Professional Documents
Culture Documents
Panasonic 1014
Panasonic 1014
Panasonic 1014
SBPAC1908013CE
R32
R32 Models
Model No.
Indoor Unit
Type Indoor Unit Type 36 50 60 71 100 125 140
U3 4-Way Cassette S-3650PU3E S-6071PU3E S-1014PU3E
Outdoor Unit
Type Outdoor Unit Type 36 50 60 71 100 125 140
Single Split (1-phase) U-36PZ3E5 U-50PZ3E5 U-60PZ3E5 U-71PZ3E5 U-100PZ3E5 U-125PZ3E5 U-140PZ3E5
PZ3
Single Split (3-phase) - - - - U-100PZ3E8 U-125PZ3E8 U-140PZ3E8
External static pressure should be set during initial operations after installation (before
the cooling and heating test run).
When operating with group control (connecting multiple indoor units with one wired
remote controller), make the middle static pressure duct type to the main unit.
Line A (set at
No
shipment) on the PQ diagram
designed and installed
Yes
Set static pressure setting No
to manual setting mode.
Yes
Yes
Operation checks for external static pressure settings (*Note (2)) Auto airflow volume control
See the section “ Operating the High-spec Wired Remote Controller” or “ Operating the Timer Remote operations (*Note (5)) See the section
Controller” on page 1-11-1-2-17 or 1-11-1-2-19. “ Operating the High-spec Wired
Check if the setting is within the range of use on the PQ diagram. Remote Controller” or “ Operating
If out of range, adjust until it becomes within the range of use. the Timer Remote Controller” on page
In the case of identical setup, it is possible to omit this operation check if judged unnecessary. 1-11-1-2-17 or 1-11-1-2-19.
NOTE
(1) Check the following items before performing the setting-check operations or auto airflow volume operations.
1) Check to make sure that the electrical wiring and ducting have been completed. Activate the stand-by mode. In particular, make
sure that the closed damper located in the middle of the duct is open, if installed. Also, make sure that air filters have been
installed inside the air inlet duct.
Check to make sure air is not leaking from the joints.
2) If multiple air outlets and air inlets are included, adjust the airflow volume ratio of all of them until they meet the design airflow ratio.
3) Make sure the address setting has been completed.
(2) The operation check will be completed in approximately three minutes if the settings have been made correctly. The settings will be
modified if they are out of the range of use (maximum 30 minutes).
If this is not completed within 31 minutes, check whether the air speed is set to “H” or not.
(3) See Table 1-11-1-2-2, 1-11-1-2-3 and Fig. 1-11-1-2-2 for details on the relationship between the value of item code “b0” and the 1
external static pressure.
(4) When set in group control (connecting multiple indoor units with one wired remote controller), set each indoor unit to item code “b0”.
When amending the setting after selecting [b. Manual setting] (due to airflow path changes, etc.), it is necessary to cancel [b. Manual
setting] (change the dip switch). When [b. Manual setting] has not been cancelled, [c. Manual setting] and [d. Auto airflow volume
setting] will be activated if selected, but [b. Manual setting] takes precedence when the power is switched back on after power
outages, etc.
(5) If this is not completed within 8 minutes, check the operation mode, air speed and air inlet temperature.
(6) When set in group control (connecting multiple indoor units with one wired remote controller), the test run operations display will
disappear once the external static pressure setting check or auto airflow volume control operation check have been completed for the
main unit. However, it is not possible to determine whether sub-units have completed. The test run operation display will disappear
after one hour even if the external static pressure setting check or auto airflow volume control operation check have not been
completed.
CAUTION
• Be sure to check that the external static pressure is within the range for use and then make the setting. Failure to observe
this may result in insufficient airflow or water leakages. See Fig. 1-11-1-2-2 for the external static pressure setting range.
• There are cases in which automatic variable dampers and other mounted items may trigger the P12 alarm on systems that
modify the external static pressure when the auto airflow volume control operations or setting check operations are carried
out if high external static pressure is lowered. In this event, lower the dampers, etc., so that the external static pressure
reaches its lowest level, and then carry out the auto airflow volume control operations or setting check operations.
• Be sure to set the [External Static Pressure Setting] once again after amending the airflow path for the duct or air outlet after
setting the external static pressure.
• Set the air inlet temperature within the range for use. The auto airflow volume control will not function if the air inlet
temperature is over 45°C or if operation is other than fan mode.
