Professional Documents
Culture Documents
INS00032 ERBA LISAWASH-EN - C-TrugdZxGXy
INS00032 ERBA LISAWASH-EN - C-TrugdZxGXy
INS00032 ERBA LISAWASH-EN - C-TrugdZxGXy
for
Erba LisaWash
MICROPLATE WASHER
INS00032
Table of Contents
1. Overview ............................................................................................................3
3. Installation .........................................................................................................6
4. Operation ...........................................................................................................9
4.1 Power-on............................................................................................................. 9
4.2 Operation Procedures ......................................................................................... 9
4.3 Shutdown .......................................................................................................... 10
4.4 Precautions: ...................................................................................................... 11
6. Troubleshooting ..............................................................................................13
7. Warning ............................................................................................................14
8. Contact .............................................................................................................15
2
Erba LisaWash, User Manual
1. Overview
1.1 System structure
The appearance of the Erba Lisawash Elisa Washer is as shown in figure 1:
(5)
(6)
(2)
(1)
(3)
(4)
Figure 1
The system consists of pumps, controlling mechanism, wash head, plate tray, circuit,
and bottles. The pumps include a water pump for transporting detergent to wash head
and
a vacuum pump for evacuating the waste from the ELISA plate. The controlling mecha-
mech
nism is primarily used to control the up/down and left/right movement of wash head.
Wash head is available in 8 or 12 way manifold for 8×12 and 12×8 plates respectively.
The circuit is an advanced single chip system
stem composed of high speed CPU.
The Erba Lisawash Elisa Washer is equipped with a touch screen, which makes oper-
ope
3
Erba LisaWash, User Manual
4
Erba LisaWash, User Manual
Operating Environment
5
Erba LisaWash, User Manual
3. Installation
3.1 Unpacking
Upon opening the package, check the main unit and accessories against the packing list.
If you find anything damaged or missing, please contact your supplier immediately.
3.4 Connection
3.4.1 Connect the air pump tube (blue) on the waste bottle to the Air Pump port (blue) on
the back of the device, as shown in figure 2.
6
Erba LisaWash, User Manual
Figure 2
(1) Power switch (2) Air Pump port (3) Vent port
(4) Waste port (5) Detergent port (6) Duct hole
(7) Valve (8) Grounding (9) Water Pump
(10) Overflow Sensor plug (11) Power socket
3.4.2 Connect the waste tube (green) on the waste bottle to the Waste port (green) on
the back of the device.
3.4.3 Connect the tube (yellow) on the wash bottle to the Wash port (yellow) on the back
of the device.
3.4.4 Put the duct next to the valve into the round hole of the valve by pressing the valve
core on the top of the valve.
3.4.6 Insert the two-wire cord (water pump supply lead) on the detergent bottle into the
Water Pump port on the back of the system.
3.4.7 Connect a proper ground wire to the Grounding on the back of the system.
7
Erba LisaWash, User Manual
3.4.8 Set the Power switch to off (O). Then insert the power cord into the Power socket
on the back of the device and switch on the power.
3.4.9 Unscrew the wash bottle cap (hold the cap with your left hand and rotate the bottle
clockwise with your right hand) and add sufficient detergent, then tighten the cap.
NOTE: When fixing the bottle cap, check if the white O-ring in the cap is
damaged or placed correctly.
3.4.12 Position the plate tray on the four poles, in the front base of the device, and push
it into its place.
3.4.13 Fix the 8-head (or 12-head) wash head on the wash arm. Sleeve the thinner tube
of the wash arm on the inlet port of the wash head and the thicker one on the outlet port.
8
Erba LisaWash, User Manual
4. Operation
4.1 Power-on
Switch on the system, it starts initialization and then the Main Menu is displayed on the
screen.
Main Menu
Plate Settings Program Settings
System Settings Wash Program
4.3 Shutdown
When the system is not used, the buffer salt in the detergent may be solidified, this
blocking the wash head. To avoid this situation, perform the distilled water prime.
4.4 Precautions:
4.4.1 Empty the waste bottle regularly.
4.4.2 Before starting the ELISA wash, check if the No. of heads of the installed wash
head is in accordance with the settings. If you only want to wash part of the plate, please
select corresponding No. of rows.
4.4.3 The selected type of plate should be consistent with the one you are using.
4.4.4 It is strongly recommended to run wash program #41 for 2 times after the daily
work.
11
Erba LisaWash, User Manual
5.6 Storage
The device should be stored in a room with good ventilation and relative humidity no
greater than 80% and without corrosive gas.
12
Erba LisaWash, User Manual
6. Troubleshooting
Symptoms Causes Actions to be taken
No response when pow- 1. The 220V power supply is abnormal Restore the normal power supply
ering on the device 2. The fuse is broken Replace the fuse
The fuse is broken again 1. Power supply is greater than 242V Restore the normal power supply
after being replaced 2. The device goes wrong Contact local distributor
No detergent is dispensed 1. The plug of the water pump is not Insert it again properly
inserted in place
2. The position of the water pump is Change the position of the water
not good, it blocks the duct pump
3. The duct cannot be restored Refer to 5.2
4. The duct is broken Replace the duct
Can’t aspirate 1. The tube is leaking The tube is broken or connection is
2. The waste bottle is leaking loose
3. The probe on wash head is blocked Check if the bottle cap is broken or
tightened
Unclog the probe with the needle
The wash head moves 1.The moving part is blocked Clean the moving part and remove
up/down or left/right ab- 2. The system goes wrong the barrier
normally Contact local distributor
“Waste Overflow” is dis- 1. The plug of the overflow sensor is Insert the plug again properly
played when the waste loose
bottle is not full 2. The overflow sensor is defective Replace the overflow sensor
Liquid drops at duct tube 1. The connections from duct tube or Tighten the tubes or change it if
or aspirate tube aspirate tube to wash head is loose or necessary
leaking
2. The tubing system is leaking Check the tubing system
3. The duct tube is distortion Replace the duct tube
High residual volume 1. The ELISA plate is not placed well Place the plate again
2. The Aspirate Height value is not Change the Aspirate Height value
correct and make sure the probes can reach
the well bottom
3. The Start Pos. Setting is not good Change the Start Pos. Setting and
make sure the probe can reach the
center of the wells
13
Erba LisaWash, User Manual
7. Warning
Erba Lisawash is a compact in vitro diagnosis instrument. It may bring risks to the pa-
tients indirectly, and accompanying risks to the operator and environment. To avoid
these risks, be sure to read the following instructions carefully.
7.1. This device adopts AC 220V/110V which may bring electrical harm to
human body. Don’t open the rear cover before switching off the power
supply. If you need to open the rear cover to repair the device, contact our service per-
sonnel or professionals.
7.2. Since the patient samples may contain germs or virus which will cause
disease, be sure to dispose of the waste in accordance with relevant
regulations of your hospital. Transport and store the patient samples and
handle the sample tubes strictly as instructed in relevant regulations of your hospital.
7.3. Don’t operate the device unless you have read this Operation Manual
carefully.
USED SYMBOLS
Temperature limit
Manufacturer
Catalogue Number
Serial number
Use-by date
Date of manufacture
14
Erba LisaWash, User Manual
8. Contact
For customer and technical support:
Manufacturer.
Erba Lachema s.r.o
Karásek 2219/1d, 621 00 Brno
Czech Republic
Tel: +420 517 077 111
e-mail: diagnostics@erbamannheim.com
Website : https://www.erbamannheim.com/en/product-support/
Contact your local technical support: (Print this page and write or paste contact infor-
mation for easy access)
UM/22/17/C
15