3 kW/2000 min (243.5±4 PS/2000 rpm)
Compression Ratio................................... 17.5
Dry Weight................................................ 630 kg (1389 lb)
Firing Order .............................................. 1-5-3-6-2-4
Rotation Direction ..................................... Clock Wise (Viewed from fan side)
COOLING SYSTEM
Cooling Fan .............................................. Diameter 850 mm (33.47 in),
6 Blades (N6G-Type Blade, Steel Center), Draw-in Type
Thermostat ............................................... Cracking Temperature at Atmospheric Pressure:
82 °C (180 °F)
Full Open (Stroke: 10 mm (0.39 in) or more) Temperature:
95 °C (203 °F)
Fan Pump................................................. Gear Pump
T1-3-1
GENERAL / Component Specifications
LUBRICATION SYSTEM
Lubrication Pump Type............................. Gear Pump
Oil Filter .................................................... Full-Flow Paper Element Type with Bypass
Oil Cooler ................................................. Water Cooled Integral Type
STARTING SYSTEM
Motor ........................................................ Magnetic Pinion Shift Reduction Type
Voltage/Output.......................................... 24 V⋅5 kW
PREHEAT SYSTEM
Preheating Method ................................... Glow Plug (QOS II Type with After Glow)
ALTERNATOR
Type.......................................................... Regulator Integrated AC Type
Voltage/Output.......................................... 24 V⋅50 A (Brush less)
SUPERCHARGING SYSTEM
Model........................................................ RHG6
Type.......................................................... Exhaust Turbocharger Type
FUEL SYSTEM
Type.......................................................... Common Rail Type (HP4 Model)
Governor .................................................. Electrically Controlled
Injection Nozzle ........................................ Electric Multi Hole Injector (G2 Type)
T1-3-2
GENERAL / Component Specifications
PERFORMANCE
IMPORTANT: This list shows design specifications, which are not servicing standards.
ZW220
Fuel Consumption Ratio........................... 212.0±13.6 g/kW⋅h (156±10 g/PS⋅h) @ 2000 min-1 (rpm)
Maximum Output Torque .......................... 981±60 N⋅m (100±6 kgf⋅m) @ at approx. 1400 min-1 (rpm)
Compression Pressure............................. 3.04 Mpa (31 kgf/cm2) @ 200 min-1 (rpm)
Valve Clearance (Inlet/Exhaust)............... 0.4/0.4 mm (when cool)
No Load Speed......................................... Slow: (at Full Load: 850±20 min-1 (rpm))
Fast: (at Full Load: 2260±20 min-1 (rpm))
ZW250
Fuel Consumption Ratio........................... 212.0±13.6 g/kW⋅h (156±10 g/PS⋅h) @ 2000 min-1(rpm)
Maximum Output Torque .......................... 1022±60 N⋅m (104±6 kgf⋅m) @ at approx 1400 min-1 (rpm)
Compression Pressure............................. 3.04 MPa (31 kgf/cm2) @ 200 min-1 (rpm)
Valve Clearance (Inlet/Exhaust)............... 0.4/0.4 mm (0.016/0.016 in) (when cool)
No load Speed.......................................... Slow: (at Full Load: 850±20 min-1 (rpm))
Fast: (at Full Load: 2330±20 min-1 (rpm))
T1-3-3
GENERAL / Component Specifications
ZW220
Engine Performance Curve (AH-6HK1XYWT-03)
Test Condition:
1. In conformity with JIS D1005 (Performance Test Method for Diesel Engine Used for Construction Machinery)
under standard atmospheric pressure.
2. Equipped with the fan and alternator.
Torque
(N⋅m)
Output
(kW)
Fuel
Consumption
(g/kW⋅h)
-1
Engine Speed min (rpm) T4GC-01-03-001
T1-3-4
GENERAL / Component Specifications
ZW250
Engine Performance Curve (AH-6HK1XYWT-04)
Test Condition:
1. In conformity with JIS D1005 (Performance Test Method for Diesel Engine Used for Construction Machinery)
under standard atmospheric pressure.
2. Equipped with the fan and alternator.
Torque
(N⋅m)
Output
(kW)
Fuel
Consumption
(g/kW⋅h)
T1-3-5
GENERAL / Component Specifications
ENGINE ACCESSORIES
RADIATOR ASSEMBLY
Type.......................................................... Radiator and Oil Cooler Tandem Type Assembly
Intercooler and Torque Converter Cooler Tandem Type Assembly
Weight ...................................................... 67 kg (148 Ib) (ZW220)
74.5 kg (164 Ib) (ZW250)
ZW220
Radiator Oil Cooler
Capacity.................................................... 15 L (4 US gal) 5.1 L (3.3 US gal)
Air-Tight Test Pressure ............................. 100 kPa (1.0 kgf/cm2, 14.5 psi) 1500 kPa (15 kgf/cm2, 217 psi))
Cap Opening Pressure............................. 49 kPa (0.5 kgf/cm2, 7 psi) −
ZW250
Radiator Oil Cooler
Capacity.................................................... 18 L (4.8 US gal) 5.1 L (1.3 US gal)
Air-Tight Test Pressure ............................. 100 kPa (1.0 kgf/cm2,14.5 psi) 1500 kPa (15 kgf/cm2,217 psi))
Cap Opening Pressure............................. 49 kPa (0.5 kgf/cm2, 7 psi) −
BATTERY
Voltage...................................................... 12 V
Capacity.................................................... 108 Ah
T1-3-6
GENERAL / Component Specifications
HYDRAULIC FAN PUMP
Model........................................................ SGP1A27D2H1
Type.......................................................... Fixed Displacement Type Gear Pump
Maximum Flow (Theoretical Value).......... 60 L/min (15.85 US gpm)
SOLENOID VALVE
Function.................................................... Fan Motor Reverse Control
Fan Motor Speed Control
T1-3-7
GENERAL / Component Specifications
HYDRAULIC CONPONENT
MAIN PUMP
Type.......................................................... Bent Axis Type Variable Displacement Axial Plunger Pump
Maximum Flow (Theoretical Value).......... 270 L/min (71 US gum) (ZW220)
290 L/min (77 US gum) (ZW250)
REGULATOR
Type.......................................................... Hydraulic Pressure Operated Type
PRIORITY VALVE
Relief Set Pressure .................................. 27.4 MPa (280 kgf/cm2) @ 70 L/min (18.5 US gpm) (ZW220)
29.4 MPa (300 kgf/cm2) @ 90 L/min (23.8 US gpm) (ZW250)
PILOT PUMP
Model........................................................ HY/ZFS11/16.8
Type.......................................................... Fixed Displacement Type Gear Pump
Maximum Flow (Theoretical Value).......... 35 L/min (9.3 US gpm)
CONTROL VALVE
ZW220
Type.......................................................... Pilot Pressure Operated Type (2 Spools)
Main Relief Set Pressure.......................... 27.4 MPa (280 kgf/cm2) @ 200 L/min (52.8 US gpm)
Overload Relief Set Pressure................... 34.3 MPa (350 kgf/cm2) @ 35 L/min (9.3 US gpm)
(Lift Arm)
30.4 MPa (310 kgf/cm2) @ 35 L/min (9.3 US gpm)
(Bucket Tilt)
30.4 MPa (310 kgf/cm2) @ 50 L/min (13 US gpm)
(Bucket Dump)
ZW250
Type.......................................................... Pilot Pressure Operated Type (2 Spools)
Main Relief Set Pressure.......................... 29.4 MPa (300 kgf/cm2) @ 220 L/min (58 US gpm)
Overload Relief Set Pressure................... 36.8 MPa (375 kgf/cm2) @ 50 L/min (13 US gpm)
(Lift Arm)
32.5 MPa (330 kgf/cm2) @ 50 L/min (13 US gpm)
(Bucket Tilt, Bucket Dump)
T1-3-8
GENERAL / Component Specifications
RIDE CONTROL VALVE (OPTIONAL)
Type.......................................................... Pilot Pressure Operated Type
Overload Relief Set Pressure................... 39.2 MPa (400 kgf/cm2) @ 50 L/min (13 US gpm)
Charge Cut Pressure................................ 11.3 MPa (115 kgf/cm2)
CHARGING BLOCK
Charging Pressure ................................... Cut In Pressure: 11.8 MPa (120 kgf/cm2)
Cut Out Pressure: 14.7 MPa (150 kgf/cm2)
Pilot Relief Valve Set Pressure................. 3.7 MPa (38 kgf/cm2) @ 40 L/min (10.6 US gpm)
PILOT ACCUMULATOR
Capacity.................................................... 0.75 L (45.8 in3)
Charging Pressure ................................... 2.0 MPa (20 kgf/cm2)
STEERING VALVE
Type.......................................................... Flow Amp Type
Over Load Relief Set Pressure ................ 32.3 MPa (330 kgf/cm2) @50 L/min (13 US gpm) (ZW220)
34.3 MPa (350 kgf/cm2) @50 L/min (13 US gpm) (ZW250)
T1-3-9
GENERAL / Component Specifications
STEERING PILOT VALVE
Type.......................................................... Orbitrol Type
Gerotor Capacity ...................................... 96 cm3/rev (5.9 in3/rev)
STEERING ACCUMULATORv
Capacity.................................................... 0.2 L (12 in3)
Charging Pressure ................................... 8 MPa (82 kgf/cm2)
BRAKE VALVE
Brake Pressure......................................... 3.9 MPa (40 kgf/cm2)
T1-3-10
GENERAL / Component Specifications
• Travel System
TRANSMISSION
Type.......................................................... Counter Shaft Type
Gear Ratio ................................................ Forward 1st : 3.225
Forward 2nd : 1.901
Forward 3rd : 1.026
Forward 4th : 0.605
Reverse 1st : 3.225
Reverse 2nd : 1.901
Reverse 3rd : 1.026
Reverse 4th : 0.605
Parking Brake Release Pressure ............. 2.7 MPa (28 kgf/cm2)
ZW250
Model........................................................ Two Stage Transmission
Brake Type ............................................... Wet Multiplate Disk Brake
Brake Pressure......................................... 3.92 MPa (40 kgf/cm2)
Final Reduction Gear Ratio...................... 26.760
T1-3-11
GENERAL / Component Specifications
• Front Attachment
CYLINDER
ZW220 Lift Arm (Left/Right) Bucket Steering
Rod Diameter ........................................... 85 mm (3.35”) 95 mm (3.74”) 45 mm (1.77”)
Cylinder Bore............................................ 130 mm (5.12”) 165 mm (6.5”) 70 mm (2.76”)
Stroke ....................................................... 880 mm (34.65”) 510 mm (20.08”) 442 mm (17.40”)
Fully Retracted Length ............................. 1420 mm (55.91”) 1060 mm (41.73”) 804 mm (31.65”)
Plating Thickness ..................................... 30 µm (1.2 µin) 30 µm (1.2 µin) 30 µm (1.2 µin)
T1-3-12
GENERAL / Component Specifications
ELECTRICAL COMPONENT
ENGINE OIL PRESSURE SENSOR
Operation Pressure .................................. 29.4 kPa (0.3 kgf/cm2)
OVERHEAT SWITCH
Operation Temperature ............................ 105±2 ° C (221±2 °F)
BATTERY RELAY
Voltage/Current ........................................ 24 V⋅100 A
GLOW RELAY
Voltage...................................................... 24 V
SAFETY RELAY
Voltage...................................................... 24 V
HORN
Voltage/Current ........................................ 24 V⋅3.0±0.5 A
Sound Pressure........................................ 113±5 dB (A) @ 2 m (6’ 7”)
T1-3-13
GENERAL / Component Specifications
ILLUMINATION
Work Light ................................................ : Halogen 24 V, 55/70 W
Cab Light .................................................. : 24 V, 10 W
Head Light ................................................ : Halogen 24 V、75/70 W
Turn Signal Light ...................................... : Front : 24 V, 25 W
:Rear : 24 V, 21 W
Clearance Light ........................................ : 24 V, 5 W
License Light ............................................ : 24 V, 12 W
Reverse Light ........................................... : 24 V, 21 W
Tail Light ................................................... : 24 V, 5 W
Brake Light ............................................... : 24 V, 21 W
AIR CONDITIONER
Refrigerant................................................ 134a
Cooling Ability........................................... 4.65 kW (16.74 MJ, 3999 kcal) or more
Cool Air Volume........................................ 550 m3/h or more
Heating Ability........................................... 5.81 kW (20.92 MJ, 4997 kcal) or more
Warm Air Volume...................................... 400 m3/h or more
Temperature Adjusting System ................ Electronic Type
Refrigerant Quantity ................................. 1050±50 g
Compressor Oil Quantity .......................... 160 cm3
ELECTRICAL MOTOR
Voltage...................................................... 24 V, 2.4 kW
T1-3-14
SECTION 2
SYSTEM
—CONTENTS—
Group 1 Control System Group 4 Electrical System
Outline ...................................................... T2-1-1 Outline ...................................................... T2-4-1
Engine Control.......................................... T2-1-6 Main Circuit............................................... T2-4-2
Pump Control ......................................... T2-1-15 Electric Power Circuit................................ T2-4-3
Transmission Control.............................. T2-1-20 Indicator Light Check Circuit ..................... T2-4-4
Other Controls ........................................ T2-1-41 Accessory Circuit ...................................... T2-4-5
Control by Electric and Hydraulic Preheat Circuit .......................................... T2-4-6
Combined Circuit .................................. T2-1-51 Starting Circuit .......................................... T2-4-8
Charging Circuit ...................................... T2-4-12
Group 2 ECM System Serge Voltage Prevention Circuit ............ T2-4-16
Outline ...................................................... T2-2-1 Engine Stop Circuit ................................. T2-4-18
Fuel Injection Control ............................... T2-2-2 Lamplight Circait ..................................... T2-4-19
Compensation of Fuel Injection Head Light Circuit ................................... T2-4-20
Volume ................................................. T2-2-10 Turn Signal Circuit .................................. T2-4-24
Engine Start Control ................................T2-2-11 Brake Light Circuit .................................. T2-4-25
EGR Control ........................................... T2-2-12 Hazard Light Circuit ................................ T2-4-26
4GCT-2-1
(Blank)
4GCT-2-2
SYSTEM / Control System
GENERAL
There are four controllers as shown below with MC – MC, ECM, and monitor unit display indications on
Main Controller – installed at their center. monitors and make various controls of the vehicle
body by using analog signals received by each
· MC: Main Controller controller as well as digital signals detected on the
· ICF: Information Controller CAN.
· ECM: Engine Control Module
· Monitor Unit ICF stores machine history, receives digital signals for
various adjustments from Dr-ZX, transmits them to the
Controllers are mutually connected through CAN, and CAN, and transmits the vehicle body signal (digital
each controller uploads analog signals detected by signal) received by each controller to Dr-ZX.
sensors and switches as well as analog output signals A GPS-provision (optional) vehicle makes location
to solenoid valves on the CAN by converting them into arithmetic operation, utilising signals received by
digital ones. artificial sattelites, and transmits body information to
As the signals are processed into the digital ones, a the e-service host computer through artificial satellites.
large amount of signals detected at each controller can (Refer to the TROUBLESHOOTING/ICF)
be transmitted through few wires in a short time.
ICF
Receipt and
Transmission by
Digital Signal
ECM
MC
CAN
S
Sensors, Switches and
S Solenoid Valves
T2-1-1
SYSTEM / Control System
MC, ECM, and Monitor Unit are used for various
operation controls of the body.
T2-1-2
SYSTEM / Control System
Injectors
Sensors and
Switches for
Vehicle Body
MC ECM
Transmission
Solenoid Valves Engine
for Vehicle Body
Sensors and
Switches
Sensors and
Switches for Cab Solenoid Valves
and Monitor
Monitor
Unit
Relays for
Cab
Sensors and
Switches
Switches for
Traveling
Light-emitting
Dildes
Dr-ZX
ICF
GPS
T4GC-02-01-001
T2-1-3
SYSTEM / Control System
Sensors and switches to detect signals for various
operation controls and their controllers are as shown
below.
T2-1-4
SYSTEM / Control System
T2-1-5
SYSTEM / Control System
ENGINE CONTROL
T2-1-6
SYSTEM / Control System
Engine Control System Layout
PHOTO
Pedals
009
Work Mode
Selector Switch Accelerator Pedal
L Hydraulic Oil
Temperature
Sensor Accelerator Pedal Sensor
N
Main Pump
Delivery
Pressure Switch
Shift Switch
Transmission
MC ECM
Engine
T4GC-02-01-002
Engine Coolant
Temperature Sensor
T2-1-7
SYSTEM / Control System
Accelerator Pedal Control
T2-1-8
SYSTEM / Control System
Accelerator Pedal
Transmission
ECM
MC
Engine
Monitor
Unit
T4GC-02-01-003
T2-1-9
SYSTEM / Control System
Automatic Warming Up Control
T2-1-10
SYSTEM / Control System
PHOTO PHOTO
Overheat and
Hydraulic Oil Temp Coolant Temp
098 048
Hydraulic Oil
Temperature Sensor
Transmission
MC ECM
Engine
Monitor
Unit
Engine
Coolant
Temperature
Sensor
T4GC-02-01-004
T2-1-11
SYSTEM / Control System
Engine Torque Control
T2-1-12
SYSTEM / Control System
Work Mode
Selector Switch
L&C
N PHOTO
Torque Converter
P
109
Main Pump
Delivery
Pressure Switch
Shift Switch
Transmission
MC ECM
Engine
Torque Converter
Output Speed Sensor
Torque Converter
Monitor Input Speed Sensor
Unit
T4GC-02-01-005
T2-1-13
SYSTEM / Control System
(Blank)
T2-1-14
SYSTEM / Control System
PUMP CONTROL
MC ECM Transmission
Engine
Main Pump
regulator Pump Torque Control
Solenoid Valve
Torque Converter
Monitor Output Speed Sensor
Unit
Torque Converter
Input Speed Sensor
T4GC-02-01-006
T2-1-15
SYSTEM / Control System
Standard Torque Control
Operation:
1. When accelerator pedal is stepped, MC makes
arithmetic operation of the target engine speed.
Q
2. MC makes arithmetic operation of the pump
maximum tilting angle by receiving the target Flow
engine speed signal, and transmits signal to the
pump torque control solenoid valve. P-Q Line
Pressure P
T2-1-16
SYSTEM / Control System
Accelerator Pedal
MC ECM Transmission
Engine
Main Pump
Regulator Pump Torque Control
Solenoid Valve
Monitor
Unit
T4GC-02-01-007
T2-1-17
SYSTEM / Control System
Torque Reduction Control
Operation:
Q
1. When accelerator pedal is stepped, MC makes
arithmetic operation of the target engine speed. Flow
T2-1-18
SYSTEM / Control System
Accelerator Pedal
MC ECM Transmission
Engine
Main Pump
Regulator Pump Torque Control
Solenoid Valve
Torque Converter
Output Speed Sensor
Monitor
Torque Converter
Unit
Input Speed Sensor
T4GC-02-01-008
T2-1-19
SYSTEM / Control System
TRANSMISSION CONTROL
T2-1-20
SYSTEM / Control System
Transmission Control System Layout
Key Switch
Reverse Clutch
Clutch Cut Transmission Forward Solenoid Valve
Position Switch Middle Shaft Clutch Solenoid
Sensor Valve
OFF
S
Transmission
N
D
MC ECM
Vehicle Speed
Sensor
Torque Torque
Forward/Reverse Converter Converter
Lever Input Output
Speed Speed
F Sensor Sensor
Forward/Reverse
Switch
N OFF DOWN ON
R ON UP HOLD OFF
T2-1-21
SYSTEM / Control System
Neutral Control
Purpose: Protection of transmission during working of IMPORTANT: Be careful that in case the parking
parking brake by restricting clutch connec- brake pressure sensor is abnormal,
tion despite operation of forward/reverse traveling is possible even if the
lever or forward/reverse switch parking brake switch is ON and the
parking brake is at work because the
Operation: parking brake alarm lamp is turned
OFF and fixed (release).
1. In case either of the signal from forward/reverse
lever, forward signal or reverse signal of the for-
ward/reverse switch is transmitted to the MC, the
MC confirms the detected value of the parking
brake pressure sensor.
2. When the parking brake pressure is higher than
the set pressure, the MC transmits signal to the
clutch solenoid valve, but does not when lower
than that.
T2-1-22
SYSTEM / Control System
MC ECM
Engine
Transmission
Parking Brake
Pressure Sensor
Monitor
Unit
Parking Brake
Solenoid Valve
Parking Brake
Forward/Reverse
Lever
Forward/Reverse
Switch
N OFF ON
R ON OFF
T2-1-23
SYSTEM / Control System
Forward/Reverse Lever Priority Control
Operation:
1. In case the forward/reverse lever is operated
while traveling using the forward/reverse switch,
the MC disables operation of the forward/reverse
switch, and makes forward/reverse control by in-
put signal from the forward/reverse lever.
2. For restarting operation using the forward/reverse
switch has the forward/reverse switch effective
again by turning the forward/reverse selector
switch ON while making both the forward/reverse
lever and the forward/reverse switch at the neutral
position.
3. From then on until the forward/reverse lever is
operated next, the MC makes forward/reverse
control by the forward/reverse switch input signal.
T2-1-24
SYSTEM / Control System
PHOTO
Right Console
Forward Clutch Reverse Clutch
013 Solenoid Valve Solenoid Valve
MC ECM
Engine
Transmission
Monitor
Unit
Forward/Reverse
Lever
Forward/Reverse
Switch
N OFF
R ON
Forward/Reverse T4GC-02-01-011
Selector Switch
T2-1-25
SYSTEM / Control System
Forward/Reverse Selector Control While Travel-
ing
Operation:
1. In case the forward/reverse lever is changed to
reverse while traveling forward at speed higher
than the speed allowed for operation of the for-
ward/reverse lever, the MC lowers the speed shift
by transmitting speed shift signal of Speed
4®3®2 to the transmission if the speed shift is
Speed 4.
2. If the vehicle speed is lowered to the set speed by
operation of the brake pedal or otherwise, the MC
transmits signal to the reverse clutch solenoid
valve to have the clutch shifted reverse.
3. As the speed increases when the accelerator
pedal is stepped, the MC transmits speed shift
signal of Speed 2 to Speed 3 to each speed shift
solenoid valve, and increases the speed shift.
T2-1-26
SYSTEM / Control System
Shift Switch
MC ECM
Engine 1 2 3 4
Speed Shift Solenoid Valve
Vehicle Speed
Sensor
Monitor Transmission
Unit
Forward/Reverse
Lever
Forward/Reverse
Switch
N OFF
R ON
Forward/Reverse T4GC-02-01-012
Selector Switch
T2-1-27
SYSTEM / Control System
Manual Speed Shift Control
T2-1-28
SYSTEM / Control System
Driving Mode
Switch Accelerator Pedal Brake Pressure
Sensor Sensor PHOTO
M
Accelerator Brake Pedal Cab
L Pedal
005
N
Shift Switch
Forward Clutch
Solenoid Valve
MC ECM
Engine 1 2 3 4
Speed Shift Solenoid Valve
Vehicle Speed
Sensor
Monitor Transmission
Unit
Forward/Reverse
Lever
Forward /Reverse
Switch
N OFF
R ON
Forward/Reverse T4GC-02-01-013
Selector Switch
T2-1-29
SYSTEM / Control System
Automatic Speed Shift Control 4. MC transmits signal to the selected speed shift
solenoid valve in response to the output value
Purpose: Automatic speed shift with three kinds of each time of the torque converter input speed
timing selection sensor, torque converter output speed sensor,
vehicle speed sensor and accelerator pedal sen-
Operation: sor. MC eventually makes speed shift control until
1. If either of L, N, and H of the Driving Mode switch the selected speed shift.
is selected, the MC is supplied with votage cor-
responding to the selected mode. NOTE: MC is so programmed as to dtermine nec-
essary vehicle speed ranges for changing
Automatic Automatic to the respective speed shifts and accel-
Mode Automatic L
N H erator pedal output value. Therefore, in
Output case Automatic L of the Driving mode
2V 3V 4V switch and Speed 3 of the speed shift
Voltage
switch are selected at start of traveling,
traveling is started at Speed 2 first, and
2. MC started the selected automatic speed shift
shifted up to Speed 3 as the vehicle speed
program.
increases. Conversely, in case speed shift
· In Automatic L control, the timing of speed shifting up from Speed 3 to Speed 1 is attempted while
is slow when started at Speed 2, which is advanta-
traveling by operating the speed shift switch,
geous in making much of low fuel consumption.
Speed 2 is automatically selected first, and
· In Automatic N control, the timing of speed shifting Speed 1 is reached after the vehicle speed
up is fast when started at Speed 2, which is advan-
is lowered to the speed range for Speed 1.
tageous in making much of production as well as low
fuel consumption.
· In Automatic H control, though started at Speed 2, NOTE: In case the Driving mode switch becomes
besides slow speed shifting up, speed shift to Speed out of order, the MC makes speed shift
1 is necessary if traveling load is high, which is ad- control in the manual traveling mode.
vantageous in making much of production.
NOTE: In case the solenoid valve of either of the
NOTE: In whichever of Modes L, N, and H, starting Speed 1, Speed 3, or Speed 4 becomes
is made at Speed 1, if the speed shift switch abnormal, the travel speed will be fixed to
of Speed 1 is selected. Speed 2. In case either of the forward
clutch solenoid valve, reverse clutch sole-
3. Shift switch is the rorary type, and has two noid valve, or Speed 2 solenoid valve be-
switches inside. When the speed shift is selected comes abnormal, only the abnormal one
from among Speed 1 through Speed 4, signal of cannot be used.
the selected speed shift is transmitted to the MC
depending on the combination of ON inside the NOTE: In case the travel speed sensor has be-
speed shift switch. come abnormal, the travel speed is calcu-
lated using the transmission intermediate
Speed Speed Speed Speed shaft sensor, but with a large error. In case
Speed Shift both of the travel speed sensor and the
1 2 3 4
transmission intermediate shaft sensor
Internal Switch have become abnormal, travel at Speed 2
ON ON
1 is fixed.
Internal Switch
ON ON
2 NOTE: Speed shift selected by the speed shift
switch is the highest speed shift.
T2-1-30
SYSTEM / Control System
Driving Mode
Switch Accelerator Pedal Brake Pressure
Sensor Sensor
M
Accelerator Pedal Brake Pedal
L
Shift Switch
Forward Clutch
Solenoid Valve
Transmission
MC ECM
1 2 3 4
Engine
Speed Shift Solenoid Valve
Vehicle Speed
Sensor
Monitor
Unit
Forward/Reverse
Lever Torque Converter Torque Converter
Input Speed Sensor Output Speed Sensor
F
Forward/Reverse
Switch
N OFF
R ON
Forward/Reverse T4GC-02-01-014
Selector Switch
T2-1-31
SYSTEM / Control System
Down Shift Control
Purpose: Decreasing the speed shift by pushing the 8. In case of the following, the down shift switch
switch installed at the right console. control is canceled.
• Operation of the forward/reverse lever or the for-
Operation: ward/reverse switch
• Operation of the shift switch
1. When traveling at Speed 4 in Automatic L mode of
• Operation of the Driving mode switch
the Driving mode switch, signal is transmitted to
• Pushing the hold switch
the MC by pushing the down shift switch once.
(Only in Automatic mode of the Driving mode
2. When traveling faster than the allowable speed switch)
shift, the MC cancels the signal from the down
shift switch, but transmits signal to the speed shift NOTE: In case the vehicle speed sensor becomes
solenoid valve of Speed 3, when traveling slow. abnormal, the MC receives signal from the
3. Further, if the down shift switch is pushed and the transmission middle shaft sensor, and con-
vehicle speed is lowered to the range allowing the trols by making arithmetic operation of the
speed shift, the speed shift of Speed 2 is selected. vehicle speed allowable for the speed shift.
In case both the vehicle speed sensor and
4. In case automatic mode of the Driving mode the transmission middle shaft sensor are
switch is selected, automatic speed shift control is abnormal, lowering the speed shift is pos-
recovered three seconds after the speed shift has sible as an emergency measure only when
lowered, and then the speed shift is automatically the engine stops for one reason or another
raised once the vehicle speed increases. but traveling is not stopped.
5. By keeping pushing the down shift switch, the
speed shift is lowered to Speed 2, and Speed 2 is NOTE: Shift switch has two switches, and their
kept during pushing. combination of ON varies depending on
each speed shift. Controller judges which
6. If the down switch is pushed again within three
speed shift has been selected by the com-
seconds after removing the finger once, Speed 1
bination of the two input signals.
is obtained in case the vehicle speed is slow
enough to allow the speed shift down.