Table 1-11-1-2-1
External static pressure at the Setting example
DIP switch
time of rated airflow volume
TP6
TP3
TP1
TP6
TP3
TP1
ON 1: OFF
SW001
ON
10 Pa 2: OFF
TP6
TP3
TP1
ON
3: ON
1 2 3
1 2 3 1 2 3
ON
50 Pa Fig. 1-11-1-2-1
1 2 3
TP6
TP3
TP1
ON
110 Pa
1 2 3
1 Operating the High-spec Wired Remote Controller 4. Select the “Set data” by pressing the or
(CZ-RTC5B) button.
Select one of the “Set data” among “0001” – “0010 ”
according to the desired external static pressure setting by
pressing the or button.
20:30 (THU)
Then press the button.
1-1 B0 -001
Sel. Next
1-11-1-2-17
Auto External Static Pressure Setting Operation 9. Press the button. Test run will be started. 1
Test run setting mode screen appears on the LCD display.
6. Keep pressing the , and buttons
simultaneously for 4 or more seconds. 20:30 (THU)
The “Maintenance func” screen appears on the LCD TEST
MODE FAN SPEED
display. COOL
Maintenance func 20:30 (THU)
1. Outdoor unit error data FLAP
2. Service contact
3. RC setting mode 10. Set the operation mode to “ (MODE FAN)” and fan
4. Test run
Sel. Page [ ] Confirm speed mode to “ (FAN SPEED)” by pressing the
or button or or button.
7. Press the or button to see each menu.
Then press the button.
If you wish to see the next screen instantly, press the
or button. 20:30 (THU)
TEST
Select “4. Test run” on the LCD display and press the FAN SPEED
MODE
button. FAN
FLAP
Maintenance func 20:30 (THU)
1. Outdoor unit error data
2. Service contact The fan motor will be activated, the auto external static
3. RC setting mode pressure setting operation and setting-check operation will
4. Test run be performed for about 3 to 30 minutes.
Sel. Page [ ] Confirm The fan speed will change automatically while these
operations are in progress. When these operations
The “Test run” screen appears on the LCD display. completed, “TEST” will be disappeared from the LCD
display.
Test run 20:30 (THU)
20:30 (THU)
Test run
FAN SPEED
OFF MODE
FAN
Change [ ] Confirm
FLAP
Change the display from OFF to ON by pressing the
NOTE:
or button. Then press the button.
The auto external static pressure setting operation
Test run 20:30 (THU) and setting-check operation will not be performed
[ ] START
1-11-1-2-18
1 Operating the Timer Remote Controller Table 1-11-1-2-3 Setting the external static pressure
(CZ-RTC4) Indoor unit type Item code
Setting Item Code “ ” 3650 6071 1014
Outdoor unit type
1. Press and hold down the , and buttons
simultaneously for 4 or more seconds. – 100 125 140
( , the Unit No., Item Code and Detailed Data will External static pressure of the rated
airflow volume (Pa)
blink on the LCD display.)
150 150 150
2. The indoor unit numbers in the group control will be
sequentially displayed whenever the Unit Select button is 140 140 140
pressed . 130 130 130
Only the fan motor for the selected indoor unit will operate
during this time. 120 120 120
110 110 110
3. Specify the “ ” item code by pressing the
/ buttons for the temperature setting buttons 90 90 90
and confirm the values. 70 70 70
(“ ” set at shipment )
50 50 50 *
4. Press the / buttons for the time to amend the
values for the set data. 30 * 40 * 30
See Table 1-11-1-2-3 and Fig. 1-11-1-2-2 and select a 10 10 10
value between “ ” and “ ”.
No auto airflow volume setting
Select “ ” if the auto airflow volume setting is
activated. Auto airflow volume setting
5. Press the button. * Setting at shipment
The display will stop blinking and remain illuminated.
6. Press the button. The fan motor will stop operating
and the LCD display will return to the normal stop mode.
3
Auto Airflow Volume Control Operations and External
Static Pressure Setting-Check Operation
1. Press and hold down the button for 4 or more seconds.
“ ” will be displayed on the LCD display.
2. Press the button to start the test run.
A
NOT E 1, 6 4 5 1 2
Auto airflow volume control operations and external static *Failure to set this parameter may result in decreased
pressure setting-check operations will not be performed airflow and condensation.
unless the above settings are made.
