Professional Documents
Culture Documents
Littelfuse 05182021 Thyristor ljxx06xx qjxx06xhx d-2326834
Littelfuse 05182021 Thyristor ljxx06xx qjxx06xhx d-2326834
Littelfuse 05182021 Thyristor ljxx06xx qjxx06xhx d-2326834
RoHS
Description
This 6 A High Temperature Alternistor Triac solid state switch
series is designed for AC switching and phase control applications
such as motor speed and temperature modulation controls, lighting
controls, and static switching relays.
Sensitive type components guarantee gate control in Quadrants I
& IV as needed for digital control circuitry.
Alternistor type components only operate in quadrants I, II, & III
and are used in circuits requiring high dv/dt capability.
Standard type devices normally operate in Quadrants I & III
triggered from AC line
MT2 MT1
600V 700 V
VDSM/VRSM Peak non-repetitive blocking voltage PW=100 μs
800V 1000 V
QJxx06VHy/QJxx06DHy TC = 130°C
IT(RMS) RMS on-state current (full sine wave) QJxx06LHy TC = 125°C 6 A
QJxx06RHy/QJxx06NHy TC = 140°C
QJxx06VHy/QJxx06DHy 60
Non repetitive surge peak on-state f = 50 Hz t = 20 ms
QJxx06LHy/QJxx06RHy/QJxx06NHy 65
ITSM current A
(full cycle, TJ initial = 25°C) QJxx06VHy/QJxx06DHy 72
f = 60 Hz t = 16.7 ms
QJxx06LHy/QJxx06RHy/QJxx06NHy 80
QJxx06VHy/QJxx06DHy 21.5
I 2t I2t Value for fusing tp = 8.3 ms A 2s
QJxx06LHy/QJxx06RHy/QJxx06NHy 26.6
di/dt Critical rate of rise of on-state current f = 60 Hz TJ = 150°C 70 A/μs
IGTM Peak gate trigger current tp=20μs TJ = 150°C 4 A
PG(AV) Average gate power dissipation TJ = 150°C 0.5 W
Tstg Storage temperature range -40 to 150 °C
TJ Operating junction temperature range -40 to 150 °C
Note: xx=voltage/10, x = sensitivity
Electrical Characteristics (TJ = 25°C, unless otherwise specified) — Sensitive Triac (4 Quadrants)
Value
Symbol Test Conditions Quadrant Unit
LJxx06x8
I – II – III 10
IGT MAX. mA
VD = 12V RL = 60 Ω IV 20
VGT ALL MAX. 1.2 V
VGD VD = VDRM RL = 3.3 kΩ TJ = 150°C ALL MIN. 0.15 V
IH IT = 100mA MAX. 25 mA
400V 80
dv/dt VD = VDRM Gate Open TJ = 150°C TYP. V/μs
600V 50
(dv/dt)c (di/dt)c = 3.2 A/ms TJ = 150°C TYP. 2 V/μs
tgt IG = 2 x IGT PW = 15µs IT = 8.5 A(pk) TYP. 12 μs
Note: xx=voltage/10, x = package
Electrical Characteristics (TJ = 25°C, unless otherwise specified) — Alternistor Triac (3 Quadrants)
Value
Symbol Test Conditions Quadrant Unit
QJxx06xH2 QJxx06xH3 QJxx06xH4
IGT I – II – III MAX. 10 20 35 mA
VD = 12V RL = 60 Ω
VGT I – II – III MAX. 1.3 V
VGD VD = VDRM RL = 3.3 kΩ TJ = 150°C I – II – III MIN. 0.15 V
IH IT = 100mA MAX. 25 30 35 mA
400V 150 250 350
dv/dt VD = VDRM Gate Open TJ = 150°C QJxx06xHy MIN. 600V 100 200 250 V/μs
800V - - 450
(dv/dt)c (di/dt)c = 3.2 A/ms TJ = 150°C MIN. 15 18 20 V/μs
tgt IG = 2 x IGT PW = 15µs IT = 8.5 A(pk) TYP. 10 10 10 μs
Note: xx=voltage/10, x = package
Value
Symbol Test Conditions Quadrant Unit
QJxx06xH2
I – II – III 50
IGT MAX. mA
VD = 12V RL = 60 Ω IV 50
VGT ALL MAX. 1.3 V
VGD VD = VDRM RL = 3.3 kΩ TJ = 150°C ALL MIN. 0.2 V
IH Initial IT = 100mA MAX. 50 mA
dv/dt VD = VDRM Gate Open TJ = 150°C 800V MIN. 1000 V/μs
(dv/dt)c (di/dt)c = 3.2 A/ms TJ = 150°C MIN. 4 V/μs
tgt IG = 2 x IGT PW = 15µs IT = 8.5 A(pk) TYP. 3 μs
Note: xx=voltage/10, x = package
Static Characteristics
Thermal Resistances
Symbol Parameter Value Unit
LJ/QJxx06Vyy
1.3
LJ/QJxx06Dyy
RƟ(JC) Junction to case (AC) QJxx06R5/QJxx06N5 0.9 °C/W
QJxx06L5 2.3
LJ/QJxx06Vyy
70
LJ/QJxx06Dyy
RƟ(J-A) Junction to ambient QJxx06R5 45 °C/W