NOTE: Forward/reverse switch does not transmit
7. When the down shift switch is pushed in manual
neutral signal. In case of no electric current
mode of the Driving mode switch, in case the ve-
from the forward/reverse switch, the con-
hicle speed is slow enough to allow the down shift,
troller judges the switch as neutral (N).
the speed shift is lowered and the shifted speed is
kept.
T2-1-32
SYSTEM / Control System
Driving Mode
Switch
Accelerator Pedal Sensor Brake Pressure Sensor
M
Accelerator Pedal Brake Pedal
L
Shift Switch
Reverse Clutch
Solenoid Valve
MC ECM
Engine 1 2 3 4
Speed Shift Solenoid Valve
Vehicle
Transmission Speed Sensor
Monitor
Unit
Forward/Reverse
Lever
Forward/Reverse
Switch
N OFF DOWN
R ON UP HOLD
T2-1-33
SYSTEM / Control System
Up Shift Control
Purpose: Raising the speed shift by putting the left NOTE: Shift switch has two switches, and their
hand on the steering wheel and pressing the combination of ON varies depending on
switch installed at the right console each speed shift. Controller judges which
speed shift has been selected by the com-
Operation: bination of the two input signals.
1. Signal is transmitted to the MC by pushing the up
shift switch once when traveling at Automatic L NOTE: Forward/reverse switch does not transmit
mode of the Driving mode switch and Speed 4 of neutral signal. In case of no electric current
the shift switch. from the forward/reverse switch, the con-
troller judges the switch as neutral (N).
2. MC transmits signal to the speed shift solenoid
valve of Speed 2, and the speed shift is raised.
NOTE: Each mode switch of the Driving mode
3. If the up shift switch is pushed, the speed shift is switch is supplied with respectively different
further raised to Speed 3 and Speed 4. voltages from the monitor unit, and when
4. In case automatic travel mode switch is selected, the switch selects a mode, the MC judges
the speed shift is raised, and returned to the which mode has been selected by the input
automatic speed shift control in three seconds, voltage.
eventually rising automatically to the speed shift
selected in advance.
5. In case manual travel mode switch is selected, the
raised speed shift is kept.
6. In case the following operations are made, the up
shift switch is released.
• Operation of the forward/reverse lever or for-
ward/reverse switch
• Operation of the shift switch
• Operation of the Driving mode switch
• Pushing the hold switch
(only when the automatic of the Driving mode
switch is selected)
T2-1-34
SYSTEM / Control System
Shift Switch
Forward Clutch
Solenoid Valve
Reverse Clutch
Solenoid Valve
MC ECM
Engine 1 2 3 4
Speed Shift Solenoid Valve
Monitor Transmission
Unit
Forward/Reverse
Lever
Forward/Reverse
Switch
N OFF DOWN
R ON UP HOLD
T2-1-35
SYSTEM / Control System
Clutch Cut Control
Purpose: Enabling release of the forward/reverse 5. In case the brake pressure is lowered below the
clutch of the transmission for making the set pressure by reducing the amount of stepping
most of the engine torque by operating the of the brake pedal, signal transmitted to the clutch
brake during operation of the front attach- solenoid valve is raised, and clutching is made
ment. again.
Amount of stepping the brake pedal at the
time of declutching can be selected from NOTE: In case either of the clutch cut position
among three kinds depending on the driver’s switch and brake pressure sensor becomes
preference. out of order, clutch cut control is not made
Operation:
NOTE: Each mode switch of the clutch cut position
1. When either mode of the clutch cut position switch switch is provided with respectively different
is selected, voltage corresponding to the selected voltages from the monitor unit, and when
mode is transmitted to the MC. the switch selects a mode, the MC judges
which mode has been selected by the input
Mode OFF S N D voltage.
Input
1V 2V 3V 4V
Voltage
T2-1-36
SYSTEM / Control System
PHOTO
Cab
005
Brake Pressure
Sensor Brake Pedal
Clutch Cut
Position Switch
OFF
Forward Clutch
S Solenoid Valve
N
Reverse Clutch
Solenoid Valve
D
MC ECM
Engine
Transmission
Monitor
Unit
T4GC-02-01-017
T2-1-37
SYSTEM / Control System
Shift Holding Control
Purpose: Enabling to hold the speed shift during tow- NOTE: Shift switch has two switches, and their
ing or traveling uphill combination of ON varies depending on
each speed shift. Controller judges which
Operation: speed shift has been selected by the com-
1. When the hold switch is pressed once, signal is bination of the two input signals.
transmitted to the MC.
NOTE: Forward/reverse switch does not transmit
2. MC keeps transmitting signal to the speed shift
neutral signal. In case of no electric current
solenoid valve of each time, and after that the
from the forward/reverse switch, the con-
speed shift is fixed even if the the accelerator or
troller judges the switch as neutral (N).
the brake pedal is stepped.
T2-1-38
SYSTEM / Control System
Key Switch
PHOTO
Driving Mode Switch
Accelerator Pedal Brake Pressure Control Lever
Sensor Sensor
M
Accelerator Pedal Brake Pedal
011 012
L
Shift Switch
Forward Clutch
Solenoid Valve
MC ECM
Engine 1 2 3 4
Transmission
Monitor
Unit
Forward/Reverse
Lever
Forward/Reverse
Switch
N OFF DOWN ON
R ON UP HOLD OFF
T4GC-02-01-018
T2-1-39
SYSTEM / Control System
(Blank)
T2-1-40
SYSTEM / Control System
OTHER CONTROLS
T2-1-41
SYSTEM / Control System
Hydraulic Fan Cooling Control
Operation:
1. When the engine is started, the fan pump rotates
and discharges oil to the fan motor.
2. Signals from the hydraulic oil temperature sensor,
engine coolant temperature sensor and torque
converter oil temperature sensor are simultane-
ously transmitted to the MC, and arithmetic op-
eration of three target hydraulic fan speeds are
carried out.
3. MC selects the highest temperature and transmits
signal to the flow control solenoid valve.
4. Flow control solenoid valve operates and pressure
oil coming from it flows into the right end of the
flow control valve, so the flow control valve spool
moves left.
5. When the flow control valve spool moves left, part
of the pressure oil flowing to the fan motor flows to
the tank port, and the fan motor speed is lowered
accordingly.
6. In case oil temperature or coolant temperature of
any part is above the set temperature, the hy-
draulic fan speed is maximized when the engine
speed is in maximum.
7. In case oil temperature or coolant temperature of
any part is below the set temperature, the hydrau-
lic fan speed is lowered in response to the datum
of the highest temperature.
8. Besides, the signal from the outside air tempera-
ture sensor also enters the MC, and rotates the
fan always at the maximum speed, disregarding
the controls in 2 through 7 in case the air condi-
tioner switch is ON at the outside air temperature
of 35 °C (95 °F) and above.
T2-1-42
SYSTEM / Control System
At oil temperature or coolant temperature above the set temperature (Uncontrolled speed operation)
PHOTO
Fan Motor
Cooling Fan
039
Flow Control Valve
Flow Control
Hydraulic Oil Temperature Sensor
Solenoid Valve
Fan Pump
Air
Conditioner Monitor Torque Converter
Control Unit Oil Temperature Sensor
Panel
T4GC-02-01-019
At oil temperature or coolant temperature below the set temperature (Controlled speed operation)
Fan Motor
Engine Coolant
Temperature Sensor
Out Side
Temperature
Sensor
MC ECM
Trans-
Engine mission
T4GC-02-01-020
T2-1-43
SYSTEM / Control System
Hydraulic Fan Cleaning Control
Purpose: Control of cleaning by hydraulic fan by re- NOTE: Reverse control solenoid valve is turned
versing the hydraulic fan to blow away dust ON temporarily when the key switch is
in case cleaning of the radiator and oil cooler turned ON because the spool can stick in
are needed case the reverse control solenoid valve is
not operated for a long time. It is also
Operation: turned ON once every one minute after the
key switch is turned ON. This operation is
1. When the engine is started after preparing the not made during the hydraulic fan cleaning
following conditions and turning the fan reversing operation.
switch ON, signal is transmitted from the MC to
the reverse control solenoid valve.
2. When the reverse control solenoid valve is oper-
ated, the reverse spool strokes and the fan motor
rotation is reversed.
3. In reverse rotation, as hydraulic fan cooling con-
trol is not made, the fan speed fluctuates from
maximum to minimum in response to the amount
of stepping the accelerator pedal.
4. In case any one of the conditions below is
changed during reverse rotation, the engine
speed is immediately fixed to idling.
5. Hydraulic fan cleaning control is not released by
turning the fan reversing switch OFF only. Control
is released by the procedure of turning the fan
reversing switch OFF – turning the key switch
OFF – turning the key switch ON.
6. In case the engine speed is fixed to idling also, the
control is released by the procedure of turning the
fan reversing switch OFF – turning the key switch
OFF – turning the key switch ON.
Conditions:
• Fan reversing switch: ON
• Parking brake switch: ON (Brake is effective.)
• Forward/reverse lever: neutral
• Forward/reverse switch: neutral
T2-1-44
SYSTEM / Control System
Fan Motor
Reverse Spool
Reverse Control
Solenoid Valve
Trans-
Engine mission
Hydraulic Oil
Tank
T4GB-02-01-007
Fan Motor
Reverse Spool
Reverse Control Solenoid Valve
Hydraulic Oil
Tank
Trans-
Engine mission
Parking Brake
Solenoid Valve
ON
F F
N N ON
R R OFF
T2-1-45
SYSTEM / Control System
Transmission Alarm Control
Purpose: Lighting the transmission alarm lamp on the • Torque converter input speed sensor
monitor unit for protection of the transmis- • Torque converter output speed sensor
sion in case of disorder of parts likely to • Vehicle speed sensor
cause damage to the transmission • Transmission middle shaft sensor
• Forward/reverse lever
Operation: In case any of the parts shown right be- • Forward/reverse switch during work
comes out of order, the MC transmits signal
to the monitor unit, and the transmission
alarm lamp is lit.
Torque Converter
Output Speed
Sensor
Monitor
Unit
F F
N N
R R
T2-1-46
SYSTEM / Control System
Forward/Reverse Indicator Control
Purpose: Lighting the forward/reverse indicator on the NOTE: In case the forward/reverse lever is oper-
monitor when the forward/reverse switch is ated while traveling using the for-
effective ward/reverse switch, input to the for-
ward/reverse switch becomes ineffective,
Operation: and the vehicle body moves by operating
1. Forward/reverse selector switch is turned ON after the forward/reverse lever. (Refer to the
the forward/reverse lever and the forward/reverse Forward/Reverse Lever Priority Control)
switch are positioned at neutral.
2. Then the forward/reverse switch becomes effec- NOTE: Forward/reverse switch does not transmit
tive, and the monitor unit lights the for- neutral signal. In case of no electric current
ward/reverse indicator of the monitor. from the forward/reverse switch, the con-
troller judges the switch as neutral (N).
NOTE: In case the forward/reverse lever becomes
out of order, input to the forward/reverse
switch becomes ineffective, and the for-
ward/reverse indicator is unlit and fixed.
Monitor
MC ECM
Forward/Reverse Indicator
Monitor
Unit
F F
N N OFF
R R ON
T2-1-47
SYSTEM / Control System
Reverse Traveling Alarm Control
(Refer to the SYSTEM/Electric System)
Operation:
1. When reverse of the forward/reverse lever or the
forward/reverse switch is selected, the MC earths
the terminal from the reverse light relay.
2. Reverse light relay is excited, and electric current
flows to the reverse light and the reverse buzzer.
Right
Reverse Light
Reverse Buzzer
MC ECM
N Monitor
Unit
Forward/Reverse
From Terminal #108
Lever T4GC-02-01-024
or of Fuse Box A
Forward/Reverse
Switch
T2-1-48
SYSTEM / Control System
Parking Brake Alarm Control
Purpose: Lighting the parking brake alarm lamp on the NOTE: Parking brake of the vehicle body is re-
monitor unit during parking operation of the leased if the pilot pressure flows in.
brake
NOTE: For operation circuit of the parking brake,
Operation:
refer to the SYSTEM/Electric System.
1. When the parking brake switch is turned ON, the
MC confirms signal of the parking brake pressure IMPORTANT: Be careful that in case the parking
sensor. brake pressure sensor is abnormal,
traveling is possible even if the
2. At pressure below the set pressure, the MC
parking brake switch is ON and the
transmits signal to the monitor unit, and the park-
parking brake is at work because the
ing brake alarm lamp is lit.
parking brake alarm lamp is fixed to
OFF (release).
Monitor
MC ECM
Engine Trans-
mission
Parking Brake
Pressure Sensor
Parking Brake
ON Parking Brake
Solenoid Valve
OFF
T2-1-49
SYSTEM / Control System
(Blank)
T2-1-50
SYSTEM / Control System
CONTROLS BY ELECTRICAL AND HY-
DRAULIC COMBINED CIRCUIT
T2-1-51
SYSTEM / Control System
Ride Control (Optional)
Operation:
1. When the ride control switch is turned ON, the MC
makes the ride control effective and the ride con-
trol indicator of the monitor is lit.
2. At vehicle speed of 7 km/h (4 mph) and above, the
MC receives signal from the vehicle speed sensor,
and transmits electric current to the ride control
solenoid valve.
3. When the ride control solenoid valve is operated
and the spool moves, a damper circuit is organ-
ized between the rod ends and the bottom ends of
the lift arm cylinder. When the vehicle travels on
bumpy roads, the fluctuation of the bottom pres-
sure of the lift arm cylinders is absorbed by the
ride control accumulator, and the shock of the
whole vehicle body is reduced.
T2-1-52
SYSTEM / Control System
PHOTO PHOTO
MC ECM
Engine Trans-
mission
To Control
Valve
Monitor
Vehicle Speed Sensor
Unit
Ride Control
OFF Accumulator
Ride Control
ON Indicator
Ride Control Valve
Relief Valve
Ride Control
Switch
Ride Control
Solenoid Valve
Spool
Pilot
Pump
Hydraulic Oil
Tank
T4GC-02-01-026
T2-1-53
SYSTEM / Control System
Bucket Auto-leveler Control (ZW220)
Operation:
1. In dumping operation of the bucket, the bar is lo-
cated in front of the bucket proximity switch.
While the bar passes by the bucket proximity
switch, the bucket proximity switch becomes ON,
and excites the electromagnet on the bucket tilting
end of the pilot valve.
2. When the bucket operation lever is moved farther
than the bucket tilting detent position (position to
move farther than the tilting position), the bucket
operation lever is retained by the electromagnet
on the bucket tilting end, and pressure oil from the
pilot valve moves the bucket spool of the control
valve.
3. Pressure oil from the main pump flows into the
bottom end of the bucket cylinder through the
bucket spool of the control valve, and extends the
bucket cylinder. When the bucket cylinder is ex-
tended, the bar also passes by the bucket prox-
imity switch.
4. When the bar becomes distant from the bucket
proximity switch, the bucket proximity switch is
turned OFF, and the electromagnet on the bucket
tilting end is also turned OFF, which makes the
bucket operation lever in the neutral position. As
the bucket spool of the control valve also returns
to neutral, the bucket cylinder stops. As a result,
the bucket is tilted at the right digging angle
(horizontal).
T2-1-54
SYSTEM / Control System
PHOTO
Proximity Switch
Bucket Cylinder Bucket Proximity Switch Bar 092 093
Pilot Valve
for Bucket
Bucket
Electromagnet
on Bucket Tilting End
Pilot
Pump
Lift Arm
Hydraulic Oil
Main Tank T4GB-02-01-013
Pump
T2-1-55
SYSTEM / Control System
Bucket Auto-leveler Control (ZW250)
Operation:
1. In dumping operation of the bucket, the bar is lo-
cated in front of the bucket proximity switch.
While the bar passes by the bucket proximity
switch, the bucket proximity switch becomes ON,
and excites the electromagnet on the bucket tilt-
ing end of the pilot valve.
2. When the bucket operation lever is moved farther
than the bucket tilting detent position (position to
move farther than the tilting position), the bucket
operation lever is held by the electromagnet on
the bucket tilting end, and pressure oil from the
pilot valve moves the bucket spool of the control
valve.
3. Pressure oil from the main pump flows into the
bottom end of the bucket cylinder through the
bucket spool of the control valve, and extends the
buket cylinder. When the bucket cylinder is ex-
tended, the bar also passes by the bucket prox-
imity switch.
4. When the bar becomes distant from the bucket
proximity switch, the bucket proximity switch is
turned OFF, and the electromagnet on the bucket
tilt end is also turned OFF, which makes the
bucket operation lever in the neutral position. As
the bucket spool of the control valve also returns
to neutral, the bucket cylinder stops. As a result,
the bucket is tilted at the right digging angle
(horizontal).
T2-1-56
SYSTEM / Control System
Pilot Valve
for Bucket
Electromagnet
on Bucket Tilting End Bucket
Pilot
Pump
Lift Arm
Hydraulic Oil
Main Tank T4GB-02-01-033
Pump
T2-1-57
SYSTEM / Control System
Lift Arm Float Control (ZW220)
Operation:
1. When the lift arm operation lever is moved to the
floating position (farther position than the lift arm
lowering position), the lift arm operation lever is
retained by the electromagnet on the lift arm low-
ering end, and pressure oil from the pilot valve
moves the lift arm spool of the control valve up to
the floating position (farthest right position).
T2-1-58
SYSTEM / Control System
Bottom End
Port
Rod End
Port
Control Valve
Electromagnet
on Lift Arm Lowering End
Bucket
Pilot Valve
for Lift Arm
Lift Arm
Pilot
Pump
Hydraulic Oil
Main Tank T4GB-02-01-014
Pump
T2-1-59
SYSTEM / Control System
Lift Arm Float Control (ZW250)
Operation:
1. When the lift arm operation lever is moved to the
floating position (farther position than the lift arm
lowering position), the lift arm operation lever is
retained by the electromagnet on the lift arm low-
ering end, and pressure oil from the pilot valve
moves the lift arm spool of the control valve up to
the floating position (farthest left position).
T2-1-60
SYSTEM / Control System
Bottom End
Port
Rod End
Port
Control Valve
Electromagnet
on Lift Arm Lowering End
Bucket
Pilot Valve
for Lift Arm
Lift Arm
Pilot
Pump
Hydraulic Oil
Main Tank T4GB-02-01-034
Pump
T2-1-61
SYSTEM / Control System
Lift Arm Kick-out Control (ZW220)
Operation:
1. When lowering the lift arm, the plate is located in
front of the lift arm proximity switch.
While the plate passes by the lift arm proximity
switch, the lift arm proximity switch becomes ON,
and the electromagnet on the lift arm end is also
excited.
2. When the lift arm operation lever is moved farther
than the lift arm raising detent position (position to
pull farther than the raising position), the bucket
operation lever is retained by the electromagnet
on the lift arm raising end, and pressure oil from
the pilot valve moves the lift arm spool of the
control valve toward raising.
3. Pressure oil from the main pump flows into the
bottom ends of the lift arm cylinders through the
lift arm spool of the control valve, and extends the
lift arm cylinders. When the lift arm cylinders are
extended, the plate also passes by the lift arm
proximity switch.
4. When the plate becomes distant from the lift arm
proximity switch, the lift arm proximity switch is
turned OFF, and the electromagnet on the lift arm
raising end is also turned OFF, which makes the
lift arm operation lever in the neutral position. As
the lift arm spool of the control valve also returns
to neutral, the lift arm cylinders stop. As a result,
the lift arm stops.
T2-1-62
SYSTEM / Control System
Lift Arm
Plate Proximity Switch
Lift Arm
Cylinder
Control Valve
Pilot Valve
for Lift Arm
Lift Arm
Electromagnet
on Lift Arm Lowering End
Pilot
Pump
Hydraulic Oil
Main
Tank T4GB-02-01-015
Pump
T2-1-63
SYSTEM / Control System
Lift Arm Kick-out Control (ZW250)
Operation:
1. When lowering the lift arm, the plate is located in
front of the lift arm proximity switch.
While the plate passes by the lift arm proximity
switch, the lift arm proximity switch becomes ON,
and the electromagnet on the lift arm end is also
excited.
2. When the lift arm operation lever is moved farther
than the lift arm raising detent position (position to
pull farther than the raising position), the bucket
operation lever is retained by the electromagnet
on the lift arm raising end, and pressure oil from
the pilot valve moves the lift arm spool of the
control valve toward raising.
3. Pressure oil from the main pump flows into the
bottom ends of the lift cylinders through the lift
arm spool of the control valve, and extends the lift
arm cylinders. When the lift arm cylinder is ex-
tended, the plate also passes by the lift arm
proximity switch.
4. When the plate becomes distant from the lift arm
proximity switch, the lift arm proximity switch is
turned OFF, and the electromagnet on the lift arm
raising end is also turned OFF, which makes the
lift arm operation lever in the neutral position. As
the lift arm spool of the control valve also returns
to neutral, the lift arm cylinders stop. As a result,
the lift arm stops.
T2-1-64
SYSTEM / Control System
Lift Arm
Plate Proximity Switch
Lift Arm
Cylinder
Control Valve
Lift Arm
Pilot
Pump
T2-1-65
SYSTEM / Control System
Lift Arm Auto-leveler Upward Control (Optional)
(ZW220)
Operation:
1. If the SET position of the lift arm auto-leveler 3. Pressure oil from the main pump flows into the
upward set switch is selected after the lift arm is bottom end ports of the lift cylinder through the lift
located within the allowable location of the lift arm arm spool of the control valve, and raises the lift
auto-leveler (a’ in the illustration), signal from the arm.
lift arm angle sensor is memorized by the MC,
4. When the lift arm angle sensor moves up to the lift
and that is the lift arm auto-leveler upward loca-
arm auto-leveler upward locating position,
tion.
earthing of #241 terminal of the MC is released,
and the electromagnet on the lift arm upward end
NOTE: When the lift arm is outside a’, even if the is unexcited. Thus the lift arm operation lever re-
SET position of the lift arm auto-leveler turns to the neutral position, and supply of pres-
upward set switch is selected, setting of the sure oil from the pilot valve to the control valve is
lift arm auto-leveler upward cannot be stopped.
made. In case setting was thus unsuc-
cessful, or setting in a different position is 5. As the lift arm spool of the control valve also re-
needed, make setting again with the above turns to neutral, the lift arm stops at the lift arm
in mind. auto-leveler upward stop position.
T2-1-66
SYSTEM / Control System
PHOTO
Lift Arm
Link Angle Sensor
Lift Arm
Cylinder
Lift Arm
Auto-leveler
Upward Set Switch Control Valve
OFF
234
238
SET
MC
ON 237
Bucket
241
Electromagnet
on Lift Arm Raising End
Pilot
Pump
Hydraulic Oil
Main Tank T4GB-02-01-016
Pump
T2-1-67
SYSTEM / Control System
Lift Arm Auto-leveler Upward Control (Optional)
(ZW250)
Operation:
1. If the SET position of the lift arm auto-leveler 3. Pressure oil from the main pump flows into the
upward set switch is selected after the lift arm is bottom end port of the lift cylinder through the lift
located within the allowable location of the lift arm arm spool of the control valve, and raises the lift
auto-leveler (a’ in the illustration), signal from the arm.
lift arm angle sensor is memorized by the MC,
4. When the lift arm angle sensor moves up to the lift
and that is the lift arm auto-leveler upward loca-
arm auto-leveler upward locating position,
tion.
earthing of #241 terminal of the MC is released,
and the electromagnet on the lift arm upward end.
NOTE: When the lift arm is outside a’, even if the Thus the lift arm operation lever returns to the
SET position of the lift arm auto-leveler neutral position, and supply of pressure oil from
upward set switch is selected, setting of the the pilot valve to the control valve is stopped.
lift arm auto-leveler upward cannot be
made. In case setting was thus unsuc- 5. As the lift arm spool of the control valve also re-
cessful, or setting in a different position is turns to neutral, the lift arm stops at the lift arm
needed, make setting again with the above auto-leveler upward stop position.
in mind.
NOTE: Above the lift arm upward set position, the
electromagnet on the lift arm raising end is
always excited.
T2-1-68
SYSTEM / Control System
Lift Arm
Link Angle Sensor
Lift Arm
Cylinder
Lift Arm
Auto-leveler
Upward Set Switch Control Valve
OFF
234
238
SET
MC
ON 237
Bucket
241
Electromagnet
on Lift Arm Raising End
Pilot
Pump
Hydraulic Oil
Main Tank T4GB-02-01-036
Pump
T2-1-69
SYSTEM / Control System
Lift Arm Auto-leveler Downward Control (Op-
tional)(ZW220)
Operation:
1. If the SET position of the lift arm auto-leveler 3. Pressure oil from the main pump flows into the
downward set switch is selected after the lift arm rod end ports of the lift arm cylinders through the
is located within the allowable location of the lift lift arm spool of the control valve, and lowers the
arm auto-leveler (b’ in the illustration), signal from lift arm.
the lift arm angle sensor is memorized by the MC,
4. When the lift arm angle sensor moves down to the
and that is the lift arm auto-leveler downward lo-
lift arm auto-leveler downward locating position,
cation.
earthing of #242 terminal of the MC is released,
and the electromagnet on the lift arm downward
NOTE: When the lift arm is outside b’, even if the end is unexcited for a while until it is excited again
SET position of the lift arm auto-leveler soon after.
downward set switch is selected, setting of
the lift arm auto-leveler downward cannot 5. Thus the lift arm operation lever returns to the
be made. In case setting was thus unsuc- neutral position, and supply of pilot pressure from
cessful, or setting in a different position is the pilot valve to the control valve is stopped.
needed, make setting again with the above 6. As the lift arm spool of the control valve also re-
in mind. turns to neutral, the lift arm stops at the lift arm
auto-leveler downward stop position.
Position of Position of
Lift Arm Foot Pin Lift Arm Tip Pin
NOTE: In case the lift arm angle sensor becomes
out of order, the lift arm auto-leveler
b’ (Lift Arm
Auto-leveler
downward control is not made.
Downward
Allowable Set- IMPORTANT: In case either the lift arm angle
ting Range)
sensor or the MC has been replaced,
b (Lift Arm Downward be sure to make learning control of
Work Range) the lift arm angle sensor. (Refer to
the OPERATIONAL PERFORMANCE
TEST/Adjustment)
T2-1-70
SYSTEM / Control System
Lift Arm
Cylinder
Bottom End
Port
Rod End
Port
Lift Arm
Auto-leveler Downward
Set Switch
Electromagnet on Bucket
Lift Arm Lowering End
Pilot Valve
for Lift Arm
Lift Arm
From #194 Terminal
of Fuse Box B
Pilot
Pump
T4GB-02-01-017
T2-1-71
SYSTEM / Control System
Lift Arm Auto-leveler Downward Control (Op-
tional)(ZW250)
Operation:
1. If the SET position of the lift arm auto-leveler 3. Pressure oil from the main pump flows into the
downward set switch is selected after the lift arm rod end ports of the lift arm cylinders through the
is located within the allowable location of the lift lift arm spool of the control valve, and lowers the
arm auto-leveler (b’ in the illustration), signal from lift arm.
the lift arm angle sensor is memorized by the MC,
4. When the lift arm angle sensor moves down to the
and that is the lift arm auto-leveler downward lo-
lift arm auto-leveler downwards locating position,
cation.
earthing of #242 terminal of the MC is released,
and the electromagnet on the lift arm downward
NOTE: When the lift arm is outside b’, even if the end is unexcited for a while until it is excited again
SET position of the lift arm auto-leveler soon after.
downward set switch is selected, setting of
the lift arm auto-leveler downward cannot 5. Thus the lift arm operation lever returns to the
be made. In case setting was thus unsuc- neutral position, and supply of pilot pressure from
cessful, or setting in a different position is the pilot valve to the control valve is stopped.
needed, make setting again with the above 6. As the lift arm spool of the control valve also re-
in mind. turns to neutral, the lift arm stops at the lift arm
auto-leveler downward stop position.
Position of Position of
Lift Arm Foot Pin Lift Arm Tip Pin
NOTE: In case the lift arm angle sensor becomes
out of order, the lift arm auto-leveler
b’ (Lift Arm
Auto-leveler
downward control is not made.