4. The fan motor will be activated and auto airflow volume
control operations or external static pressure setting-check
operations will be started.
The power of the airflow will change while these operations
are in progress.
The external static pressure setting-check operations and
auto airflow volume control operations will be completed in
about 3 to 30 minutes.
“ ” display will be disappeared from the LCD display.
1 3 2, 5
1-11-1-2-19
Indoor Units Type 3650 (36) External static pressure 130Pa, 50Pa 1
180
U-36
160
S-3650
140 H
in e
it l
Lim
PQ diagram (Fig. 1-11-1-2-2) 100
20
ine
it l
120
Lim
0
10 15 20
100 l i ne H Airflow Volume (m 3/minute)
it
m M
L Li
80 ne
it li External static pressure 120Pa, 30Pa
Lim
60 180
L
40 160
20 ne
Limit li 140
External static pressure (Pa)
H
0 120
10 15 20
ne
M
i
Airflow Volume (m 3/minute) it l
Lim
100
20 M
L
ine
M
A
it l
120
Lim
0
10 15 20
100 Airflow Volume (m 3/minute)
i ne H
80 L it l
Lim M ne External static pressure 110Pa, 10Pa
i t li
60 Lim 180
40 L
160
20
140
External static pressure (Pa)
0 Limit line H
10 15 20 120
Airflow Volume (m 3/minute) M
100
e
l in
it
m
80
Li
L
60
e
40 it lin
Lim
ne
20 Limit li H
L M
0
10 15 20
Airflow Volume (m 3/minute)
1 Indoor Units Type 3650 (50) External static pressure 130Pa, 50Pa
180
U-50 U-100
160
S-3650 S-3650 S-3650 H
e
lin
120
it
Indoor Fan Performance
m
Li
100
PQ diagram (Fig. 1-11-1-2-2) L
80
H
External static pressure 150Pa, 90Pa e
60 it li
ne it lin
180 i m M Lim
L
H 40 L
160
M 20
External static pressure (Pa)
in e
140
it l
0
Lim
120 10 15 20
e H
lin 3
Airflow Volume (m /minute)
100 L it M
m
Li
ne
80 it li External static pressure 120Pa, 30Pa
Lim
60 L
180
40 160
External static pressure (Pa)
ne
20 Limit li 140 H
M
0 120
e
10 15 20
lin
it
Airflow Volume (m3/minute)
m
100
Li
L
80
External static pressure 140Pa, 70Pa
60 e
180 e H it lin
it lin M Lim
H 40 Lim
160 L
20
External static pressure (Pa)
140 M
ine
A
it l
0
Lim
120 10 15 20
Airflow Volume (m3/minute)
100 ne
L i t li H
Lim M
80 External static pressure 110Pa, 10Pa
e
it lin
60 Lim 180
L
40 160
External static pressure (Pa)
20 140
H
0 Limit line 120 M
10 15 20
e
lin
80 L
60
lin e
40
H Limit
lin e
Limit
20 M
L
0
10 15 20
Airflow Volume (m3/minute)
1-11-1-2-21
Indoor Units Type 6071 (60, 71) External static pressure 130Pa, 50Pa 1
180
U-60 U-71 U-125
160
S-6071 S-6071 S-6071 S-6071
H
ne
i
S-6071 S-6071
it l
Lim
100
80
Indoor Fan Performance L
H n e
60 it li
PQ diagram (Fig. 1-11-1-2-2) e Lim
lin
40 Limit M
External static pressure 150Pa, 90Pa L
20
180
H 0
160 15 20 25 30
Airflow Volume (m3/minute)
External static pressure (Pa)
140
ne
M
it li
Lim
L M 160
m
80 in e
Li
mit l
i
External static pressure (Pa)
L 140
60 H
L
120
in e
40 M
it l
L im
100
20 ne
Limit li
80
0
15 20 25 30 L
60
Airflow Volume (m3/minute)
e
40 e it lin
it lin Li m
External static pressure 140Pa, 70Pa Lim H
20 L M
180
A
160 0
H 15 20 25 30
Airflow Volume (m3/minute)
External static pressure (Pa)
140
M
ine
100 180
e
lin H 160
80 L it
m
Li M
line
External static pressure (Pa)
it 140
60 Lim
