Professional Documents
Culture Documents
DVD 963 Sap 01
DVD 963 Sap 01
DVD
DK S
Advarsel: Klass 1 laserapparat
Laserrudstråling ved åbning når sikkerhesafbrydere er ude af Varning!
funktion. Undgå u tsættelse for stråling. Om apparaten används på annat sätt än i denna bruksanvisning
specificerats, kann användaren utsättas för laserstrålning, som
Bemærk: översjruder gränsen för läserklass 1.
Netafbryderen POWER er sekundært indkoblet og afbryder ikke
strømmen fra nette. Den indbyggede netdel er derfor tilsluttet til Observera!
lysnettet så længe netstikket sidder i stikkontakten. Strömbrytaren POWER är sekundärt kopplad och inte bryter
strömmen fråan nätet Den inbyggda nätdelen är därför ansluten till
elnätet så länge stickproppen sitter i v ägguttaget.
N SF
Observer: Luokan 1 laserlaite + Klass 1 laserapparat
Nettbryteren POWER er sekundert innkoplet. Den Varoitus!
innebygdenetdelen er derfor ikke frakoplet nettet så lenge apparatet Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla
er tilsluttet nettkontakten. tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle
lasersäleilille.
Huom.
Toiminnanvalitsin POWER on kytketty toisiopuolelle, eikä se kytke
laitetta irti sähköverkosta. Sisäänrakennettu verkko-osa on
kytkettynä sähköverkkoon aina silloin, kun pistoke on pistorasiassa.
English
English ------------------------------------------------- 5
Français
Français ---------------------------------------------- 35
Deutsch
Deutsch --------------------------------------------- 65
Nederlands
Nederlands ----------------------------------------- 95
Español
CAUTION Español --------------------------------------------- 125
VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN AVOID EXPOSURE TO BEAM
ADVARSEL
SYNLIG OG USYNLIG LASERSTRÅLING VED
ÅBNING UNDGÅ UDSÆTTELSE FOR
Italiano
STRÅLING
Italiano ---------------------------------------------- 155
VARNING
SYNLIG OCH OSYNLIG LASERSTRÅLNING
NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA
EJ STRÅLEN
VARO!
AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA
NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ
KATSO SÄTEESEEN
VORSICHT
SICHTBARE UND UNSICHTBARE
LASERSTRAHLUNG WENN ABDECKUNG
GEÖFFNET NICHT DEM STRAHL
AUSSETSEN CLASS 1
ATTENTION
RAYONNEMENT LASER VISIBLE ET INVISIBLE
LASER PRODUCT
EN CAS D’OUVERTURE EXPOSITION
DANGEREUSE AU FAISCEAU
NOTE:
Manufactured under license from Dolby PICTURES SHOWN MAY BE
Laboratories. “Dolby”, “Pro Logic” and the DIFFERENT BETWEEN COUNTRIES.
double-D symbol are trademarks of Dolby
Laboratories.
English
Environmental Information ------------------------ 6 Playing a disc --------------------------------------- 23
Supplied accessories -------------------------------- 6 Sound Mode - SACD playback ----------------- 23
Safety Information ----------------------------------- 6 Playing an Audio CD ------------------------------ 24
Symbols Used in this Manual ---------------------- 6 Playing a disc --------------------------------------- 24
Reality reproduced: Super Audio CD ------------ 7 Special DVD features ----------------------------- 24
The next standard: hybrid disc -------------------- 7 Title/Disc Menu ------------------------------------ 24
SACD: reality in sound...and vision --------------- 7 Camera Angle -------------------------------------- 24
Changing the Audio Language ------------------ 24
Subtitle Language ---------------------------------- 24
Functional Overview
Special VCD & SVCD Features ------------------ 25
Front Panel -------------------------------------------- 8
Playback Control (PBC) -------------------------- 25
Rear Panel --------------------------------------------- 9 Special CD, SACD & MP3 Features ------------- 25
Remote Control ----------------------------------- 10 CD text, SACD text and MP3 text ------------ 25
General Features ------------------------------ 25-28
Preparation Moving to another title/chapter ---------------- 25
Basic Connections --------------------------------- 11 Search ----------------------------------------------- 25
Connecting to a TV ---------------------------- 11-12 Slow Motion ---------------------------------------- 26
Connecting to an Audio System ---------------- 13 Still Picture and Frame-by-frame playback ---- 26
Connecting to a Multi-channel Audio/(Video) Scan -------------------------------------------------- 26
receiver with 6 connectors ---------------------- 13 Repeat ----------------------------------------------- 26
Connecting to a Digital Audio Equipment ----- 14 Repeat A-B ----------------------------------------- 26
Inserting batteries into the Remote Control - 14 Shuffle ----------------------------------------------- 27
NTSC/PAL Conversion --------------------------- 15 Time Search ---------------------------------------- 27
Switching On --------------------------------------- 15 Zoom ------------------------------------------------ 27
Menu Bars on TV Screen ------------------------- 15 FTS Video/Audio Program ------------------- 27-28
Temporary Feedback Field Icons --------------- 15 Auto Wake-up Timer ----------------------------- 28
Personal Preferences -------------------------- 16-21 MP3 Disc Features -------------------------------- 29
General Operations ------------------------------ 16 Album/Title Playback ----------------------------- 29
Picture ------------------------------------------- 16-17 MP3 Album/Track/Disc --------------------------- 29
Sound -------------------------------------------- 18-19
Speaker settings (Advance Bass Management) - Access Control
-------------------------------------------------------- 19
Child Lock ------------------------------------------ 30
6 Channel settings ----------------------------- 19-20 Parental Control ------------------------------- 30-31
Delay times ----------------------------------------- 20
Language -------------------------------------------- 21
Features --------------------------------------------- 21
Specifications
Other Feature -------------------------------------- 21 Specifications --------------------------------------- 32
Operation Maintenance
Basic Playback -------------------------------------- 22 Maintenance ---------------------------------------- 33
Playing a DVD-Video ------------------------------ 22
Playing a disc --------------------------------------- 22 Troubleshooting
Smart Resume ------------------------------------- 22 Troubleshooting -------------------------------- 33-34
Video CD and Super Video CD ----------------- 23
Playing a disc --------------------------------------- 23
5
Downloaded from www.Manualslib.com manuals search engine
Introduction
Thank you for purchasing this Philips DVD/SACD ● In cabinet, allow about 2.5cm (1 inch) of free
English
player. This Owner’s Manual explains the basic space all around the player for adequate
operation of this DVD/SACD player. ventilation.
