Professional Documents
Culture Documents
10024980G00 - Cpu Board Requirements Specification, PB 540
10024980G00 - Cpu Board Requirements Specification, PB 540
REV DESCRIPTION
1.1 Purpose
The purpose of this document is to provide the requirements for the CPU Board.
1.2 Scope
This document provides the requirements for the CPU Board used for PB640, PB560, PB540 and
PB520.
1.3 REVISION HISTORY
Revision Author Change Description
A G. Cravero Initial Release
B F.Cotteaux Memory life cycle change from 1,000,000 to 100,000
because one component on the BOM don’t match the last
value.
Watchdog function tolerance change from 1% to 2%.
C F.Cotteaux Add note on the IPC Class II/III requirement
D G Sánchez Clarify requirements, update to standard format,
addressed open tracker issues.
E G Sánchez Incorporate updates from Verification Review.
F A.Fitzpatrick No change to document. Only a BOM change.
G M. Couteau Updates for PB520 exclusion of exhalation flow
requirements
1.5 Definitions
°C Celsius Degree
A Ampere
AC Alternating Current
DC Direct Current
Kb Kilobytes
kHz Kilo Hertz
LED Light Emitting Diodes
Mb Megabytes
mA Milliamps DC
mbar Millibar
ms Milli Seconds
2.0 OVERVIEW
The CPU board contains the logic to execute application code to read user input, control the turbine to
provide breath delivery, provide error checking, and provide information to the user.
3.1 General
HWSCPB1 The system must be able to measure the 24V supply voltage from 22V to 26V in order to
watch supply voltage.
HWSCPB2 The system must be able to measure the 24V supply voltage from 22V to 26V in order to
detect a failure of the power fail detection system.
HWSCPB3 The inrush current of the system must be lower than 2A and shorter than 100 ms.
HWSCPB4 Maximum system power consumption must be limited to 15W.
3.2 5 Volt Supply
HWSCPB5 The 5 Volt Supply shall have an input of 24.0V +/- 1.2V
HWSCPB6 The 5 Volt Supply shall produce an output of 5.00V +/- 0.25V
HWSCPB7 The 5 Volt Supply shall be capable of sourcing 3A
T1min = 70ns
AO ó A2
CS/
WE/
3.24 Watchdog
A watchdog function shall be provided to detect execution of processor instructions.
HWSCPB86 The watchdog shall generate a reset pulse if it is not strobed at a time interval shorter
than 1.6 +/-0.65s.
HWSCPB88 If the reset is activated by a timeout; it shall be active for a minimum of 140ms and a
maximum of 280ms.
A supervisory function shall be provided to detect loss of voltage.
HWSCPB89 The supervisory function shall generate a reset if Vcc voltage drops below [4.50V;
4.75].
HWSCPB90 The reset pulse of the supervisory function shall remain active until Vcc goes over
[4.54V; 4.75] (hysteresis: +0.01V compared to the trigger detection. Refer to HWSCPB89).
HWSCPB91 If reset is generated by the supervisory function the minimum pulse width shall be 140
ms.
HWSCPB92 The signal shall go inactive when the voltage returns to specification and the minimum
pulse width has been met.
HWSCPB93 The system must be warned when the supply (+24V) drops to 13.01V +/- 2% before
system shut off on power loss and must active a trap function.
3.25 Clock
HWSCPB94 The CPU Board shall provide timestamp information.
HWSCPB95 Timestamp information shall be kept for duration of 3 years, if the CPU board is not
supplied (main switch switched off).
Tolerance %. Not
Flow Tolerance Calibrated.
sccm Nominal (VDC) Sensor only
1000 5 0.5 10.00%
900 4.9 0.505 10.31%
800 4.8 0.51 10.63%
700 4.66 0.513 11.01%
600 4.42 0.511 11.56%
500 4.18 0.509 12.18%
400 3.82 0.501 13.12%
300 3.41 0.4605 13.50%
200 2.96 0.418 14.12%
100 2.3 0.355 15.43%
0 1 0.25 25.00%
Tolerance %. Calibrated.
Flow With whole supply chain
l/min measure
145 5.00%
135 5.00%
90 5.00%
60 5.00%
37 5.00%
12 8.00%
5 10.00%
0 NA
Tolerance %. Not
Flow Tolerance Calibrated.
sccm Nominal (VDC) Sensor only
1000 5 0.5 10.00%
900 4.9 0.505 10.31%
800 4.8 0.51 10.63%
700 4.66 0.513 11.01%
600 4.42 0.511 11.56%
500 4.18 0.509 12.18%
400 3.82 0.501 13.12%
300 3.41 0.4605 13.50%
200 2.96 0.418 14.12%
100 2.3 0.355 15.43%
0 1 0.25 25.00%
Tolerance %. Calibrated.
Flow With whole supply chain
l/min measure
145 5.00%
135 5.00%
90 5.00%
60 5.00%
37 5.00%
12 8.00%
5 10.00%
0 NA
Tolerance %. Calibrated.
Pressure With whole supply chain
mbar measure
40 5%
0 NA
4.1 Size
HWSCPB106 The length (L1) of the PCBA shall be 190mm +/- 1mm
HWSCPB107 The length (L2) of the PCBA shall be 58.5mm +/- 1mm
HWSCPB108 The length (L3) of the PCBA shall be 96.5mm +/- 1mm
HWSCPB109 The width (W1) of the PCBA shall be 100mm +/- 1mm
HWSCPB110 The width (W2) of the PCBA shall be 20mm +/- 1mm
HWSCPB111 The thickness (T) of the PCBA shall be 1.60mm +/- 0.5mm
L1
W1
3 holes for the mounting
L2 W2
T
L3
4.2 Mounting
HWSCPB112 3 holes Ø 3.5mm shall be plan to fix the CPU board on the device.
4.3 Cooling
N/A.
4.4 Fabrication
HWSCPB113 The Printed Circuit Board shall be fabricated per standard:
IPC-610D Class III: 2005, Acceptability for Electronic Assemblies.
Exceptions shall be listed on the fabrication drawings.
4.5 Protection
N/A.
4.6 Labeling
HWSCPB114 The PCBA shall be labeled with its Name, Part Number and Revision which is also
human readable.