Downward
Allowable Set- IMPORTANT: In case either the lift arm angle
ting Range)
sensor or the MC has been replaced,
b (Lift Arm Downward be sure to make learning control of
Work Range) the lift arm angle sensor. (Refer to
the OPERATIONAL PERFORMANCE
TEST/Adjustment)
T2-1-72
SYSTEM / Control System
Lift Arm
Cylinder
Bottom End
Port
Rod End
Port
Lift arm
Auto-leveler Downward
Set Switch
Electromagnet on Bucket
Lift Arm Lowering End
Pilot Valve
for Lift Arm
Pilot
Pump Lift Arm
From #194 Terminal
of Fuse Box B
T4GB-02-01-037
T2-1-73
SYSTEM / Control System
(Blank)
T2-1-74
SYSTEM / ECM System
OUTLINE
Signals from sensors and MC (Main Controller) are • Supply pump is driven by engine and generates
input to ECM (Engine Control Module). high pressure fuel.
ECM calculates and drives two way valve, suction • Common rail distributes high pressure fuel gener-
control valve and EGR motor in order to control supply ated by supply pump to injector of each engine
pump, injectors and EGR (Exhaust Gas Recirculation). cylinder.
• Injector injects high pressure fuel from common
• Fuel Injection Control rail.
• Engine Start Control
• EGR Control
• Correction of Fuel Injection Volume
• Engine Stop Control (Refer to System/Electric
System)
Crank Revolution Sensor
EGR Motor
ECM
MC
Suction Control
Valve
Common Rail
Supply Pump
Injector
Fuel Tank
T4GB-02-02-022
T2-2-1
SYSTEM / ECM System
FUEL INJECTION CONTROL
EGR Motor
ECM
MC
Suction Control
Valve
Common Rail
Supply Pump
Injector
Fuel Tank
T4GB-02-02-022
T2-2-2
SYSTEM / ECM System
(Blank)
T2-2-3
SYSTEM / ECM System
Fuel Injection Volume Control
Operation:
1. ECM detects engine speed according to input
signals from crank revolution sensor and cam
angle sensor.
2. MC calculates target engine speed according to
input signals from sensors and switches. MC
sends signal to ECM. (Refer to System/Control
System.)
3. ECM turns two way valves in the injectors into ON
or OFF mainly according to the engine speed and
signal from MC in order to control fuel injection
volume.
T2-2-4
SYSTEM / ECM System
Accelerator
Pedal Sensor Crank Revolution Sensor
MC ECM
Monitor
Unit
Common
Rail
Supply Pump
T4GC-02-02-004
T2-2-5
SYSTEM / ECM System
Fuel Injection Pressure Control Fuel Injection Timing Control
Function: Controls fuel injection pressure according Function: Calculates appropriate fuel injection timing.
to fuel pressure in common rail.
Operation:
Operation: 1. ECM calculates fuel injection timing according to
1. ECM calculates fuel injection volume according to engine speed and fuel injection volume.
engine speed and target engine speed signal of 2. ECM drives ON/OFF of two way valves in injec-
MC. (Refer to Page T2-2-4). tors in order to control fuel injection timing.
2. Common rail pressure sensor sends signal cor-
responding to pressure in common rail to ECM. Fuel Injection Volume Control
3. ECM calculates appropriate pressure in common
rail according to engine speed, fuel injection
volume and common rail pressure sensor signal. Function: Improves combustion inside the engine
ECM drives suction control valve in supply pump cylinders.
and appropriate volume of fuel to common rail.
4. Fuel in common rail is supplied to each engine Operation:
cylinder through injector from common rail. 1. Injectors initially inject small amount of fuel (pilot
injection) for ignition.
NOTE: Mode switches of the work mode switch 2. Injectors execute the second injection (main in-
are supplied with respectively different jection) after ignition. ECM drives ON/OFF of two
voltages from the monitor unit. MC judges way valves in injectors in order to control fuel in-
the selected mode by the supplied voltage. jection timing and volume.
T2-2-6
SYSTEM / ECM System
Accelerator
Pedal Sensor Crank Revolution Sensor
MC ECM
Common
Rail
Supply Pump
T4GC-02-02-005
T2-2-7
SYSTEM / ECM System
Fuel Injection
1. Fuel pressure is constantly applied to the injector
nozzles.
2. When the magnetic coil of the two-way valve is
turned ON, the valve is opened, and the
high-pressure fuel in the control chamber returns
to the fuel tank through Orifice 1.
3. Spring force raises the hydraulic piston, and the
nozzle is opened to start injection.
4. When the magnetic coil of the two-way valve is
turned OFF, the valve is closed, and the circuit
leading to the fuel tank is closed.
5. In this way, the control chamber is filled with
high-pressure fuel.
6. Difference of top and bottom pressure of the pis-
ton lowers the piston, and the nozzle is closed to
finish injection.
T2-2-8
SYSTEM / ECM System
1. Two Way Valve: ON 2. Fuel Injection Start
From ECM From ECM
Magnetic Coil
Two Way Valve Two Way Valve
Valve
Return to Fuel Return to Fuel
Tank Tank
From Common Rail From Common
Rail
Orifice 1
Spring
Spring
Nozzle Nozzle
Magnetic Coil
Two Way Valve Two Way Valve
Valve
Control Chamber
Hydraulic Piston
Orifice 2
Nozzle Nozzle
T1GR-02-02-012C
T2-2-9
SYSTEM / ECM System
COMPENSATION OF FUEL INJECTION
VOLUME Atmospheric Pressure Sensor
Two Way
Valve
T1GR-02-02-002C
T2-2-10
SYSTEM / ECM System
ENGINE START CONTROL
Coolant Temperature
Sensor From Key Switch
Function: Controls energizing time of glow plugs by Terminal M
coolant temperature and improves start-
ability of engine.
Operation:
1. Coolant temperature sensor sends signal corre-
sponding to coolant temperature to ECM. ECM
2. ECM connects the ground circuit of glow relay
according to signals and controls energizing time
of glow plugs.
Glow Relay
From Battery
Relay
T2-2-11
SYSTEM / ECM System
EGR (EXHAUST GAS RECIRCULATION)
CONTROL
Operation:
• EGR Gas Amount Control
1. ECM determines amount of EGR gas according
to engine speed, fuel flow rate, coolant tempera-
ture, atmospheric pressure and intake air tem-
perature.
2. ECM drives the EGR motor, and opens the EGR
valve. And transfer the EGR gas corresponding to
the engine condition to the intake manifold to be
mixed with the intake air.
3. At the same time, EGR motor position sensor
detects amount of opening of EGR valve.
T2-2-12
SYSTEM / ECM System
To Intercooler
Exhaust Gas
Coolant Out
Coolant System
Engine
Coolant In
EGR Valve
Intake
Manifold EGR Motor
Position Sensor
From Intercooler
EGR Motor
Lead Valve
Intake Air
ECM
T1GR-02-02-011
T2-2-13
SYSTEM / ECM System
(Blank)
T2-2-14
SYSTEM/Hydraulic System
OUTLINE
• Main Circuit
Main circuit consists of the priority valve circuit,
neutral circuit, single operation circuit, and
combined operation circuit – composed of the
main pump, priority valve, control valve, cylinders,
etc.
• Pilot Circuit
Pilot circuit consists of the charging block circuit,
front attachment operation control circuit, pump
control circuit, brake circuit, and ride control circuit
(optional) – composed of the pilot pump, charging
block and valves for controlling each circuit.
• Steering Circuit
Steering circuit consists of the normal steering
circuit, steering shock damping circuit,
emergency steering circuit (optional), steering
stop circuit– composed of the pump, priority valve,
steering valve, cylinders, and other valves.
T2-3-1
SYSTEM/Hydraulic System
MAIN CIRCUIT
Outline
• Main pump draws hydraulic oil from the hydraulic
oil tank through the suction filter and delivers.
T2-3-2
SYSTEM/Hydraulic System
PHOTO PHOTO
Control Valve
Bucket
Spool
Steering
Valve
Lift Arm
Spool
Priority
Valve
Main Pump
T4GB-02-02-010
T2-3-3
SYSTEM/Hydraulic System
Priority Valve Circuit
• With the engine stopped, the priority valve spool • When pressure at Port LS2 and the spring force
is pushed leftward by the spring force. overcome pressure at Port LS1, the priority valve
• When the engine is started, pressure oil from the spool moves left.
main pump flows toward the steering valve • Larger the movement of the steering valve spool
through the priority valve spool, while also is, the higher the pressure at Port LS2 rises, the
entering Ports LS1 and LS2 through Orifices 1 larger the priority valve spool moves left, and the
and 2 respectively. more pressure oil from the main pump is supplied
• With the steering valve in neutral, pressure oil led to the steering valve.
to Port LS2 flows to the hydraulic oil tank through
Orifice 3 and the steering valve spool, so Port LS2 NOTE: Orifice 2 of the priority valve is installed for
is not pressurized. warming up the circuit by flowing pressure
• As pressure at LS1 causes larger force than the oil to the hydraulic oil tank from Port LS2 at
spring force, the priority valve spool moves right, neutral of the steering valve. Diameter of
and pressure oil from the main pump is all Port 2 is small, and temperature of the oil
supplied to the control valve. passing through it rises rapidly, but
• Priority valve spool is provided with a notch for pressure is not raised enough to influence
leading pressure oil from the main pump toward movement of the priority valve spool.
the steering valve and a notch for leading
pressure oil from the main pump toward the
control valve, which are both connected to the
main pump delivery port constantly.
• When the priority valve spool moves right, the
notch for leading pressure oil from the main pump
toward the steering valve moves until the delivery
port on the steering valve side in the priority valve
is closed. When pressure balance is obtained and
the spool stops moving.
• When the steering valve spool moves, the tank
port connected with Port LS2 is closed.
• At this time, Port LS2 is connected with the main
circuit through the steering valve spool, and
pressure corresponding to movement of the
steering valve spool arises at Port LS2.
T2-3-4
SYSTEM/Hydraulic System
Lift Arm
Cylinders
Hydraulic
Oil Tank
Bucket
Spool
Hydraulic
Oil Tank
Lift Arm
Hydraulic
Oil Tank
Priority Spring
Valve Orifice 2
Orifice 1
Orifice 3
LS1
Spool LS2
Main Pump At Stop of Engine T4GB-02-02-011
T2-3-5
SYSTEM/Hydraulic System
Neutral Circuit
• At neutral position of the control lever, pressure oil
from the main pump returns to the hydraulic oil
tank through the neutral circuit of the control
valve.
• Only when the steering valve spool moves
actuated by the priority valve, pressure oil is
supplied to the steering valve, the steering valve
is not provided with a neutral circuit. (Refer to
Priority Valve Circuit in this section.)
T2-3-6
SYSTEM/Hydraulic System
Lift Arm
Cylinders
Bucket
Lift Arm
Priority
Valve
T2-3-7
SYSTEM/Hydraulic System
Combined Operation Circuit (ZW220)
T2-3-8
SYSTEM/Hydraulic System
Steering Cylinders
Bucket Cylinder
Lift Arm
Cylinders
Bucket From
Pilot
Valve
(Bucket
Orifice Dump)
Hydraulic
Oil Tank
From Pilot Valve Lift Arm
(Lift Arm Raise)
Check Valve
Hydraulic
Oil Tank
Spring
Priority
Valve
LS2
LS1
Spool
T2-3-9
SYSTEM/Hydraulic System
· Lift Arm Raising/Steering Right
• When the steering wheel is turned right with the
lift arm raised, pilot pressure shifts the lift arm
spool in the control valve and the steering valve
spool.
• Pressure from the main pump is applied to Port
LS1 of the priority valve through Orifice 1, and
main pressure returning from the steering valve
spool through Orifice 3 and the spring force are
applied to Port LS2.
• Pressure at Port LS2 changes in proportion to the
steering valve spool stroke, and when pressure at
Port LS2 is low, the priority valve spool moves left
slightly, and when it is high, the spool moves left
drastically.
• Flow rate and direction of the main pump are
controlled by the leftward stroke of the priority
valve spool, and the flow rate corresponding to
the stroke flows to the steering valve, and the
remainder flow rate flows to the control valve.
T2-3-10
SYSTEM/Hydraulic System
Lift Arm
Cylinders
Hydraulic
Oil Tank
From Steering
Pilot Valve Bucket
(Right Steering)
Spool Hydraulic
Oil Tank
From Pilot Lift Arm
Valve
(Lift Arm Raise)
Check Valve
Hydraulic
Oil Tank
Spring
Priority Valve
Orifice 2
Orifice 1 Orifice 3
LS1
Spool LS2
T2-3-11
SYSTEM/Hydraulic System
Combined Operation Circuit (ZW250)
T2-3-12
SYSTEM/Hydraulic System
Steering Cylinders
Bucket Cylinder
Lift Arm
Cylinders
Bucket
Selector Valve
Priority
Valve
LS2
LS1
T2-3-13
SYSTEM/Hydraulic System
· Lift Arm Raising/Steering right
• When the steering wheel is turned right with the
lift arm raised, pilot pressure shifts the lift arm
spool in the control valve and the steering valve
spool.
• Pressure from the main pump is applied to Port
LS1 of the priority valve through Orifice 1, and
main pressure returning from the steering valve
spool through Orifice 3 and the spring force are
applied to Port LS2.
• Pressure at Port LS2 changes in proportion to the
steering valve spool stroke, and when pressure at
Port LS2 is low, the priority valve spool moves left
slightly, and when it is high, the spool moves left
drastically.
• Flow rate and direction of the main pump are
controlled by the leftward stroke of the priority
valve spool, and the flow rate corresponding to
the stroke flows to the steering valve, and the
remainder flow rate flows to the control valve.
T2-3-14
SYSTEM/Hydraulic System
Lift Arm
Cylinders
Hydraulic
Oil Tank
From Steering Bucket
Pilot Valve
(Right Steering)
Spool
Hydraulic
Oil Tank
Lift Arm
From Pilot
Valve
(Left Arm
Raise)
Check Valve
Hydraulic
Oil Tank
Spring
Priority Valve
Orifice 2
Orifice 1 Orifice 3
LS1
Spool LS2
T2-3-15
SYSTEM/Hydraulic System
(Blank)
T2-3-16
SYSTEM/Hydraulic System
PILOT CIRCUIT
Outline:
Pressure oil from the pilot pump is used to operate the • Pump Control Circuit
circuit below. • Brake Circuit
• Charging Block Circuit • Ride Control Circuit (Optional)
• Front Attachment Operation Control Circuit
Front Attachment
Control Circuit
Control Valve
Brake Service
Valve Brake
Brake Circuit
Parking
Brake
Hydraulic
Pilot Pilot Suction Oil
Filter Pump Filter Tank
T4GC-02-02-001
T2-3-17
SYSTEM/Hydraulic System
Charging Block Circuit
• Charging block is installed for supplying pressure
oil from the pilot pump preferentially to the service
brake circuit, while distributing it to other pilot
circuits as well.
• When the engine is started, oil is delivered from
the pilot pump, and enters the charging block.
• At this time, when the amount of accumulated
pressure of the service brake accumulators is low,
the relief valve keeps closed.
• In this case, only pilot pressure is applied to Port
B of the priority valve, but both the pilot pressure
and the spring force are applied to Port A. So, the
priority valve moves right, restricting pressure oil
to flow further.
• Pressure oil from the pilot pump flows toward the
service brake circuit through the check valve, and
accumulates the service brake accumulators.
T2-3-18
SYSTEM/Hydraulic System
Service Brake
Brake
Pedal Front Brake
Service Brake
Accumulators
Check
Valves
Relief Valve
B
Priority
Valve
Charging Block
T2-3-19
SYSTEM/Hydraulic System
• When the service accumulators are pressurized
to a certain amount, the relief valve opens, and
pressure is lost because Port A of the priority
valve is connected to the hydraulic oil tank.
• Pressure at Port B of the priority valve causes
larger force than the spring force, and moves the
priority valve spool left. So, pressure oil from the
pilot pump is all supplied to the priority valve and
the circuits downstream.
• Pressure oil from the priority valve is supplied
through each port to the respective pilot circuits.
• When pressure in the pilot circuit rises higher than
a certain amount, the pilot relief valve opens, and
prevents components of the pilot circuit from
being damaged.
• Pressure oil from Port PS1 passes the steering
pilot valve to be supplied for actuation of the
steering valve spool. (Refer to Steering Circuit.)
• Pressure oil from Port X changes its flow in
response to the stroke of the pump torque
control solenoid valve which is controlled by the
signal from MC, and is used for controlling the
main pump regulator.
(Refer to Pump Control Circuit.)
• Pressure oil from Port BR3 is supplied for parking
brake release pressure by operation of the
parking brake solenoid valve. (Refer to Parking
Brake Circuit)
• Pressure oil from Port PS2 is supplied for
controlling the servo piston of the main pump
(Refer to Pump Control Circuit.) and the spool of
the ride control valve (Refer to Ride Control
Circuit.).
• Pressure oil from Port PP enters each pilot valve
through the pilot shutoff valve, and is supplied to
the control valve for actuation of the spool. (Refer
to Front Attachment Operation Control Circuit.)
T2-3-20
SYSTEM/Hydraulic System
PHOTO
Pilot Valve
Bucket Lift Arm Spare Pilot
Pilot Valve Pilot Valve Valve (Optional) 018
To Service Brake
Circuit
Service Brake
Accumulators
Priority Valve
Relief Valve
B
Pilot Pump
Pilot
Relief Valve
A Hydraulic Oil Tank
PS1
Spring X Parking Brake
Pump Torque Control Pressure Sensor
BR3
Solenoid Valve
PS2
Parking Brake
Solenoid Valve
PP
T4GB-02-02-020
Charging Block
T2-3-21
SYSTEM/Hydraulic System
Front Attachment Operation Control Circuit
(ZW220)
T2-3-22
SYSTEM/Hydraulic System
1 2 3 4 5 6 7 8
Control Valve
Pilot Shutoff
Valve
Spare 2
8
7
To Service Brake
Circuit
Service Brake
Accumulators Spare 1
6
5
Priority Valve
Bucket
2
1
Slow-Return
Pilot Pump Valves
Lift Arm
4
3
Main Pump
PP
T4GB-02-02-002
Charging Block
T2-3-23
SYSTEM/Hydraulic System
Front Attachment Operation Control Circuit
(ZW250)
T2-3-24
SYSTEM/Hydraulic System
1 2 3 4 5 6 7 8
Control Valve
Pilot Shutoff Valve
Spare 2
8
7
To Service Brake
Circuit
Service Brake
Accumulators Spare 1
6
5
Priority Valve
Bucket
2
1
Slow-Return
Pilot Pump Valves
Lift Arm
4
3
Main Pump
PP
Charging Block T4GB-02-02-021
T2-3-25
SYSTEM/Hydraulic System
Pump Control Circuit
(Refer to COMPONENT OPERATION / Pump
Device group)
T2-3-26
SYSTEM/Hydraulic System
PS2
Pi1
Servo
Main Pump Piston
Regulator
T2-3-27
SYSTEM/Hydraulic System
Brake Circuit
T2-3-28
SYSTEM/Hydraulic System
PHOTO PHOTO
Service Brake
Brake
Pedal Front Brake
Service Brake
Accumulators
Check
Valves
Relief Valve
Priority
Valve
Spring
T2-3-29
SYSTEM/Hydraulic System
Ride Control Circuit (Optional)
(Refer to SYSTEM / Electric-Hydraulic Combined
Circuit Control in Control System)
T2-3-30
SYSTEM/Hydraulic System
PHOTO
Ride Control
099
To Control
Valve
Ride Control
Command Signal
Ride Control
Solenoid Valve
Spool
Pilot T4GB-02-02-009
Pump
T2-3-31
SYSTEM/Hydraulic System
STEERING CIRCUIT
T2-3-32
SYSTEM/Hydraulic System
Steering System
Steering 076 077 078 079
Accumulators
Steering Valve
Spool
Orifice
Orifice
Pump
Discharge Pressure
Switch
To Control
Steering Valve
Pilot
Gerotor
Valve Priority
Valve Emergency
Steering
Pump Equipment
LS2
Steering LS1
Wheel
T2-3-33
SYSTEM/Hydraulic System
Steering Shock Damping Circuit
• Pressure of the pressure oil supplied from the
steering pilot valve to the spool end of the
steering valve is reduced by passing through the
orifice inside the steering valve, and is applied to
the spool end of the opposite side. In this way, the
vehicle shock due to sudden shift of the spool is
damped, and stable steering operation is possible.
(Refer to COMPONENT OPERATION / Steering
Valve)
• Steering accumulators are provided for damping
the joggling of the vehicle taking place at stop of
the steering wheel rotation.
T2-3-34
SYSTEM/Hydraulic System
Steering Cylinders
Steering
Accumulators
Steering Valve
Orifice
Orifice
Pump
Delivery Pressure
Switch
Emergency
To Control Steering
Steering Valve Pump Delivery
Pilot Pressure Sensor
Gerotor
Valve Priority
Valve Emergency
Steering
Pump Equipment
LS2
Steering LS1
Wheel
T2-3-35
SYSTEM/Hydraulic System
Steering Stop Circuit
(Refer to COMPONET OPERATION / Steering
Valve)
• When either of the left or right cylinder is at the • As a result, the steering valve spool is shifted at
stroke end, the stop valve spool contacts the neutral, and supply of pressure oil from the main
frame, and the stop valve closes to block pump to the steering cylinders is stopped.
pressure oil from being supplied to the steering
valve from the steering pilot valve.
Steering Cylinders
PHOTO
Steering System
077
Steering Valve
Spool
Stop Stop
Valve Valve
External Force
Applied
Steering
Pilot Valve
Main Pump
Pilot Pump
Hydraulic
Oil Tank T4GB-02-02-00
T2-3-36
SYSTEM/Hydraulic System
(Blank)
T2-3-37
SYSTEM/Hydraulic System
HYDRAULIC DRIVE FAN CIRCUIT
(Refer to COMPONET OPERATION / Others)
(Refer to COMPONET OPERATION / Hydraulic Fan
Motor)
T2-3-38
SYSTEM/Hydraulic System
PHOTO
Fan Motor
Cooling Fan
039
Reverse Rotation
Signal from MC
Flow Control Valve
Flow Adjustment
Signal from MC
T2-3-39
SYSTEM/Hydraulic System
(Blank)
T2-3-40
SYSTEM/Electric System
OUTLINE
· Main Circuits
Circuit for engine start/stop, circuit for battery
charging, and circuit for accessories.
· Lamplight Circuits
Circuit for use in traveling (composed of head lights,
turn signals, brake lights, and horn)
T2-4-1
SYSTEM/Electric System
MAIN CIRCUIT
T2-4-2
SYSTEM/Electric System
ELECTRICAL POWER CIRCUIT (KEY
SWITCH:OFF)
Ground terminal of the battery is earthed to the base Even at OFF of the key switch, very small amount of
machine. Electrical current from the plus positive flows electrical current is being supplied to the circuit, so the
as follows at OFF of the key switch. ground terminal of the battery needs to be
disconnected in case of a long downtime.
Fuse Box B
348
149
126
6
11
9 638
35 34
158
127 263
2
7 70
39
42 710
37
381
711 75
Battery
Fusible Relay Battery
Link
T4GC-02-04--001
T2-4-3
SYSTEM/Electric System
INDICATOR LIGHT CHECK CIRCUIT (KEY
SWITCH:ON)
• When the key switch is turned ON, Terminal B is • Monitor unit checks warning lamps and indicators
connected inside the key switch to ACC and by lighting them, and also starts the liquid crystal
Terminal M. display.
• Electrical current from Terminal M of the key
switch is enters #67 Terminal of the monitor unit.
Key Switch
Fuse Box B
348 838
149
577 148
327
222
323 126
6
11
9 638
35 34
158
127 263
2
Monitor Unit
711 75
67
Battery
Fusible Relay Battery
Link
T4GB-02-03-002
T2-4-4
SYSTEM/Electric System
ACCESSORY CIRCUIT
Key Switch
Fuse Box B
348 838
Radio 149
577 148
327
222
323 126
6
11
9 638
35 34
158
127
2
711 75
Battery
Fusible Relay Battery
Link
T4GB-02-03-003
T2-4-5
SYSTEM/Electric System
PREHEAT CIRCUIT (KEY SWITCH:ON)
T2-4-6
SYSTEM/Electric System
PHOTO
Fusiable Links
Key Switch
032
Fuse Box A
264
362
692 157
From #6 Terminal
of Fuse Box B
55 54
163
693 79
108
12 99
698
699
700 697
Glow Relay
Monitor
。 Unit
Glow
Glow Plug Signal
233
Coolant Temperature
Sensor 60
56
283
284
233
Fuse Battery
(100A) Fusible Relay
Link ECM
To #638 Terminal of
Fuse Box B Battery
T4GB-02-03-004
T2-4-7
SYSTEM/Electric System
STARTING CIRCUIT (KEY SWITCH:
START)
Starter Relay
S B
D3
(1) L
R4
C
R3 (2)
(1)
R2 Z S
D2
From Terminal L R Q2 M
Q1 B
of Alternator
C1 (2)
C
Starter
E
D4
12V
B
ST Battery
T4GB-02-03-019
T2-4-8
SYSTEM/Electric System
Key Switch
264
Fuse Box A
362
From #6 Terminal 692 157
of Fuse Box B
Signal of Key ON
to (Monitor Unit) 464
Signal of Key ON to 55 54
(MC, ECM, and ICX) 163
693 79
108
12 99
699
700 697
No Forward/Reverse Signal
Neutral Relay
To #638 Terminal
of Fuse Box B
Starter Fuse
Relay (100A)
Battery
Fusible Relay
Link
Battery
Starter
Motor
Alternator T4GC-02-04--002
T2-4-9
SYSTEM/Electric System
Forward/Reverse Lever at Operational Position
· Starting Safety Circuit (Neutral Relay)
• At START of the key switch, Terminal B can be
connected inside the key switch to Terminals M
and ST.
• Electric current from Terminal ST of the key switch
flows to the neutral relay, and the electric current
from Terminal M of the key switch flows to the
Terminals #54 and #55 of Fuse Box A then excites
the battery relay.
• By exciting the battery relay, electricity from the
battery power source flows to Terminals B of the
starter motor and the starter relay.
• At this moment, either of the forward-reverse
lever and the forward-reverse switch is at forward
or reverse, the neutral relay is excited.
• Circuit between the neutral relay and Terminal S
of the starter relay is blocked by excites the
neutral relay.
• Therefore, in case either of the forward-reverse
lever and the forward-reverse switch is at forward
or reverse, the starter motor is not operated even
if the key switch is at START.
T2-4-10
SYSTEM/Electric System
Key Switch
Fuse Box A
264
362
692 157
210
From #6 Terminal
of Fuse Box B 464
55 54
163
693 79
108
12 99
698
699
Forward/Reverse 700 697
Operation Signal
Neutral Relay
To #638 Terminal
of Fuse Box B
Starter Fuse
Relay (100A)
Battery
Fusible Relay
Link
Battery
Starter
Motor
T4GB-02-03-006
T2-4-11
SYSTEM/Electric System
CHARGING CIRCUIT (KEY SWITCH:ON)
T2-4-12
SYSTEM/Electric System
PHOTO
Alternator
Key Switch
034
Fuse Box A
264
362
From #6 Terminal 692 157
of Fuse Box B
464
Alternator Monitor 55 54
Indicator Unit
163
592 693 79
GPS 108
12 99
144
119 594 133
ICX 121 120
696
695 674
698
699
700 697
To #638 Terminal
of Fuse Box B
Fuse
Starter
(100A)
Relay
Battery
Fusible Relay
Link
Battery
Starter
Motor
T4GB-02-03-007
Alternator
T2-4-13
SYSTEM/Electric System
Operation of Alternator
• Alternator consists of Field Coil FC, Stator Coil SC, • At first, electric current is not flowing to Field Coil
Diode D, and others. FC. When the rotor rotates, alternating voltage is
• Regulator consists of Transistors T1 and T2, Zener generated in Stator Coil SC by the remanent
Diode ZD, Resistances R1 and R2, and others. magnetism of the rotor itself.
• Terminal B of the alternator is connected to Base • Electric current flows to Field Coil FC, and further
B of Transistor T1 as follows. magnetizes the rotor, resulting in rise of electric
• B - R - RF - (R) - R1 - Base B of Transistor T1 generation voltage. This further raises electric
• At On of the battery relay, the battery voltage generation voltage, and charging the battery
works on Base B of Transistor T1 of the regulator, begins.
and continuity is made between Collector C and
Emitter E. In other words, the earth end of Field
Coil FC is grounded through Transistor T1.