● Do not expose your player to extreme of
temperature or humidity.
Environmental Information ● If the DVD player is brought directly from a cold
All unnecessary packaging has been omitted. The to a warm location, or is placed in a very damp
packaging has been made easy to separate into room, moisture may condense on the lens of the
three materials: cardboard (box), polystyrene disc unit inside the DVD player. Should this occur,
foam (buffer) and polyethylene (bags, protective the DVD player would not operate normally.
foam sheet). Leave the power on for about one hour with no
Your DVD/SACD player consists of materials disc in the DVD player until normal playback is
which can be recycled and reused if possible.
disassembled by a specialised company. Please ● The mechanical parts of the set contain self-
observe the local regulations regarding the lubricating bearings and must not be oiled or
disposal of packaging materials, exhausted lubricated.
batteries and old equipment. ● When the DVD player is switched to
Standby mode, it is still consuming some
power. To disconnect the system from
Supplied accessories the power supply completely, remove the
– Remote control AC power plug from the wall socket.
– Batteries (two AA size) for remote control
– Audio cable Symbols Used in this Manual
– CVBS cable
– SCART cable The below symbols appear in some headings
– Owner’s Manual and notes with the following meanings:
– AC Power Cord
DVD – Description refers to playback of DVD-video discs
6
Downloaded from www.Manualslib.com manuals search engine
Introduction
Reality reproduced: Super Audio SACD: reality in sound...and
English
CD vision
The future in digital sound reproduction is no This SACD player will not only surprise you with
longer limited to a close simulation of reality. The its superior reproduction of almost all existing
new audio standard IS reality! The human ear is audio formats. Connected to your TV, your
no longer capable of distinguishing audible reality SACD player presents VCD and DVD-video
from digital reproduction. At Philips the future information as perfect digital studio-quality
starts today with the Super Audio Compact Disc images with truly 3-dimensional digital multi-
player. This Super Audio CD player combines channel audio.
superior sound quality with the possibility of
playing almost all existing audio and video Super Audio CD
formats with a single player. You will recognize Super Audio CDs by the logo.
The Super Audio standard is based on Direct There are three types of Super Audio CDs:
Stream Digital (DSD) technology. This new single-layer, dual-layer and hybrid discs. Each type
direct-stream digital format comprises a 1-bit may contain two areas of recorded information:
system that has a digital sampling frequency that a High Quality Stereo area and a High Quality
is 64 times higher than that of conventional Multi-channel area.
audio CD. The results are spectacular : a – The single layer disc may contain both
frequency response of over 50k Hz and a 120dB information areas.
dynamic range over the entire audible spectrum. – The dual layer disc may contain both
Mixed with as many of the original frequencies as information areas but a double amount of
possible, the audio information audible for information can be stored on the disc thanks to
human ears sounds much more natural. the second layer.
– The hybrid disc may contain not only both
information areas but also a second, standard
The next standard: hybrid disc CD layer, making it playable on standard CD
The Super Audio CD is the evolution of the CD players.
that provides ultra-high-quality sound. Additional Recorded information may vary per area. This is
features, including multi-channel, can be offered. indicated in the disc inlay. Areas can be selected
On the high density (HD) Super Audio CD you separately before or during playback, while
may have access to separate areas, containing playing Super Audio CDs via the remote control
two-channel stereo and multi-channel. or via the On-Screen Display on your TV.
But that is not all! The hybrid version of the
SACD guarantees backward compatibility with
1 CD Layer that plays on any of
the installed base of CD and DVD players. In your existing CD players
High Density layer containing:
addition to the HD layer, the hybrid disc contains 2 - High Quality DSD Stereo
3 - High Quality DSD Multi-channel
a standard density CD layer with conventional
two-channel stereo CD audio information. The
two layers are read from the same side of the
disc. The HD layer is read by and DVD laser. The
bottom reflective layer with conventional CD
sound is read by the CD laser through the
second, semi-transmissive HD layer.
7
Downloaded from www.Manualslib.com manuals search engine
Functional Overview
Front Panel
English
; PAUSE
– interrupts audio/video playback or
moves to the next frame
STANDBY-ON
– to switch the player to standby mode B PLAY
or ON – star ts audio/video playback
STANDBY INDICATOR 9 STOP
– lights up when the player is in Standby – to stop playback
mode
AUDIO DIRECT
DISPLAY – shut down video circuity to obtain
– shows the current status of the player better audio quality
STANDBY-ON
UPSAMPLING PROGRESSIVE SOUND MODE AUDIO DIRECT STOP PLAY PAUSE
SCAN
PROGRESSIVE SCAN
8
Downloaded from www.Manualslib.com manuals search engine
Functional Overview
Rear Panel
English
Pr/Cr Pb/Cb Y VIDEO OUT
– connect to a TV with Pr/Cr Pb/Cb Y
MAINS (AC Power Cord) inputs
– connect to a standard AC outlet Progressive / Interlace SELECTOR
COAXIAL (Digital audio out) – to switch between Progressive or
– connect to AUDIO inputs of a digital interlace
(coaxial) audio equipment AUX/VCR IN (VIDEO OUT)
OPTICAL (Digital audio out) – connect to a VCR with SCART
– connect to digital (optical) audio TV OUT (VIDEO OUT)
equipment – connect to a TV with SCART
II TV OUT I AUX/VCR IN
VIDEO OUT
Pr/Cr Pb/Cb Y
Progressive
DIGITAL AUDIO OUT Interlace
PCM/MPEG2/AC-3/DTS FRONT CENTER SURROUND
1 L
L L
MAINS
2 R
R R
COAXIAL OPTICAL S-VIDEO AUDIO FRONT SUB WF SURROUND
CVBS
OUT
Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic
discharge may cause permanent damage to the unit.
