Professional Documents
Culture Documents
Tem 5025e
Tem 5025e
5025E
ENGINEERING MANUAL
.. -w.
PREPARATION OF
.
, .
f
ENGINEERING MANUALS TEM
TOKYO @ JAPAN
)
M ENOINEZRIX h. PREPARATION OF ELECTRICAL WORK DRAWING 5025E
CONTENTS
PAGE
1. GENERAL
1.1 Purpose 2
1.2 Scope 2
1.3 Attentions Required in the Application 3
2. TITLE AND SYMSOLS TO BE USED IN DRAWINGS
.- .
ENGINEERING MANUALS TEM
TOKYO @ JAPAN
/
b E.wxxE~xIx b. PREPARATION OF ELECTRICAL WOM. DRAWING 5025E
I I
ISSUED JUL.27’88 PAGZ 2 OF 12
1. GEhJERAL
1.1 PUTDOSE
1.2 Scope
FORM A.G30.014
t
ENGINEERING MANUALS TEM
TOKYO @ JAPAN
/
% EmINzxxIw b. PREPARATION OF ELECTRICAL WORK DRAWiNG 5025EI
(2) In using this manual, refer also to the sample drawings pre?ared
separately.
Kinds of the sample drawings are as shown in the Attached Tabl= 1
“Sample Drawing List (Electrical)”.
.
(3) When any foreign country’s (non-Japanese) standards are to be applied
in the project there may be cases where the applicable symbols and alsc
design standards are quite different from those shown in this manual.
Therefore, discuss with the assigned engineers in regard to this
matter.
~ F-M A-G30.014
-?
.
TOKYO @ JAPAN
)
M EWINEERIK -,
ENGINEERING MANUALS
PREPARATION OF ELECTRICALWORK DRAWING
1- TEM
5025E
3. PREPARATION OF DRAWINGS
The purpse of use and matters which at least shall be described are as
shown below for each kind of drawing. Examples of the drawings are shown in
the sample dzawings.
(c) symbols
(a) Each of the layout drawings may be made by use of a base drawing,
which is a reproducible original of the plot plan dzawing made in
advance.
(c) Any matters which are to be heeded in the construction work, but
cannot be depicted in drawing, should be indicated by “Notes”
described in blank spaces.
.
ENGINEERING MANUALS TEM
TOKYO @ JAPAN
/
ti Ew~xz~x~x -. PREPARATION OF ELECTRICAL WORK DRAWING 5025E
F-M A-G30.014
ENGINEERING MANUALS TEM
TOKYO @ JAPAN
k EW’INXEmM h. PREPARATION OF ELECTRICAL WORK DRAWING 5025E
I }
ISSUED JUL.27’88 PAGE 6 OF 12
FWM A-G30.014
J
ENGINEERING MANUALS TEM
TOKYO @ JAPAN
)
- EMINE~RIW k. PREPARATION OF ELECTRICAL WORK DRAWING 5025E
~ FORM A-G20.014
ENGINEERING MANUALS TEM
TOKYO @ JAPAN
)
Tm hxxzzww cm. PREPARATION OF ELECTRICAL WORK DR~wING 5025E
FORM A-G30,014
ENGINEERING MANUAiS TEM
T OK Y O @ JAPAN
W E;IXEZRXW -. PREPARATION OF ELECTRICAL” WORK DRAWING 5025E
J
FWM A-G30.014
ENGINEERING MANUALS TEM
TOKYO @ JAPAN
/
m EmIxzzRIw k. PREPARATION OF ELECTRICAL WORK DRAWING 5025E
(b) Quantity
F-M A-G30.014
?
ENGINEERING MANUALS TEM
TOKYO @ JAPAN
)
~” EMINEZRIX * PREPARATION OF ELECTRICAL” WORK DRAWING 5025E
(c) Rated voltage, type, No. of cores, size, length, and drum No. of
the cable
FWM A-G30.014
10
TOKYO
I
/ JAPAN
- EMIN~ERIM -.
ENGINEERING MANUALS
PREPARATION OF Electrical WORK DRAWING
TEM
5025E
(b) Dwg No. of “Lighting Layout Dwg” where the object lighting
fixtures are described.
(d) For each branch circuit — total capacity, current, and the size
of cable or wire to be connected.
Remarks: 1. Entry of the lighting fixtures shall be done for each of day-
and-night lights, night lights, and emergency lights,
separately.
2. The drawing shall be made on” one sheet per each distribution
bard.
3. The size of drawing shall be A3, as a rule.
F~M A-G30.014
TEM5025E
.- .