Alternator
B R L
Regulator
Battery Relay RF (R) R3 R4 R5
R6
D
ZD
R2
Battery SC B
E
R1 C
FC T2
B
D1 C E
T1
(F)
(G)
G
T157-04-02-008C
T2-4-14
SYSTEM/Electric System
Operation of Regulator
• As electric generation voltage rises higher than • If voltage working on Zener Diode ZD lowers
the set voltage of Zener Diode ZD, electric current below the set voltage, Transistor T2 is turned OFF,
flows to Base B of Transistor T2, and continuity is and Transistor T1 is turned ON again.
made between Connector C and Emitter E. • Electric current flows to Field Coil FC, and electric
• Operation of Transistor T2 stops flow of the generation voltage of Stator Coil SC is raised.
electric current to Base B of Transistor T1, and • Electric generation voltage of the alternator is
turns T1 OFF. kept constant by repeating the above operations.
• Electric current stops flowing to Field Coil FC, and
electric generation voltage of Stator Coil SC
lowers.
Battery Relay RF R3 R4 R5
R6
ZD
R2
Battery SC B
A E
C
T2
FC B
R1 E
C
D1 T1
(F)
(G)
G
T157-04-02-009
T2-4-15
SYSTEM/Electric System
SURGE VOLTAGE PREVENTION CIRCUIT
T2-4-16
SYSTEM/Electric System
Key Switch
Load Dump
Relay
Fuse Box B
33
348 838
Monitor 149
Unit 577 148
327
119
222
323 126
6
11
9 638
35 34
158
127 263
2
7 70
39
42 710
37
381
711 75
Fuse
Starter (100A)
Relay
Battery
Fusible Relay
Link
Battery
Starter
Motor
T4GB-02-03-008
Alternator
T2-4-17
SYSTEM/Electric System
ENGINE STOP CIRCUIT
• When the key switch is turned OFF from ON, the • ECM unexcited the fuel injection solenoid valve,
electric current flowing from Terminal M to #56 and the engine is stopped.
Terminal of the ECM to show the key switch at ON
is stopped.
Key Switch
Fuse Box A
264
362
692 157
From #6 Terminal 210
of Fuse Box B
55 54
163
80 79
108
12 99
698
699
700 697
To #638 Terminal
of Fuse Box B
56
Fuse
Fuel Injection (100A)
Solenoid Valve Battery
ECM
Fusible Relay
Link
Battery
T4GB-02-03-009
T2-4-18
SYSTEM/Electric System
LAMPLIGHT CIRCUIT
T2-4-19
SYSTEM/Electric System
HEAD LIGHT CIRCUIT
T2-4-20
SYSTEM/Electric System
Key Switch
Front Right
Clearance Light Fuse Box B
Rear Right 348 838
Clearance Light 149
577
126
6
11
9 638
35 34
158
127 263
2
7 70
39
42 710
37
License 381
Light
711 75
Rear Left
Clearance Light
Fusible
Link
Front Left
Clearance Light
Battery
T4GB-02-03-010
Battery Relay
T2-4-21
SYSTEM/Electric System
Head Light Lighting Circuit
• When the key switch is turned ON, the electricity
from the power source coming out of Terminal M
of the key switch excites the battery relay through
#54 and #55 Terminals of Fuse Box A, and the
electricity from the battery power source flows to
Fuse Box A and Fuse Box B.
• Electricity from the battery power source coming
out of #124 Terminal of Fuse Box A enters the
right head light relay.
• Electricity from the battery power source coming
out of #121 Terminal of Fuse Box A enters the left
head light relay.
• Electricity from the battery power source coming
out of #127 Terminal of Fuse Box B enters the
high beam relay.
• When the head light switch is positioned at
(Head Lights), the electricity from the power
source coming out of Terminal S lights each of the
clearance lights (Refer to Clearance Light
Lighting Circuit.), and the electricity from the
power source coming out of Terminal H flows to
the high-low beam switch.
• At this moment, if the high-low beam switch is
turned to Lo (Low Beam), the electricity from the
power source enters the right head light relay and
the left head light relay, and the electricity from
the battery power source enters the head lights to
light them by exciting the respective relays.
• If the high-low beam switch is turned to Hi (High
Beam), the electricity from the power source
excites the high-beam relay, and the electricity
from the battery power source enters and lights
the high-beam lights. Electricity from the power
source coming out of the high-low beam switch
also enters #130 Terminal of the monitor unit, and
lights the high-beam indicators.
T2-4-22
SYSTEM/Electric System
Key Switch
Lo
Hi
Fuse Box A
Monitor
Unit 264
362
High-Beam 692 157
Indicator High-Beam Right Head Light Left Head Light 210
Relay Relay Relay 124
135 123
130
55 54
63
163
121 120
696
695 694
698
699
700 697
Fuse Box B
348 838
149
577
Right High-Beam Light
126
6
11
9 638
Right Head Light 35 34
158
127 263
2
7 70
Left High-Beam Light 39
42 710
37
381
711 75
Left Head Light
Fusible
Link
Battery
T4GB-02-03-018
Battery Relay
T2-4-23
SYSTEM/Electric System
TURN SIGNAL CIRCUIT
• Electricity from the battery power source also • Electricity from the power source coming out of
flows to the flasher relay coming out of #11 the flasher relay enters the front and rear left turn
Terminal of Fuse Box B. signal lights and #23 Terminal of the monitor unit
• In case the turn signal switch is turned to left (L), through the left turn signal relay.
Terminal L of the turn signal switch is earthed, and • As a result, front and rear left turn signal lights
the left turn signal relay is excited. and the left turn signal indicators flicker.
Monitor
Unit
Left Left Right
Turn Signal Turn Signal Relay Turn Signal Flasher
Relay Relay Fuse Box B
Right 348 838
Turn Signal 23 149
577 148
327
26 222
323 126
6
11
9 638
35 34
158
127
Rear Right 2
Turn Signal Light
711 75
Front Right
Turn Signal
Rear Left
Turn Signal
Battery
T4GB-02-03-011
T2-4-24
SYSTEM/Electric System
BRAKE LIGHT CIRCUIT
• When the key switch is turned ON, the electricity • When the brake pedal is stepped, the brake light
from the power source coming out of Terminal M switch is earthed.
of the key switch excites the battery relay, and the • As a result, the brake light relay is excited, and
electricity from the battery power source enters the electricity from the battery power source
#99 Terminal of Fuse Box A and the brake light enters the brake lights, and light them.
relay through #12 Terminal.
Key Switch
PHOTO
Pedals
007
From #6 Terminal
of Fuse Box B
55 54
163
693 79
108
12 99
144
133
121 120
Right Brake Light 696
695 694
698
699
700 697
To #638 Terminal
of Fuse Box B
T4GB-02-03-012
T2-4-25
SYSTEM/Electric System
HAZARD LIGHT CIRCUIT
• Electricity from the battery power source also • Electricity from the power source coming out of
flows to the flasher relay coming out of #11 the flasher relay enters all of the front and rear left
Terminal of Fuse Box B. and right turn signal lights and #23 and #26
• In case the hazard switch is turned ON, the Terminals of the monitor unit through the left and
hazard switch is earthed, and the left and right right turn signal relays.
turn signal relays are excited. • As a result, all of the front and rear left and right
turn signal lights and the left and right turn signal
indicators flicker.
Diode Diode
B D
Monitor
Unit
Left Left Turn Right Turn
Turn signal Signal Relay Signal Relay Flasher
Relay Fuse Box B
Right 348 838
Turn signal 23 149
577 148
327
26
222
323 126
6
11
9 638
35 34
158
127 263
Rear Right 2
Turn Signal Light
7 70
39
42 710
Front Right 37
Turn Signal Light 381
711 75
Rear Left
Turn Signal Light
Battery
T4GB-02-03-013
T2-4-26
SYSTEM/Electric System
HORN CIRCUIT
• When the key switch is turned ON, the electricity • Horn switch is earthed when pushed.
from the power source coming out of Terminal M • As a result, the horn relay is excited, and the
excites the battery relay through #54 and #55 electricity from the battery power source enters
Terminals of Fuse Box A, and the electricity from the horn, and the horn sounds.
the battery power source enters #120 Terminal of
Fuse Box A and the horn relay through #133
Terminal.
Key Switch
From #6 Terminal
of Fuse Box B
Fuse Box A
264
362
692 157
Horn Relay 210
124
Horn 135 123
Switch
55 54
163
693 79
108
12 99
144
133
121 120
696
695 694
698
Horn 699
700 697
Battery
Relay
Fusible
Link
Battery
To #638 Terminal
of Fuse Box B
T4GB-02-03-014
T2-4-27
SYSTEM/Electric System
REVERSE LIGHT/BUZZER CIRCUIT
T2-4-28
SYSTEM/Electric System
Forward/Reverse Lever
Key Switch
From #6 Terminal
of Fuse Box B
Fuse Box A
264
362
692 157
Reverse 210
Light 124
MC Relay 135 123
84
55 54
109 163
693 79
108
12 99
144
133
121 120
696
695 694
698
699
700 697
Right Reverse Light
Reverse Buzzer
Battery
Fusible Relay Battery
Link
To #638 Terminal
of Fuse Box B
T4GC-02-04-003
T2-4-29
SYSTEM/Electric System
PARKING BRAKE CIRCUIT
• When the key switch is turned ON, the electricity • However, as a self-exciting circuit is formed in
from the power source coming out of Terminal M Parking Brake Relay 2, electric current keeps
excites the battery relay through #54 and #55 flowing to the parking brake solenoid valve,
Terminals of Fuse Box A. keeping the released condition of the parking
• Electricity from the power source enters #79 brake until the key switch is turned OFF or the
Terminal of Fuse Box A and Parking Brake Relay parking brake switch is turned ON.
1 through #163 Terminal of Fuse Box A.
• Electricity from the power source coming out of IMPORTANT: Parking brake cannot be released
Terminal D of Parking Brake Relay 1 through unless the engine is running.
Terminal B of Parking Brake Relay 1 flows to
Terminal B of Parking Brake Relay 2 and Terminal • When the parking brake switch is turned ON,
B of the parking brake switch. Terminal A of the parking brake switch is earthed,
• Parking brake switch is composed of three circuits and Parking Brake Relay 1 is excited.
of ON, NEUTRAL, and OFF, and so constructed • Electricity from the power source having been
as to remain at ON when turned ON, but to supplied to Terminal B of Parking Brake Relay 2
automatically return to NEUTRAL when turned and Terminal B of Parking Brake Switch through
OFF. Terminal D of Parking Brake Relay 2 is blocked.
• When the parking brake switch is turned OFF, • As a result, the parking brake works because
electric current flows from Terminal E of the Parking Brake Relay 2 and the parking brake
parking brake switch to Terminal A of Parking solenoid valve are unexcited.
Brake 2 and the parking brake solenoid valve.
• At this moment, if the engine is not running,
Parking Brake Relay 1 is excited because #684
Terminal of the monitor unit is earthed.
• Therefore, the parking brake cannot be released
because the electricity from the power source
having been supplied through Parking Brake 1 to
Terminal B of the parking brake switch and
Terminal B of the parking brake relay is blocked.
• In case the engine is running, Parking Brake
Relay 2 is excited because the electric current
from Terminal L of the alternator enters #119
Terminal of the monitor unit, releasing earthing of
#684 Terminal of the monitor unit.
• As a result, a circuit in which electricity flows from
Terminal C of Parking Brake Relay 2 to Terminal A
of Parking Brake Relay 2 (self-exciting circuit) is
formed, and the parking brake solenoid valve
works, releasing the parking brake.
• As the parking brake switch automatically returns
to neutral, the circuit from Terminal E of the
parking brake switch to Parking Brake Relay 2 is
blocked.
T2-4-30
SYSTEM/Electric System
PHOTO
Cab
Key Switch
005
From #163Terminal
of Fuse Box A
Fuse Box A
From #6 terminal 264
of Fuse Box B 362
684 692 157
Monitor Unit 210
119
124
135 123
From Terminal L
of Alternator 55 54
(W hen forming a self-exciting circuit) 163
693 79
108
12 99
Parking Brake
ON 144
Switch
133
スイッチ Parking Brake Parking Brake
NEUTRAL 121 120
Relay 2 Relay 1 696
OFF 695 694
698
699
AB E F GH A B CD E A B CD E
700 697
684 Battery
Monitor Unit Fuse Relay Battery
(100A)
119
Parking Brake
Solenoid Valve
To #638 Terminal
of Fuse Box B From Terminal L
of Alternator T4GB-02-03-016
T2-4-31
SYSTEM/Electric System
EMERGENCY STEERING CHECK CIRCUIT
(OPTIONAL)
T2-4-32
SYSTEM/Electric System
PHOTO
Emergency Steering
081 Key Switch
Fuse Box A
264
362
692 157
210
124
135 123
464
55 54
163
80 79
108
12
120
695 694
Emergency
Steering 698
Emergency
Steering Relay 699
Check Switch 700 697
Fuse Box B
348 838
149
577 148
327
Emergency 222
Steering 323 126
Pump Delivery 6
Pressure Sensor 11
119 9 638
35
179
Emergency 158
180 Steering 710
Pump Unit
381
Monitor 711 75
Unit
Battery Relay
Fuse
(100A)
Battery
Alternator
T4GB-02-03-020
T2-4-33
SYSTEM/Electric System
(Blank)
T2-4-34
SECTION 3
COMPONENT OPERATION
CONTENTS
Group 1 Pump Device Group 5 Steering Valve
Outline ...................................................... T3-1-1 Outline ...................................................... T3-5-1
Main Pump ............................................... T3-1-2 Operation .................................................. T3-5-4
Regulator.................................................. T3-1-4 Steering Overload Relief Valve ................. T3-5-8
Priority Valve .......................................... T3-1-18
Group 6 Pilot Valve
Pilot Pump,Pump Delivery
Outline (Two Lever Type Pilot Valve for
Pressure Switch .................................. T3-1-19
Front Attachment) ................................... T3-6-1
Steering Main Relief Valve...................... T3-1-20
Operation .................................................. T3-6-2
Group 2 Control Valve Electromagnetic Detent............................. T3-6-6
Outline ...................................................... T3-2-1 Outline (Joystick Type Pilot Valve for
Hydraulic Circuit ..................................... T3-2-14 Front Attachment) ................................... T3-6-7
Main Relief Valve.................................... T3-2-22 Operation .................................................. T3-6-8
Overload Relief Valve ............................. T3-2-26 Electromagnetic Detent........................... T3-6-12
Restriction Valve..................................... T3-2-31 Outline (Lever Type Pilot Valve for
Negative Control Valve ........................... T3-2-32 Additional Circuit) (Optional) ................. T3-6-13
Flow Rate Control Valve ......................... T3-2-34 Operation ................................................ T3-6-14
Outline (Joystick Type Pilot Valve for
Group 3 Hydraulic Fan Motor
Additional Circuit) (Optional) ................... T3-6-17
Outline ...................................................... T3-3-1
Operation ................................................ T3-6-18
Operation ................................................. T3-3-4
Flow Control Valve.................................... T3-3-6
Reverse Control Valve .............................. T3-3-8
Fun Pump ............................................... T3-3-10
4GBT-3-1
Group 7 Charging Block Group 11 Brake Valve
Outline .....................................................T3-7-1 Outline ................................................... T3-11-1
Priority Valve ............................................T3-7-6 Operation ............................................... T3-11-4
Pilot Relief Valve ......................................T3-7-7
Pump Torque Control Proportional Group 12 Others
Solenoid Valve .......................................T3-7-8 Pilot Shutoff Valve ..................................T3-12-1
Service Brake Accumulator, Propeller Shaft .......................................T3-12-2
Pilot Accumulator ...................................T3-7-9 Emergency Steering Check Block ...........T3-12-3
Parking Brake Solenoid Valve ................T3-7-10 Emergency Steering Pump (Optional) .....T3-12-4
Service Brake Pressure Sensor..............T3-7-12
Parking Brake Pressure Sensor .............T3-7-12
Group 10 Axle
Outline ...................................................T3-10-1
Differential..............................................T3-10-2
Torque Proportioning Differential (TPD) ..T3-10-6
Limited Slip Differential (LSD) ................T3-10-8
Service Brake....................................... T3-10-10
Final Drivel Axle Shaft .......................... T3-10-12
4GCT-3-2
COMPONENT OPERATION / Pump Device
OUTLINE
Pump device has a main pump (1) and a pilot pump (2), Main pump (1) is a swash-plate type variable dis-
and main pump (1) has a built-in priority valve (6). placement axial plunger pump.
Driving force of the engine is transmitted to the shaft Pilot pump (2) is a gear pump.
(3) through the transmission input shaft, and actuates Pump delivery pressure switch (4) is provided for con-
main pump (1) and pilot pump (2). trolling the main pump.
1
PHOTO
2
Hydraulic System
114
4 T4GB-03-01-001C
T3-1-1
COMPONENT OPERATION / Pump Device
MAIN PUMP
Main pump supplies pressure oil for operating the cyl- When cylinder block (1) rotates, plungers (2) recipro-
inders and other hydraulic components. Also, the pump cate inside the cylinder block because of the tilting of
is provided with a regulator for controlling the delivery swash plate (4), and delivers the hydraulic oil.
flow. Control of the main pump delivery is made by changing
Shaft (5) is connected with the cylinder block (1), and the tilting angle of swash plate (4) with servo piston 1
shaft (5) and cylinder block (1) corotate. (3) and servo piston 2 (6) which increase or decrease
the stroke of plungers (2).
1 2 3 4
8
7
T4GB-03-01-002C
T3-1-2
COMPONENT OPERATION / Pump Device
Increase and Decrease Operations of Delivery
Flow
Tilting angle variation of swash plate (4) is made by 7
the movement of servo piston 1 (3) and servo piston
2 (6). 8
6
Movement of the servo pistons is controlled by the
3
regulator. Also, the feed back of the swash plate
movement is given to the regulator by feed back lever
(7) and link (8).
4
T4GB-03-01-024
Boss Housing
C B
T3-1-3
COMPONENT OPERATION / Pump Device
REGULATOR
Regulator controls flow of the main pump, receiving
various kinds of signal pressure. 3 2 1 4
The regulator includes the spring (1), sleeve 1 (2), Air
Pi1 T Vent
sleeve 2 (7), spool 1 (3), spool 2 (6), piston (4), load
piston (5), inner spring (8), and outer spring (9).
Regulator opens and closes the circuit leading to servo
piston 1 (10) by receiving various kinds of signal Pi2
pressure, and controls delivery flow of the pump by
Pg
varying the tilting angle of swash plate (11).
ST
NOTE: Pilot primary pressure (Pg) is always ap- T
plied to Servo Piston 2 (12). Pd1
T
5 7 6 8、9
10 12
Large Small
Tilting Angle
T4GB-03-01-006C
T3-1-4
COMPONENT OPERATION / Pump Device
2 3 4 1
5 6 7 8 9
10 11
T4GB-03-01-007C
12
T3-1-5
COMPONENT OPERATION / Pump Device
Control Function of Regulator
Regulator has the following three control functions.
0 Pressure (P)
T3-1-6
COMPONENT OPERATION / Pump Device
(Blank)
T3-1-7
COMPONENT OPERATION / Pump Device
Control by Pump Control Pressure
Flow Decrease
1. When the control lever stroke is reduced, pres- Flow (Q)
sure difference arising before and after the flow
control valve (difference between pressure Pi1
and Pi2) in the control valve is enlarged.
2. Pump Control Pressure Pi1 pushes Spool 1 (3),
and Spool 1 (3) moves toward the arrow.
3. This movement causes Pilot Primary Pressure Pg
to be led to servo piston 1 (10) also.
4. As there are two servo piston 1’s (10), the swash
plate (11) tilts toward the flow decreasing direc- 0 Pump Control Pressure (Pi1-Pi2)
tion.
5. Movement of swash plate (11) is conveyed to
sleeve 1 (2) through feed back lever link (13).
Sleeve 1 (2) moves toward the movement of
3 2 1 4
spool 1 (3). Air
6. Pilot pressure having been led to servo piston 1 Pi1 T Vent
(10) is blocked when sleeve 1 (2) has moved the
same distance as spool 1 (3). This causes servo
piston 1’s (10) to stop and the flow decrease is Pi2
completed.
Pg
ST
T
Pd1
T
13
10 12
Large Small
Tilting Angle
T4GB-03-01-006C
T3-1-8
COMPONENT OPERATION / Pump Device
Pump Pilot
Control Pres- To Hydraulic Primary 3 2 4 1
sure Pi1 Oil Tank Pressure Pg Pump
Control Pressure
Pi2
Pump Torque
Control Pressure
ST
Self Delivery 13
12
Pressure Pd1
10 11
T4GB-03-01-008
Pump Pilot
Control Pres- To Hydraulic Primary
Oil Tank Pressure Pg 3 2 4 1
sure Pi1 Pump
Control Pressure
Pi2
Pump Torque
Control Pressure
ST
Self Delivery 13
Pressure Pd1 12
10
11
T4GB-03-01-009
T3-1-9
COMPONENT OPERATION / Pump Device
Flow Increase
1. When the control lever stroke is enlarged, pres-
sure difference arising before and after the flow
control valve (difference between pressure Pi1 Flow (Q)
and Pi2) in the control valve is reduced.
2. Spool 1 (3) moves back by spring force (1).
3. This movement causes the circuit of servo piston
1’s (10) to be led to the hydraulic oil tank.
4. As Pilot Primary Presuure Pg is always applied to
servo piston 2 (12), the swash plate (11) tilts to-
ward the flow increasing direction.
5. Movement of the swash plate (11) is transmitted
to sleeve 1 (2) through the feed back lever link 0 Pump Control Pressure (Pi1-Pi2)
(13). Sleeve 1 (2) moves toward the movement of
spool 1 (3).
6. When sleeve 1 (2) has moved the same distance
as spool 1 (3) did, communication of servo piston
3 2 1 4
1’s (10) with the hydraulic tank is stopped, and Air
this causes servo piston 1’s (10) to stop and the Pi1 T Vent
flow increase is completed.
Pi2
Pg
ST
T
Pd1
T
13
10 12
Large Small
Tilting Angle
T4GB-03-01-006C
T3-1-10
COMPONENT OPERATION / Pump Device
Pump Pilot
Control Pressure To Hydraulic Primary 3 2 4 1
Pi1 Oil Tank Pressure Pg Pump
Control Pressure
Pi2
Pump Torque
Control Pressure
ST
T4GB-03-01-010
Pump Pilot
Control Pres- To Hydraulic Primary
3 2 4 1
sure Pi1 Oil Tank Pressure Pg Pump
Control Pressure
Pi2
Pump Torque
Control Pressure
ST
13
Self Delivery
Pressure Pd1 12
10
11
T4GB-03-01-011
T3-1-11
COMPONENT OPERATION / Pump Device
Control by Pump Delivery Pressure
(Self Delivery Pressure)
Flow Decrease
1. When load is applied to the pump by making one
operation or another, Pump Delivery Pressure Flow (Q)
Pd1 rises. (As done during an operation, the
pump control pressure (Pi1 - Pi2) remains low-
ered.)
2. Load piston (5) pushes spool 2 (6), the inner
spring (8), and the outer spring (9), and Spool 2
(6) moves toward the arrow.
3. This movement causes Pilot Primary Pressure Pg
to be led to servo piston 1’s (10) also.
4. As there are two servo piston 1 (10), the swash 0 Pressure (P)
plate (11) tilts toward the flow decreasing direc-
tion.
5. This movement of the swash plate (11) is con-
veyed to sleeve 2 (7) through the feed back lever
Air
link (13). Sleeve 2 (7) moves toward the move- Pi1 T Vent
ment of spool 2 (6).
6. Pilot pressure having been led to servo piston 1
(10) is blocked when sleeve 2 (7) has moved the
same distance as spool 2 (6). This causes servo Pi2
piston 1’s (10) to stop and the flow decrease is
Pg
completed.
ST
T
Pd1
T
5 7 6 8、9
10 12 13
Large Small
Tilting Angle
T4GB-03-01-006C
T3-1-12
COMPONENT OPERATION / Pump Device
Pump Pilot
Control Pressure To Hydraulic Primary 6 7
5 Pi1 Oil Tank Pressure Pg Pump
Control Pressure
Pi2
Pump Torque
Control Pressure
ST
8 9
T4GB-03-01-012
Pump Pilot
Control To Hydraulic Primary 6 7
5 Pressure Pi1 Oil Tank Pressure Pg Pump
Control Pressure
Pi2
Pump Torque
Control Pressure
ST
8 9
T4GB-03-01-013
T3-1-13
COMPONENT OPERATION / Pump Device
Flow Increase
1. When the pump load is reduced, Self Delivery
Pressure Pd1 lowers. (As done during an opera-
tion, the pump control pressure (Pi1 - Pi2) re- Flow (Q)
mains lowered.)
2. Load piston (5) and spool 2 (6) are pushed by
inner spring (8) and outer spring (9), and spool 2
(6) moves toward the arrow.
3. This movement causes the circuit of servo piston
1’s (10) to be led to the hydraulic oil tank.
4. As Pilot Primary Presuure Pg is always applied to
servo piston 2 (12), swash plate (11) tilts toward
the flow increasing direction. 0 Pressure (P)
5. Movement of swash plate (11) is conveyed to
sleeve 2 (7) through feed back lever link (13).
sleeve 2 (7) moves toward the movement of spool Air
2 (6). Pi1 T Vent
6. When sleeve 2 (7) has moved the same distance
as spool 2 (6), the openings of spool 2 (6) and
sleeve 2 (7) close, stopping communication of Pi2
servo piston 1’s (10) with the hydraulic tank, and
this causes servo piston 1’s (10) to stop and the Pg
flow increase is completed.
ST
T
Pd1
T
5 7 6 8、9
10 Large 12 13
Small
Tilting Angle
T4GB-03-01-006C
T3-1-14
COMPONENT OPERATION / Pump Device
Pump Pilot
Control To Hydraulic Primary 6 7
5 Pressure Pi1 Oil Tank Pressure Pg Pump
Control Pressure
Pi2
Pump Torque
Control Pressure
ST
8 9
T4GB-03-01-014
Pump Pilot
Control Pres- To Hydraulic Primary
6 7
sure Pi1 Oil Tank Pressure Pg Pump
5
Control Pressure
Pi2
Pump Torque
Control Pressure
ST
T4GB-03-01-015
T3-1-15
COMPONENT OPERATION / Pump Device
Control of Torque Control Solenoid Valve by Pilot
Pressure
Flow Decrease
1. Command from the MC (main controller) drives
the pump torque control solenoid valve, and Flow (Q)
Pump Torque Control Pressure ST enters the
regulator.
2. Adding to Self Delivery Pressure Pd1, Pump
Torque Control Pressure ST works on load piston
(5).
3. Load piston (5) pushes spool 2 (6), inner spring
(8), and outer spring (9), and spool 2 (6) moves
toward the arrow.
4. This movement causes Pilot Primary Pressure Pg 0 Pressure (P)
to be led to servo piston 1’s (10) also.
5. As there are two servo piston 1 (10), swash plate
(11) tilts toward the flow decreasing direction.
6. This movement of swash plate (11) is conveyed to
Air
sleeve 2 (7) through feed back lever link (13). Pi1 T Vent
sleeve 2 (7) moves toward the movement of spool
2 (6).
7. Pilot pressure having been led to servo piston 1
(10) is blocked when sleeve 2 (7) has moved the Pi2
same distance as spool 2 (6). This causes servo
Pg
piston 1’s (10) to stop and the flow decrease is
completed. ST
T
Pd1
T
5 7 6 8、9
10 12 13
Large Small
Tilting Angle
T4GB-03-01-006C
T3-1-16
COMPONENT OPERATION / Pump Device
Pump Pilot
Control To Hydraulic Primary
5 6 7
Pressure Pi1 Oil Tank Pressure Pg Pump
Control Pressure
Pi2
Pump Torque
Control Pressure
ST
8 9
T4GB-03-01-016
Pump Pilot
Control Pressure To Hydraulic Primary 6 7
5 Pi1 Oil Tank Pressure Pg Pump
Control Pressure
Pi2
Pump Torque
Control Pressure
ST
8 9
T4GB-03-01-017
T3-1-17
COMPONENT OPERATION / Pump Device
PRIORITY VALVE PHOTO
(Refer to the Main Curcuit in the SYSTEM /
Hydraulic System) Hydraulic System
114
Main pump has a built-in priority valve. Before Steering Operation
Priority valve is installed for effectively distributing the
main pump delivery oil to the steering valve and the
control valve.
