Professional Documents
Culture Documents
01-02 Specifications Rev. 0-18-18
01-02 Specifications Rev. 0-18-18
Loader Backhoe
590ST
Tier 4B Final
Model Specifications
URSO F. 01/2018
Model Specification CASE T-Series TLB Tier 4B Final
695ST
580ST
1
Model Specification CASE T-Series TLB Tier 4B Final
Contents
580ST-590ST
Model Specification CASE T-Series TLB Tier 4B Final
General Specifications
3
Model Specification CASE T-Series TLB Tier 4B Final
4
Model Specification CASE T-Series TLB Tier 4B Final
5
Model Specification CASE T-Series TLB Tier 4B Final
6
Component identification 580ST-590ST
Model Specification CASE T-Series TLB Tier 4B Final
7
Component identification 695ST
Model Specification CASE T-Series TLB Tier 4B Final
NOTE: Boom with overlapping cylinder boom* available as a standard option on most model
configurations.
8
Model Specification CASE T-Series TLB Tier 4B Final
FORWARD CONTROL
Steering column
The machine is equipped with a hydrostatic power steer-
ing, which considerably reduces the effort necessary to
turn the steering wheel (1). Familiarize yourself with the
effort required to turn the wheel before driving the ma-
chine for the first time.
9
Model Specification CASE T-Series TLB Tier 4B Final
10
Model Specification CASE T-Series TLB Tier 4B Final
1. When the operator is about to start working with the backhoe attachment in conditions
which could cause the machine to roll over, the operator must activate the roll-over
protection device by pressing the switch (ON position and lamp turned on).
2. Press the switch again to disengage the roll-over protection feature (control lamp OFF).
NOTE: When the switch is ON, the audible alarm will sound by means of the buzzer
when the pres- sure switch, installed on the backhoe attachment boom cylinder, detects a
pressure exceeding 140 bar (2030 psi).
(7) Glide Ride™ switch (optional on 2WD models) orAuto-Glide Ride™ switch (Optional on 4WD
models)
Ride Control™
The Ride Control™ system control improves the machine comfort during travel, regardless of a full or
empty bucket over any type of terrain.
It reduces forward and rearward pitching when moving rearwards or forwards and when carrying loads,
at the same time increasing productivity and operator comfort.
It also reduces impact forces to the machine during operation. Do not use this system while operating
the loader attachment.
11
Model Specification CASE T-Series TLB Tier 4B Final
Auto-Ride Control™
The Auto-Ride Control™ system control improves the machine comfort during travel, regardless of
a full or empty bucket over any type of terrain.
It reduces forward and rearward pitching when moving rearwards or forwards and when carrying loads,
at the same time increasing productivity and operator comfort.
It also reduces impact forces to the machine during operation. Do not use this system while operating
the loader attachment.
1. Press the emblem to turn ON the hazard lights(control lamp off). Turn signal lights will
continuously flash ON and OFF.
2. Press the emblem again to turn OFF the hazard lights (control lamp off).
12
Model Specification CASE T-Series TLB Tier 4B Final
13
Model Specification CASE T-Series TLB Tier 4B Final
Position A: Road
NOTICE: Before undertaking any road travel, select “Road” mode and fold back the cover to lock the
switch in this position.
Position B: Four-Wheel Steer (4WS)
1. When the operator is about to start working with the backhoe attachment in conditions
which could cause the machine to roll over, the operator must activate the roll-over
protection device by pressing the switch (ON position and lamp turned on).
2. Press the switch again to disengage the roll-over protection feature (control lamp OFF).
NOTE: When the switch is ON, the audible alarm will sound by means of the buzzer
when the pres- sure switch, installed on the backhoe attachment boom cylinder, detects a
pressure exceeding 140 bar (2030 psi).
(7) Glide Ride™ switch (optional on 2WD models) orAuto-Glide Ride™ switch (Optional on
4WD models)
Ride Control™
The Ride Control™ system control improves the machine comfort during travel, regardless of a full or
empty bucket over any type of terrain.
It reduces forward and rearward pitching when moving rearwards or forwards and when carrying loads,
at the same time increasing productivity and operator comfort.