9
Downloaded from www.Manualslib.com manuals search engine
Functional Overview
Remote Control
English
T-C POWER
POWER B
– select title/chapter 2 – switch DVD player ON or go
DIM T-C DIM FTS SOUND MODE to standby-on mode
– to select 3 different
1 2 3
brightnesses for the display 0-9 numerical key pad
FTS 4 5 6 – select numbered items in a
– activate/deactivate Favorite 7 8 9
menu
RETURN DISPLAY
Track Selection
0
SOUND MODE DISC SYSTEM DISPLAY
É
MENU MENU
É
• for DVD/VCD: Stereo, Dolby
ëÉ Éë
– to display bit rate indicator
STOP PLAY PAUSE
REPEAT REPEAT
A-B
SHUFFLE SCAN
SYSTEM MENU
RETURN – access or remove player’s
– go back to previous menu system menu
DISC MENU T
– access menu of a DVD disc – search forward* / next
chapter or track
1 2 3 4
– (left/right/up/down) select an STOP ( 9 )
item in the menu – stop playback
OK PLAY ( B )
– acknowledge menu selection – star t playback
PAUSE ( ; )
S – pause playback temporarily /
– search backward* / go to a frame-by-frame playback
previous chapter or track
SUBTITLE
REPEAT – subtitle language selector
– repeat chapter, track, title, disc ANGLE
REPEAT (A-B) – select DVD camera angle
– repeat a specific segment ZOOM
SHUFFLE – enlarge video image
– play tracks in random order AUDIO
SCAN – audio language selector
– play the first 10 seconds of each
track/chapter within a disc
English
– Never make or change connections
● Please refer to the instruction books of your TV, with the power switched on.
VCR, Stereo System or other devices as – Connect the DVD/SACD player directly
necessary to make the best connections. to your TV, instead of eg. a VCR, to avoid
● Make one of the following connections, distortion because DVD video discs are
depending on the capabilities of your existing copy protected.
equipment. – Do not connect the DVD/SACD player
The following guidelines are options for the best AUDIO OUT to the PHONO IN of your
picture and sound quality available on your amplifier or receiver.
DVD/SACD player.
Connecting to a TV
Picture
1 Use the CVBS Video Ouput for good picture
1 Connect the SCART (TV OUT) on the DVD
player to the corresponding connector on the
quality.
TV.
2 Use S-Video Output for the better picture
quality. Note:
3 Use SCART or Pr/Cr Pb/Cb Y Output for best – Ensure that the “TV” indication on SCART
picture quality. cable is connected to the TV set and “DVD”
indication on SCART cable is connected to the
Note: DVD player.
– RGB (on SCART) and YUV (Pr/Cr Pb/Cb Y)
output signals are not available at the same time. If your TV is not equipped with SCART input,
– To choose your preferred output connection, you can select the following connection:
refer section “Personal Preferences - YUV/RGB
switching”. If your TV has a CVBS Video input
connector,
Sound 1 Connect the CVBS VIDEO OUT on the DVD
1 Digital audio connections provide the clearest player to the CVBS VIDEO IN on the TV.
sound. Connect the DVD player’s DIGITAL 2 Connect the Left and Right AUDIO OUT on the
AUDIO OUT (either COAXIAL or OPTICAL) DVD player to the Left and Right AUDIO IN on
to your amplifier or receiver. the TV.
Note:
– Digital output is not available for SACD and If your TV has a S-Video input connector,
MP3 discs. 1 Connect the S-VIDEO OUT on the DVD player
to the S-VIDEO IN on the TV.
2 If digital connections are not possible, connect
the DVD player’s LEFT/RIGHT FRONT, 2 Connect the Left and Right AUDIO OUT on the
CENTRE, SUBWOOFER, LEFT/RIGHT DVD player to the Left and Right AUDIO IN on
the TV.
SURROUND connectors to the corresponding
inputs on your multi-channel audio/video
receiver.
3 If both the above connections are not possible,
connect the DVD player’s Left and Right (white
and red) AUDIO OUT to your amplifier, receiver,
stereo or TV.
11
Downloaded from www.Manualslib.com manuals search engine
Preparation
Cinemalink (on SCART) If your TV has a component video (Pr/Cr
English
OR
TO S-VIDEO IN TO VIDEO IN TO AUDIO IN TO COMPONENT
VIDEO IN
II TV OUT I AUX/VCR IN
OR OR Pr/Cr
VIDEO OUT
Pb/Cb Y
Progressive
DIGITAL AUDIO OUT Interlace
PCM/MPEG2/AC-3/DTS
TO S-VIDEO IN TO VIDEO IN TO SCART IN TO AUDIO IN FRONT CENTER SURROUND
TO VCR MAINS
1 L
L L
2 R
R R
COAXIAL OPTICAL S-VIDEO AUDIO FRONT SUB WF SURROUND
CVBS
OUT
II TV OUT I AUX/VCR IN
VIDEO OUT
Pr/Cr Pb/Cb Y
MAINS
DIGITAL AUDIO OUT
PCM/MPEG2/AC-3/DTS
1 L
L
FRONT CENTER SURROUND
L
Progressive
Interlace
Progressive
Interlace
I AUX/VCR IN
VIDEO OUT
Pr/Cr Pb/Cb Y
Progressive
Interlace
FRONT CENTER SURROUND
L L
R R
FRONT SUB WF SURROUND
12
Downloaded from www.Manualslib.com manuals search engine
Preparation
Connecting to an Audio System Connecting to a Multi-channel
English
1 You can also listen to the sound of audio CDs, Audio/(Video) receiver with 6
stereo SACDs and DVD Video discs by connectors
connecting to an optional stereo system.