Operation Port
CF
1. Before Steering Operation
Pressure oil from the main pump tends to flow to To Steering Valve
the steering valve through Port CF, but flows to
the both ends of the priority valve spool because From Main Pump
Port CF is blocked.
Pressure oil on one end of the spool flows from
To Control Valve
Port LS to the hydraulic oil tank through the Port
steering valve, and its pressure is lowered. The EF Spool
spool to both ends of which different pressures
are applied moves toward Port LS, overcoming
the the spring force. Therefore, the majority of the
main pump pressure oil flows to the control valve
through Port EF. Spring
2. In Steering Operation
If steering is operated, and the steering valve
spool moves, pressure at Port LS rise in response
Port LS
to the amount of the steering valve spool move-
ment. The spool is pushed up by the pressure at To Hydraulic T4GB-03-01-018C
Oil Tank
Port LS and the spring force. Therefore, the main
pump pressure oil flows to both Port EF and Port In Steering Operation
CF. When the steering valve spool moves to the
maximum stroke, the majority of the main pump
pressure oil flows to the steering valve through
Port CF.
Port
CF
To Steering Valve
To Control Valve
Spool
Port
EF
Spring
Port LS T4GB-03-01-019C
T3-1-18
COMPONENT OPERATION / Pump Device
PILOT PUMP
Drive gear (1) is driven throught the shaft of the main
1
pump, and the diven gear (2) geared to this also ro- Suction Port
tates. 2
PHOTO
Hydraulic System
114 Delivery Port
T137-02-03-005C
T157-02-03-010C
6 - Earth 8 - Electric Source (5V) 6 7 8 9
7 - Output 9 - Pressure-applied Part
(Diaphragm)
T3-1-19
COMPONENT OPERATION / Pump Device
STEERING MAIN RELIEF VALVE ILLUSTRATION
T4GB-01-02-009
Main pump has a built-in steering main relief valve. Before Operation
When the steering circuit pressure exceed the set
pressure, pressure oil is returned to the hydarulic oil Steering Circuit Pressure for
tank through inside of the main pump housing. up to Set Pressure
Operation
In case steering circuit pressure exceed the set
pressure, the puppet is pushed toward the spring,
and pressure is returned to the hydraulic oil tank
through inside of the main pump housing.
T4GB-03-01-020C
In Operation
Steering Circuit Pressure for
less than Set Pressure
To Main Pump
Housing
T4GB-03-01-021C
T3-1-20
COMPONENT OPERATION / Control Valve
OUTLINE
Control valve controls pressure, flow, and direction of
oil in the hydraulic circuit.
The control valve includes the main relief valve, over-
load relief valves, pump control valve, restriction valves,
flow control valve, and spools, and its operation is of
the hydraulic pilot type. PHOTO
Lift Arm
Lift Arm
Bucket Bucket
T4GB-03-02-001C
T4GB-03-02-002C
T3-2-1
COMPONENT OPERATION / Control Valve
Component Layout
ZW220
1 2
11
5
10 9 8 T4GB-03-02-003C
T3-2-2
COMPONENT OPERATION / Control Valve
ZW220
A 5
7 6 9 8 7
E
4
2
3
T4GB-03-02-004C
1 - Bucket Flow Control Valve 4 - Overload Relief Valve 7 - Restriction Valve 10 - Load Check Valve
(Bucket: Rod End) (Arm Lift Circuit)
2 - Pump Control Valve 5 - Overload Relief Valve 8 - Low-pressure Relief Valve 11 - Load Check Valve
(Lift Arm: Bottom End) (Bucket Circuit)
3 - Overload Relief Valve 6 - Make-up Valve 9 - Main Relief Valve
(Bucket: Bottom End) (Lift Arm: Rod End)
T3-2-3
COMPONENT OPERATION / Control Valve
ZW220
1 2
11
5
7 7
10 9 8 T4GB-03-02-003C
T3-2-4
COMPONENT OPERATION / Control Valve
ZW220
8
9
*
Section A
7
7
2 T4GB-03-02-005C
Section B*
8
9
T4GB-03-02-006C
1 - Bucket Flow Control Valve 4 - Overload Relief Valve 7- Restriction Valve 10 - Load Check Valve
(Bucket: Rod End) (Arm Lift Circuit)
2 - Pump Control Valve 5 - Overload Relief Valve 8- Low-pressure Relief Valve 11 - Load Check Valve
(Lift Arm: Bottom End) (Bucket Circuit)
3 - Overload Relief Valve 6 - Make-up Valve 9- Main Relief Valve
(Bucket: Bottom End) (Lift Arm: Rod End)
* Refer to T3-2-3.
T3-2-5
COMPONENT OPERATION / Control Valve
ZW220
1 2
11
5
10 9 8 T4GB-03-02-003C
T3-2-6
COMPONENT OPERATION / Control Valve
ZW220
Section C* 6 10
7 7
*
Section D
4 11 1
*
Section E
T4GB-03-02-007C
1 - Bucket Flow Control Valve 4 - Overload Relief Valve 7- Restriction Valve 10 - Load Check Valve
(Bucket: Rod End) (Arm Lift Circuit)
2 - Pump Control Valve 5 - Overload Relief Valve 8- Low-pressure Relief Valve 11 - Load Check Valve
(Lift Arm: Bottom End) (Bucket Circuit)
3 - Overload Relief Valve 6 - Make-up Valve 9- Main Relief Valve
(Bucket: Bottom End) (Lift Arm: Rod End)
* Refer to T3-2-3.
T3-2-7
COMPONENT OPERATION / Control Valve
ZW250
1 2 3
6
8
11 10
T4GB-03-02-008C
T3-2-8
COMPONENT OPERATION / Control Valve
ZW250
D
10
C
6 8
8 7
A
E 4
5
T4GB-03-02-009C
1 - Flow Control Valve 4 - Overload Relief Valve 7 - Make-up Valve 10 - Main Relief Valve
(Poppet) (Bucket: Bottom End) (Lift Arm: for Rod)
2 - Flow Control Valve 5 - Overload Relief Valve 8 - Restriction Valve 11 - Load Check Valve
(Changeover Valve) (Bucket: Rod End) (Lift Arm Circuit)
3 - Pump Control Valve 6 - Overload Relief Valve 9 - Low-pressure Relief Valve
(Lift Arm: Bottom End)
T3-2-9
COMPONENT OPERATION / Control Valve
ZW250
1 2 3
8
7
11 10
T4GB-03-02-008C
T3-2-10
COMPONENT OPERATION / Control Valve
ZW250
Section A*
11
7 6
8 8
1 2
Section B*
5
4
T4GB-03-02-010C
1 - Flow Control Valve 4- Overload Relief Valve 7- Make-up Valve 10 - Main Relief Valve
(Poppet) (Bucket: Bottom End) (Lift Arm: for Rod)
2 - Flow Control Valve 5 - Overload Relief Valve 8 - Restriction Valve 11 - Load Check Valve
(Changeover Valve) (Bucket: Rod End) (Lift Arm Circuit)
3 - Pump Control Valve 6 - Overload Relief Valve 9- Low-pressure Relief Valve
(Lift Arm: Bottom End)
* Refer to T3-2-9.
T3-2-11
COMPONENT OPERATION / Control Valve
ZW250
1 2 3
6
8
11 10
T4GB-03-02-008C
T3-2-12
COMPONENT OPERATION / Control Valve
ZW250
Section C:*
10
9
Section D*
*
Section E
3
T4GB-03-02-011C
1 - Flow Control Valve 4- Overload Relief Valve 7- Make-up Valve 10 - Main Relief Valve
(Poppet) (Bucket: Bottom End) (Lift Arm: for Rod)
2 - Flow Control Valve 5 - Overload Relief Valve 8 - Restriction Valve 11 - Load Check Valve
(Changeover Valve) (Bucket: Rod End) (Lift Arm Circuit)
3 - Pump Control Valve 6 - Overload Relief Valve 9- Low-pressure Relief Valve
(Lift Arm: Bottom End)
* Refer to T3-2-9.
T3-2-13
COMPONENT OPERATION / Control Valve
HYDRAULIC CIRCUIT
ZW220
Main Circuit
Main circuit contains a parallel circuit, which enables
compound operations.
T3-2-14
COMPONENT OPERATION / Control Valve
Control Valve
Bucket
Overload
Relief Valve
Lift Arm
Main Pump
T4GB-03-02-012C
T3-2-15
COMPONENT OPERATION / Control Valve
ZW250
Main Circuit
Main circuit contains a parallel circuit, which enables
compound operations.
T3-2-16
COMPONENT OPERATION / Control Valve
Bucket Cylinder
Lift Arm
Cylinder
Control Valve
Bucket Overload
Valve
Lift Arm
Parallel Circuit
Main Pump
T4GB-03-02-023C
T3-2-17
COMPONENT OPERATION / Control Valve
Pilot Operation Circuit
ZW220
Pressure oil from the pilot valve (shown in numerals)
works on the spools of the control valve, and moves
the spools.
• Pressure oil is being sent to the bucket spool for
dumping and crowding operations.
• Pressure oil is being sent to the lift arm spool for
raising and lowering operations.
Spool for lowering is two-staged, and the first
stage is for lowering the lift arm, while the second
stage is for floating the lift arm.
T3-2-18
COMPONENT OPERATION / Control Valve
PHOTO
Bucket Lift Arm
Pilot Valve Pilot Valve Pilot Valve
018
1 2 3 4
Pilot Pump
Control Valve
Bucket
1
2
Lift Arm
4
3
Main Pump
T4GB-03-02-013
T3-2-19
COMPONENT OPERATION / Control Valve
ZW250
Pressure oil from the pilot valve (shown in numerals)
works on the spools of the control valve, and moves
the spools.
• Pressure oil is being sent to the bucket spool for
dumping and crowding operations.
• Pressure oil is being sent to the lift arm spool for
raising and lowering operations.
Spool for lowering is two-staged, and the first
stage is for lowering the lift arm, while the second
stage is for floating the lift arm.
T3-2-20
COMPONENT OPERATION / Control Valve
PHOTO
Pilot Valve
1 2 3 4
Pilot Pump 018
Control Valve
PHOTO
Bucket
2
1
Lift Arm
3
Main Pump
T4GB-03-02-024
1 - Bucket Crowding 3 - Lift Arm Lowering
2 - Bucket Dumping 4 - Lift Arm Raising
T3-2-21
COMPONENT OPERATION / Control Valve
MAIN RELIEF VALVE
Main relief valve prevents pressure inside the main
circuit from increasing over the set pressure during
operation of the cylinder.
This prevents oil leakage from the hoses and piping
fittings as well as cylinder breakage.
ZW220
Operation of Relief Valve
1. Pressure at port HP (in the main circuit) works on
the pilot poppet through orifice A of the main
poppet and orifice B of the seat.
2. When the pressure at Port HP rises to the setting
force of spring B, the pilot poppet opens, and
pressure oil flows to port LP (in the hydraulic oil
tank) passing through passage A and the periph-
ery of the sleeve.
3. At this time, pressure difference arises between
port HP and the spring chamber, caused by orifice
A.
4. When this pressure difference reaches the value
corresponding to the set force of spring A, the
main poppet opens, and the pressure oil at port
HP flows to port LP.
5. As a result, pressure in the main circuit lowers.
6. If the main circuit pressure lowers to the set
pressure, the main poppet is closed by the force
of spring A.
T3-2-22
COMPONENT OPERATION / Control Valve
In Normal Condition:
HP
LP T4GB-03-02-034C
Sleeve Spring Cham- Spring A Pilot Poppet
ber
When Relieving:
HP
LP T4GB-03-02-035C
Sleeve Spring Spring A Pilot Poppet
Chamber
T3-2-23
COMPONENT OPERATION / Control Valve
ZW250
Operation of Relief Valve
1. Pressure at port HP (in the main circuit) works on
the pilot poppet through orifice A of the main
poppet and orifice B of the seat.
2. When the pressure at port HP rises to the setting
force of spring B, the pilot poppet opens, and
pressure oil flows to port LP (in the hydraulic oil
tank) passing through passage A and the periph-
ery of the sleeve.
3. At this time, pressure difference arises between
port HP and the spring chamber, caused by orifice
A.
4. When this pressure difference reaches the value
corresponding to the set force of spring A, the
main poppet opens, and the pressure oil at port
HP flows to port LP.
5. As a result, pressure in the the main circuit lowers.
6. If the main circuit pressure lowers to the set
pressure, the main poppet is closed by the force
of spring A.
T3-2-24
COMPONENT OPERATION / Control Valve
In Normal Condition:
HP
LP T4GB-03-02-025C
Sleeve Spring Spring A Pilot Poppet
Chamber
When Relieving:
HP
LP
Sleeve Spring Spring A Pilot Poppet
Chamber T4GB-03-02-026C
T3-2-25
COMPONENT OPERATION / Control Valve
T3-2-26
COMPONENT OPERATION / Control Valve
In Normal Condition:
Main Poppet Sleeve Spring A Passage A Spring B
HP
T4GB-03-02-030C
LP
Orifice Piston Spring Chamber Pilot Poppet Spring C
When Relieving:
Main Poppet Sleeve Spring A Passage A Spring B
HP
LP T4GB-03-02-031C
In Make-up Operation:
Sleeve
HP
LP R4GB-03-02-032
Spring C
T3-2-27
COMPONENT OPERATION / Control Valve
Operation of Relief Valve in ZW220 (Ports on
Bottom End of Lift Arm and Bucket)
1. Pressure at port HP (front circuit) passes the seat,
and works on the shaft.
2. When the pressure at port HP rises to the value
corresponding to the set force of spring A, the
shaft moves, and pressure oil flows to port LP.
3. As a result, the pressure in the front circuit lowers.
4. If the pressure in the front circuit lowers to the set
pressure, the shaft is moved by the force of spring
A, and the oil passage closes.
Make-up Operation
1. When the pressure at port HP (in the front circuit)
lowers than the pressure at port LP (in the hy-
draulic oil tank), the sleeve moves right.
2. Hydraulic oil at port LP flows into port HP, and
cavitation is prevented.
3. When the pressure at port HP rises to the set
pressure, the sleeve is closed by the force of
spring C.
T3-2-28
COMPONENT OPERATION / Control Valve
In Normal Condition:
Seat HP Shaft
LP
Spring A Spring B
T4GB-03-02-027C
LP
Spring A Spring B
T4GB-03-02-028C
LP
Spring A Spring B
T4GB-03-02-029C
T3-2-29
COMPONENT OPERATION / Control Valve
(Blank)
T3-2-30
COMPONENT OPERATION / Control Valve
RESTRICTION VALVE
PHOTO
Restriction valve is installed at the inlet part to the pilot Check Valve Orifice
Main Control Valve
circuit on the both ends of the spool for the lift arm
cylinders. 089
If the pilot valve is made at the neutral position during
operation of the lift arm, the pilot pressure oil having
been supplied to the spool for the lift arm is drained Pilot
through the orifice of the check valve of the restriction Spool End
Valve End
valve, and pilot pressure gradually lowers.
As a result, shock to the body occurring in operation of
the front attachment can be reduced by gradually re-
turning the lift arm spool to the neutral position.
T4GB-03-02-014C
Orifice Size
Raise Side 1.0 mm
Lower Side 1.2 mm
T3-2-31
COMPONENT OPERATION / Control Valve
PUMP CONTROL VALVE
Control valve has a built-in negative control valve. Pump
Orifice Control Valve
Pump control valve controls the main pump delivery
flow of the main pump by the flow control pressure (Pi1
and Pi2). Pi2
Operation
Pi1
• At Neutral
Pressure oil coming through the control valve
neutral circuit at neutral position of the control
valve is supplied as pilot pressure for controlling
the pump delivery flow from before and after the
orifice of the pump control valve installed at the
outlet of the control valve.
At this time, spool B moves left because differen-
tial pressure is occurring between the Pi1 and Pi2.
Therefore, pilot pressure (PS2) enters the
large-diameter chamber for the servo piston
through spool B and spool A. Pilot pressure (PS2)
also enters the small-diameter chamber for the
servo piston, but as the the large-diameter
chamber has a larger area than the
small-diameter chamber, the servo piston moves
Main Pump
right, and the pump delivery flow is reduced.
• In Operation Neutral
Servo Piston
In operations handling the lift arm and the bucket, Circuit Large-Diameter
Small-Diameter
pressure oil is not supplied to Pi1 and Pi2. Chamber Chamber
At this time, differential pressure is lowered be- Spool A
tween the Pi1 and Pi2, so the regulator for the
Pilot Pressure
main pump is at neutral, and restriction of delivery (PS2)
flow is not made (increase pump delivery flow).
Oil Flow
L/min
A
ZW220 ZW250
Pump Control Pressure Pump Control Pressure
Flow Flow
(Pi1-Pi2) (Pi1-Pi2)
2 L/min 2 L/min
MPa (kgf/cm ) MPa (kgf/cm )
+0.01 +0.1 +0.01 +0.1
A 0.39 -0(4 -0) 271±3 0.49 -0(5 -0) 291±3
B 1.47±0.05(15±0.5) 80±2 1.47±0.05(15±0.5) 100±2
+0.01 +0.1 +0.01 +0.1
B C 0.67 -0(17 -0) 36±3 0.67 -0(17 -0) 55±3
T3-2-32
COMPONENT OPERATION / Control Valve
ZW220 ZW250
Pi2 Pi1
E
Orifice Part
Section E *1 Section E *3
Pi1
Pi1
Orifice Part
Pi2
Pi2
Negative Control
Valve
T4GB-03-02-017C
Negative Control
Valve
T4GB-03-02-016C
T3-2-33
COMPONENT OPERATION / Control Valve
FLOW CONTROL VALVE In Compound Operation of Bucket Crowding and
Lift Arm Raising
Flow control valve is installed in the bucket circuit, and
1. Part of the pressure oil from the main pump is
narrows the circuit in compound operations, giving
supplied to the lift arm cylinders through the lift
priority to operations of the other actuators.
arm spool.
2. Remainder of the pressure oil from the main
ZW220
pump is supplied to the bucket spool through the
In Single Operation of Bucket Crowding
parallel circuit.
1. Pressure oil from the main pump passes the lift 3. At that time, flow is restricted because pressure
arm spool. oil passes the orifice through check valve 2.
2. Pressure oil from the lift arm spool flows to the 4. Pressure oil having passed the orifice flows to the
bucket spool through check valve 1, and is sup- bucket spool, and is supplied to the bucket cylin-
plied to the bucket cylinder. der.
5. As a result, flow to the bucket spool is restricted,
and more pressure oil is supplied to the lift arm
cylinder ends having higher pressure, and both
the bucket and the arm move.
Check Valve 2
Orifice
Check
Valve 1
T3-2-34
COMPONENT OPERATION / Control Valve
ZW220 Bucket
In Single Operation of Bucket Crowding Cylinder
Bucket Spool
Pilot Pressure
Lift Arm
Check Cylinders
Valve 1
T4GB-03-02-019
Bucket
Cylinder
Bucket Spool
Pilot Pressure Lift Arm
Cylinders
Check
Valve 2
Orifice
Parallel Circuit
T4GB-03-02-019
T3-2-35
COMPONENT OPERATION / Control Valve
ZW250 In Compound Operation of Bucket Crowding and
In Single Operation of Bucket Crowding Lift Arm Raising
1. Pressure oil from the main pump flows toward the 1. Part of the pressure oil from the main pump is
poppet. supplied to the lift arm cylinder through the lift arm
2. Pressure oil entering the poppet pushes the spool.
poppet left, and flows to the bucket spool, with its 2. Remainder of the pressure oil from the main
small portion also flowing to the bucket spool pump is supplied toward the bucket spool.
through the check valve inside the poppet to be 3. Pressure oil from the main pump passes the par-
supplied to the bucket cylinder. allel circuit, and flows to the changeover valve
through the check valve of the poppet.
4. At this time, the changeover valve is positioned
on the orifice end because pilot pressure for
raising the lift arm is working on the changeover
valve.
5. By the effect of the orifice of the changeover valve,
pressure on the spring end of the poppet rises,
and force to push the poppet right (for closing)
arises.
6. As a result, flow to the bucket spool is restricted,
and more pressure oil is supplied to the lift arm
end having higher pressure, and both the bucket
cylinder and the arm cylinder move.
Spring B
To Bucket Spool
Pilot Presser
for Lift Arm Raising
Changeover Valve Pressure Oil
from Main Pump
To Bucket Spool
T1V1-03-03-064C
T3-2-36
COMPONENT OPERATION / Control Valve
ZW250 Bucket
In Single Operation of Bucket Crowding Cylinder
Spring A
Bucket Spool
Poppet
Pilot Pressure
Spring B
Check
Valve
Main Pump
T4GB-03-02-021
Spring A
Poppet
Bucket Spool
Pilot Pressure
Pilot Pressure
Changeover Lift Arm Cylinders
Valve
Spring B
Lift Arm
Check Spool Pilot Pressure
Valve
Parallel Circuit
Main Pump
T4GB-03-02-022
T3-2-37
COMPONENT OPERATION / Control Valve
(Blank)
T3-2-38
COMPONENT OPERATION / Hydraulic Fan Motor
OUTLINE
Shaft of the fan motor is provided with the cooling fan,
and the pressure oil from the fan pump rotates the
cooling fan by driving the shaft.
Fan motor has a built-in reverse control solenoid valve,
a flow adjustment solenoid valve and others, and the
reverse control solenoid valve controls the motor
rotational direction, and the flow adjustment solenoid PHOTO
valve controls rotation speed.
Cooling Fan Motor
039 040
Reverse Control
Solenoid Valve
Flow Adjustment
Solenoid Valve
C
A
B B
C
A
T4GB-03-03-001C
T3-3-1
COMPONENT OPERATION / Hydraulic Fan Motor
Component Layout
Cooling Fan
Shaft
Fan Motor
Reverse Spool
Reverse Control
Flow Control Valve Solenoid Valve
Reverse Signal
Flow Control Valve from MC
Spring
Relief Valve
Flow Adjustment
Solenoid Valve
Flow Adjustment
Command Signal
from MC
(For example)
ZW220
-1
Speed (min ) Coolant (°C) Hydraulic Oil (°C) T/C Oil (°C) A/C ON (°C) Current (mA)
500 50 50 50 - 800
500 80 70 80 - 800
1650 90 90 100 30 - 35 0
1650 100 100 110 - 0
T3-3-2
COMPONENT OPERATION / Hydraulic Fan Motor
*
Section B-B
*
Section C-C
5 6
7 8 9
10
*
Section A-A
1 2 3 4
12 11
T4GB-03-03-002C
*Refer to T3-3-1
T3-3-3
COMPONENT OPERATION / Hydraulic Fan Motor
OPERATION
Fan motor is a swash-plate type axial piston motor,
and converts the pressure oil sent from the fan motor
into rotational motion.
T3-3-4
COMPONENT OPERATION / Hydraulic Fan Motor
α°
F1
F3
F2
2 4 3 T4GB-03-03-003C
To Tank
T4GB-03-03-004C
T3-3-5
COMPONENT OPERATION / Hydraulic Fan Motor
FLOW CONTROL VALVE
In case the cooling water and oil are below the set
temperature, the flow control valve supplies necessary
amount of the pressure oil from the fan pump, and
returns redundant amount to the tank to make control
for lowering the engine load and wind noise of the
cooling fan.
Operation
1. Pressure oil flowing from port P works on the A
end as upstream pressure of flow control valve
orifice (8), and on the B end as its downstream
pressure, and the differential pressure works on
flow control valve spring (12).
2. When the pressure difference becomes larger
than the set force, flow control valve spool (8)
moves, and redundant flow flows to port T.
T3-3-6
COMPONENT OPERATION / Hydraulic Fan Motor
7 8
12
T
T4GB-03-03-005C
To Tank
T3-3-7
COMPONENT OPERATION / Hydraulic Fan Motor
REVERSE CONTROL VALVE
Fan motor is reversed by operations of the reverse
control solenoid valve and the reverse spool.
Operation
• At Neutral of Reverse Control Solenoid Valve
1. When reverse control solenoid valve (1) is at
neutral, the pressure oil (P) from the fan pump is
blocked by changeover valve (2).
2. As reverse spool (11) is being pushed by spring
(4), the pressure oil (P) from the fan pump flows
to port MB, and the fan motor rotates normally.
T3-3-8
COMPONENT OPERATION / Hydraulic Fan Motor
At Neutral
P
OFF
MA MB
T
3 T4GB-03-03-006C
In Operation
P
ON
MA MB
T 3
T4GB-03-03-007C
T3-3-9
COMPONENT OPERATION / Hydraulic Fan Motor
FAN PUMP
Fan pump is a gear pump always supplying pressure
oil to the fan motor during the engine operation.
Fan pump is installed to the engine.
PHOTO
T4GB-03-03-008C
6 7 8 9 10
T3-3-10
COMPONENT OPERATION / Steering Pilot Valve
OUTLINE
Steering pilot valve is located between the brake/pilot
pump and the steering valve.
Steering pilot valve supplies the pressure oil from the
pilot pump to the steering valve in response to the
movement of the steering wheel. (Refer to the Steering PHOTO
Curcuit in the SYSTEM / Hydraulic System)
Steering System
076
Steering
Wheel
T487-03-02-001C
Port T Port P
(to Hydraulic Oil Tank) (from Brake/Pilot Pump)
T3-4-1
COMPONENT OPERATION / Steering Pilot Valve
CONSTRUCTION
11 7 8 10
Steering pilot valve consists of gerotor (8), drive (7),
sleeve (3), spool (4), pin (5), housing (1), centering
springs (2) and others.
T1F3-03-07-002C
1 2 5 4 3 6
4
2
3
1 Port R
Port L
Hole
Port P
10
9
6
T4GB-03-04-008
T3-4-2
COMPONENT OPERATION / Steering Pilot Valve
OPERATION
4 1 3 7
Sleeve (3), spool (4) and drive (7) are mutually
connected by pin (5). When the steering wheel (or the Port L Port R
spool (4)) is turned, a relative angular difference arises
between sleeve (3) and spool (4) because the hole of
spool (4) is a lengthened one.
Movement of the steering wheel is conveyed only to
spool (4), and port P (from the steering pump) is
connected to port R (to the steering valve) or port L
through sleeve (3) and spool (4). Steering
Wheel
Port T Port P
2 11 2
T4GB-03-04-007C
11 1 6 10
T1F3-03-07-002C
1 5 4 3 7 8
T3-4-3
COMPONENT OPERATION / Steering Pilot Valve
Steering Left:
1. When the steering wheel is turned left, spool (4) 4. Return oil from the steering valve enters port R,
rotates, and the pressure oil from the brake/pilot and flows in the order of housing (1) - sleeve (3) -
pump flows in the order of port P - sleeve (3) - spool (4) - sleeve (3) - port T to return to the
spool (4) - sleeve (3) - housing (1) - gerotor (8). hydraulic oil tank.
2. Pressure oil from gerotor (8) flows in the order of 5. When the pressure oil from the brake/pilot pump
housing (1) - sleeve (3) - spool (4) - sleeve (3) - enters gerotor (8), gerotor (8) rotates leftwards.
port L - steering valve, and controls the steering Rotation of gerotor (8) is transmitted to the sleeve
valve. (3) through drive (7), and sleeve (3) rotates
3. Steering valve drives the steering cylinders with leftwards similarly.
the pressure oil from the main pump, and directs 6. When sleeve (3) rotates the same amount of turns
the vehicle body toward left. as spool (4), passages of sleeve (3) and spool (4)
are closed, and operation of the steering valve is
stopped.
7. Therefore, gerotor (8) rotates in response to
rotation of the steering wheel, and the steering
valve is operated in response to the amount of
turns of the steering wheel.
Steering Cylinder
PHOTO
Steering System
078
Steering Valve
Main Pump
Port L
Port R
Port P Brake/Pilot
Pump
Port T
1
4 2 3
T3-4-4
COMPONENT OPERATION / Steering Pilot Valve
Steering Right T L R P
T4GB-03-04-010C
Neutral T P
T4GB-03-04-011C
T3-4-5
COMPONENT OPERATION / Steering Pilot Valve
(Blank)
T3-4-6
COMPONENT OPERATION / Steering Valve
OUTLINE
Steering valve is located between the main pump and
the steering cylinder.
Steering valve supplies the pressure oil from the main
pump to the steering cylinder in response to the pilot oil
pressure of the steering pilot valve.