It also reduces impact forces to the machine during operation. Do not use this system while operating
the loader attachment.
14
Model Specification CASE T-Series TLB Tier 4B Final
Auto-Ride Control™
The Auto-Ride Control™ system control improves the machine comfort during travel, regardless of
a full or empty bucket over any type of terrain.
It reduces forward and rearward pitching when moving rearwards or forwards and when carrying loads, at the same
time increasing productivity and operator comfort.
It also reduces impact forces to the machine during operation. Do not use this system while operating the loader
attachment.
• In situations where manual gearshifting (up or downshift) is required, the automatic gearshift
of the powershift transmission can be overridden with this switch.
• When the manual mode is no longer required, place the switch back to the OFF position to
return to automatic gearshifting.
1. Press the emblem to turn ON the hazard lights(control lamp off). Turn signal lights will
continuously flash ON and OFF.
2. Press the emblem again to turn OFF the hazard lights (control lamp off).
15
Model Specification CASE T-Series TLB Tier 4B Final
Start.
NOTE: This key can be used to lock the cab doors, the
engine guard and the fuel tank plug.
Hand throttle
16
Model Specification CASE T-Series TLB Tier 4B Final
Lever for direction indicators, main beams, front windshield wiper and
washer (cab)
Position 0: Neutral.
0 = Stop
I = Normal speed
17
Model Specification CASE T-Series TLB Tier 4B Final
18
Model Specification CASE T-Series TLB Tier 4B Final
7. Menu scrolling switch: With this switch, it is possible to scroll through the menu or data options
shown on the diagnostic display.
8. Menu enter switch: With this control it is possible to display and confirm the menu options shown
on the display.
9. Rear windshield wiper and washer switch: This switch has three positions:
• The first position is OFF (lamp off) and both the windshield wiper and the windshield
washer are disabled.
• The second position allows to press the symbol side of the switch to activate the rear
windshield wiper (lamp on).
• The third position, allows to press the symbol side of the switch and hold to activate the
windshield washer (lamp on). When releasing the switch, the windshield washer stops and the
windshield wiper starts moving.
19
Model Specification CASE T-Series TLB Tier 4B Final
• Press on the 2 switches to unlock (retract pins) of quick coupler on backhoe attachment.
• Press on the 2 switches to lock (extend pins) of quick coupler on backhoe attachment.
13. Backhoe attachment side shift carriage locking switch (Side shift version)
It allows locking (control lamp on) or unlocking (control lamp off) the sliding carriage the backhoe
attachment is mounted on
20
Model Specification CASE T-Series TLB Tier 4B Final
21
Model Specification CASE T-Series TLB Tier 4B Final
These control levers are used to operate the backhoe attachment. The speed of movement of each control
depends on the angle to which the lever is tilted. In the intermediate position, two movements can be
obtained simultaneously.
Four backhoe attachment control configurations exist, depending on the country concerned:
• Standard configuration
• ISO configuration
• Four lever pattern configuration
• Cross-pattern configuration
The operating pattern of the control levers is different. Check which configuration you have on your
machine.
22
Model Specification CASE T-Series TLB Tier 4B Final
Standard configuration
Position 0: Neutral/hold. This position enables the attachment movement to be stopped. As soon as
the lever is released, it automatically returns to the neutral position 0 and the attachment remains in
the position where it was when movement stopped.
Position 0: Neutral/hold. This position enables the attachment movement to be stopped. As soon as
the lever is released, it automatically returns to the neutral position 0 and the attachment remains in
the position where it was when movement stopped.
23
Model Specification CASE T-Series TLB Tier 4B Final
NOTE: The functions of the controls are the same for both the overlapping cylinder boom and the in-
line cylinder boom.
24
Model Specification CASE T-Series TLB Tier 4B Final
ISO configuration
25
Model Specification CASE T-Series TLB Tier 4B Final
NOTE: The function of the controls are the same for both thr overlapping cylinder boom and the in-line
cylinder
26
Model Specification CASE T-Series TLB Tier 4B Final
Position “0”: Neutral/hold. This position enables the attachment movement to be stopped. As soon
as the lever is released, it automatically returns to the neutral position “0” and the attachment
remains in the position where it was when movement stopped.
