Professional Documents
Culture Documents
T6 Guide Line Fluke
T6 Guide Line Fluke
» Consult user documentation. Test with fork and ground probe. TP1 Single Probe, Flat-Tip, Red PN 648128
600 V CAT
1000 V CAT
True
200 A
RMS
Electrical Tester fork opening.
FieldSense Measurement: Fluke voltage/current
TP38 Single Probe, Round-Tip, Red PN 1276841
Requires
Function Range Range Resolution Accuracy [1]
Test Leads
1 FieldSense
No 1000 V 600 V 1V
±(3 % + 3 counts)
600 V CAT
1000 V CAT
200 A
2 6 HO
LD
Current ac true-rms
No 200.0 A 200.0 A 0.1 A
45 Hz to 66 Hz
FieldSense
No 45 Hz to 66 Hz 1 Hz ±(1 % + 2 counts) [3]
frequency (Hz)
3 3 Display Model T6-1000 Model T6-600 Voltage ac true-rms Yes 1000 V 600 V 1V
±(1.5 % + 2 counts)
45 Hz to 66 Hz
gloves, standing on an insulated ladder, or otherwise insulated from earth ground. ● AC220 SureGrip™ Alligator Clips
[3] FieldSense is specified from 16 V to 100 % of range. ● C60 softcase
5 Function Selection/On/Off Auto Off
15 min
Fork opening 17.8 mm
Temperature
Contact FlukeUSA:
6 FieldSense Ground Contact Operating -10 °C to +50 °C (+14 °F to +122 °F) USA: 1-800-44-FLUKE (1-800-443-5853)
Storage -30 °C to +60 °C (-22 °F to +140 °F) Canada: 1-800-36-FLUKE (1-800-363-5853)
Altitude Europe: +31 402-675-200
Operating 2000 m Japan: +81-3-6714-3114
Storage 10 000 m Singapore: +65-6799-5566-5655
PN 4897598 September 2017 Rev. 4, 7/18 Battery Type and Life 2x AA (IEC LR6) 360 hr continuous, typical is 200 hr using the FieldSense function
© 2017-2018 Fluke Corporation. All rights reserved.
Specifications are subject to change without notification. 7 Test Probes/Storage Dock
Temperature coefficient 0.1 x (specified accuracy) / °C for <18°C or >28 °C (<64.4 °F or >82.4 °F)
How to Make Measurements
2 Use the Ground Probe 2 2 Use the Ground Probe 2 Insert Test Probes 2A ● Y shows for measurement ≥30 V
Insert Test Probes
2A into the storage
into the storage
dock
45 Hz - 66 Hz dock
If you see: Solution:
(AC) T6-600 max: 600 V rms CAT III
T6-1000 max: 1000 V rms CAT III
600 V rms CAT IV ● Make sure that your bare hand
● show on the is firmly touching the
display FieldSense Ground Contact
on the battery door.
● Display color is gray
● Check that the black probe is
● VAC measurement
properly stored in the dock.
does not show on
3 display ● Make sure the wire position in
3 3 3 2B the fork opening is correct. See
Hold hand firmly on the Overview section about wire
Hold hand firmly on FieldSense Ground position.
FieldSense Ground Contact ● Measurement is <16 V
2B Contact ● Display color is gray
● Make sure the wire position in
45 Hz - 66 Hz ● VAC measurement
d
oes not show on the fork opening is correct. See
T6-600 max: 600 V CAT III the Overview section about wire
(DC) T6-1000 max: 1000 V CAT III display
LD
position.
HO
LD
HO
600 V CAT IV
4 4
/
4 4
/
600 V CAT
1
200 A
2
600 V CAT
200 A
200 A
200 A
Do not
600 V C
200
1000 V C
600 V CAT
600 V CAT
1000 V CAT
1000 V CAT
overtighten
Display turns
200 A
Display turns screw
600 V CAT
1000 V CAT
green for valid
green for valid Display turns measurement.
HOLD Display turns measurement. green for valid See Tips.
2 AA
green for valid See Tips. measurement.
measurement. See Tips.
See Tips.
5 5
5 5 HOLD
600 V CAT
200 A
600 V CAT
200 A
600 V CAT
1000 V CAT
200 A
HOLD
600 V CAT
1000 V CAT
200 A
Low Battery
Indicator
HOLD
= Hz = =
= Hz