Professional Documents
Culture Documents
Ivms 5601
Ivms 5601
IVMS-5601
IVMS-7001
Bedienungs- und Einbauanleitung
Operating and installation instructions
Notice d’emploi et de montage
Istruzioni d’uso e di installazione
Gebruiksaanwijzing en inbouwhandleiding
Bruks- och monteringsanvisning
Instrucciones de manejo e instalación
Instruções de serviço e de montagem
Betjenings- og monteringsvejledning
http://www.blaupunkt.com
7 5 3
8 6 4 2
10 11
12
Downloaded from www.Manualslib.com manuals search engine
TABLE OF CONTENTS
Notes / Accessories .............. 14
DEUTSCH
Fitting ..................................... 14
Prepare the working area .............. 14
Mark out the dimensions ................ 15
Carefully cut open the headrest
ENGLISH
cover ............................................. 15
Open the headrest and remove
filling and other items ..................... 15
Lay the cable through the
FRANÇAIS
headrest ........................................ 16
Insert the mounting frame in
the headrest .................................. 16
Insert the monitor .......................... 16
Check and adjust the monitor then
ITALIANO
apply the Velcro strips ................... 17
Removal ................................. 17
OSD functions ........................ 18
NEDERLANDS
Main menu .................................... 18
Sub-menu ..................................... 18
Technical data ........................ 20
Guarantee .............................. 21
SVENSKA
ESPAÑOL
PORTUGUÊS
DANSK
13
Downloaded from www.Manualslib.com manuals search engine
NOTES / ACCESSORIES FITTING/REMOVAL
Important notes Fitting
This device is not intended for fitting in Note
the forward section of the passenger It is recommended that the fitting is car-
compartment where it could also be ried out at a specialist workshop.
seen by the driver. Fitting this device in
any part of the vehicle where it could Prepare the working area
interfere with or distract the driver’s at- ➮ Remove the headrest, and place it
tention is dangerous and is not permit- on a working surface that has been
ted. The manufacturer cannot accept cleared and cleaned, where the
responsibility for any damage caused further assembly procedures may
as a result of improper fitting of this de- be carried out.
vice.
Note:
Take appropriate action to ensure that
To avoid the risk of electrical
the headrest is not damaged while fit-
shock, the device must be protected
ting the monitor.
from water and moisture, and must
not be opened. Dangerously high
voltages are generated inside the
device.
14
Downloaded from www.Manualslib.com manuals search engine
FITTING/REMOVAL
Mark out the dimensions
DEUTSCH
➮ Feel the covering of the headrest
carefully to ensure that there are
no invisible parts that would pre-
vent the monitor from being fitted.
ENGLISH
Use the cardboard template provided
to mark out the area that will need to be
cut.
FRANÇAIS
Open the headrest and remove
filling and other items
➮ Carefully lift the covering material
ITALIANO
away from the cut area.
➮ Adjust the cutting depth of the knife
to about 2.5 cm, and cut into the
headrest following a line about
NEDERLANDS
0.5 cm inside the marked edge.
Carefully cut open the headrest ➮ Carefully lift the filling material at
cover one corner, and cut deeper into the
Use a knife with an adjustable cutting material with the knife.
➮ Remove the filling material in small
SVENSKA
depth to cut out the planned area.
➮ Make the first cut inside the pieces.
marked area at a point about ➮ As you do this, lift one piece of the
0.5 cm from one of the corners, filling material, and ensure that the
then make a diagonal cut to a point cut is being made to an even
ESPAÑOL
about 0.5 cm from the opposite depth.
corner. To remove other pieces, use a Dremel
➮ Make a similar cut between the saw or another suitable tool.
other two diagonally opposed cor-
PORTUGUÊS
ners.
DANSK
15
Downloaded from www.Manualslib.com manuals search engine
FITTING/REMOVAL
➮ Insert the monitor to check that it Insert the mounting frame in the
will fit into the cut area, and make headrest
adjustments if necessary.
➮ Before connecting the monitor,
pass the connecting cables
through the holes provided in the
mounting plate, as shown in the il-
lustration.
➮ Insert the mounting plate into the
area that has been cut out, and fix
it in place with appropriate fasten-
ings.