Position “A”: The backhoe dipper extends.
27
Model Specification CASE T-Series TLB Tier 4B Final
NOTE: The functions of the controls are the same for both the overlapping cylinder boom and the in-
line cylinder boom.
28
Model Specification CASE T-Series TLB Tier 4B Final
Cross-pattern configuration
Backhoe boom and backhoe attachment swing left-hand control lever
Position 0: Neutral/hold. This position enables the attach- ment movement to be stopped. As soon as the
lever is released, it automatically returns to the neutral position 0 and the attachment remains in the
position where it was when movement stopped.
Position 0: Neutral/hold. This position enables the attach- ment movement to be stopped. As soon as the
lever is released, it automatically returns to the neutral position 0 and the attachment remains in the
position where it was when movement stopped.
29
Model Specification CASE T-Series TLB Tier 4B Final
NOTE: The functions of the controls are the same for both the overlapping cylinder boom and the in-line
cylinder boom.
30
Model Specification CASE T-Series TLB Tier 4B Final
31
Model Specification CASE T-Series TLB Tier 4B Final
32
Model Specification CASE T-Series TLB Tier 4B Final
1. Control enable switch: With this switch in the ON (lamp on) position, all backhoe attachment
hydraulic controls are functional.
2. Left-hand hydraulic control lever: The left-hand hy- draulic control lever controls attachment
swing and the boom or the dipper (depending on the control pat- tern adopted).
3. Right-hand hydraulic control lever: The right-hand hydraulic control lever controls the bucket
and the boom or the dipper (depending on the control pattern adopted).
NOTE: The operating speed depends on the angle of movement of the control levers. In
intermediate position, two movements may be obtained simulta- neously.
4. Stabilizer controls: The right-hand control is for the right-hand stabilizer and the left-hand
control is for the left-hand stabilizer.
5. Control pattern change switch: This switch is used for changing the standard control pattern to
the ISO pattern.
6. Telescopic dipper controls (proportional controls): Press the right-hand button to extend the
telescopic dipper. Press the left-hand button to retract the telescopic dipper.
7. Wrist rests: The wrist rests may be adjusted to the required height.
8. Hydraulic control lever support angle adjustment: These controls are used for the fore/aft and
left/right adjustment of the arm.
9. Horn button (Momentary action control).
NOTE: Machines are not available with both Bi-direc- tional auxiliary controls and Uni-
directional auxiliary controls.
10. Controls of auxiliary bi-directional attachment (two button operation) (If fitted): Proportional
buttons for the activation of the additional attachment.
11. Controls of auxiliary uni-directional attachment (one button operation) (If fitted): Proportional
button for the activation of the additional attachment.
12. Decelerator button: By pressing this button, the en- gine rpm sets to low idle. During this phase,
the ac- celerator knob and pedal are disabled.
By pressing the button again, the engine rpm is re- stored and the accelerator knob and pedal are
func- tional again.
33
Model Specification CASE T-Series TLB Tier 4B Final
WARNING
Unexpected machine movement!
After using the attachment and before leav- ing the
machine, deactivate all the controls by moving the
control enable switch to the OFF position. 1 2
Failure to comply could result in death or se- rious
injury
34
Model Specification CASE T-Series TLB Tier 4B Final
35
Model Specification CASE T-Series TLB Tier 4B Final
36
Model Specification CASE T-Series TLB Tier 4B Final
37
Model Specification CASE T-Series TLB Tier 4B Final
Press and hold down the left-hand button (2) to retract the
telescopic dipper. As soon as the button is released the
dipper stops and remains in the position it occupied when the
button was released.
38
Model Specification CASE T-Series TLB Tier 4B Final
Press and hold the left-hand button (1) to let the oil flow
out of the left-hand side of the boom.
Press and hold the left-hand button (2) to let the oil flow
out of the right-hand side of the boom.
Once the adjustment has been carried out, tighten the two
knobs (2).
39
Model Specification CASE T-Series TLB Tier 4B Final
Stop plate
configuration
for CAT bucket
Stop plate
configuration
for CASE and
DEERE buckets
40