This DVD/SACD player contains a multi-channel
2 Connect the FRONT LEFT/RIGHT AUDIO
decoder. This enables playback of SACDs &
OUT on the DVD player multichannel audio
DVDs recorded in Multi-channel. You only need
output to the Left and Right AUDIO IN on the
to select Multi-channel using the Sound Mode
stereo system.
key.
Important:
– For the best sound quality with 1 Connect the audio Left and Right outputs for
playback of audio CDs and stereo Front speaker connection (1) to the
SACDs, always use the left and right corresponding input sockets on your receiver
connectors of the high-quality stereo/ using the audio cable supplied.
Multi-channel audio output. The separate 2 Connect the audio outputs for Center speaker
stereo output is intended only for and Subwoofer connection (2) to the
connection to video equipment such as a corresponding inputs on your receiver using an
TV set. optional audio cable.
3 Connect the audio Left and Right outputs for
Surround speaker connection (3) to the
AUDIO SYSTEM
corresponding inputs on your receiver using an
optional audio cable.
Note:
– If the subwoofer is equipped with its own
amplifier, the Subwoofer connection should be
OR OR connected directly to the subwoofer.
TO S-VIDEO IN TO VIDEO IN TO SCART IN TO AUDIO IN
TO VCR
II TV OUT I AUX/VCR IN
VIDEO OUT
2 R
R R
COAXIAL OPTICAL S-VIDEO AUDIO FRONT SUB WF SURROUND
CVBS
OUT
OR OR
TO S-VIDEO IN TO VIDEO IN TO SCART IN
1 2 3
II TV OUT I AUX/VCR IN
VIDEO OUT
Pr/Cr Pb/Cb Y
Progressive
DIGITAL AUDIO OUT Interlace
PCM/MPEG2/AC-3/DTS FRONT CENTER SURROUND
1 L
L L
MAINS
2 R
R R
COAXIAL OPTICAL S-VIDEO AUDIO FRONT SUB WF SURROUND
CVBS
OUT
13
Downloaded from www.Manualslib.com manuals search engine
Preparation
Connecting to a Digital Audio Inserting batteries into the
English
VIDEO OUT
Pr/Cr Pb/Cb Y
Progressive
DIGITAL AUDIO OUT Interlace
PCM/MPEG2/AC-3/DTS FRONT CENTER SURROUND
1 L
L L
MAINS
2 R
R R
COAXIAL OPTICAL S-VIDEO AUDIO FRONT SUB WF SURROUND
CVBS
OUT
14
Downloaded from www.Manualslib.com manuals search engine
Preparation
NTSC/PAL Conversion Menu Bars on TV Screen
English
DVD discs are recorded according to colour ● Operations can be carried out directly via the
system eg. NTSC and PAL. Your TV also operates multiple menu bars on the TV screen.
according to a colour system. ● The following functions are available via the
This DVD player is compatible with NTSC and menu bars. Pressing SYSTEM MENU keys
PAL. To play on this DVD player, the colour repeatedly will toggle through menu bar 1, menu
system of the DVD disc, the TV and the DVD bar 2, menu bar 3 and menu bar OFF:
player should match. If all three are not the same,
Menu bar 1
the DVD may play in only black and white, the
picture may roll continuously or the picture may
appear distorted.
To activate the conversion refer to page 17. From the left,
Personal Preferences ➜ Subtitle Language ➜
Switching On Audio Language ➜ Colour ➜ Sound
1 Connect the AC power cord to the power The following functions are available with
outlet. activated disc via the menu bars:
2 Switch on the TV and DVD/SACD player. Menu bar 2
3 Set the TV to the correct Video IN channel. (eg.
EXT1, EXT2, AV1, AV2, AUDIO/VIDEO, etc -
refer to your TV owner’s manual for detail).
➜ The player display lights up and the default From the left,
screen appears on the TV. Step by step playback ➜ Slow motion ➜
4 If you are using an external equipment (eg. audio Fast motion ➜ Angle ➜ Zoom
system or receiver), turn them on and select the
Menu bar 3
appropriate input source that was used to
connect to the DVD/SACD player output. Refer
to the equipment owner’s manual for detail.
Notes: From the left,
– If you do not have a proper picture or sound, Title ➜ Chapter ➜ Time Search ➜
refer to ‘Troubleshooting’ section. Favourite Track Selection (FTS) ➜ Wakeup Timer
Shuffle Resume
15
Downloaded from www.Manualslib.com manuals search engine
Preparation
Personal Preferences
English
Picture
– TV Shape
Select the aspect ratio of the TV to be
connected. – Video shift
16:9 ➜ when you connect a wide-screen TV to
Use this setting to personalize the position of
the DVD/SACD player.
the picture on your TV by scrolling it to the left
4:3 LETTER BOX ➜ when you connect a
or right.
normal TV to the DVD/SACD player. Displays a
wide picture with black bands displayed on the
upper and lower portions of the TV screen.
4:3 PAN SCAN ➜ when you connect a
normal TV to the DVD/SACD player. Displays
the wide picture on the whole TV screen with a
portion automatically cut off.
