Professional Documents
Culture Documents
Lampiran Spesifikasi SCADA
Lampiran Spesifikasi SCADA
Parameter Technical
Sensor type Tipping bucket with measuring bucket
Sampling area 200 cm2
Tick sensor Bounce-free reed contact
Resolution 0.5 mm
Accuracy ±2%
Supply voltage 12 VDC
Installation method Flange or clamp-on pipe
VIII-1
A-04.Visual Sensor
Parameter Technical
Lens 3.6 mm, high-performance color CMOS sensor
Minimum illumination 0.05 lux (w/o IR), 0 lux (with IR)
Connection USB (data and power)
Video format Standard compressed JPEG, 1920x1080
Adjustable parameter 14, including brightness, contrast, saturation, hue, color balace, gamma
API application Get camera, snapshot to file, capture video to file
Housing Outdoor, wheatear proof
Parameter Technical
Transducer type Synchro-transmitter / potentiometer / pulse / constant spring loaded
Measuring method Shaft-rotation or wire-messenger
Measuring range 0 – 400 cm
Resolution 1 mm
Accuracy 0.1% FS
Pulse signal 20 ms pulse for every 1 mm increment/decrement
Input voltage 12 VDC or 220 VAC
Output 4 – 20 mA or serial data (RS-485, ModBus)
Enclosure Outdoor, weather proof
Parameter Technical
Control interface Electric relay
Control command Open Gate, Close Gate, Stop
Status data Power On, Full Open, Full Close, Overload
Enclosure Outdoor, weather proof
Protection level IP-64, minimum
VIII-2
A-06. Automatic Wheater Station Sensors
Parameter Technical Specification
Transducer type Tipping bucket or Doppler Radar
Rainfall Measuring range 0 to 999.8 mm or 0 to 200 mm/hour
Resolution 0,2 mm
Accuracy ± 4%
Transducer type Capacitance type
Barometric
Pressure
Resolution 1 degC
Accuracy ± 0,3 degC
Direction
1 – 360o
Wind
Measuring range
Resolution 1o
Accuracy ± 3o
Transducer type Silicon photovoltaic detector or equivalent
Solar
4
A-11. Installation Material & Protection Accessories
Parameter Technical Specification
Equipment installation □ Every electronics equipment shall be installed in an
equipment enclosure
□ Enclosure material shall be metal sheet with powder coating
finishing or hard fiber
□ Equipment installation on a wall will be mounted with a proper
metal bracket
Cable and wire installation □ Every cable and wire installation shall be protected with
PVC conduit or ducting
□ Cable installation on wall will use proper cable clamp
□ Direct buried cable shall be protected with metal conduit
Cable termination □ Every cable termination shall be covered in a terminal box
□ Terminal box material shall be metal sheet with powder coating
finishing or hard fiber
□ Terminal strip shall be corrosion proof
□ Inlet of terminal box shall be covered with cable gland
Protection Accesories □ Installation material must be included lightning arrester device
either for antenna, signal or power input
□ Every electronic or electrical installation must be protected against
vandalism or stealing with appropriate enclosure or
cage/fence.
A-12. Installation, Testing & Programming
Parameter Technical Specification
Installation Procedure Contractor shall submit installation plan to be approved by the user.
Installation plan consist of :
□ Work schedule
□ Procedure
□ Drawings
□ personnel
□ Equipment
□ Safety
Personnel Installation works shall be perform by qualified personnel, as follows
:
□ Device installation : STM or equivalent
□ Cable, termination, networking : STM or equivalent
□ Setting & programming : S1 instrumentation/electronic
□ Application programming : S1 information technology/
computer
Safety Adequate Personal Protective Equipment (PPE) shall be applied to personnel
during installation works.
5
A-13 Solar Power, Solar Panel, 24VDC, 300Wp
Parameter Technical Specification
Cell type Mono or poly crystalline silicon
Power capacity 300 Watt maximum
Enclosure High transparent tempered front glass,
Anodized Aluminum Alloy Frame
Junction box IP-65
A-14 Solar Power, Deep Cycle Battery, 24VDC, 100aH
Parameter Technical Specification
Storage Battery
Battery type Sealed Valve Regulated Lead Acid Gel or Deep-Cycle Battery
Capacity 100Ah 24VDC or 2 X 100Ah 12VDC
Operating temperature - 15 to 45 degC
A-15 Solar Power, Charge Controller/Inverter. 5kVA
Parameter Technical Specification
Controller type Hybrid solar inverter
Rated Voltage 12/24/48 VDC input, 220V AC output
Rated capacity 5 kVA
Include LED/analog status display, main-power charger & inverter,
60A MPPT controller, ATS
A-17 Main Electric Connection, 6.600 watt
Parameter Technical Specification
Installed electric capacity 6.600 watt, 1-phase
Subscription type Pre-paid (using token)
Accessories • Electric power meters including MCB and protective boxes
• Grounding, maximum resistance is 5 Ohms
• Additional electric poles (if needed)
• Down-step transformer to 220V line, if needed