Professional Documents
Culture Documents
FAGOR Innovation 8kg
FAGOR Innovation 8kg
Date: 25/02/2008
Document No.: 14538
t e c h n i c a l
This document is intended for all persons rendering technical support services (T.S.S.).
It is designed to facilitate the repair of the product described. It provides documentary
support for technical consultations.
This manual contains notes warning about safety issues:
!
Warning: This identifies information or circumstances
that may cause personal injuries or death.
I
I Important: This identifies information that is critical for
a correct understanding of the product.
© Copyright by Fagor Electrodomésticos S.Coop. 2008. All rights reserved. The total
or partial reproduction of this document, by any procedure and on any type of media,
is prohibited without written authorisation from the holder of the usage rights. Breach
of this copyright will be pursued in conformity with applicable legislation and may lead
to criminal charges.
FAGOR ELECTRODOMESTICOS reserves the right to introduce, without prior
notification, any modifications to the characteristics of its manufactured products.
t e c h n i c a l
Table of contents
In order to avoid fire risk, electric shock, personal injury or other injuries when
using the washing machine, take the following precautions:
This washing machine is supplied with a manual that contains instructions on
operation, maintenance and installation. Read all the instructions before using the
washing machine.
Do not wash articles which have been previously cleaned, washed, soaked or treated
with gasoline, dry-cleaning solvents or other inflammable or explosive substances as
they produce vapours that may ignite or explode.
Do not add gasoline, dry-cleaning solvents or other inflammable or explosive substances
to the wash water since they produce vapours which may ignite or explode.
Do not repair or replace any part of the washer, nor attempt any type of service unless
it has been recommended in the manual’s maintenance instructions..
Do not stand or sit on the machine, or lean on the open loading door.
To reduce the risk of fire or electric shock, do NOT use an extension lead or adapter
to connect the washing machine to the mains electricity.
The machine must only be used for what it was designed.
Follow the washing instructions recommended by the manufacturer of the item to
be washed.
Do not start the washing machine until you have made sure that:
• It has been installed according to the installation instructions.
• All of the water connections, drainage, electricity and earthing comply with
local regulations and/or other applicable regulations.
t e c h n i c a l
0905014763080200001
Year of manufacture
REGISTRATION PLATE
MAKE AND MODEL TYPE OF APPLIANCE
t e c h n i c a l
Features
2.- Features
This range comprises of the following models:
Additional
Drawer for Button Programme Start/pause Spin + flot Time delay
functions
detergent ON/OFF selector button button button
button
Stop
1000
3h 6h 9h
700
400
AA
+
8 kg Select
Wash programmes
For washing machines manufactured after 1st of May 2007
PROGRAMMES V1 circuits
NORMAL DELICATE FABRICS SPECIAL
1 Normal cold 7 Delicate Mixed 40ºC 10 Antibacterial 90ºC
2 Fast 30ºC 8 Delicate cold 11 Eiderdown 30ºC
3 Normal 30ºC 9 Delicate 30ºC 12 Curtains 30ºC
4 Normal 40ºC 13 Hand wash
5 Normal 60ºC 14 Quick (15 minutes)
6 Pre-wash 60ºC 15 Rinses
16 Spin
LB6W302A1 Circuit
t e c h n i c a l
Description of operation
Spin
The wash options must always be selected after selecting the wash programme.
Any change to the programme carried out during
the selection cancels the options which were 1000
Stop
previously selected.
3h 6h 9h
700
400
turns on.
b) To change the speed, press the spin button 1000
Stop
3h 6h 9h
repeatedly, and the appropriate pilot light will 700
light up. 400
400
Select
Select
400
programme. To select the time delay in hours,
choose 3, 6 or 9 hours.
Cancel time delay Select
To cancel the delay, press the time delay button until the pilots indicating the delay
go off. Changing to another programme also cancels the delay.
Start
a
Start/Pause button
a) To start the washing machine you must press the
start/stop key.
t e c h n i c a l
Description of operation
Additional functions
Button for selecting additional functions according to programmes.
There are 2 options: anti-crease and intensive wash.
Stop
1000
Press the button to display the required option. 700
3h 6h 9h
400
By pressing several times, you can choose
between various combinations of one or two
additional functions at the same time, depending
on the chosen programme.
Select
Key: Anti-crease
This stops at the final rinse, leaving the clothing floating in water. When the function is
deactivated, the washer continues the programme, draining and spinning.
This is used when you are not at home, for example, to delay the spin until you have
arrived so that creases are not caused by the clothes being spun and then left in
the drum.
Key: Intensive Wash
This option, specially recommended for very dirty or stained garments, gives better
results by lengthening the wash cycle.
Programme progress
When the programme is running, the pilot lights indicate the
a current programme phase.
400
Important: If, during the wash cycle, the programme is changed using the selector,
the washer is left in the PAUSE state, and the programme is canceled. To add or
remove an article, press the start/pause button and make sure that the water is not
above the door overflow level, and that the interior temperature is not high. Press the
start/pause button again to re-start the washer from the same phase of the cycle in
which it was stopped.
t e c h n i c a l
Description of operation
Power failure
When the supply returns after a power failure, the washer continues to work as normal,
from the point at which it stopped (its memory lasts a few hours).
The same thing happens if the ON/OFF button is pressed.
Warnings
To reduce the noise level of the spin cycle: use the adjustable feet to level the washer.