16
Downloaded from www.Manualslib.com manuals search engine
Preparation
– Smart Picture – Digital Crystal Clear (on Pr/Cr Pb/Cb
English
Y Progressive Scan Video Out only)
¶ Colour settings (not applicable on
Component Video Output) Digital Crystal Clear (DCC) allows you to
You can select one of five predefined sets of fine-tune the following parametres on the
colour settings and one set (Personal) which you progressive scan output.
can define yourself. ¶ Chroma Delay - is where the Chroma
You can also press SMART PICTURE key (on the (colour) and luma (brightness) signals are not
front panel) to access the colour settings in the synchronised. This allows you to adjust the
menubar. advance delay of the chroma signal to yield a
perfectly clear picture.
¶ Gamma - allows you to adjust the intensity of
the picture non-linearly. A positive value allows
you to bring out low level detail in dark scenes,
while a negative value will emphasize contrast.
¶ Sharpness - allows you to adjust sharpness of
the picture.
¶ DCDi (New Directional Correlation De-
¶ When Personal is selected it allows you to fine- interlacing) - computes and tracks the angle of
tune saturation, brightness and contrast edge to fill in the missing pixel on the TV screen.
¶ Use 3 or 4 keys to adjust the values of these Switching DCDi ON will optimise the image
parametres. Press OK or 1 to exit. quality significantly, especially during the slow
motion playback.
– TV System (NTSC/PAL Conversion) Aspect Ratio - to adjust the ratio of the pictures
on the TV screen.
Allows you to select between PAL, NTSC and
NO LINEAR STRETCH: for display of 4:3 image
AUTO mode depending on your TV. Player’s
on 16:9 TV with non-linear stretching (centre
default setting is set to AUTO.
portion of screen is stretch less than the side).
The conversions supported are as follows:
PILLER BOX: for display of 4:3 image on 16:9 TV
Type
Disc
Format
Output format without stretching.
Selected mode
NTSC PAL AUTO OFF: No aspect ration adjustment
DVD NTSC NTSC
Not
PAL NTSC
¶ True Life - produces a more dynamic picture
PAL PAL PAL
VCD
Supported
by increasing the picture contrast and the colour
NTSC NTSC PAL NTSC
intensity.
PAL NTSC PAL PAL
Note:
1 In the Personal Preferences Menu, select TV – DCDi, Aspect Ratio and True Life adjustment
System. are only applicable on Progressive Scan output.
2 Press 3 or 4 to select PAL, NTSC or AUTO.
Notes:
– If you have a PAL only TV, ensure that your TV
System setting is PAL.
– AUTO can only be selected when using a TV
that supports both the NTSC and PAL systems
(multisystems).
– This setting is applicable for CVBS output on
cinch and SCART only.
– Slight picture distortions may occur due to this
conversion. This is normal.Thus, the AUTO format
is most suitable for the best picture quality.
17
Downloaded from www.Manualslib.com manuals search engine
Preparation
Sound Dolby Surround-compatible: Select this setting
English
– Analogue output
– Night Mode
Select Stereo, Dolby Surround-compatible, 3D
When set to ON, the dynamics of your sound
Sound or Multi-channel.
output are optimised. High volume outputs are
Multi-channel: Select this setting when using a
softened, enabling you to watch your favourite
multi-channel audio/(video) receiver with six
action movie without disturbing others.
inputs. In this mode, the player will perform DTS
decoding or Dolby Digital 5.1-channel decoding
– Karaoke vocal
when applicable, and Dolby Pro Logic decoding
on DVD-Video and Video-CD discs with 2- Put this setting to ON only when a multi-channel
channel sound tracks. No Dolby Pro Logic karaoke DVD is being played. The karaoke
decoding is done with (Super) Audio CD discs. channels on the disc will then be mixed into a
Stereo: In this setting, the 5.1 audio channels are normal stereo sound.
down-mixed to a stereo signal. Select this setting
when connecting to a TV, stereo amplifier/ – SACD Bass Management Bypass
receiver, etc. Allows you (with suitable speaker system) to
Notes: bypass the bass management system for multi-
– Multichannel output and downmixed channel SACD playback.
stereo output are not available This helps to preserve maximum sound quality
simultaneously. of your SACD.
– When multichannel is selected as Warning!
analogue output, the AUDIO OUT (Left/ – When SACD Bass Management Bypass
Right) will deliver the Centre channel data is ON, speaker setting will not be applied
and not the downmixed Left/Right. during multi-channel SACD playback.
18
Downloaded from www.Manualslib.com manuals search engine
Preparation
– PCM Output Speaker settings (Advance Bass
English
Allows to select PCM digital output between Management)
48kHz and 96kHz. When 48kHz has been Allows you to select speaker settings, volume
selected, 96kHz PCM data, (if available on disc) balance and delay time, and to test the speaker
will be converted to 48kHz. settings.
Some 96kHz DVD are copy protected. If your Speaker settings are only active on the Multi-
PCM output selection is 96kHz, the digital output Channel Audio outputs for both DVD and
will be muted to comply with the standards. In SACD.
such cases, select 48kHz to enable digital output.
Movie mode
– CD Upsampling When movie mode is set, speaker settings will
not be applied during playback in the SACD
Allows you to upsample your CD from 44.1 kHz
Stereo mode.
/ 16 bit to various higher sampling rate for
superior CD reproductions.
The selections are: OFF, 96kHz/24bits, 172kHz/
24bits.
The upsampling of CD can be toggle “ON/OFF”
via the AUDIO key on the remote control.