QJxx06L5 90
Note: xx=voltage/10, y = sensitivity
Figure 1: Figure 2:
Definition of Quadrants Normalized DC Gate Trigger Current for
All Quadrants vs. Junction Temperature
ALL POLARITIES ARE REFERENCED TO MT1 1.8
MT2 POSITIVE
1.6
(Positive Half Cycle)
MT2 + MT2
1.4
IGT (TJ = 25°C)
(-) I GT (+) I GT
GATE GATE 1.2
IGT
REF REF
- QII QI
+ IGT
0.8
Ratio of
I GT
QIII QIV
MT2 MT2 0.6
REF
- 0
MT2 NEGATIVE REF -40 -15 10 35 60 85 110 135 150
(Negative Half Cycle)
NOTE: Alternistors will not operate in QIV
Junction Temperature (TJ)- ºC
Figure 3: Figure 4:
Normalized DC Holding Current Normalized DC Gate Trigger Voltage for
vs. Junction Temperature All Quadrants vs. Junction Temperature
1.6
1.6
1.4
1.2
VGT
1.0
IH
0.8
0.8
Ratio of
Ratio of
0.6
0.4 0.4
0.2
0
0
-40 -15 10 35 60 85 110 135 150
-40 -15 10 35 60 85 110 135 150
Figure 5: Figure 6:
Power Dissipation (Typical) Maximum Allowable Case Temperature
vs. RMS On-State Current vs. On-State Current
6 160 QJxx06RHy/QJxx06NHy
QJxx06RyQJxx06Ny
LJxx06Vy/LJxx06Dy
CURRENT WAVE FORM: Sinusoidal 150
5 QJxx06VHy/QJxx06DHy
LOAD: Resistive or Inductive
Power Dissipation (PD(AV)) - Watts
4
Maximum Allowable
130
QJxx06LHy/QJxx06Ly
3 120
110
2
CURRENT WAVE FORM: Sinusoidal
100
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 360°
CASE TEMPERATURE: Measured as shown
1 90 on Dimensional Drawing
80
0 0 2 4 6 8
0 1 2 3 4 5 6
RMS On-State Current (IT(RMS)) - Amps RMS On-State Current (IT(RMS)) - Amps
Figure 7:
On-State Current vs. On-State Voltage (Typical)
20
18
On-State Current (IT) - Amps
Positive or Instantaneous
16
14
12
10
0
0.6 0.8 1.0 1.2 1.4 1.6 1.8
Positive or Instantaneous
On-State Voltage (VT) - Volts
Figure 8:
Surge Peak On-State Current vs. Number of Cycles
100
10 Notes:
1. G
ate control may be lost during and immediately
following surge current interval.
2. O
verload may not be repeated until junction
temperature has returned to steady-state
rated value.
1
1 10 100 1000
Soldering Parameters
Reflow Condition Pb – Free assembly
- Temperature Min (Ts(min)) 150°C tP
TP
Pre Heat - Temperature Max (Ts(max)) 200°C
Ramp-up
Temperature
R
NON-ISOLATED
TAB
H 0.025 0.035 0.64 0.89
G
L J 0.195 0.205 4.95 5.21
H K 0.095 0.105 2.41 2.67
L 0.060 0.075 1.52 1.91
K N
M 0.085 0.095 2.16 2.41
J M
MT1 MT2 GATE Note: Maximum torque to N 0.018 0.024 0.46 0.61
be applied to mounting tab
is 8 in-lbs, (0.904 Nm).
O 0.178 0.188 4.52 4.78
P 0.045 0.060 1.14 1.52
R 0.038 0.048 0.97 1.22
2.03
.080
6.60
.260
Product Selector
Packing Options
DC
DC
XXXXXX
XXXXXX
(13.3)
XX
XX
XX
0.64 0.63
0.524 *
DC
DC
DC
(16.0)
XXXXXX
(16.3) XXXXXX
XXXXXX
XXXXXX
(13.3)
XX
XX
XX
Direction of Feed
* Cover tape 0.315
(8.0)
MT2
12.99
0.512 (13.0) Arbor (330.0)
Dimensions
TO-263 Embossed Carrier Reel Pack (RP)
HoleSpecifications
Dia.
are in inches
(and millimeters).
Meets all EIA-481-2 Standards
0.63 0.157
(16.0) 0.64
(4.0)
(16.3)
Gate
0.059
DIA
(1.5)
MT1
Direction of Feed
0.945
(24.0)
0.827
(21.0)
*
* Cover tape
MT2
12.99
(330.0)
0.512 (13.0) Arbor
Hole Dia. Dimensions
are in inches
(and millimeters).
1.01
(25.7)
Direction of Feed
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are
not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics.
© 2021 Littelfuse, Inc.
11 Specifications are subject to change without notice.
Revised: GD. 05/04/21
Mouser Electronics
Authorized Distributor
Littelfuse:
QJ8006RH4TP QJ8006L5TP QJ8006N5RP QJ8006N5TP QJ8006R5TP