Steering cylinder is provided with the overload relief
valve.
PHOTO
Steering System
078
T4GB-03-04-001C
T3-5-1
COMPONENT OPERATION / Steering Valve
Component Layout
4 1 2 3
Port A Port T
Port B
Port Pa Port Pb
5 6 Port P 4 5
Port DR
Port LS T4GB-03-04-002C
Port A: Pressure for Steering Port B: Pressure for Steering Port Pa: Pilot Pressure for Port Pb: Pilot Pressure for
Right Left Steering Right Steering Left
Port P: From Main Pump Port T: Return to Hydraulic Oil Port LS: To Port LS of Priority Port DR: Return to Hydraulic Oil
Tank Valve Tank
T3-5-2
COMPONENT OPERATION / Steering Valve
*
Section A
7 Port P Port DR 1
Port T
*
Section B
3
Port LS
Port B Port A
Port Pb Port Pa
T4GB-03-04-003C
4 7 5 4
*
Section C 6
T4GB-03-04-006C
*: Refer to T3-5-1
T3-5-3
COMPONENT OPERATION / Steering Valve
OPERATION
In Neutral
1. When steering spool (1) is in the neutral position,
port A and port B of the steering cylinder are
closed.
2. Pressure oil from the main pump does not flow to
the steering cylinders because port P is closed.
T3-5-4
COMPONENT OPERATION / Steering Valve
*
Section A
Port P Port DR
Port T
:*
Section B
Port B Port A
T4GB-03-04-004C
*: Refer to T3-5-1.
T3-5-5
COMPONENT OPERATION / Steering Valve
When Steering Left
1. When the steering wheel is turned left, the pilot
pressure oil is sent to port Pb from the steering
pilot valve, and spool (1) moves right.
2. Pressure oil from the main pump is sent to the
steering valve through port P, and further sent to
passage A (7) through variable orifice (5).
3. Pressure oil in passage A (7) pushes and opens
load check valve (4), and flows to the steering
cylinders through port B.
4. And the return oil from the steering cylinders
enters spool (1) through port A, and returns to the
hydraulic oil tank through port T.
5. Also, the pilot pressure oil flowing into port Pb
pushes spool (1) on port Pb end, while flowing to
port Pa after being decompressed by fixed orifice
(6). This reduces the shock caused by fast
operation of the steering wheel. (Refer to T3-5-2
and also Steering Curcuit in the SYSTEM /
Hydraulic System)
T3-5-6
COMPONENT OPERATION / Steering Valve
Port P
7 Port T 5
Port B Port LS
Port A
Port Pb Port Pa
6 7 5
T4GB-03-04-005
T3-5-7
COMPONENT OPERATION / Steering Valve
STEERING OVERLOAD RELIEF VALVE
Steering overload relief valves are installed in the left Make-up Operation
and right steering circuits. Overload relief valve
1. When the pressure at port HP (in the steering
controls pressure in the respective steering circuits
cylinder circuit) lowers than the pressure at port
from rising abnormally high when the steering cylinders
LP (in the hydraulic oil tank), the sleeve moves
are moved by an external force.
right.
2. Hydraulic oil flows into port HP, and cavitation is
Operation of Relief Valve
prevented.
1. Pressure at port HP (in the steering circuit) works 3. If the pressure at port HP rises to the set pressure
on the pilot poppet, passing the orifice in the value, the sleeve is closed by the force of spring
piston. C.
2. When the pressure at port HP rises to the setting
force of spring B, the pilot poppet opens, and
pressure oil flows to port LP (in the hydraulic oil
tank), passing passage A and the periphery of the
sleeve.
3. At this moment, pressure difference arises
between port HP and the spring chamber caused
by the orifice.
4. When this pressure difference reaches the value
corresponding to the set force of spring A, the
piston and the main poppet open, and the
pressure oil at port HP flows to port LP.
5. As a result, the pressure in the steering cylinder
circuit lowers.
6. If the steering cylinder circuit pressure lowers to
the set pressure value, the piston and the main
poppet are closed by the force of spring A.
T3-5-8
COMPONENT OPERATION / Steering Valve
Normally (When not Relieving):
Main
Poppet Sleeve Spring A Passage A Spring B
HP
T4GB-03-02-030C
LP
Orifice Piston Spring Chamber Pilot Spring C
Poppet
When Relieving:
Main Sleeve Spring A Passage A Spring B
Poppet
HP
LP T4GB-03-02-031C
In Make-up Operation:
Sleeve
HP
LP T4GB-03-02-032C
Spring C
T3-5-9
COMPONENT OPERATION / Steering Valve
(Blank)
T3-5-10
COMPONENT OPERATION / Pilot Valve
OUTLINE (TWO LEVER TYPE PILOT
VALVE FOR FRONT ATTACHMENT)
Pilot valve is a valve for controlling the pilot pressure
oil for moving the spool of the control valve. Provided
with the PPC (Pressure Proportional Control Valve)
function, the pilot valve outputs pressure
corresponding to the control lever stroke of the control PHOTO
lever, and moves the spool of the control valve.
The bi-directional, four-port type is adopted for the Control Levers
front-end attachment. 012
Port No.
1 Bucket Crowd
2 Bucket Tilting Out
3 Lift Arm Lower
4 Lift Arm Raise
Hydraulic Symbol
1 2 3 4 T
T4GB-03-05-001C
P T
1 2
T4GB-03-05-002C
3 4
T3-6-1
COMPONENT OPERATION / Pilot Valve
OPERATION
E F
At Neutral (between A and B of Pusher Stroke) Pilot
Pressure
1. At the neutral position of the control lever, spool
(7) is completely blocking the pressure oil of port D
P. Also, the outlet port is connected to port T
through the notch part of spool (7), and the
pressure oil at the output port is equal to the
pressure in the hydraulic tank. C
2. When the control lever is moved slightly, lever (1)
is tilted, and push rod (2) and pusher (3) are
A B Pusher Stroke
pushed in. Pusher (3) and spring guide (4) remain
mutually connected, and move downward, T505-02-07-006
compressing return spring (6). Output Diagram
3. At this time, spool (7) is pushed by balance spring
(5), and moves downward until the clearance in
Part A becomes zero.
4. During this movement, the output port remains
connected with port T, and pressure oil is not
supplied to the output port.
T3-6-2
COMPONENT OPERATION / Pilot Valve
Pusher Stroke: between A and B
Port T
(Clearance of
(A) Part A: 0)
Notch Part
Port P
T4GB-03-05-004C
Output Port
T4GB-03-05-003C
T3-6-3
COMPONENT OPERATION / Pilot Valve
During Metering or Pressure Decrease (In Pusher Full Stroke (Pusher Stroke between E and F)
Stroke between C and D)
1. When the control lever is fully stroked, pusher (3)
1. When the control lever is further tilted, the ouput moves downward until spring guide (4) contacts
port is connected with port P through spool (7). the shoulder part of the casing.
2. Pressure oil from Port P flows into the output port 2. At this time, spool (7) is directly pushed by the
through spool (7), and the pressure at the output bottom of pusher (3). Therefore, the output port
port is raised. remains connected with port P through the notch
3. Pressure at the output port works on face B of part of spool (7) because even if the pressure at
spool (7), and tends to push up spool (7). the output port is raised, spool (7) does not move
4. In case the force tending to push up the spool (7) upward.
is smaller than the spring force of balance spring 3. As a result, the pressure on the output port end is
(5), balance spring (5) is not compressed. equal to the pressure at port P.
Therefore, port P and the output port remain Stroke amount C of the pusher determines the
connected, and the pressure at the output port total stroke of the lever.
keeps rising.
5. When the pressure at the output port rises further,
E F
the force tending to push spool (7) up increases. If Pilot
this force becomes larger than the force of Pressure
balance spring (5), spool (7) moves upwards,
D
compressing the balance spring (5).
6. When spool (7) moves upward, the output port is
not connected any longer, and pressure oil stops
flowing from port P to the output port.
C
And pressure increase at the output port is
stopped.
7. In this way, balance spring (5) is compressed by A B Pusher Stroke
the amount spool (7) is pushed down, and the
pressure at the output port is the balanced T505-02-07-006
Output Diagram
pressure working on the spring force and spool
(7).
T3-6-4
COMPONENT OPERATION / Pilot Valve
Pusher Stroke: between C and D Pusher Stroke: between E and F
5 (C)
Port T
4
Notch Part
Face B
Port P Port P
7
7
T3-6-5
COMPONENT OPERATION / Pilot Valve
Electromagnetic Detent
Coil for detent is installed at the push rod part of the
pilot valve.
1. When one of the control levers is tilted, push rod 3. Adsorbed condition is retained until the coil
(2) and plate (8) of the other are pushed upwards assembly is unexcited or until adsorption is
by the spring force. forcefully cancelled by moving the control lever
2. If the control lever is operated until its stroke end, the other way around.
plate (8) of the other is adsorbed by coil assembly
(10).
10
T4GB-03-05-007C
T3-6-6
COMPONENT OPERATION / Pilot Valve
OUTLINE (JOYSTICK TYPE PILOT VALVE
FOR FRONT ATTACHMENT)
Port No.
1 Bucket Crowd
2 Bucket Tilting Out
3 Lift Arm Lower
4 Lift Arm Raise
Hydraulic Symbol
PHOTO
Control Lever
011 018
P
1 2 T
3 4
T4GB-03-05-001C
2
3
4 1
P T4GB-03-05-008C
T3-6-7
COMPONENT OPERATION / Pilot Valve
OPERATION
At Neutral
1. At neutral, spool (7) completely blocks the
pressure oil at port P. Also, the output port is
connected with port T through the fine control
hole of spool (7).
For this reason, the pressure at the output port is
equal to the pressure at port T.
2. If the control lever is tilted slightly, disc (1) is tilted,
and push rod (2) and piston (3) are pushed in.
Piston (3) pushes down spring guide (4) and
balance spring (5), and moves downward.
3. At this time, spool (7) is pushed by spring (5), and
moves downward until the clearance at part A
becomes zero.
4. During this movement, the output port remains
connected with port T, and pressure oil is not
supplied to the output port.
T3-6-8
COMPONENT OPERATION / Pilot Valve
At Neutral
5
6
Port T
(A) (Clearance of Part A: 0)
Port P
Fine Control Hole
7
Output Port
T4GB-03-05-009C
T4GB-03-05-010C
T3-6-9
COMPONENT OPERATION / Pilot Valve
During Metering or Pressure Decrease Full Stroke
1. When the control lever is further tilted, the ouput 1. When the control lever is fully stroked, disc (7)
port is connected with port P through the fine pushes down push rod (2) and piston (3), and
control hole of spool (7). spring guide (4) pushes down spool (7).
2. Pressure oil from port P flows into the output port 2. Output port is connected with port P through the
through spool (7), and the pressure at the output fine control hole of spool (7).
port is raised. 3. Spool (7) is being pushed down by spring guide
3. Pressure at the output port works on spool (7), (4), and the output port remains connected
and tends to push up spool (7). through the fine control hole of spool (7) because
4. In case the force tending to push up spool (7) is even if the pressure at the output port is raised,
smaller than the spring force of balance spring (5), spool (7) does not move upward.
balance spring (5) is not compressed. Therefore, 4. As a result, the pressure on the output port end is
port P and the output port remain connected, and equal to the pressure at Port P.
the pressure at the output port keeps rising.
5. When the pressure at the output port rises further,
the force tending to push spool (7) up increases. If
this force becomes larger than the force of
balance spring (5), spool (7) moves upwards,
compressing the balance spring (5).
6. When spool (7) moves upward, the output port is
not connected any longer, and pressure oil stops
flowing from port P to the output port.
And pressure increase at the output port is
stopped.
7. In this way, balance spring (5) is compressed by
the amount spool (7) is pushed down, and the
pressure at the output port is the balanced
pressure working on the spring force and spool
(7).
T3-6-10
COMPONENT OPERATION / Pilot Valve
During Metering or Pressure Decrease Full Stroke
3
4
5
7
7
T3-6-11
COMPONENT OPERATION / Pilot Valve
ELECTROMAGNETIC DETENT
Coils for detents are installed at the push rod part of
the pilot valve.
1. When one of the control levers is tilted, push rod 3. Adsorption condition is retained until coil
(2) and plate (9) of the other are pushed upwards assembly (8) is unexcited or until adsorption is
by the spring force. forcefully cancelled by operating the control lever
2. If the control lever is operated until its stroke end, toward the other direction.
plate (9) of the other is adsorbed by coil assembly
(8).
T4GB-03-05-013C
T3-6-12
COMPONENT OPERATION / Pilot Valve
OUTLINE (LEVER TYPE PILOT VALVE
FOR ADDITIONAL CIRCUIT) (OPTIONAL)
Port No.
1 Optional
2 Optional
T
Hydraulic Symbol
P
P T P
1 2
1 2
T554-02-07-009C
T1LA-03-04-001C
1 2
T3-6-13
COMPONENT OPERATION / Pilot Valve
OPERATION
At Neutral (between A and B of Pusher Stroke)
1. At the neutral position of the control lever, spool 5. When the pressure at the output port rises further,
(7) is completely blocking the pressure oil of port the force tending to push spool (7) up increases. If
P. Also, the outlet port is connected to port T this force becomes larger than the force of
through the notch part of spool (7), and the balance spring (5), spool (7) moves upwards,
pressure oil at the output port is equal to the compressing balance spring (5).
pressure in the hydraulic tank. 6. When spool (7) moves upward, the notch part
2. When the control lever is moved slightly, cam (1) closes, and pressure oil stops flowing from port P
is tilted, and pusher (2) and spring guide (4) are to the output port. And pressure increase at the
pushed in. Pusher (3) and spring guide (4) move output port is stopped.
downward, remaining mutually connected, and 7. In this way, balance spring (5) is compressed by
compressing return spring (6). the amount the spool (7) is pushed down, and the
3. At this time, spool (7) is pushed by balance spring pressure at the output port is the balanced
(5), and moves downward until the clearance in pressure working on the spring force and spool
Part A becomes zero. (7).
4. During this movement, the output port remains
connected with port T, and pressure oil is not
supplied to the output port.
T3-6-14
COMPONENT OPERATION / Pilot Valve
Between A and B of Pusher Stroke
3
4
Port T
6
(A)
Clearance at
Port P Part A: 0
Hole Part
7
Passage
T1LA-03-04-002C
T1LA-03-04-003C
Output Port
Port T
Port P
Hole Part
7
T3-6-15
COMPONENT OPERATION / Pilot Valve
(Blank)
T3-6-16
COMPONENT OPERATION / Pilot Valve
OUTLINE (JOYSTICK TYPE PILOT VALVE
FOR ADDITIONAL CIRCUIT) (OPTIONAL)
Port No.
1 Optional
2 Optional
3 Optional
4 Optional
Hydraulic P T
Symbol
1 3 2 4 4
T105-02-07-020C 3
T1V1-03-04-001C
T3-6-17
COMPONENT OPERATION / Pilot Valve
OPERATION
Head of spool (6) is hung by the top face of spring
guide (3). Spring guide (3) is lifted up by return spring
(5).
T3-6-18
COMPONENT OPERATION / Pilot Valve
1 1
2 2
6
3 3 Port T
4 4
7
5 5 Port P
6 Output Port
6
Port T Port T
7 Port P 7 Port P
T3-6-19
COMPONENT OPERATION/Pilot Valve
During Metering or Pressure Decrease (Output
Diagram: between C and D)
E F
1. When the control lever is further tilted and pusher Pilot
(2) is pushed down, hole part (7) of spool (6) Pressure
reaches port P, and the prsessure oil from port P D
flows into the output port.
2. Pressure at the output port works on the bottom of
spool (6), and tends to push up spool (6).
3. In case the force working on spool (6) is smaller C
than the spring force of balance spring (4),
balance spring (5) is not compressed. Therefore,
A B
spool (6) is not pushed up, and the pressure at Lever Stroke
the output port keeps rising. T523-02-05-001
4. When the pressure at the output port rises further,
the force tending to push spool (6) up increases. If Output Diagram
this force becomes larger than the force of the
balance spring (4), spool (6) moves upwards,
compressing the balance spring (4).
5. When spool (6) moves upward, hole part (7)
closes, pressure oil stops flowing from Port P to
the output port, and pressure increase at the
output port is stopped.
6. In this way, the balance spring (4) is compressed
by the amount spool (6) is pushed down, and the
pressure at the output port is the balanced
pressure working on the spring force and spool
(6).
T3-6-20
COMPONENT OPERATION/Pilot Valve
1 1
2 2
3 3
4 4
5 5
6 6
Port T Port T
7 Port P 7 Port P
T3-6-21
COMPONENT OPERATION/Pilot Valve
Full Stroke (Output Diagram: between E and F)
1. When the control lever is fully stroked, pusher (2)
moves downward until it contacts the shoulder Pilot E F
part of the casing. Pressure
2. At this time, spool (6) is directly pushed by the D
bottom of the pusher (2). Therefore, even if the
pressure at the output port is raised, hole part (7)
of spool (6) is not closed.
3. As a result, the pressure on the output port end is C
equal to the pressure at port P.
A B
Lever Stroke
NOTE: Stroke amount E of the pusher (2)
determines the total stroke of the lever. T523-02-05-001
Output Diagram
T3-6-22
COMPONENT OPERATION/Pilot Valve
5
E
Port T
7
Port P
T3-6-23
COMPONENT OPERATION/Pilot Valve
(Blank)
T3-6-24
COMPONENT OPERATION / Charging Block
OUTLINE
Charging block is installed for supplying the pressure
oil from the pilot pump not only to the service brake
accumulator and the brake valve by giving them priority,
but also to the parking brake, the steering pilot valve,
and others.
Charging block consists of the priority valve, relief
valve, pump torque control proportional solenoid valve,
pilot relief valve, check valve, and others. PHOTO
Charging Block
To Steering
072 073
Pilot Valve
Relief Valve
Pilot Relief (14.7 MPa)
Valve
(3.9 MPa)
To Steering
Pilot Valve
Check
Valve
Parking Brake
Solenoid Valve to
be adopted in EU
To Ride
specification
Control Valve
Port for Attaching
Pilot Accumulator
T4GB-03-06-001C
T3-7-1
COMPONENT OPERATION / Charging Block
Component Layout
1 2 3 4 5 6
Relief Valve 22 8
14.7 MPa)
9
10 Pilot Relief Valve
(3.9 MPa)
11
21
12
13
14
20
15
16
17
18
T4GB-03-06-002C
4 19
T3-7-2
COMPONENT OPERATION / Charging Block
11
Section V-V*
10
14
*
Section U-U
12
21
15 16
*
Section T-T
20
19
*
Section S-S
18
T4GB-03-06-003C
4
*Refer to T3-7-1.
T3-7-3
COMPONENT OPERATION / Charging Block
Component Layout
1 2 3 4 5 6
22 8
9
10
11
21
12
13
14
20
15
16
17
18
T4GB-03-06-002C
4 19
T3-7-4
COMPONENT OPERATION / Charging Block
Section Z-Z*
6
7
Section Y-Y*
8
Section X-X*
*
Section W-W
22
9 T4GB-03-06-004C
*Refer to T3-7-1.
T3-7-5
COMPONENT OPERATION / Charging Block
PRIORITY VALVE (REFER TO THE PILOT
CIRCUIT IN THE SYSTEM / HYDRAULIC
SYSTEM)
1. Pressure oil from the pilot pump flows in through Below Set Pressure of Service Brake Accumulator
port P, and works on the both ends of the plunger
of the priority valve.
2. Same pressure is applied to the both ends of the Relief Valve
plunger, so the plunger does not move, and a
restricted amount of pressure oil is supplied to the
other pilot circuits.
3. When the service brake accumulator is
accumulated exceeding the set pressure, the
piston of the relief valve pushes the needle valve.
4. Pressure oil in the spring chamber of the plunger
flows to the hydraulic oil tank through port DR.
5. Plunger is pushed toward the spring chamber to
stroke because the spring chamber is From Port P
decompressed.
6. A larger amount of the pressure oil from the pilot
pump is supplied to the other pilot circuits through Plunger
the priority valve.
(Section W-W)
T4GB-03-06-005C
Service Brake
To Port Dr Accumulator
Pressure
From Port P
Plunger
Spring Chamber
(Section W-W)
T4GB-03-06-006C
T3-7-6
COMPONENT OPERATION / Charging Block
PILOT RELIEF VALVE
1. Pilot relief valve prevents the pressure in the pilot
circuit from increasing over the set pressure Normally
during operations of the actuators like the pilot Poppet
valve.
2. When the pilot circuit pressure is above the set
pressure, pressure oil works on the poppet of the
pilot relief valve.
3. Poppet works toward the spring to be connected
with port DR.
4. Pressure oil in the pilot circuit returns to the
hydraulic oil tank through port DR.
5. When the pilot circuit pressure is below the set
pressure to the spring force, the poppet moves
left, closing connection of port DR.
(Section V-V)
From Port P T4GB-03-06-007C
When Relieving
Poppet Port DR
(Section V-V)
T4GB-03-06-008C
Spring
T3-7-7
COMPONENT OPERATION / Charging Block
PUMP TORQUE CONTROL PROPORTI-
ONAL SOLENOID VALVE (REFER TO THE
PILOT CIRCUIT IN THE SYSTEM /
HYDRAULIC SYSTEM)
Pilot pressure supplied to the main pump regulator Not in Operation of Solenoid Valve
for controlling the pump delivery flow is controlled by
the operation of the pump torque control proportional To Main Pump
solenoid valve. Regulator
Port X
1. When there is no signal from the MC (Main
Controller), the spool of the solenoid valve is
being pushed by the spring.
2. Pilot pressure oil is supplied to port ST of the main
pump regulator through port X.
3. When signal is transmitted from the MC, the spool
moves toward the spring in response to the signal
of the spool, and the amount of the pilot pressure
oil flowing out of Port X is lowered.
4. When the signal from the MC becomes the
maximum value, the spool fully strokes toward the
Spring
spring, and the pilot pressure oil is blocked by the
spool.
5. Port X and port DR2 are connected, and the pilot
pressure oil at port X is lost.
(Section U-U) Pilot Pressure Oil
T4GB-03-06-009C
Port X
Port
DR2
Spool Spring
(Section U-U)
Pilot Pressure Oil
T4GB-03-06-010C
T3-7-8
COMPONENT OPERATION / Charging Block
SERVICE BRAKE ACCUMULATOR /
PILOT ACCUMULATOR
Accumulator is installed in the pilot circuit leading to IMPORTANT: Construction of the accumulator
the service brake and the pilot valve. does not allow disassembly.
High-pressure nitrogen gas is contained in the Replace the whole assembly, when
accumulator, and the pilot pressure oil compresses the necessary.
nitrogen gas through the diaphragm.
Circuit pressure oil is retained by compression of the
nitrogen gas.
PHOTO
Charging Block
073
Seal Ring
Retainer
Shell
Diaphragm
Valve Poppet
T4GB-03-06-011C
T3-7-9
COMPONENT OPERATION / Charging Block
PARKING BRAKE SOLENOID VALVE
Pressure oil from the pilot pump is accumulated in the When the parking brake solenoid valve is operated,
pilot accumulator, and its pressure always works on the pilot accumulator enters the parking brake through
the outlet of the parking brake solenoid valve. the spool, and releases the parking brake.
Parking Brake
Solenoid Valve
Port for Attaching
Pilot Accumulator T4GB-03-07-004C
T3-7-10
COMPONENT OPERATION / Charging Block
Not in Operation
Parking Brake
Pressure Sensor Parking Brake
Drain Port
Spool
Spring
Parking Brake
Solenoid Valve
(Section T-T)
Pilot Accumulator
Pressure T4GB-03-07-005C
In Operation
Parking Brake
Pressure Sensor Parking Brake
Spool
Spring
Parking Brake
Solenoid Valve (Section T-T) Pilot Pressure
Accumulator
T4GB-03-07-006C
Pressure
T3-7-11
COMPONENT OPERATION / Charging Block
SERVICE BRAKE PRESSURE SENSOR
Brake pressure necessary for the service brake is
sensed. Sensor is installed in the service brake circuit
of the charging block, and senses the oil pressure of
the service brake accumulator.
T176-03-01-023C
T3-7-12
COMPONENT OPERATION / Ride Control Valve
OUTLINE
(Refer to the SYSTEM / Control System)
Ride control valve enables stable traveling by
absorbing the force generated in the lift arm cylinders
in traveling.
Ride control valve consists of the ride control solenoid
valve, spool, charge-cut spool, overload relief valve
and others.
PHOTO
099
Overload A
Relief Valve
Ride Control
Solenoid Valve
T4GB-03-08-001C
T3-8-1
COMPONENT OPERATION / Ride Control Valve
Component Layout
Lift Arm
Cylinder
Ride Control
Accumulator
2.9 MPa
Ride Control Valve
5
SP
3
39.2 MPa Pi
1
2
11.3 MPa
To Hydraulic Oil Tank
From Charging
Block
T4GB-03-08-002C
T3-8-2
COMPONENT OPERATION / Ride Control Valve
*
Section A
To Ride Control
Port Pi Accumulator
1 Port SP 3
Port B
Port A
Port T
T4GB-03-08-003C
2 4
*Refer to T3-8-1.
T3-8-3
COMPONENT OPERATION / Ride Control Valve
OPERATION
1. At neutral, port Pi and the ouput port are not 4. When the main spool is pushed toward spring 2,
connected, blocked by the spool. port A (on the bottom ends of the lift arm cylinder)
2. When the signal from the MC (Main Controller) and the ride control accumulator are connected,
enters the solenoid, the solenoid is excited. and port B (on the rod end of the lift arm cylinder)
3. Solenoid pushes the spool with the force and port T are connected.
corresponding to the signal from the MC, so port 5. As a result, the accumulator absorbs the pushing
Pi and the output port are connected, and pilot force of the lift arm cylinders, and the load
pressure oil pushes the main spool. generated by the pushing up force is absorbed by
sucking up the hydraulic oil from the tank port.
Section A*
To Ride Control
Pilot Pressure Accumulator
Spool Port Pi
Port A Port B
Spring 1
Output Port
Spring 2
T4GB-03-08-006C
Tank Port
Main Spool
*Refer to T3-8-1.
T3-8-4
COMPONENT OPERATION / Ride Control Valve
(Blank)
T3-8-5
COMPONENT OPERATION / Ride Control Valve
CHARGE-CUT SPOOL
Charge-cut spool accumulates the pressure oil in the
lift arm cylinders in the ride control accumulator, and
shuts down the pressure oil from the lift arm cylinders
when the ride control accumulator is accumulated to
the set pressure.
T3-8-6
COMPONENT OPERATION / Ride Control Valve
T4GB-03-08-008C
Sectional Area M Sectional Area N
T3-8-7
COMPONENT OPERATION / Ride Control Valve
OVERLOAD RELIEF VALVE
Overload relief valve is installed for preventing hoses
and the ride control accumulator from being damaged
in case the pressure in the bottom end circuit of the lift
arm cylinders is suddenly raised by an external force
or something during operation of the lift arm cylinders.
Operation
1. Pressure at port HP (in the main circuit) works on
the pilot poppet, passing orifice A of the main
poppet and orifice B of the seat.
2. When the pressure at port HP rises to the setting
force of spring B, the pilot poppet opens, and
pressure oil flows to port LP, passing passage A
and the periphery of the sleeve.
3. At this moment, pressure difference arises
between port HP and the spring chamber caused
by orifice A.
4. When this pressure difference reaches the value
corresponding to the set force of spring A, the
main poppet opens, and the pressure oil at port
HP flows to port LP.
5. As a result, the pressure in the actuator circuit
lowers.
6. If the actuator circuit pressure lowers to the set
pressure, the main poppet is closed by the force
of spring A.
T3-8-8
COMPONENT OPERATION / Ride Control Valve
Normally:
Sleeve Make-up Valve Main Poppet Orifice A Orifice B Seat Passage A Spring B
HP
LP T176-03-03-012C
When Relieving:
HP
LP T176-03-03-013C
T3-8-9
COMPONENT OPERATION / Ride Control Valve
RIDE CONTROL ACCUMULATOR
Ride control accumulator is installed in the IMPORTANT: Construction of the ride control
accumulation circuit of the ride control. accumulator does not allow
High-pressure nitrogen gas is contained in the disassembly. Replace the whole
accumulator, and the pressure oil compresses the assembly, when necessary.
nitrogen gas through the piston.