19
Downloaded from www.Manualslib.com manuals search engine
Preparation
6 Channel settings Delay times
English
10,5 0 ms
9 0 ms
Subwoofer
0 ms
0 ms
7,5
On: When you connect a subwoofer
0 ms
0
-5 ms
5 ms
6
10 ms
4,5 -10 ms
15 ms s
15 m
connected 3 Differential
arrival time
s
m
1,5
0 Preferred
FRONT CENTER FRONT 0 1,5 3 4,5 6 7,5 9 10,5 12 Acceptable
LEFT RIGHT Distance from front speakers (m) Not recommended
1
10
30°
°-1
20°
Reference
listening
position
LEFT RIGHT
SURROUND SURROUND
SUBWOOFER
20
Downloaded from www.Manualslib.com manuals search engine
Preparation
Dolby Pro Logic – Status Window
English
If the delay times for Surround Channel and Displays the current status of the player and
Center Channel are set for Digital Surround appears with the menu bar. When disc playback
mode, the delay times for Dolby Pro Logic mode is stopped, it is displayed with the ‘Temporary
will automatically be calculated and set. Feedback Field’ in the default screen. See ‘On-
Screen Display’ information;
Pro Logic Surround Delay Factory setting is ON. Select OFF to suppress
25 20 display of the Status Window.
ms ms
12 15 ms
Distance from surround speakers (m)
10,5 15 ms
9 15 ms
15 mms s
7,5 15 ms
105 m
20 m s
15
25 m s
6 10 ms
30 ms s
4,5 5 ms
30 ms s
30 m
3 Differential
arrival time
s
m
1,5
0 Preferred
0 1,5 3 4,5 6 7,5 9 10,5 12 Acceptable
Distance from front speakers (m) Not recommended
– Low Power Standby
If this is set to ON, the player will go in low-
Language power standby when the standby button is
pressed (front panel or remote control).
Selecting disc languages:
– PBC (Playback Control - for VCD)
Menu/Audio/Subtitle language
The Playback Control can be set to ON or OFF
● This is to select the audio language, subtitle (see section “Special VCD & SVCD Features” for
language and the language used in TV screen
details).
menus or DVD menus which will always be used
for every disc to be played back. – Help text
● If the language selected is not available on the
disc, the default language designated by each disc When set to ON, help text describes the icons
will be selected. selected. Select OFF if you no longer require the
help text.
Features
– Smart Power OFF
– Access Control Puts the set to standby after a predefined time.
Access Control contains the following features: This can be set to ENABLE or DISABLE.
Child Lock - When Child Lock is set to ON, a 4-
digit code needs to be entered in order to Other Feature
playback discs. – Bit Rate Indicator
Parental control - Allows the conditional
Press the DISPLAY key to activate the bit rate
presentation of DVDs containing Parental
indicator. When activated, the bit rate for video
Control information (see ‘Access Control’
and audio, as well as the total bit rate is
section).
displayed.
This is only applicable during playback of
DVD and SVCD discs.
21
Downloaded from www.Manualslib.com manuals search engine
Operation
Basic Playback Playing a title
English
Smart Resume
POW
ER ON
/OFF
22
Downloaded from www.Manualslib.com manuals search engine
Operation
Video CD and Super Video CD Playing a Super Audio CD
English
The current VCD 2.0 and Super Video CD 1.0 ● Super Audio CDs contain only TRACKS
standard features are: ● Select tracks using the menubar on the TV
screen or by pressing the numerical keys directly.
Support following VCD and SVCD formats:
● If SACD-text or CD-text is available on the disc,
Features Video CDs 2.0 Super Video CDs 1.0
Video MPEG-1 MPEG-2
it will be displayed on both the TV screen and
bit rate
resolution NTSC
constant 1,150 Kbps
352x240, 29.97Hz
variable up to 2.6 Mbps
480x480 interlaced, 29.97Hz
player’s front panel.
resolution PAL 352x288, 25Hz 480x576 interlaced, 25Hz ● Favourite Track Selection (FTS) programming is
Still picture (photo) MPEG-1 MPEG-2 (1 Frame)
resolution NTSC 352x240, 704x480 480x480, 704x480 NOT possible on SACD discs.
resolution PAL 352x288, 704x576 480x576. 704x576
Audio MPEG-1 layer II MPEG-1 layer II
sampling 44.1KHz 44.1KHz
bit rate 224Kbps 32-384Kbps
audio channels 1 stereo / 2 mono < 2 stereo / 4 mono
surround sound Stereo with Dolby Pro-Logic MPEG-1 (5+1) extension
Overlay graphics/text overlay video plane
sub-channels <= 4
coding 4 colour CLUT (2bits/pixel) Playing a disc
Following formats can’t be supported in
1 Insert a disc and close the tray, playback starts
automatically.
VCD:
– HQ-VCD is encoded at 2.4Mbps or 2.6Mbps ➜ The TV screen will display the number of
– XVCD (eXtended VCD) with higher resolution tracks for selection, current playing status and
and data rate. current playing layer.
– The file ending with “DIVX” format. 2 Playback will stop at the end of the disc.
3 To stop playback, press STOP.
● Video CDs may have one or more TRACKS, and
TRACKS may have one or more INDEXES.
● To make easy and convenient access, you can
Sound Mode - SACD playback
move between TRACKS and INDEXES. ¶ If the default Sound mode is set to multi channel
● Some Video CDs have Play Back Control (PBC), and the inserted disc does not contain this
which is a predefined playback sequence stored mode, the player will automatically select the
on the disc (see Playback Control section). stereo mode.
¶ On hybrid discs (with SACD and CD layers), the
VIDEO CD
TRACK 1 TRACK 2
player will always start playing the SACD layer.
INDEX 1 INDEX 2 INDEX 1 INDEX 2 INDEX 3
¶ While the SACD disc is being played, the
currently played layer is shown on the player
front display as follows:
SA 6 (for SACD Multi channel)
SA 2 (for SACD stereo)
Playing a disc CD (for CD layer of SACD)
1 Insert the disc and close the tray, playback starts ¶ You can switch between SACD multi channel
automatically. and SACD stereo layers (depending on
➜ The number of tracks and the total playing availability of the mode on the disc) while the
time of the disc will appear on the TV screen and disc is playing by pressing the Sound Mode
DVD player’s display. button on the remote control or the player
2 Press PLAY. front. The mode change will be indicated on the
➜ The current track number and its elapsed player front display.
playing time will be displayed. ¶ Switching between the SACD and CD layer is
3 Playback will stop at the end of the disc. not possible during playback.
4 To stop playback, press STOP.
5 Disc Resume feature is also applicable for VCDs
and SVCDs (see “Smart Resume” section).
