Professional Documents
Culture Documents
Chất lượng điện năng PQ3198A981-00
Chất lượng điện năng PQ3198A981-00
1 Turn on the instrument. in a bundle prevents the instrument from measuring any
current regardless of whether the measurement target is a
PQ3198
A single-phase or three-phase circuit.
mode
Perform zero adjustment after 30-min. warm-up.
2
B C
Load settings.
Configure initial
settings.
(Load settings file from the SD OK
memory card. For more information, E. DATA RESET key
see the instruction manual.) D E Delete displayed measurement Load side
F data. (Data stored on the SD
Connect the instrument to the measurement line. memory card will not be deleted.) Line Make certain that the current
Verify that the connections are correct, referring to the vector
3 F. START/STOP key
flow direction arrow points
K J I H G diagrams and measured values on the [Wiring] screen. Source toward the load side.
[Setting]
4
VIEW: Recording : Steady green
Verify that data has been saved and analyze. Select detailed screen display from each Select and change display ity (i.e., to monitor a power system), select the basic power supply quality measurement pattern.
screen. content and settings.
ing]
8
D. ESC key Monitors voltage factors (dips, swells, inter-
When using battery : Steady ruptions, etc.) and frequency to detect events.
Analyze data on a computer. Cancel selections and changes. red Voltage event
This pattern is used to investigate the cause
detection of equipment malfunctions. The TIMEPLOT
Push to
interval will be set to 1 minute.
1 2
display
Getting For more information, see
the instruction manual.
Initial Perform zero adjustment.
Configure the connection and
Monitors voltage factors (dips, swells, inter-
ready settings current sensor settings. Standard Power
ruptions, etc.), frequency, current, voltage and
current harmonics, and other characteristics
Quality to detect events. This pattern is primarily used
After purchasing the instrument to monitor systems. The TIMEPLOT interval
(first time only)
• Attach the Z1003 Battery Pack to the instrument.
1 Push
(Shown: Connection selected)
will be set to 10 minutes.
Measures rush current. The TIMEPLOT inter-
•
val will be set to 1 minute, and the rush cur-
3
Turn on the instrument and set its clock. Inrush Current rent threshold will be set to 200% of the RMS
Push (The following screen will be displayed.) current (reference value) set during simple
configuration.
-1
Select a course] 10 minutes. All event detection functionality
Perform the pre-measurement inspection. setting value other than manual, start, and stop events is
Push to Display
-2 Insert an SD memory card into the instrument.
Display
display pull-down menu
turned off.
Performs EN50160-compliant measurement.
(Be sure to close the cover.)
-3
pull-down Select Standard-compliant evaluation and analysis
Connect the AC adapter. menu EN50160 can be performed by analyzing data using the
[Voltage event
-4 Connect the voltage cords and current sensors. Select
detection]
application software PQ ONE, which is sup-
plied with the instrument.
-5 Turn on the instrument. Accept For more information about settings, see the
instruction manual.
4 Accept
5 Push (The following screen will be displayed.)
2 3 6
4
5 Verify [Declared input voltage] and [Frequency]
Push These values will be set automatically. Change the values if they are incorrect.
(Zero adjustment will be performed.)
7 Push (A message informing you that the simple configuration process is starting will be displayed.
Select [Yes] to continue with the process.)
5 7
Press the START/STOP key to start recording. Data will be
automatically saved to the SD memory card.
Verifying settings and connections Starting recording
-1. Are measured values or crest factors out of range? -3. Are the voltage and current phase relationships • When recording, the operating mode indi- Operating mode and key operation
If you see any warning indicators, the clamp sensor, range, or shown properly in the vector diagrams? cator on the top right of the screen will
[Setting] [Recording] [Analyzing]
connection settings may be incorrect. Verify the connections and If not, the wiring (connections) to the measurement line or cur- show [Recording].
Change settings Start recording Stop recording
return to step (2) to reconfigure the initial settings. rent sensor orientations may be incorrect. Verify the connections
Warning indicators: Values shown in red as below. and current sensor orientations. • To change a setting, set the operating
mode to [Setting]. (Settings cannot be
changed while recording or analyzing.) Revert to setting mode
Push
1
Alternately, wiring (connections) to the measurement line may ing (connections) to the measurement line or current sensor ori-
Select
be incorrect. Verify the connections. entations may be incorrect.
2
an event Select an
Event icon event from the
Normally shown in white event list
but turns orange when Push details
too many events occur.
Event list details
Event indicator Waveforms at event When multiple events occurred at the same
Counting starts when Push to occurrence time, “1/N” (where N indicates the total number
recording starts. display of events) is displayed at the top of the list.
Reaches capacity at
9999 events. To hold waveforms and values To active the key lock
6 8
After recording has stopped, data can be analyzed on a computer
User settings start date and time, recorded items, and other set- using the application software PQ ONE, which is supplied with
(changing settings) tings as desired. Analysis the instrument.
For more information, see the PQ ONE
Example: To change the [Time Start] start date
1 Push Example: To change the voltage
RMS (Upper limit)
1 Push and time (example: set to 12:00)
instruction manual (on the included CD-ROM).
3 Select
be changed display Easily create graphs to suit your needs Display file data in list form
[(Upper limit)] Push to Set to [12] Organize time plot graphs by convenient times or group Drag and drop folders containing measurement data to
display three phases of data together on a single graph. display a list of settings information and event occurrence
data for all the data contained in the folder.
5
Accept
Converting data
Accept Convert event data and time plot data (binary data) to the
Select the
Calculating demand and integral power
Change the Accept CSV format so that it can be opened with a spreadsheet Display a demand graph, or display the maximum and
level setting threshold
4 Push 3 Push
The time can only be changed when
the [Time Start] setting is [Time].
application on a computer. integrated power values for a specified interval.