Professional Documents
Culture Documents
Task Card Electrical LRU 001
Task Card Electrical LRU 001
Task Card Electrical LRU 001
628023105.docx
ID #1 001
ATA CHAPTER2 ATA 73 FUEL
TASK
FUEL HEAT VALVE NEW
CARD TITLE3 WIRE HARNESS
INSTALLATION
AIRCRAFT TYPE4 REGISTRATION5 SERIAL NUMBER6 WORK ORDER#7
B727 WSC-2022 2877 002
TOTAL AIRFRAME TIME 8
AIRFRAME CYCLES 9
ORIGINATED BY 10
DATE OPENED11
3259 hours 4031 cycles WS Aviation 10/dec/2021
MAINTENANCE REQUIRED / DEFECT DESCRIPTION12
(1)
a) Make sure the installation site of the new wiring is clean.
b) Make sure diagram E1 – Fuel heat valve control and adjacent circuit are in good conditions.
I. ___________________________________________________________________________________
II. ___________________________________________________________________________________
III. ___________________________________________________________________________________
IV. ___________________________________________________________________________________
V. ___________________________________________________________________________________
(2)
A. Install a new wire harness IAW Diagram E2, and modify the existing circuit when necessary.
Leak Check 27
Detailed on Task Card ID #
Other28
Detailed on Task Card ID #
MAINTENANCE RELEASE29
IC Required?30 Post Maintenance Inspection31 Task Card certified by (Signature & ACA)32:
Yes No Initial ACA
Independent Check (IC) accomplished before
Maintenance Release by (Signature & ACA):33
WSC Aviation
628023105.docx
Date34: dd/mmm/yyyy Time35: hh:mm
IC ONLY The described maintenance has been performed in accordance with the applicable
airworthiness requirements and is subject to the FOLLOW-ON MAINTENANCE
CHECKS detailed above. AMO# 2021-1436
Independent Check carried out satisfactory. AMO# 2021-14 SUBJECT TO SATISFACTORY TEST FLIGHT 37
Details of check(s) to be performed
TEST FLIGHT ONLY
during TEST FLIGHT38
1
END NOTES
2
1 Module letter. Judge to fill in.
Judge to fill in.
3
Name of module. Judge to fill in.
4
As per Host Country Aircraft logbook (filled in by competitor if logbook available).
5
As per Host Country Aircraft. Filled in by competitor.
6
As per Host Country Aircraft logbook (filled in by competitor if logbook available).
7
As designated by judge and must align with section 11 of Work Order Summary form 8.5.
8
As per Host Country Aircraft logbook (filled in by competitor if logbook available).
9
As per Host Country Aircraft logbook (filled in by competitor if logbook available).
10
Competitor to fill in.
11
Competitor to fill in current date.
12
Judge to fill in as per attached WSI procedure. Competitor to tick the box only.
13
Competitor to fill in after task completed.
14
Competitor to attach any supporting documents for deferral/resolution description.
15
Competitor to tick box, if applicable.
16
-
17
Competitor to tick applicable box.
18
Competitor to fill in as per section 7 of Technical Dispatch Report.
19
Competitor to fill in as per section 8 of Technical Dispatch Report.
20
Competitor to fill in current date and time.
21
-
22
-
23
-
24
-
25
-
26
Competitor to fill in and tick applicable box including Task Card ID#. Applies to overlapping Task
Cards only.
27
Competitor to fill in and tick applicable box including Task Card ID#. Applies to overlapping Task
Cards only.
28
Competitor to fill in and tick applicable box including Task Card ID#. Applies to overlapping Task
Cards only.
29
-
30
Competitor to tick box, if applicable.
31
Competitor to fill in only if any follow-on maintenance checks have been carried out as per section
21.
32
Competitor to complete when task has been resolved or deferred.
33
Competitor to complete only if “independent control check” has been carried out.
34
Competitor to fill in current date.
35
Competitor to fill in current time.
36
-
37
Competitor to tick box, if applicable.
38
Competitor to fill in only if Test Flight required.