23
Downloaded from www.Manualslib.com manuals search engine
Operation
1 Press STOP to stop the playback. Title/Disc menu
English
24
Downloaded from www.Manualslib.com manuals search engine
Operation
Special VCD & SVCD Features General Features
English
Note:
Playback Control (PBC) – Unless stated, all operations described are
Playback control is a feature on some Videos based on remote control use. Some operations
CDs / Super Video CDs that enables interactive can be carried out using the menu bar on the TV
use. screen.
Video CD discs with Playback Control features
enables user to access a selected track directly Moving to another title/chapter
from the disc menu. DVD VCD
1 Load a Video CD with PBC and press PLAY.
2 Go through the menu with the keys indicated on When a disc has more than one title/track or
the TV screen until your chosen passage starts to chapter, you can move to another title/chapter as
follows:
playback. If a PBC menu consists of a list of
tracks, you can select a track directly. 1 Press SYSTEM MENU, then select W or X in
3 Enter your choice with the numerical keys (0-9). the menu bar.
4 Press RETURN to go back to the previous menu,
2 Press 34 or numerical keys to select a title/
if applicable on the menu. chapter.
5 You may also select PBC OFF under Personal CD SACD
Preferences.
1 Press T or S briefly during playback to go
➜ When set to OFF, PBC menus are not
to the next track or to return to the beginning
activated for further playback.
of the currect track respectively.
2 Press S twice briefly to step back to the
Special CD, SACD & MP3 previous track.
Features 3 To go directly to any track, enter the track
number using the numerical keys (0-9).
CD text, SACD text and MP3 text
1 Some CD, SACD or MP3-CD discs may contain Search
text information (eg. track name, album name, DVD VCD SACD
artist name etc.) which will appear on the DVD/ 1 Select (FAST MOTION) in the menu bar and
SACD player and TV screen during playback. press 4.
2 By default, CD text display is set to ON. 2 Use the 1 2 keys to select the required speed: -
3 To switch off the CD text display, press DISPLAY 32, -8 or -4 (backward), or +4, +8, +32
on the remote control during playback. (forward).
4 Press DISPLAY on the remote control again to 3 Select 1 to play the disc at normal speed again.
switch on the text display mode. 4 To exit FAST MOTION mode, press PLAYor 3.
CD
● To search forward or backward through different
speeds, you can also hold down T or S
for more than two seconds.
25
Downloaded from www.Manualslib.com manuals search engine
Operation
Slow Motion DVD VCD VCD CD SACD
English
26
Downloaded from www.Manualslib.com manuals search engine
Operation
Time search DVD VCD 6 To exit ZOOM mode, select zoom factor to
English
“Off ” (zoom factor 1) in the menu bar.
The Time Search function allows you to start
playing at any chosen time on the disc.
1 Select (TIME SEARCH) in the menu bar and
press 4.
➜ Playback will pause.
➜ The elapsed playing time is displayed in a time
edit box.
FTS Video/Audio Programme
2 Enter hours, minutes and seconds from left to
right in the time edit box using remote control ● The FTS-Video function allows you to store your
numerical key pad. favourite titles and chapters (DVD) and favourite
➜ Each time an item has been entered, the next tracks and indexes (VCD, CD) for a particular
item will be highlighted. disc in the player memory.
3 Press OK to confirm the selected time. ● Favourite Track Selection (FTS) list contains up to
➜ The time edit box will disappear and playback 20 items (titles, chapters).
starts from the selected time position on the ● The most recent programme list will be placed
disc. on top of the existing list.
DVD VCD
Storing a Programme
1 Load a disc and stop playback.
2 Select VIDEO FTS c in the menu bar.
4 Press SYSTEM MENU to remove the menu bar. 3 Press 4 to open the menu bar.
➜ The VIDEO FTS c menu appears.
Zoom DVD VCD
Storing titles/tracks
The Zoom function allows you to enlarge the
1 Press 4 to select TITLES/TRACKS.
video image and to pan through the enlarged
2 Use 2 and 1 to select the require title/tracks.
image.
3 Press OK to store the entire selected title/tracks.
1 Select (ZOOM). ➜ The title number will be added to the list of
2 Press 3/4 to activate the ZOOM function and selections.
select the required zoom factor: 1.33 or 2 or 4.
➜ Playback will continue.
➜ The selected zoom factor and ‘Press OK to
pan’ appears below the menu bar.
➜ The zoomed picture will appear on the TV
screen.
3 Press OK to confirm the selection.
➜ The panning icon appears on the screen.
4 Use the 1 2 3 4 keys to pan across the screen.
5 When OK is pressed only the panned picture
will be shown on the screen.
27
Downloaded from www.Manualslib.com manuals search engine
Operation
Storing chapters/indexes Switching a Programme ON/OFF
English
1 Press 4 on the selected chapter/indexes number. 1 Use 34 to move and select desired tracks.
➜ The chapter/indexes number will be 2 Press 2 or 1 to select either ON or OFF.
highlighted.
2 Use 2 and 1 to select the required chapter Erasing a track in a Programme
number. 1 Use 4 to go to the programmed tracks.
3 Press OK to confirm the selection. 2 Use 2 and 1 to select the required number.
➜ The selected chapter/indexes confirmation 3 Press OK to erase the selection.
will be added to the list of selections. 4 Press SYSTEM MENU to exit.
4 Press SYSTEM MENU to exit the VIDEO FTS
c menu. Erasing all selections
● Use 4 to select CLEAR ALL and press OK.
Switching a Programme ON/OFF ➜ All selections will be erased.