Aim to wash clothes of different sizes in the same wash programme, for a better
weight distribution in the drum when spinning.
All the models have a spin cycle safety system, which prevents them spinning if the
distribution of the clothes in the drum is very uneven. This prevents excessive vibration.
If at any time the clothes have not been correctly spun, spread them out more evenly
in the drum, and spin again.
t e c h n i c a l
Description of operation
4'
1400 RPM 2 with variable spin, Stator resistance: 3.3 Ω
34!4/2
and makes rotating Rotor resistance: 2.46 Ω
movements when Tachogenerator resistance:
washing and spinning. 90 Ω
Motor power supply:
- Clockwise, power
220 V, contacts 4
and 5. Bridge between
contacts 3 and 6.
4(%2-!,
02/4%#4/2
- Anti-clockwise, power
2 4(%2-!,
34!4/2 4' 220 V, contacts 4
and 6. Bridge between
02/4%#4/2
contacts 5 and 3.
2 34!4/2 4'
t e c h n i c a l
Description of operation
t e c h n i c a l
Description of operation
t e c h n i c a l
Description of operation
Stop
1000
3h 6h 9h
700
400
AA
+
8 kg Select
10
t e c h n i c a l
Description of operation
Stop
1000
3h 6h 9h
700
400
AA
+
8 kg Select
11
T.S.S. programme fast forward function: Press the start / pause button to move to another step in the programme without first having to finish the step.
t e c h n i c a l
FILLING EV activated for 8 min The machine stops with the door lock activated All options are reset if:
and without water 1.- Power is lost (unplugged or ON/OFF)
Wash and rinse LEDs flashing 2.- Selector position is changed
3.- If, when the programme finishes, the start button is
pressed
DOOR OPEN - Washing machines with instant-opening door lock: IN USER PROGRAMME All options are reset if:
At the beginning of the programme, the circuit detects that the door is not closed STOP (Programme end) 1.- Power is lost (unplugged or ON/OFF)
2.- Selector position is changed
- Washing machines with PTC door lock: 3.- Door is closed
If the door lock is without power for
8 seconds the fault is displayed (IF THE CIRCUIT IS IN A SPECIAL PROGRAMME
Wash and STOP LEDs flashing, alternating (AP_01, AP_01, REP_01 OR SAT) IN RESET IT
RETURNS TO STATUS A)
EMPTYING EB ON 6min. STOP (Programme end) All options are reset if:
and PN ON (full). Rinse and STOP LEDs flashing 1.- Power is lost (unplugged or ON/OFF)
Fault modes description table
12
Wash, rinse, STOP and intensive wash LEDs flashing
NTC NTC in short circuit or open circuit The programme ends without heating the water
Wash, rinse, STOP and spin LEDs flashing
MOTOR Tachogenerator failure, motor blocked STOP (Programme end) The same as the previous ones but with the door lock
- The wash programme is stopped for 120 seconds activated
- The error counter starts counting Door lock always activated
- If the error counter counts 3 faults, the error code F08 is displayed
- When the stop time is exceeded, the programme begins again
If the error does not occur in the next 20 seconds the error counter is reset. The
programme stops (in any instance) and starts again in the same position. If the error
occurs in the spin phase the programme will start the whole spin sequence again from
the start.
This error returns to the initial conditions if the error is reset.
Wash, rinse, STOP and Flot LEDs flashing.
MOTOR The drum rotation direction does not change until the motor stops
INVERSION (max. time 2 min.)
FAULT Wash, rinse, STOP and extra intensive rinse LEDs flashing
UNBALANCED If an imbalance is detected when it makes 18 attempts to spin or during 15 minutes The washing machine spins at the lowest The fault is reset in the following way:
of attempts revolution 1.- Cutting off the power (unplugged or ON/OFF)
Wash and rinse LEDs flashing and STOP alternating 2.- Change selector position
Description of operation
VERY DELICATE SPIN SEMI-DELICATE SPIN DELICATE SPIN SUPER SPIN SPIN PLUS
t e c h n i c a l
SEC. ANTI-CLOCKWISE
NON-DETECTION
OF OVERFLOW AREA
13
SEC. SEC.
3.1.4.- Washing machine vibrations
SEC.
EXTRA SPIN
SEC.
Description of operation
t e c h n i c a l
Easy iron
• Spin vibrations
EASY IRON PHASE 0 EASY IRON PHASE 1 EASY IRON PHASE 2 EASY IRON PHASE 3
14
IMBALANCE TEST 1 and 2 IMBALANCE TEST 1 and 2 IMBALANCE TEST IMBALANCE TEST
Description of operation
MACHINE MODEL
t e c h n i c a l
Step 7
Normal spin:
Step 6
Step 5
15
Step 4
IMBALANCE TEST 1, 2, 3
Step 3
Step 2
Step 1
Step 0
SEC.
According to programme
Description of operation
t e c h n i c a l
Description of operation
16
t e c h n i c a l
Description of operation
17
t e c h n i c a l
Description of operation
E.V.1 PRE-WASH
E.V.2 WASH
PRESSURE SWITCH
FILTER
RESISTANCE
FUSE
AMA–GREEN
DRAIN
PUMP
MOTOR
18
© FAGOR ELECTRODOMESTICOS, S.COOP. 2008
Bº San Andrés, s/n
20500 Mondragón (Gipuzkoa)
España (Spain)