Professional Documents
Culture Documents
HM150X01 101
HM150X01 101
HM150X01 101
TITLE : HM150X01-101
Product Specification
P0
REVISION HISTORY
REV. ECN NO. DESCRIPTION OF CHANGES DATE PREPARED
P0 - Initial Release 2013.12.24 Zhang Hongkun
Contents
No. Items Page
12.0 Label 21
1.0.1 Introduction
HM150X01-101 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 15.0 inch diagonally
measured active area with XGA resolutions (1024 horizontal by 768 vertical pixel array). Each
pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this
module can display 16,194,227 colors. The TFT-LCD panel used for this module is adapted for
a low reflection and higher color type.
Gate IC
TFT LCD Panel
1024 × 768
Source IC
1.0.2 Features
z LED back-light
z LED light bar replaceable
z LVDS interface
z RoHS Compliant
1.0.3 Application
z TFT-LCD Monitor
z Application
The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit. The operational and non-operational maximum voltage and current
values are listed in Table 2.
< Table 2. LCD Module Electrical Specifications > [Ta =25±2 ℃]
Note : 1) Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 ℃ max. and no condensation of water.
Relative Humidity
100
90
80 (40, 80)
60
Operating Range (50, 50)
40 (60, 27)
20 (70, 20)
Storage Range
5
Temperature (℃)
Values
Parameter Symbol Unit Notes
Min Typ Max
Power Supply Input Voltage VDD 3.0 3.3 3.6 V
Note 1
Power Supply Current IDD - 605 730 mA
LED Driver Power Supply
HVDD 10.8 12 12.6 V
Voltage
LED Driver Power Supply Note 2
IHVDD - 550 657 mA
Current
LED Driver Efficiency η - 81 - %
Positive-going Input
VIT+ - +100 mV
Threshold Voltage Vcom = 1.2V
Negative-going Input typ.
VIT- -100 - mV
Threshold Voltage
Differential input common VIH=100mV,
Vcom 1.2 V
mode voltage VIL=-100mV
PD - 2.0 2.5 W
Power Consumption PBL - 6.4 7.5 W
PTotal - 8.4 10.0 W
Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for 3.3V at 25 ℃
Max value at Black Pattern
2. The LED Life-time define as the estimated time to 50% degradation of initial
luminous.
Notes : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The
viewing angles are determined for the horizontal or 3, 9 o’clock direction and
the vertical or 6, 12 o’clock direction with respect to the optical axis which is
normal to the LCD surface (see FIGURE 1).
o
Field = 1
50 cm
TFT-LCD module LCD panel TFT-LCD module LCD panel
View angel range, uniformity, etc. measurement setup Flicker, measurement setup
Figure 2. White Luminance and Uniformity Measurement Locations (9 points)
Luminance of white is defined as luminance values of max 9 points across the LCD
surface. Luminance shall be measured with all pixels in the view field set first to
white. This measurement shall be taken at the locations shown in FIGURE 2 for a
total of the measurements per display.
The White luminance uniformity on LCD surface is then expressed as : ΔY9 =
Minimum Luminance of 9 points / Maximum Luminance of 9points (see FIGURE 2).
TR TF
100%
Optical
90%
Response
10%
0%
Time
The electro-optical response time measurements shall be made as shown in
FIGURE 3 by switching the “data” input signal ON and OFF. The times needed
for the luminance to change from 10% to 90% is Tr and 90% to 10% is Td.
Where:
YA = Initial luminance of measured area (cd/m2)
YB = Subsequent luminance of measured area (cd/m2)
The location measured will be exactly the same in both patterns
R G B R G B R G B R G B
1 Pixel = 3 Dots
R G B
R G B R G B R G B R G B
Value
Parameter Symbol Unit
Min. Typ. Max.
7.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS
Values
Parameter Units
Min Typ Max
T1 0 - 10 ms
T2 0 - 50 ms
T3 200 - - ms
T4 500 - - ms
T5 0 - 50 ms
T6 0 - 10 ms
T7 500 - - ms
Notes:
1. When the power supply VDD is 0V, keep the level of input signals on
the low or keep high impedance.
2. Do not keep the interface signal high impedance when power is on.
Back Light must be turn on after power for logic and interface signal
are valid.
9.0.2 Mounting
There shall not be obvious light from the back-lighting system around the edges of the
screen as seen from a distance 50cm from the screen with an overhead light level of 150lux.
Gravity 50G
12.0 LABEL
(1) Product label
HM150X01-101
1 2 3 4 5 6 7
X X X X X X 1 0 0 X X X X X X X X
Label 2
Label 1
Pin
1~5
Pin
1~20