H
40 L 120
ne
100 M
i
it l
20
Li m
0 Limit line 80
15 20 25 30 L
Airflow Volume (m3/minute) 60
e
40 it lin
Lim
20 Limit line H
L M
0
15 20 25 30
Airflow Volume (m3/minute)
1-11-1-2-22
1 Indoor Units Type 1014 (100) External static pressure 130Pa, 40Pa
180
U-100
160
S-1014
e
lin
it
m
120
Li
Indoor Fan Performance
100
PQ diagram (Fig. 1-11-1-2-2) M
ine
80 mit l
External static pressure 150Pa, 90Pa Li
60 L
180
H
160 H 40
t line M
Limi
20 L
External static pressure (Pa)
140 A
Limit lin e
e
0
lin
120
20 25 30 35 40
it
m
M in e
Li
20 140
H
0 120
e
20 25 30 35 40 lin
100 it
Airflow Volume (m3/minute) m
Li
M
80
ne
External static pressure 140Pa, 70Pa it li
60 Lim
180 L
160 40 H
H line
Limit M
External static pressure (Pa)
140 20 L
Limit line
e
lin
0
it
120
m
20 25 30 35 40
Li
20 140
120 H
0 e
20 25 30 35 40 lin
100 it
m
Airflow Volume (m3/minute) Li
80 M
n e
60 it li
L L im
40
20 e
Limit lin M
H
L
0
20 25 30 35 40
Airflow Volume (m3/minute)
Indoor Units Type 1014 (125) External static pressure 130Pa, 50Pa 1
180
U-125
160
S-1014
H
120
Indoor Fan Performance e M
100 lin
PQ diagram (Fig. 1-11-1-2-2) it
m
Li
80 ne
mit li
External static pressure 150Pa, 90Pa L Li
60 H
180
e
H 40 it lin
160 Lim M
L
20 A
Limit line
External static pressure (Pa)
140
0
e
lin
120 M 20 25 30 35 40
it
m
100
mit l
ne H Li
i t li
80 L Lim M External static pressure 120Pa, 30Pa
60 180
e
L it lin
40 Lim External static pressure (Pa)
160
20 140
H
0 120 e
20 25 30 35 40 lin
it
3 m
Airflow Volume (m /minute) 100 Li M
80
ne
External static pressure 140Pa, 70Pa it li
60 L Li m
180
40 H
160 t line M
H Limi
20 L
External static pressure (Pa)
140
e
lin
0 Limit line
it
120
m
Li
M 20 25 30 35 40
100 Airflow Volume (m3/minute)
i ne
it l
80 ine
H Lim
L mit l External static pressure 110Pa, 10Pa
Li
60 M 180
40 L 160
lin e
Limit
External static pressure (Pa)
20 140
0 H
120
20 25 30 35 40
Airflow Volume (m3/minute) 100
M
e
80 lin
it
Li m
n e
60 L it li
Lim
40
e H
20 Limit lin M
L
0
20 25 30 35 40
Airflow Volume (m3/minute)
1-11-1-2-24
1 Indoor Units Type 1014 (140) External static pressure 130Pa, 50Pa
180
U-140
160
S-1014 H
120 e
lin M
Indoor Fan Performance it
m
100 Li
PQ diagram (Fig. 1-11-1-2-2) ne
80 mit li
Li
L n e
External static pressure 150Pa, 90Pa it li
60 Lim H
180
M
H 40
160 L
20 A
External static pressure (Pa)
140
M Limit lin e
0
120 25 30 35 40
e
lin
100
m
e m
lin Li
Li
it M
80 L Lim
External static pressure 120Pa, 30Pa
60 180
L
t line
40 Limi External static pressure (Pa)
160
20 140 H
0 120
25 30 35 40
e M
Airflow Volume (m3/minute) 100 lin
it
Li m
n e
80 it li
External static pressure 140Pa, 70Pa L Lim
60
180
40 H
160 line M
H Limit
20 L
External static pressure (Pa)
140
M 0 Limit line
120 25 30 35 40
e
lin Airflow Volume (m3/minute)
100 it ine
Lim mit l
H Li
ine
80 L
mit l External static pressure 110Pa, 10Pa
Li M
60 180
40 L 160
lin e
Limit
External static pressure (Pa)
20 140
0 H
120
25 30 35 40
Airflow Volume (m3/minute) 100 M
ine
mit l
80 Li
e
60 L it lin
Lim
40
H
20 Limit lin e M
L
0
25 30 35 40
Airflow Volume (m3/minute)