1 Use 34 to move and select desired tracks.
2 Press 2 or 1 to select either ON or OFF.
28
Downloaded from www.Manualslib.com manuals search engine
Operation
MP3 Disc Features Album/Title
English
Support following MP3-CD formats This feature allows you to view and select the
(ISO9660 format): next or previous MP3 disc Album/Title.
● Max. 30 characters 1 Press 3/4 to scroll through the previous or next
● Max. nested directory is 8 levels Album.
● The max. ALB number is 32 2 Press 1/2 to scroll through the previous or next
● Supported VBR bit-rate Track.
● Supported sampling frequencies for MP3 disc 3 You can also select the desired album/track
are: 32 kHz, 44.1 kHz, 48 kHz number directly using the numeric keys on the
● Supported Bit-rates of MP3 disc are: 32, 64, 96, remote control.
128, 192, 256 (kbps) Note:
– In STOP mode: numbers are used for
Following formats can’t be supported ALBUM selection.
● The files like *.WMA, *.AAC, *.DLF, *.M3U, *.PLS – In PLAY mode: numbers are used for TRACK
● Chinese filenames selection.
● The non-session closed discs
● The discs recorded under UDF format
29
Downloaded from www.Manualslib.com manuals search engine
Access Control
Child Lock DVD VCD – Each time a ‘child safe’ disc is played, it will be
English
Notes:
– The player memory can maintain 120
authorised (‘Child safe’) disc titles. A disc will be
placed in the list when ‘Play Always’ is selected.
30
Downloaded from www.Manualslib.com manuals search engine
Access Control
Activating/Deactivating Parental Changing the 4-digit code
English
Control 1 When disc playback is stopped, select ACCESS
1 When disc playback is stopped, select ACCESS CONTROL in the Personal Preferences menu
CONTROL in the Personal Preferences menu using the 3/4 keys.
using the 3/4 keys. 2 Enter the current 4 digit code.
2 Enter your 4-digit code. If necessary, enter the 3 Move to CHANGE CODE using the 4 and
code a second time. press the 2 key.
3 Move to Parental Control using the 3/4 4 Enter the new 4-digit code.
keys. 5 Enter the code a second time and reconfirm by
4 Move to value adjustment (1-8) using the 2 key. pressing OK.
5 Then use the 3/4 keys or the numerical keys on 6 Press 1 to exit the menu.
the remote control to select a rating from 1 to 8 ➜ The new 4 digit code will be take effect.
for the disc inserted.
Rating 0 (displayed as ‘– –’): If you forget your 4 digit code
Parental Control is not activated. The Disc will be 1 Press 9 to exit the ‘Child Safe’ screen.
played in full. 2 Select ACCESS CONTROL in the Personal
Preferences menu using the 3/4 keys.
Ratings 1 to 8:
3 The 4-digit code can be cancelled by pressing 9
The disc contains scenes not suitable for children.
four times in the ‘Access Control’ dialog.
If you set a rating for the player, all scenes with
4 You can then enter a new code (twice!) as
the same rating or lower will be played. Higher
described above in ‘Changing the 4 digit code’.
rated scenes will not be played unless an
alternative which has the same rating or lower is
available on the disc. If no suitable alternative is Parental Control Disclaimer
found, playback will stop and the 4-digit code has This DVD/SACD player features the
to be entered. PARENTAL CONTROL system which is to
6 Press OK or 1 to confirm, then press 1 again to activate when playing DVD discs furnished with
certain software coding only.
exit the Personal Preferences menu.
Also note that at the time of release of this
DVD/SACD player, certain aspects of the
technical standards had not been settled
between set makers and the disc industries.
On this basis, Philips cannot guarantee the
functioning of the PARENTAL CONTROL
system and denies any liability associated with
unintended watching of disc content.
If in doubt, please make sure the disc plays
Country according to your PARENTAL CONTROL
settings before you allow children access to the
1 When disc playback is stopped, select ACCESS
player.
CONTROL in the Personal Preferences menu
using the 3/4 keys.
2 Enter the 4-digit code.
3 Move to CHANGE COUNTRY using the 4
key.
4 Press the 2 key.
5 Select a country using 3/4.
6 Press OK or 1 to confirm, then press 1 again to
exit the menu.
31
Downloaded from www.Manualslib.com manuals search engine
Specifications
PLAYBACK SYSTEM
English
32
Downloaded from www.Manualslib.com manuals search engine
Maintenance
Cleaning the Cabinet Cleaning the disc lens
English
¶ Use a soft cloth slightly moistened with a mild ¶ After prolonged use, dirt or dust may
detergent solution. Do not use a solution accumulate at the disc lens. To ensure good
containing alcohol, spirits, ammonia or abrasives. playback quality, clean the disc lens with Philips
CD Lens Cleaner or any commercially available
Cleaning Discs cleaner. Follow the instructions supplied with the
¶ When a disc becomes dirty, clean it with a cleaner.
cleaning cloth. Wipe the disc from the centre out.
Do not wipe in a circular motion.
¶ Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic
spray intended for analogue records.
Troubleshooting
WARNING
Under no circumstances should you try to repair the system yourself, as this will invalidate the
warranty. Do not open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair.
Problem Solution
No power – Check if the AC power cord is properly
connected.
No picture – Check if the TV is switched on.
– Check the video connection.
Distorted picture – Sometimes a small amount of picture distortion
may appear .This is not a malfunction.
Completely distorted picture or – Make sure the NTSC/PAL setting at the DVD
black/white picture with DVD/SACD player matches the video signal of your television.
or Video CD (See NTSC/PAL Conversion/Settings)
No sound or distorted sound – Adjust the volume.
– Check that the speakers are connected correctly.
33
Downloaded from www.Manualslib.com manuals search engine
Troubleshooting
Problem Solution
English
If you are unable to remedy a problem by following these hints, consult your dealer or service
centre (HOTLINE).
34
Downloaded from www.Manualslib.com manuals search engine