Professional Documents
Culture Documents
Magner 22 User Manual
Magner 22 User Manual
Magner 22 User Manual
USER MANUAL
MAGNER 22
Preface
Thank you for choosing the mixed bill value counter. This machine represents the latest development in
Carnation technology. In order to make the best use of this currency counter and its mixed counting
capabilities, please read the manual carefully, and familiarize yourself with the operating procedures.
Contents
Features··········································1
Unpacking·········································1
Exterior··········································2
Functions·········································4
User Menu·········································5
Troubleshooting·······································7
Safety············································8
Replacing the fuse······································8
Maintenance········································8
Specifications········································8
1. Features
2. Unpacking
-1-
3. Exterior
Number Parts
1 Stacker
2 Banknote receiving sensor
3 Banknote receiving wheel
4 TFT display
5 Start sensor
6 Hopper with adjustable guides
7 Handle
8 Power cord jack
9 On/off switch
10 RS232 port
11 USB port
12 R45 port (LAN)
13 Adjusting screw
14 Android port
-2-
3. 2 Panel
MODE: Counting mode settings: CNT mode (Count), SDC mode (Single Denomination Count) & MDC
mode (Mixed Denomination Count).
Button “+ADD/DISP”: ADD function on/off. Also served as button to press to show counting details.
Button “CURRENCY”: Currency selection.
Button “BATCH”: Batch function on/off.
Button “→”: Right navigation button. When BATCH is on, press to add 10.
Button “←”: Left navigation button. When BATCH is on, press to reduce 10.
Button “↑”: Upward navigation button. When BATCH is on, press to add 1.
Button “↓”: Downward navigation button. When BATCH is on, press to reduce 1.
Button “START/STOP”: Start counting / Back to Main interface. Also served as confirm selection in
Main interface.
Button “SPEED”: Speed selection. 800/1000/1200 notes/min for CNT mode, 800/1000 notes/min for
SDC & MDC modes.
Button “PRINT”: Send count report to print.
Button “ESC”: Clear the number of counted banknotes / Back to previous interface.
-3-
4. Functions
4.3 Others
-4-
shows last 8 digits. If want to reset to 0, press “ESC”.
4.3.4 Batch Counting
When you need to count out equal batches of banknotes, press the "BATCH" key. When "BATCH
FUNCTION: ON" is displayed on the TFT, the "BATCH" function has been turned on and the current batch
setting is 100. Press again "BATCH", it will turn off this function.
Press”→”to add 10, press“←”to reduce 10, press “↑”to add 1, press “↓”to reduce 1.
4.3.4 Speed
Press “SPEED” at main interface to change the speed, 800/1000/1200 notes/min for CNT mode,
800/1000 notes/min for SDC & MDC modes.
4.3.5 Auto/Manual Start
Press“↑”at main interface to change the counting start mode, auto/manual.
5. User menu
Press “↓”to enter the menu in main interface. TFT shows like follow:
-5-
5.4 Print the Counting result
Connect printer to the machine, then turn on, start counting banknotes, after counting is complete, press
“+ADD/DISP” to show up the detail results, press “PRINT” to enter printer menu, press again to confirm
printing.
-6-
6. Troubleshooting
The machine will automatically perform a system self-test after it is turned on. Most error codes are
caused by banknote jam or dusty sensors. Check for banknote jams and use a brush to clean the sensors,
and then restart the machine.
Remove the banknote from the machine and/or remove dust from hopper
Hopper Sensor Error sensor. Adjust the machine to the right position to avoid direct sunlight.
Remove the banknote from the machine and/or remove dust from stacker
Stacker Sensor Error sensor. Avoid direct sunlight on the stacker sensor.
Remove the banknote from the machine and/or remove dust from CIS
IMAGE ERROR sensor.
Remove the banknote from the machine and/or remove dust from CIS
IR ERROR sensor.
-7-
Safety
■ If the room temperature is lower than 20℃, wait 3 minutes after turning the machine on before
operating.
■ The machine should be operated in a room with good ventilation, and kept away from strong sunlight
and/or magnetic field.
■ The machine must be plugged into grounded electric outlets ONLY.
■ The voltage must be in the range of 100~240V AC to avoid malfunction / breakage.
■ All external rollers and wheels must NOT be oiled or greased to avoid malfunction.
■ Dusts on CIS image detecting module, IR sensors, and magnetic sensor must be thoroughly cleaned at
least once a week. You may remove dust build-up on the exposed parts of the machine with the
brush provided.
Maintenance
1. Cleaning the Machine
1.1 For optimal performance the machine needs to be cleaned regularly.
1.2 Clean the hopper and stacker with the enclosed brush.
3. In order to avoid disturb, wait 5 seconds before open the machine when turn off the machine, and / or
wait 5 seconds to turn on the machine after close the machine.
Specifications
Dimensions: 13.8”(W)*12.8”(D)*12”(H) / 35CM(W)*32.5CM(D)*30.5CM(H)
Weight: 16.5lb / 7.5KGS
Counting Speed: 800/1000/1200 notes/min for CNT mode, 800/1000 notes/min for SDC & MDC modes
Note Size Range: Min.: 2.36X 4.33in/ 60mm (Width) X 110 (Length)
Max.: 3.54X 7.28in/ 90mm (Width) X 185mm (Length)
Note Thickness: Min.: 0.0031(0.08mm) Max.:0.0047(0.12 mm)
Feed system: Roller Friction System
Hopper Capacity: 400 ~ 500 notes
Stacker Capacity: 200 notes
Power Supply: AC100 ~ 240V ± 10%, 50/60Hz
Current: Maximum 1.8A
Power Consumption: <50W
Temperature: 32℉~95℉(0℃ ~ 35℃ )(Operating)
Working Environment: 14℉~140℉(-10℃ ~ 60℃) (Stocking)
Humidity: 20%~90%
Interface: RS232, USB, LAN, Android
-8-