Compression of the nitrogen gas dampens shock of
the pressure oil due to pitching and the like of the lift
arm cylinder raising circuit.
T4GB-03-08-009C
T3-8-10
COMPONENT OPERATION / Ride Control Valve
DRAIN PLUG
Ride control valve is provided with the drain plug for
returning the pressure oil of the ride control
accumulator to the oil tank at the time of maintenance
or something.
When necessary, connect the accumulator port (port
SP) and the tank port (port T) by loosening the lock nut
first and the drain plug later.
Section B*
Port SP
Lock Nut
Drain Plug
Relief Plug
Port T T4GB-03-08-010C
*Refer to T3-8-1.
T3-8-11
COMPONENT OPERATION / Ride Control Valve
(Blank)
T3-8-12
&20321(1723(5$7,21'ULYH8QLW
287/,1(
'ULYH XQLW FRQVLVWV RIWKHWUDQVPLVVLRQ DQG WKH WRUTXH
FRQYHUWHU
'ULYHXQLWLVFRQQHFWHGZLWKWKHHQJLQH3RZHUIURPWKH PHOTO
HQJLQH LV WUDQVPLWWHG WR WKH WUDQVPLVVLRQ WKURXJK WKH
HQJLQHIO\ZKHHODQGWKHWRUTXHFRQYHUWHU ZF Transmission
108 109 110
7RUTXH&RQYHUWHU
7*&&
7UDQVPLVVLRQ
7
&20321(1723(5$7,21'ULYH8QLW
72548(&219(57(5
7RUTXH FRQYHUWHU FRQVLVWV RI WKH FRQYHUWHU ZKHHO DV
VHPEO\ SXPS GULYH GHYLFH WXUELQH VKDIW DQG RWKHUV
,QWKH FRQYHUWHU ZKHHO DVVHPEO\ LPSHOOHU DQG WXU
ELQH DUHPXWXDOO\ RSSRVHG ZLWK VWDWRU LQVWDOOHG
LQ EHWZHHQ DQG WKH\ DUH DOO FRQWDLQHG LQ WKH FDVLQJ
ILOOHGZLWKRLO
(QJLQHURWDWLRQLVWUDQVPLWWHGIURPWKHHQJLQHZKHHOWR
WKH WUDQVPLVVLRQ WKURXJK LQSXW SODWH FRYHU ZKHHO
LPSHOOHUWXUELQHDQGWXUELQHVKDIW
+\GUDXOLFRLOIRUWKHWRUTXHFRQYHUWHUVXSSOLHGIURPWKH
WUDQVPLVVLRQ FRQWURO YDOYH HQWHUV WKH FRQYHUWHU ZKHHO
WKURXJKWKHRLOSDVVDJHRIWKHVWDWRUVXSSRUW
:KHQLPSHOOHULVURWDWHGE\WKHHQJLQHURWDWLRQRLO
IORZV DORQJ WKH EODGH RI LPSHOOHU WRZDUG WKH SH
ULSKHU\DQGIORZVLQWRWKHWXUELQH7KLVRLOIORZFRO
OLGHV ZLWK WKH EODGH RI WXUELQH DQG URWDWHV WXUELQH
DQG WXUELQH VKDIW $OVR WKH RXWSXW WRUTXH RI
WXUELQH VKDIW LV JHQHUDWHG E\ WKH UHDFWLRQ IRUFH
FDXVHGE\WKHRLOIORZGLUHFWLRQFKDQJHGXHWRFROOLVLRQ
RIRLOZLWKWKHEODGHRIWXUELQH
6WDWRU DOZD\V UHFWLILHV WKH RLO IORZ FRPLQJ RXW RI
WXUELQHLQWKHGHWHUPLQHGGLUHFWLRQDQGIORZVWKHRLO
LQWRLPSHOOHUIRUHQODUJLQJWRUTXH
7
&20321(1723(5$7,21'ULYH8QLW
7*&&
&RYHU:KHHO 6WDWRU ,PSHOOHU *XLGH&DUULHU
,QSXW3ODWH ,QSXW*XLGH ,PSHOOHU+XE 7XUELQH6KDIW
7XUELQH 6WDWRU+XE 3XPS'ULYH*HDU
7
&20321(1723(5$7,21'ULYH8QLW
75$160,66,21
7UDQVPLVVLRQ VR IXFWLRQV DV WR WUDQVIRUP WKH URWDWLRQ
VSHHG DQG URWDWLRQ GLUHFWLRQ RI WKH SRZHU WUDQVPLWWHG
IURPWKHWRUTXHFRQYHUWHU
7UDQVPLVVLRQLVFRPSRVHGRIWKHIRXUFOXWFKVKDIWDV PHOTO
VHPEOLHVWKHUHYHUVHJHDURXWSXWVKDIWSDUNLQJEUDNH
FRQWUROYDOYHDQGRWKHUV TCM Transmission
6DIHW\YDOYHLVLQVWDOOHGDWWKHLQOHWSDUWRIWKHK\GUDXOLF
108
RLOIRUWKHWRUTXHFRQYHUWHUDQGUHOLHYHVUHGXQGDQWRLO
LQWRWKHFRQYHUWHUKRXVLQJ
5HYHUVH
,QSXW
*HDU
)RUZDUG
&OXWFK 5HYHUVH
&OXWFK
,GOHU*HDU
2XWSXW
7*&
7UDQVPLVVLRQ*HDU/D\RXW'UDZLQJ
9LHZHGIURP9HKLFOH)URQW(QG㧕
7
&20321(1723(5$7,21'ULYH8QLW
)URQW9LHZRI7UDQVPLVVLRQ
$
%
%
&
&
$
7*&&
%UHDWKHU &RQWURO9DOYH &KDUJLQJ3XPS 5RWDWLRQ6HQVRU%
IURP2LO&RROHU 2LO)HHG3RUW 5RWDWLRQ6HQVRU$ 9HKLFOH6SHHG6HQVRU
7
&20321(1723(5$7,21'ULYH8QLW
5HDU9LHZRI7UDQVPLVVLRQ
' '
(
(
(
'HWDLO(
7*&&
6HFWLRQ''
(QJLQH6SHHG6HQVRU 6WUDLQHU 2LO3UHVVXUH*DXJH3RUW
6XFWLRQ7XEH 7R2LO&RROHU 6DIHW\9DOYH
+RVH &RQYHUWHU2XWOHW%RVV 6SULQJ
7
&20321(1723(5$7,21'ULYH8QLW
6LGH9LHZRI7UDQVPLVVLRQ
7*&&
&RQYHUWHU,QOHW3UHVVXUH 5HYHUVH&OXWFK3UHVVXUH UG6SHHG&OXWFK3UHVVXUH 3DUNLQJ%UDNH3UHVVXUH
3RUW 3RUW 3RUW 6ZLWFK3RUW
5HJXODWRU9DOYH VW6SHHG&OXWFK3UHVVXUH WK6SHHG&OXWFK3UHVVXUH
3RUW 3RUW
)RUZDUG&OXWFK3UHVVXUH QG6SHHG&OXWFK3UHVVXUH 3DUNLQJ%UDNH5HOHDVH
3RUW 3RUW 3UHVVXUH,QOHW
7
&20321(1723(5$7,21'ULYH8QLW
&URVV6HFWLRQDO'UDZLQJRI7UDQVPLVVLRQ
6HFWLRQ%%㶎
6HFWLRQ$$㶎
㶎
6HFWLRQ&& 7*&&
&KDUJLQJ3XPS 3DUNLQJ%UDNH 5HDU2XWSXW)ODQJH 7RUTXH&RQYHUWHU
3XPS'ULYH6KDIW )URQW2XWSXW)ODQJH VW QG6SHHGV&OXWFK 5HYHUVH&OXWFK
)RUZDUG&OXWFK 2XWSXW6KDIW 'LVWULEXWRU&DS 'LVWULEXWRU&DS
'LVWULEXWRU&DS 'UDLQ3OXJ ,GOHU6KDIW UG WK6SHHGV&OXWFK
㶎5HIHUWR7
7
&20321(1723(5$7,21'ULYH8QLW
&OXWFK6KDIW
&OXWFK VKDIW DVVHPEOLHV FRQWDLQ FOXWFK GLVFV RI WKH
UHVSHFWLYHVSHHGVKLIWVDQGWUDQVPLWRUVWRSSRZHU
$
%
'HWDLO%
'HWDLO$ 7*&&
+XE*HDU %OHHG9DOYH 'LVN 6KDIW
(QG3ODWH 6HDO5LQJ2XWHU 3ODWH 3OXJ
5HWXUQ6SULQJ 3LVWRQ +XE*HDU 6HDO5LQJ
6HDO5LQJ,QQHU
7
&20321(1723(5$7,21'ULYH8QLW
)RUZDUG&OXWFK6KDIW
7*&&
5HYHUVH&OXWFK6KDIW
7*&&
7
&20321(1723(5$7,21'ULYH8QLW
VW QG6SHHGV&OXWFK6KDIW
7*&&
UG WK6SHHGV&OXWFK6KDIW
7*&&
7
&20321(1723(5$7,21'ULYH8QLW
2SHUDWLRQ
,Q2SHUDWLRQ
&OXWFK LV RSHUDWHG E\ WKH SUHVVXUH RLO IURP WKH
WUDQVPLVVLRQFRQWUROYDOYH
3UHVVXUHRLOWUDQVPLWWHGIURPWKHWUDQVPLVVLRQFRQWURO
YDOYH UHDFKHV WKH EDFN RI SLVWRQ WKURXJK WKH RLO
SDVVDJH LQVLGH VKDIW 2LO SDVVDJH LV EORFNHG
EHFDXVHWKHSUHVVXUHRLOSXVKHVWKHEOHHGYDOYH
LQSLVWRQWRZDUGGLVFDQGSLVWRQLVSXVKHG
WRZDUG GLVF 3LVWRQ WUDQVPLWV SRZHU WR WKH
ZKROH RI VKDIW DQG KXE JHDU FRQQHFWHG E\
SUHVVLQJDQGDGKHULQJGLVFDQGSODWH
1RWLQ2SHUDWLRQ
:KHQ SUHVVXUH RLOLV QRW WUDQVPLWWHGIURP WKHWUDQV
PLVVLRQ FRQWURO YDOYH EOHHG YDOYH LV RSHQHG E\
WKH FHQWULIXJDO IRUFH RI VKDIW VR WKH ULVLGXDO
SUHVVXUH RLOLQ WKH SLVWRQ DQG RWKHUV DUH GLVFKDUJHG
WRZDUGGLVF3LVWRQLVSXVKHGEDFNE\WKHUH
WXUQVSULQJEHWZHHQSODWHV
7KHUHDULVHVDFOHDUDQFHEHWZHHQGLVFDQGSODWH
VR VKDIW DQG FOXWFK KXE JHDU URWDWH
VHSDUDWHO\DQGSRZHULVQRWWUDQVPLWWHG
7
&20321(1723(5$7,21'ULYH8QLW
,Q2SHUDWLRQ
'HWDLO$
)URP
&RQWURO9DOYH $
7*&&
1RWLQ2SHUDWLRQ
'HWDLO%
%
7*&&
+XE*HDU %OHHG9DOYH 'LVN 6KDIW
5HWXUQ6SULQJ 3LVWRQ 3ODWH
7
&20321(1723(5$7,21'ULYH8QLW
7UDQVPLVVLRQRI3RZHU
,QSXW
5HYHUVH
*HDU
)RUZDUG
&OXWFK
5HYHUVH
&OXWFK
,GOHU*HDU
VW QG
6SHHGV&OXWFK UG WK
6SHHGV&OXWFK
2XWSXW 7*&
,QSXW*HDU )5*HDU QG+XE*HDU UG+XE*HDU
5HYHUVH*HDU 5+XE*HDU VW+XE*HDU +LJKUDQJH*HDU
)5*HDU ,GOHU*HDU /RZUDQJH*HDU 2XWSXW*HDU
)+XE*HDU ,GOHU*HDU WK+XE*HDU 2XWSXW*HDU
7
&20321(1723(5$7,21'ULYH8QLW
5HYHUVH&OXWFK
)RUZDUG&OXWFK
VW QG
6SHHGV*HDU
7*&
7
&20321(1723(5$7,21'ULYH8QLW
)RUZDUGVW6SHHG
,Q WKH FDVH RIIRUZDUG VW VSHHG WKH IRUZDUG FOXWFK )XUWKHUPRUH WRUTXH LV RXWSXWWHG IURP WKH VW KXE
DQGWKHVWVSHHGSDUWRIWKHVW QGVSHHGVFOXWFK JHDU WRWKHORZUDQJH JHDU DQG HYHQWXDOO\
DUH FRQQHFWHG 7RUTXH FRQYHUWHUWUDQVPLWV WRUTXH WR RXWSXWWHGWRWKHRXWSXWJHDU
)KXEJHDUJHDUHGWRWKHLQSXWJHDU
7RUTXH IURP) KXE JHDU LV WUDQVPLWWHGWR WKH VW
VSHHGKXEJHDUWKURXJK)5JHDUWKHLGOHU
JHDUDQGWKHLGOHUJHDU
,QSXW
)RUZDUG
&OXWFK
VW QG
6SHHGV
&OXWFK
2XWSXW 7*&
3RZHU)ORZ)RUZDUGVW6SHHG
7
&20321(1723(5$7,21'ULYH8QLW
)RUZDUG&OXWFK
VW QG
6SHHGV&OXWFK
7*&
,QSXW*HDU )+XE*HDU ,GOHU*HDU /RZ5DQJH*HDU
)5*HDU ,GOHU*HDU VW6SHHG+XE*HDU 2XWSXW*HDU
7
&20321(1723(5$7,21'ULYH8QLW
)RUZDUGQG6SHHG
,QWKHFDVHRIIRUZDUGQGVSHHGWKHIRUZDUGFOXWFK )XUWKHUPRUHWRUTXH LV RXWSXWWHGIURP QG KXE JHDU
DQG WKH QG VSHHG SDUW RIWKH QG VSHHG FOXWFK DUH WR ORZUDQJH JHDU DQG HYHQWXDOO\ RXWSXWWHG
FRQQHFWHG 7RUTXH FRQYHUWHU WUDQVPLWV WRUTXH WR ) WRRXWSXWJHDU
KXEJHDUJHDUHGWRLQSXWJHDU
7RUTXHIURP)KXEJHDULVWUDQVPLWWHGWRWKHQG
VSHHG KXE JHDU WKURXJK) 5 JHDU DQGLGOHU
JHDU
,QSXW
)RUZDUG
&OXWFK
VW QG6SHHGV
&OXWFK
2XWSXW 7*&
3RZHU)ORZ)RUZDUGQG6SHHG
7
&20321(1723(5$7,21'ULYH8QLW
)RUZDUG&OXWFK
VW QG6SHHGV
&OXWFK
7*&
,QSXW*HDU )+XEJHDU QG6SHHG+XE*HDU 2XWSXW*HDU
)5*HDU ,GOHU*HDU /RZUDQJH*HDU
7
&20321(1723(5$7,21'ULYH8QLW
)RUZDUGUG6SHHG
,QWKHFDVHRIIRUZDUGUGVSHHGWKHIRUZDUGFOXWFK )XUWKHUPRUH WRUTXH LV RXWSXWWHG IURP UG KXE JHDU
DQGWKHVSHHGSDUWRIWKHUG WK6SHHGVFOXWFK WR KLJKUDQJH JHDU DQG HYHQWXDOO\ RXWSXW
DUH FRQQHFWHG 7RUTXH FRQYHUWHUWUDQVPLWV WRUTXH WR WHGWRRXWSXWJHDU
)KXEJHDUJHDUHGWRWKHLQSXWJHDU
7RUTXH IURP ) KXE JHDU LV WUDQVPLWWHG WR UG
6SHHGKXEJHDUWKURXJK)5JHDUDQGLGOHU
JHDU
,QSXW
)RUZDUG
&OXWFK
7*&
2XWSXW
3RZHU)ORZ)RUZDUGUG6SHHG
7
&20321(1723(5$7,21'ULYH8QLW
)RUZDUG
&OXWFK
UG WK
6SHHGV&OXWFK
7*&
,QSXW*HDU )+XE*HDU ,GOHU*HDU +LJK5DQJH*HDU
)5*HDU ,GOHU*HDU UG+XE*HDU 2XWSXW*HDU
7
&20321(1723(5$7,21'ULYH8QLW
)RUZDUGWK6SHHG
,QWKHFDVHRIIRUZDUGWKVSHHGIRUZDUGFOXWFKDQG )XUWKHUPRUH WRUTXH LV RXWSXWWHG IURP WKH WK KXE
WKH WK VSHHG SDUW RI UG WK VSHHGV FOXWFK DUH JHDUWRWKHKLJKUDQJHJHDUDQGHYHQWXDOO\
FRQQHFWHG 7RUTXH FRQYHUWHU WUDQVPLWV WRUTXH WR ) RXWSXWWHGWRWKHRXWSXWJHDU
KXEJHDUJHDUHGWRLQSXWJHDU
7RUTXH IURP ) KXE JHDU LV WUDQVPLWWHG WR WK
VSHHG KXE JHDU WKURXJK) 5 JHDU DQG WKH
LGOHUJHDU
,QSXW
)RUZDUG
&OXWFK
UG WK
6SHHGV&OXWFK
7*&
2XWSXW
3RZHU)ORZ)RUZDUGWK6SHHG
7
&20321(1723(5$7,21'ULYH8QLW
)RUZDUG&OXWFK
UG WK
6SHHGV&OXWFK
7*&
,QSXW*HDU )+XE*HDU WK+XE*HDU 2XWSXW*HDU
)5*HDU ,GOHU*HDU +LJK5DQJH*HDU
7
&20321(1723(5$7,21'ULYH8QLW
5HYHUVHVW6SHHG
,Q WKH FDVH RI UHYHUVH VW VSHHG WKH UHYHUVH FOXWFK )XUWKHUPRUH WRUTXH LV RXWSXWWHG IURP VW KXE JHDU
DQG WKH VW 6SHHG SDUW RI WKH VW QG 6SHHGV WRORZUDQJHJHDUDQGHYHQWXDOO\RXWSXWWHG
FOXWFK DUH FRQQHFWHG 7RUTXH FRQYHUWHU WUDQVPLWV WRRXWSXWJHDU
WRUTXHWR5KXEJHDUIURPUHYHUVHJHDUJHDUHG 3URFHVVHV RI WKH LGOHU JHDU DQG DIWHU DUH DSSOLHG WR
WRLQSXWJHDU WKHRWKHUUHYHUVHVSHHGVKLIWVVLPLODUO\
7RUTXH IURP 5 KXE JHDU LV WUDQVPLWWHG WR VW
VSHHGJHDUWKURXJK)5JHDULGOHUJHDU
DQGLGOHUJHDU
,QSXW
5HYHUVH
&OXWFK
VW QG
6SHHGV&OXWFK
2XWSXW 7*&
3RZHU)ORZ5HYHUVHVW6SHHG
7
&20321(1723(5$7,21'ULYH8QLW
5HYHUVH&OXWFK
VW QG
6SHHGV&OXWFK
7*&
,QSXW*HDU 5+XE*HDU VW+XE*HDU
5HYHUVH*HDU ,GOHU*HDU /RZ5DQJH*HDU
)5*HDU ,GOHU*HDU 2XWSXW*HDU
7
&20321(1723(5$7,21'ULYH8QLW
75$160,66,215(*8/$7259$/9(
7KH WUDQVPLVVLRQ UHJXODWRU YDOYH VR FRQWUROV WKH
SUHVVXUHRLOIURPWKHFKDUJLQJSXPSDVWREHFRQVWDQW
DQG VXSSOLHV LW WR WKH WUDQVPLVVLRQ FRQWURO YDOYH IRU
FRQWUROOLQJWKHFOXWFK
3UHVVXUHRLOHQWHULQJWKH3SRUWRIWKHUHJXODWRUYDOYH
IURP WKH FKDUJLQJ SXPS SDVVHV WKH VPDOO KROH RIWKH
UHJXODWRU VSRRO DQG HQWHUV WKH EDFN FKDPEHU RI WKH
VSRRO :KHQ WKH RLO SUHVVXUH HQWHULQJ WKH EDFN
FKDPEHUULVHVKLJKHUWKDQWKHSUHVVXUHFRUUHVSRQGLQJ
WR WKH VSULQJIRUFH WKHUHJXODWRU VSRROPRYHV WRZDUG
WKHVSULQJDQGWKHSUHVVXUHRLODWWKH3SRUWIORZVIURP
WKHRXWOHWSRUWWRWKHWRUTXHFRQYHUWHU7KLVPRYHPHQW
RIWKHVSRRONHHSVWKHSUHVVXUHDWSRUW3FRQVWDQWSRUW
3 LV FRQQHFWHG WR WKHWUDQVPLVVLRQ FRQWUROYDOYH DQG
SUHVVXUH RLO RI D FRQVWDQW SUHVVXUH LV VXSSOLHG WR WKH
WUDQVPLVVLRQFRQWUROYDOYH7KHSUHVVXUHRLOIURP3RUW
3SDVVHVWKHRLOSDVVDJHLQVLGHWKHWUDQVPLVVLRQFDV
LQJDQGLVWUDQVIHUUHGWRWKHWUDQVPLVVLRQFRQWUROYDOYH
2LO RYHUIORZ SDVVHV WKH RLO SDVVDJH LQ WKH PLVVLRQ
FDVHDQGLVWUDQVIHUUHGWRWKHWRUTXHFRQYHUWHU
7
&20321(1723(5$7,21'ULYH8QLW
1RUPDOO\
6PDOO+ROHRI
5HJXODWRU6SRRO 5HJXODWRU6SRRO 6SULQJ
)URP 7*&&
&KDUJLQJ3XPS
:KHQRYHUIORZLQJ
5HJXODWRU6SRRO 6SULQJ
7R7UDQVPLVVLRQ
&RQWURO9DOYH
)URP 7R7RUTXH 7*&&
&KDUJLQJ3XPS &RQYHUWHU
7
&20321(1723(5$7,21'ULYH8QLW
75$160,66,21&21752/9$/9(
7UDQVPLVVLRQFRQWUROYDOYHWUDQVIHUVWRHDFKFOXWFKWKH
RLO VHQW IURP WKH UHJXODWRUYDOYH DQGPDNHV FKDQJH
RYHURIWKHYHKLFOHWUDYHOGLUHFWLRQDQGVSHHGVKLIW
7UDQVPLVVLRQ FRQWURO YDOYH LV FRPSRVHG RI WKH YDOYH
ERG\ DQG WKH VROHQRLG YDOYHV IRU WKH UHVSHFWLYH
FOXWFKHVDQGFRQWUROVWKHFOXWFKRLOSUHVVXUHE\RSHU
DWLQJWKHVKLIWOHYHUWRDFWXDWHHDFKVROHQRLGYDOYHDQG
E\PRYLQJWKHPRGXODWLRQVSRRORIWKHYDOYHERG\
3URSRUWLRQDOVROHQRLGYDOYHVDUHFRQWUROOHGDERXWWKHLU
RLOSUHVVXUHE\WKHHOHFWULFVLJQDOWUDQVPLWWHGIURPWKH
FRQWUROOHU DQG FDQ REWDLQ RLO SUHVVXUH ZDYHV RI GLI
IHUHQWFKDUDFWHULVWLFVGHSHQGLQJRQWKHYHKLFOHFRQGL
WLRQ
7
&20321(1723(5$7,21'ULYH8QLW
&RQWURO9DOYH
WK6SHHG&OXWFK UG6SHHG&OXWFK QG6SHHG&OXWFK VW6SHHG&OXWFK 5HYHUVH&OXWFK )RUZDUG&OXWFK
5HJXODWRU
9DOYH
&OXWFK 7RUTXH
&RQYHUWHU )LOWHU
/XEULFDWLRQ
6DIHW\
7RUTXH 9DOYH
7RUTXH &KDUJLQJ
&RQYHUWHU 3XPS
&RROHU &RQYHUWHU
7*&&
7
&20321(1723(5$7,21'ULYH8QLW
7*&&
&RYHU WK6SHHG3URSRUWLRQDO VW6SHHG3URSRUWLRQDO
6ROHQRLG9DOYH 6ROHQRLG9DOYH
9DOYH%RG\ UG6SHHG3URSRUWLRQDO 5HYHUVH3URSRUWLRQDO6R
6ROHQRLG9DOYH OHQRLG9DOYH
6ROHQRLG%RG\ QG6SHHG3URSRUWLRQDO )RUZDUG3URSRUWLRQDO6R
6ROHQRLG9DOYH OHQRLG9DOYH
7
&20321(1723(5$7,21'ULYH8QLW
7*&&
)URP
&KDUJLQJ3XPS
6ROHQRLG%RG\ (PHUJHQF\5HYHUVH6SRRO QG6SHHG0RGXODWLRQ WK6SHHG3URSRUWLRQDO
6SRRO 6ROHQRLG9DOYH
9DOYH%RG\ 5HYHUVH0RGXODWLRQ6SRRO QG6SHHG0RGXODWLRQ UG6SHHG3URSRUWLRQDO
6SULQJ 6ROHQRLG9DOYH
&RYHU 5HYHUVH0RGXODWLRQ6SULQJ UG6SHHG0RGXODWLRQ QG6SHHG3URSRUWLRQDO
6SRRO 6ROHQRLG9DOYH
(PHUJHQF\)RUZDUG6SRRO VW6SHHG0RGXODWLRQ UG6SHHG0RGXODWLRQ VW6SHHG3URSRUWLRQDO
6SRRO 6SULQJ 6ROHQRLG9DOYH
)RUZDUG0RGXODWLRQ6SRRO VW6SHHG0RGXODWLRQ WK6SHHG0RGXODWLRQ 5HYHUVH3URSRUWLRQDO6R
6SULQJ 6SRRO OHQRLG9DOYH
)RUZDUG0RGXODWLRQ6SULQJ (PHUJHQF\QG6SHHG WK6SHHG0RGXODWLRQ )RUZDUG3URSRUWLRQDO6R
6SRRO 6SULQJ OHQRLG9DOYH
7
&20321(1723(5$7,21'ULYH8QLW
2SHUDWLRQ
0RGXODWLRQ PHFKDQLVP HQDEOHV VPRRWKHU VSHHG 3URSRUWLRQDOVROHQRLGYDOYHUHJXODWHVWKHRLOSUHVVXUH
FKDQJH E\ YDU\LQJ WKH SUHVVXUH LQFUHDVH ZDYH RU GHSHQGLQJRQWKHHOHFWULFVLJQDOWUDQVPLWWHGIURPWKH
SUHVVXUHGHFUHDVHZDYHRIHDFKFOXWFKGHSHQGLQJRQ FRQWUROOHUDQGWUDQVIHUVRLOWRWKHPRGXODWLRQVSRRO
WKH WKH YHKLFOH FRQGLWLRQ HQJLQH VSHHG YHKLFOH 0RGXODWLRQ VSRRO UHJXODWHV WKH FOXWFK RLO SUHVVXUH
VSHHGDQGRWKHUV DOVRGHSHQGLQJRQWKHRLOSUHVVXUHWUDQVPLWWHGIURP
9HKLFOHFRQGLWLRQLVMXGJHGE\DQDO\]LQJWKHLQIRUPD WKH SURSRUWLRQDO VROHQRLG YDOYH DQG WUDQVIHUV RLO WR
WLRQ HOHFWULF VLJQDO VHQVHG E\ WKH HQJLQH VSHHG WKHFOXWFKSLVWRQ
VHQVRUYHKLFOHVSHHGVHQVRUDQGVKLIWOHYHUXWLOL]LQJ
WKH PLVVLRQ FRQWUROOHU DQG WKH HOHFWULF VLJQDO LV
WUDQVPLWWHG IURP WKH FRQWUROOHU WR WKH SURSRUWLRQDO
VROHQRLGYDOYHGHSHQGLQJRQWKHVKLIWFKDQJH
,Q3UHVVXUH
'HFUHDVH
2LO
3UHVVXUH
,Q3UHVVXUH,Q
FUHDVH
7LPH
7UDQVLWLRQ3RLQW 7*&
&OXWFK2LO3UHVVXUH:DYH
7
&20321(1723(5$7,21'ULYH8QLW
$W1HXWUDO
3UHVVXUHRLOUHJXODWHGE\WKHUHJXODWRUYDOYHIORZVWR
WKHRLOSDVVDJHDRIWKHWUDQVPLVVLRQFRQWUROYDOYH
DQGLVGLYLGHGIORZLQJLQWRWKHRLOSDVVDJHEOHDGLQJ
WR WKH SURSRUWLRQDO VROHQRLG YDOYH DQG WKH RLO
SDVVDJHFRIWKHPRGXODWLRQVSRRO
2LO GRHV QRW IORZ IURP WKH RLO SDVVDJH E WR WKH RLO
SDVVDJH G EHFDXVH WKH HOHFWULF VLJQDO WR EH WUDQV
PLWWHGIURPWKHFRQWUROOHUWRWKHSURSRUWLRQDOVROHQRLG
YDOYHLVVWRSSHGLQWKHQHXWUDOFRQGLWLRQ$OVRRLO
LV FRQILQHG EHWZHHQ WKH RLO SDVVDJH F DQG WKH RLO
SDVVDJH H RI WKH SLVWRQ VR WKH FOXWFK SUHVVXUH LV
QRWUDLVHGEHFRPLQJWKHQHXWUDOFRQGLWLRQ
G
7R3LVWRQ
7*&&
)URP
5HJXODWRU9DOYH
F D E H
3URSRUWLRQDO6ROHQRLG
9DOYH
0RGXODWLRQ6SRRO
7
&20321(1723(5$7,21'ULYH8QLW
6KLIW WR QG 6SHHG IURP 1HXWUDO ,Q 3UHVVXUH ,Q
FUHDVH
,Q3URFHVVRI&OXWFK&RQQHFWLRQ
5HIHUWR2LO3UHVVXUH:DYH$RI7
:KHQ WKH WUDQVPLVVLRQ LV VKLIWHG E\ WKH OHYHU $OVR WKH RLO WUDQVIHUUHG WR WKH RLO SDVVDJH H
HOHFWULFVLJQDOLVWUDQVPLWWHGIURPWKHFRQWUROOHUWR SDVVHVEDFNFKDPEHUJRIPRGXODWLRQVSRRO
SURSRUWLRQDOVROHQRLGYDOYH DQGLVVHQWWREDFNFKDPEHUKRIWKHPRGXODWLRQ
'XULQJRLOSUHVVXUH ZDYH$WKHRLOWUDQVIHUUHGWR VSRRO
RLO SDVVDJH E RI SURSRUWLRQDO VROHQRLGYDOYH $V PRGXODWLRQ VSULQJ LV DVVHPEOHG LQ EDFN
LVUHJXODWHGWRWKHSUHVVXUHFRUUHVSRQGLQJWRWKH FKDPEHU K RI PRGXODWLRQ VSRRO RYHUFRPHV
HOHFWULFVLJQDORIWKHFRQWUROOHUDQGLVWUDQVIHUUHG WKH RLO SUHVVXUH LQ RLOD SDVVDJH H DQG PRYHV
WRWKHRLOSDVVDJHG PRGXODWLRQVSRROULJKWFORVLQJRLOSDVVDJHH
WHPSRUDULO\
2LOWUDQVIHUUHGWRRLOSDVVDJHGLVWUDQVIHUUHGWR
SUHVVXUHFKDPEHUIRIWKHPRGXODWLRQVSRRO (OHFWULF FXUUHQW IURP WKH FRQWUROOHU LV HQODUJHG
RYHUFRPHVWKHIRUFHRIPRGXODWLRQVSULQJDQG JUDGXDOO\DQGUHSHDWVWKHSURFHVVHVLQDQG$VD
PRYHVPRGXODWLRQVSRROWRWKHOHIWFROXPQ UHVXOWWKHFOXWFKRLOSUHVVXUHLVJUDGXDOO\UDLVHG
$VDUHVXOWRLOLVWUDQVIHUUHGIURPWKHRLOSDVVDJH
FWRRLOSDVVDJHHRIWKHFOXWFKSLVWRQDQGWKH
FOXWFKSUHVVXUHLVUDLVHG
K J G I
7RQG6SHHG
&OXWFK
7*&&
F D E H
3URSRUWLRQDO6ROHQRLG9DOYH
0RGXODWLRQ6SRRO
0RGXODWLRQ6SULQJ
7
&20321(1723(5$7,21'ULYH8QLW
$W(QGRI&OXWFK&RQQHFWLRQ ,Q6KLIW'RZQ&RQGLWLRQIURP)RUZDUGQG6SHHG
5HIHUWR3UHVVXUH2LO:DYH%RI7 WRVW6SHHG>DW'66@
)LQDOO\ SUHVVXUHV LQ SUHVVXUH FKDPEHU I DQG 3UHVVXUH LQFUHDVH RI WKH VW 6SHHG FOXWFK SUHV
SUHVVXUHFKDPEHUKEHFRPHHTXDO VXUHLVVLPLODUWR³6SHHG6KLIW&KDQJHIURP1HX
6SULQJLVDVVHPEOHGLQSUHVVXUHFKDPEHUK WUDOWRQG6SHHG´
EXW DV WKH VSRRO GLDPHWHULQWKH SUHVVXUH FKDP 3UHVVXUH GHFUHDVH RI WKH QG 6SHHG FOXWFK
EHU I LV ODUJHU WKDQ WKH GLDPHWHU FRUUHVSRQGLQJ SUHVVXUH LV RSHUDWHG UHYHUVHO\ DQG WKH FOXWFK
WRWKHSUHVVXUHFKDPEHUKSOXVVSULQJIRUFH SUHVVXUH LV JUDGXDOO\ ORZHUHG E\ JUDGXDOO\ ORZ
WKHPRGXODWLRQVSRROLVSXVKHGWRIXOO\VWURNH HULQJ WKH HOHFWULF VLJQDO HOHFWULF FXUUHQW YDOXH
7KHUHIRUH FRPSOHWHO\ RSHQLQJ RLO SDVVDJH F IURPWKHKLJKFRQGLWLRQ
DQG WKH RLO SDVVDJH H 5HIHU WR WKH GUDZLQJ 2YHUODSSLQJ WKH FOXWFK SUHVVXUH RI WKH SDUWQHU
EHORZ FOXWFKSUHVVXUHE\JUDGXDOO\UDLVLQJWKHVW6SHHG
$VDUHVXOWWKHFOXWFKSUHVVXUHDQGWKHUHJXODWRU FOXWFK SUHVVXUH DQG JUDGXDOO\ ORZHULQJ WKH QG
SUHVVXUHEHFRPHHTXDODQGFRQVWDQW FOXWFK SUHVVXUH HOLPLQDWHV ODFN RI WRUTXH DW WKH
WLPH RI VKLIW GRZQ LQ GLJJLQJ DQG DFKLHYHV
VPRRWKZRUNDELOLW\
3URSRUWLRQDO VROHQRLG YDOYH DQG WKH PRGXODWLRQ
VSRRORUJDQL]HDVHWLQWHUPVRIFRQVWUXFWLRQDQG
HQDEOHV REWDLQLQJ FRQVWDQWO\ EHVW PRGXODWLRQ
SUHVVXUH ZDYH E\ FRPELQLQJ WKH SUHVVXUH LQ
FUHDVHFKDUDFWHULVWLFVDQGWKHSUHVVXUHGHFUHDVH
FKDUDFWHULVWLFV 5HIHU WR &OXWFK 2LO 3UHVVXUH
:DYHRQ7
I
7RQG
6SHHG&OXWFK
7*&&
F K H
0RGXODWLRQ6SRRO
0RGXODWLRQ6SULQJ
7
&20321(1723(5$7,21'ULYH8QLW
0$18$/ 6322/ (0(5*(1&< 75$9(/
6322/
,QFDVHWKHVROHQRLGYDOYHFDQQRWEHRSHUDWHGFDXVHG
E\HOHFWULFGLVRUGHUVHJGLVFRQQHFWLRQFKDQJHRYHU
RIWKHFRQWUROYDOYHWR)RUZDUGQG6SHHGRU5HYHUVH
QG6SHHGLVSRVVLEOHE\PDQXDOO\RSHUDWLQJWKLVVSRRO
7KLVVSRROLVXVHGIRUVHOIWUDYHOLQJRIWKHYHKLFOHWRWKH
SODFHRIPDLQWHQDQFHLQDQHPHUJHQF\RUVRPHWKLQJ
,03257$17 3ULRU WR XVH RI WKH PDQXDO VSRRO
VWRS WKH HQJLQH 2SHUDWLQJ WKH
PDQXDO VSRRO ZKLOH WKH HQJLQH LV
UXQQLQJ LV GDQJHURXV EHFDXVH WKH
YHKLFOHFDQEHJLQPRYLQJ
2SHUDWLRQ
)RUZDUGQG6SHHG
:KHQFKDQJHRYHUWR)RUZDUGQG6SHHGLVPDGH
SXVK LQ WKH IRUZDUG HPHUJHQF\ WUDYHO VSRRO
DQG QG HPHUJHQF\ WUDYHO VSRRO HDFK E\
PPDQGWXUQWKHPGHJUHHVNHHSLQJSXVKLQJ
WKHP
2LO UHJXODWHG WRWKH UHJXODWRU SUHVVXUH IORZV LQWR
WKHSDVVDJHEWKURXJKWKHSDVVDJHDRSHQHG
E\WKHIRUZDUGPRGXODWLRQVSRRODQGIORZVWRWKH
IRUZDUGFOXWFKWRFRQQHFWWKHFOXWFK
6LPLODUO\ WKH QG FOXWFK DOVR IORZV LQWR WKH RLO
SDVVDJHIWKURXJKWKHRLOSDVVDJHHRSHQHGE\
WKHQGPRGXODWLRQVSRRODQGIORZVWRWKHQG
FOXWFKWRFRQQHFWWKHFOXWFK
5HYHUVHQG6SHHG
:KHQ WKH IRUZDUG HPHUJHQF\ WUDYHO VSRRO LV
WXUQHG E\ GHJUHHV WKH VSRRO UHWXUQV WR WKH
RULJLQDOSRVLWLRQE\WKHIRUFHRIWKHVSULQJ
6LPLODUO\ WR IRUZDUG QG VSHHG LQ UHYHUVH QG
VSHHG SXVK LQ WKH UHYHUVH HPHUJHQF\ WUDYHO
VSRROE\PPDQGWXUQVLWGHJUHHV
2LO UHJXODWHG WRWKH UHJXODWRU SUHVVXUH IORZV LQWR
WKH RLO SDVVDJH G WKURXJK WKH RLO SDVVDJH F
RSHQHGE\WKHUHYHUVHPRGXODWLRQVSRRODQG
IORZVWRWKHUHYHUVHFOXWFKWRFRQQHFWWKHFOXWFK
,03257$17 $YRLG VLPXOWDQHRXV XVH RI WKH IRU
ZDUGHPHUJHQF\WUDYHOVSRRODQG
WKH UHYHUVH HPHUJHQF\ WUDYHO VSRRO
%UHDNDJH RI WKH FOXWFK FDQ EH
FDXVHG
7
&20321(1723(5$7,21'ULYH8QLW
)URP5HJXODWRU
9DOYH
F D )RUZDUG
&OXWFK E
G
5HYHUVH
&OXWFK
I
QG
&OXWFK
H
,Q2SHUDWLRQRI0DQXDO6SRRO
)URP 7R(DFK
5HJXODWRU9DOYH &OXWFKHV
7*&&
0RGXODWLRQ6SULQJ (PHUJHQF\)RUZDUG6SRRO (PHUJHQF\5HYHUVH6SRRO QG6SHHG0RGXODWLRQ
6SRRO
)RUZDUG0RGXODWLRQ6SRRO 5HYHUVH0RGXODWLRQ6SRRO (PHUJHQF\QG6SHHG
6SRRO
7
&20321(1723(5$7,21'ULYH8QLW
3523257,21$/62/(12,'9$/9( 2SHUDWLRQ
3URSRUWLRQDOVSOHQRLGYDOYHLVXVHGDVDSLORWYDOYHIRU $W1HXWUDO6SRROLVSXVKHGULJKWE\WKHVSULQJ
WKH FOXWFK RLO SUHVVXUH DQG WUDQVIHUV RLO WRWKHPRGX DQG RXWOHW SRUW 6 LVFRQQHFWHG ZLWK WDQN SRUW
ODWLRQ VSRRO E\ UHFHLYLQJ WKH HOHFWULF VLJQDO IURP WKH 7
FRQWUROOHUDQGE\UDLVLQJRUORZHULQJWKHRLOSUHVVXUH $W ([FLWHPHQW 6ROHQRLG YDOYH SXVKHV WKH
VSRRO OHIW ZLWK D IRUFH LQ SURSRUWLRQ WR WKH
HOHFWULF FXUUHQW IORZLQJ DW WKH VROHQRLG 3LORW
SUHVVXUHRLOIORZVWRRXWSXWSRUW6IURPSRUW3DQG
WKHSUHVVXUHDWRXWSXWSRUW6ULVHV
7KLV SUHVVXUH DW RXWSXW SRUW 6 ZRUNV RQ WKH
VKRXOGHUSDUWµD¶RIWKHVSRRO6KRXOGHUSDUWµD¶
KDV GLIIHUHQW VHFWLRQDO DUHDV DQG JHQHUDWHV D
IRUFHWRSXVKWKHVSRRO:KHQWKHSUHVVXUHDW
RXWSXW SRUW 6 ULVHV DQG WKH IRUFH SXVKLQJ WKH
VSRROULJKWEHFRPHVODUJHUWKDQWKHIRUFHGXH
WR WKH VROHQRLG WR SXVK WKH VSRRO OHIW WKH
VSRRO LV UHWXUQHG WR WKH ULJKW WKH SDVVDJH
EHWZHHQ RXWSXW SRUW 6 DQG SRUW 3 LV FORVHG DQG
WKHSUHVVXUHDWRXWSXWSRUW6VWRSVULVLQJ
6
7 3
D
D
7&
6SRRO 6SULQJ 6ROHQRLG
7
COMPONENT OPERATION / Axle
OUTLINE
Axle consists of the differential, final drive, axle shaft, Power from the transmission is transmitted to the front
brakes and others. axle and the rear axle through the propeller shaft. In-
side the axle, power is transmitted to the differential,
and divided into left and right, and drives the axle
shaft and the wheels through the final drive.
PHOTO
Brake Brake
T4GB-03-10-001C
T3-10-1
COMPONENT OPERATION / Axle
DIFFERENTIAL
Differential enables the left and the right drive wheels
to rotate at different rotating speeds in steering of the
vehicle body or traveling on bumpy roads.
4 5 6 7 8 9 10 11
3
2
12
1
13
14
15
16
17
18
19
20
21
T4GB-03-10-002C
T3-10-2
COMPONENT OPERATION / Axle
Function
• Purpose of Differential
When the vehicle body is steered, the inner wheel
turns with a smaller radius, so the outer wheel
needs to rotate faster for smooth steering.
Suppose driving the rear wheel by directly installing
the gear to the propeller shaft with a shaft having no
differential.
In this case, the outer wheel and the rear wheel ro-
tate the same amount. In other words, when the
vehicle body is steered, the outer wheel cannot ro-
tate more than the inner wheel, and as a result,
skidding sideways or tire wear takes place. Also,
the axle shaft is subjected to torsional stress, re-
sulting in unstable transmission of drive force.
On the other hand, in case a differential is installed,
the inner and the outer wheels can rotate at differ-
ent speeds, and the problem mentioned above can
be eliminated.
Extension Line of
Rear Wheel Centers
T3-10-3
COMPONENT OPERATION / Axle
• Principle of Differential
Pinion Pinion
• Operation of Differential T202-03-05-006
In Traveling Straight
In case resistances applied to the axle shafts (7)
and (8) connected by spline to the differential side
gears (2) and (3) are the same, or in case the vehi-
cle body is traveling straight on plane roads, the dif-
ferential pinion gears (1) and (4) remain unrotated.
Differential pinion gears (1) and (4) and the side
gears (2) and (3) remain fixed by being mutually
geared, and rotate in unison with the housing (6)
9 10
connected with the ring gear (9).
In case the constituent portion of the whole is rotat- 1
ing solidly like this, the differential function of the
differential does not work, but gears (1), (2), (3),
and (4) play only the role of joints for connecting the
8
axle shafts (7) and (8).
3 2 7
4 6
T487-03-06-014
T3-10-4
COMPONENT OPERATION / Axle
In Steering
When the vehicle body swings, uneven resistances
are applied to the drive wheels. Therefore, caused by
the difference of the resistances applied to the inner
and outer wheels, the differential pinion gears (1) and
9 10
(4) begin revolving on the side gears (2) and (3), each
rotating round the pinion shaft. As a result, in case the 1
resistance force applied to the shaft (7) is large, the
pinion gears (1) and (4) rotate in the same direction
as the rotational direction on the side gear (2) of the
shaft (7). And the speed of the shaft (7) is lowered, 8
and the amount of the speed reduction is applied to
the shaft (8), working the differential function.
Suppose the ring gear (9) is driven by the drive pinion
(10) at the speed of 100. In the condition of the vehi- 3 2 7
cle body traveling straight, the drive wheels on the
both sides rotate at the same speed.
However, in case the vehicle body swings, and the 4 6
speed of the right drive wheel is lowered to 90, the left
wheel turns at the speed of 100+(100−90)=110 be-
T487-03-06-014
cause the speed of 10(100−90=10) is added to the
speed of the left wheel.
If the ring gear (9) rotates at 100, the summation of
the speeds of the left and right wheels becomes al-
ways 200 regardless of movement of the respective
wheels.
T3-10-5
COMPONENT OPERATION / Axle
TORQUE PROPORTION-
ING DIFFERENTIAL (TPD)
Wheel loader is operated mostly on roads of bad con-
ditions. In case of skidding, working efficiency and tire
lives are lowered. In order to avoid lowering of work-
ing efficiency and tire lives, the axle is provided with
the torque proportioning differential.
Differential pinion gear of the torque proportioning dif-
ferential has an odd number of teeth, and the differen-
tial pinion gear and the side gear have special tooth
profiles. Therefore, the difference of the road resis-
tances to the left and right tires causes deviation of
the gearing locations between the differential pinion
gear and the left and right side gears, and the drive
force transferred to the left and right tires changes.
Forward Rotation
T487-03-06-015C
T3-10-6
COMPONENT OPERATION / Axle
Traveling Straight with the Same Resistances to
Left and Right Tires Differential
Pinion Gear
In case resistances to the left and right tires are the
same, the distances ‘a’ and ‘b’ from the differential
pinion gear center to the respective contact points of
the left and right side gears are the same. Therefore,
Left Side Gear Right Side Gear
the differential pinion gear and the left and right side
gears solidly rotate toward forward, and the drive
forces of the left and right tires become the same.
T487-03-06-016C
T3-10-7
COMPONENT OPERATION / Axle
LIMITED SLIP DIFFERENTIAL (LSD)
(Optional) Operation Principle
Wheel loader, as required by the kind of work, must LSD is so constructed that the clutch disc is inserted
be operated in places where skidding takes place between the pressure ring supporting the spider with
easily like sand and muddy soil. In places like these, the cam and the case, which makes restriction of dif-
Tires can slip even if the torque proportioning differen- ferent movement by keeping the tire speeds the
tial (TPD) is installed. Rotation is transmitted to the same by the resistances of the friction surfaces. Also,
slipping tire, but not to the tires contacting the earth, the variation of the dive force transmitted to the left
so not only the funtion of the wheel loader is wors- and right tires is made larger than the TPD.
ened, but the tire lives are shortened.
In order to avoid this, the limited slip differential (LSD)
provided with the differential movement restriction de-
vice for avoiding different movement of the left and
right wheels is adopted. Drive force transmitted to the
left and right tires further changes.
Ring Gear
Pressure Ring
Side Gear
Pressure Plate
Clutch Disc
Case
T4GB-03-10-003C
T3-10-8
COMPONENT OPERATION / Axle
Traveling Straight with the Same Road Resis-
tances to Left and Right Tires
T3-10-9
COMPONENT OPERATION / Axle
SERVICE BRAKE
Brake adopted is the wet type multi-disc brake, and is
assembled in the differential body of the axle. Four
wheels of this vehicle has all this disc brake.
• In Operation of Brake
Oil pressure from the brake valve works on the
back of brake piston (5) to move brake piston(5),
and brake disc (3) and brake ring (2) is compressed.
Inner surface of brake disc (3) is fitted by spline to
shaft (8) through disk hub (7). Also, the outer sur-
face of brake ring (2) is fixed to differential body (4).
Therefore, the rotation of the pushed and com-
pressed brake disc (3) stops, restricting the vehicle.
• In Release of Brake
When the oil pressure from the brake valve is de-
creased, brake piston(5) is returned by return
spring (6), and brake disc (3) is freed. Restriction of
the vehicle is released.
T3-10-10
COMPONENT OPERATION / Axle
1 2 3 2 3 2
Brake Oil
Pressure
T4GB-03-10-005C
1 - End Plate 3- Brake Disc 5- Brake Piston 7- Disc Hub
2 - Brake Ring 4- Differential Body 6- Return Spring 8- Shaft
• Operation • Release
1 2 3 2 3 2 From 1 2 3 2 3 2 To
Brake Valve Brake Valve
5 5
6
6
T4GB-03-10-007C T4GB-03-10-008C
T3-10-11
COMPONENT OPERATION / Axle
FINAL DRIVE / AXLE SHAFT
Final drive is the device for finally decreasing the
speed in the power transmission system, and of the
planetary gear type. As for power transmission, the
power from the differential, transmitted from the shaft,
rotates the three planetary gears in the ring gear, and
transmits rotation of the planetary carrier to the axle
shaft through the planetary carrier.
Final
Axle Shaft Drive
Ring Gear
Planetary Gear
T4GB-03-10-006C
T3-10-12
COMPONENT OPERATION / Brake Valve
OUTLINE
Brake valve is operated by the brake pedals. (Refer to
the Brake Circuit of SYSTEM/Hydraulic System)
Brake valve sends pilot pressure depending on the
extent of stepping the brake pedal, and operates the
front wheel or rear wheel service brake.
PHOTO
Service Brake
006 105
Brake Pedal
Brake Valve
T4GB-03-11-001C
T3-11-1
COMPONENT OPERATION / Brake Valve
Component Layout
4
Port T
5
Port BR1
Port M1
11
7
Port BR2
Port M2
10
8
9
T4GB-03-11-002C
T3-11-2
COMPONENT OPERATION / Brake Valve
PHOTO
1
Service Brake
105
5
7
BR1
To Front
From Port M2 M1
Service Brake
of Charging Block
BR2 To Rear
From Port M2 M2
of Charging Block Service Brake
T
T4GB-03-11-003C
T3-11-3
COMPONENT OPERATION / Brake Valve
OPERATION
Not in Operation of Brake
1. When the brake valve is not in operation, the ports
(BR1 and BR2) are connected with the tank port
(T) because the spring (9) returns the spools (7
and 8) to the non-operating position.
2. Ports (M1 and M2) and the brake ports (BR1 and
BR2) are blocked by the spools (7 and 8), and the
pressure oil in the service brake accumulator is
retained.
Port T
T4GB-03-11-002C+
T3-11-4
COMPONENT OPERATION / Brake Valve
In Operation of Brake
1. When the brake valve is stepped, spool input (3) 3. Pressure oil on the ports (BR1 and BR2) end
is pushed through roller (2). passes the orifices installed in spools (7 and 8),
Spool input moves the spools (7 and 8) forward and works on the built-in plungers (10 and 11) of
through the spring (5). spools (7 and 8) as the return force (oil pressure
2. When the spools (7 and 8) moves forward, ports rection force) of the spools (7 and 8). Summation
(BR1 and BR2) and port (T) are disconnected. of this oil pressure reaction force and the load of
When spools (7 and 8) are further moved forward, spring (9) balances with the load of spring (5), and
the ports (BR1 and BR2) and the ports (M1 and controls the brake oil pressure on the brake ports
M2) are connected, and the pressure oil of the (BR1 and BR2) end.
accumulator flows out from the ports (BR1 and 4. Deflection and load of spring (5) are fed back as
BR2), beginning braking operation. the stroke and operating force of the brake pedal,
and provides the operator with virtual operation
feeling.
5
T
BR1
M1
7 11
BR2
M2
8 10
T4GB-03-11-005C
T3-11-5
COMPONENT OPERATION / Brake Valve
In Brake Release
1. When the operating force is released, spool input 3. At this time, the ports (BR1 and BR2) and the port
(3) is pushed back by spring (4). (M1 and M2) are blocked by the spools (7 and 8),
2. Compression of spring (5) is released, and spools and the ports (BR1 and BR2) are relieved to the
(7 and 8) are returned to the non-operation port (T).
position by the summation of the oil pressure Pressure oil on the ports (BR1 and BR2) end is
reaction force working on the plunger and load of discharged to the port (T), and the brake operation
the spring (9). is released.
4 T
BR1
M1
7
BR2
M2
T4GB-03-11-006
T3-11-6
&20321(1723(5$7,212WKHUV
3,/276+872))9$/9( PHOTO
Pilot Shutoff Valve
3LORWVKXWRIIYDOYHLVDPXQXDOO\RSHUDWHGFKDQJHRYHU
YDOYH DQG E\ RSHUDWLQJ WKH SLORW FRQWURO VKXWRII OHYHU 6HFWLRQ== 019
URWDWHVWKHVSRROWRWXUQ21DQG2))WKHSLORWSUHVVXUH
WRWKHSLORWYDOYH
6KXWRII3RVLWLRQRI3LORW6KXWRII9DOYH
$W2))RIWKHSLORWVKXWRIIYDOYHWKHSUHVVXUHRLOIURP
WKHSLORWSXPSGRHVQRWIORZWRWKHSLORWYDOYH2LORQ
WKHSLORWYDOYHHQGIORZVWRWKHK\GUDXOLFRLOWDQN
$W21RI3LORW&RQWURO6KXWRII/HYHU
$W 21 RI WKH SLORW VKXWRII YDOYH WKH GUDLQ FLUFXLW LV
EORFNHG DQG WKH SUHVVXUH RLO IURP WKH SLORW SXPS )URP%UDNH 7R3LORW
IORZVWRWKHSLORWYDOYH 3LORW3XPS 9DOYH
7*%&
$ $
=
=
7 7 $
7 3 $ 7
$
7*%&
$([WUD $7R3LORW9DOYH 7)URP3LORW9DOYH 7 )URP3LORW9DOYH2SWLRQDO
$([WUD $([WUD 7([WUD 7 7R+\GUDXOLF2LO7DQN
$7R3LORW9DOYH2SWLRQDO 3 )URP%UDNH3LORW3XPS
7
&20321(1723(5$7,212WKHUV
3523(//(56+$)7
3URSHOOHUVKDIWVDUHLQVWDOOHGEHWZHHQWKHWUDQVPLVVLRQ
DQG WKHIURQW D[OH DQG EHWZHHQ WKHWUDQVPLVVLRQ DQG
WKHUHDUD[OHUHVSHFWLYHO\
3URSHOOHU VKDIW WUDQVPLWV WKH SRZHU IURP WKH
WUDQVPLVVLRQ WR WKH IURQW D[OH DQG WKH UHDU D[OH -RLQW
DGRSWHGLVWKHXQLYHUVDOMRLQWPRVWFRPPRQO\XVHG
PHOTO
Front Propeller Shaft
%HWZHHQ)URQW$[OHDQG7UDQVPLVVLRQ
066
8QLYHUVDO-RLQW
7*%&
PHOTO
%HWZHHQ7UDQVPLVVLRQDQG5HDU$[OH Rear Propeller Shaft
111
8QLYHUVDO-RLQW
7*%&
7
COMPONENT OPERATION / Others
EMERGENCY STEERING CHECK BLOCK
Emergency steering check block is installed between A: from main pump
the main pump and steering valve. B: from emergency steering pump
Built-in check valve is provided for preventing the C: pressure sensor port
delivery oil of the emergency steering pump from D: to steering valve
flowing to the main pump. E: to hydraulic oil tank
A B
Section X-X
A B
C
Y
Section Y-Y
Y
C
E D
E
X X
T4GB-03-12-007C
T3-12-3
COMPONENT OPERATION / Others
EMERGENCY STEERING PUMP
(OPTIONAL)
Emergency steering pump is installed to be started in Emergency steering pump consists of the gear pump,
case supply of the pressure oil from the main pump is electric motor, relief valve, and check valve.
suddenly stopped for one reason or another, and for
supplying pressure oil to the steering valve in place of
the main pump until the time when the vehicle body is
moved to a safe place.
PHOTO
Emergency
Steering
081
T4GB-03-12-008C
T3-12-4