Monitor
Mounting plate
16
Downloaded from www.Manualslib.com manuals search engine
FITTING/REMOVAL
Check and adjust the monitor Removal
DEUTSCH
then apply the Velcro strips ➮ To remove the screen, insert the
➮ Connect the monitor, place it tem- extraction tool between the screen
porarily in the cut-out, and place and the mounting plate.
the headrest into position. ➮ Insert the extraction tool at the
ENGLISH
➮ Check the various monitor settings place where a slot has been pro-
such as brightness, headphone vided between the screen and the
function, volume control and so on. mounting plate.
➮ Then attach the Velcro strips to the
FRANÇAIS
rear of the monitor, and push the
frame onto the headrest.
Take care not to press the screen
itself, and apply pressure only in
Extraction tool
the region of the frame.
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
DANSK
17
Downloaded from www.Manualslib.com manuals search engine
FUNCTION
OSD functions Sub-menu
Main menu ➮ To reach the following menu op-
tions, select “MISC” from the main
➮ Call up the main menu by pressing menu.
the “MODE” key on the main de-
➮ When in the sub-menu, select the
vice, or “MENU” on the remote
“MAIN MENU” option to return to
control unit.
the main menu, then select “EXIT”
➮ Select the “EXIT” option to leave to leave the OSD menu.
the OSD menu again.
AUTO PROGRAM
VOLUME
BRIGHTNESS FM CHAN: OFF
CONTRAST AV OUT: LINE
COLOR
TINT ZOOM: FULL
MISC SPEAKER: OFF
EXIT REVOLVE: LEFT RIGHT
REVOLVE: UP DOWN
+ RESET PICTURE
MAIN MENU
● VOLUME:
Volume adjustment Note:
Rotate UP DOWN (off function).
● BRIGHTNESS:
● AUTO PROGRAM :
Brightness adjustment
See the “AUTO PROGRAM” function
● CONTRAST:
in the description of the remote control
Contrast adjustment unit.
● COLOR: ● AV OUT:
18
Downloaded from www.Manualslib.com manuals search engine
FUNCTION
● ZOOM : ● RESET:
DEUTSCH
This mode is pre-set by default to “full”. Select the “RESET PICTURE” option to
You can make the various adjustments return all the adjusted parameters to
for the display mode that you want by their factory pre-set values.
pressing the or keys for the fol- ● MAIN MENU:
lowing options:
ENGLISH
If you are in the sub-menu, select this
Full = display a 4:3 signal in a 16:9 im- option to return to the main menu.
age format
● AUX (input):
ZOOM1 = picture height, zoom factor =
Video input for connecting an addition-
FRANÇAIS
4/3
al signal source (games console, cam-
WIDTH1 = picture height and different corder, etc.)
picture width
Note:
Normal = edge ratio 4:3
Only use original Blaupunkt
ITALIANO
ZOOM2 = zoom factor = 8/7 accessory 7 607 001 510.
WIDTH = different picture widths Or else use a mono plug.
WIDTH2 = picture height and different
picture width
NEDERLANDS
ZOOM3 = picture height, zoom factor =
8/7
● SPEAKER:
SVENSKA
switch the monitor loudspeaker on or
off with the or keys.
● REVOLVE
ESPAÑOL
you can revolve the display on the
screen.
PORTUGUÊS
DANSK
19
Downloaded from www.Manualslib.com manuals search engine
TECHNICAL DATA
Technical data Resolution (pixels):
5.6": 720 (H) x 234 (W) =
System: NTSC/PAL dual
168,480 pixels
system
7": 1440 (H) x 234 (W)
Power supply / consumption: = 336,960 pixels
112 V DC
± 10%, <700 mA Black light: cold cathode tube
Screen technology:
TFT (thin film tran-
sistor) display sys-
tem
Subject to changes!
20
Downloaded from www.Manualslib.com manuals search engine
GUARANTEE
Guarantee
DEUTSCH
The scope of the guarantee depends
on the regulations in force within the
country in which the unit was purchased.
If your unit develops a fault, please con-
ENGLISH
tact your dealer and present the pur-
chase receipt.
If the statutory guarantee period in your
country is less than 12 months, Blau-
FRANÇAIS
punkt will grant a 12-month manufac-
turer’s guarantee. This guarantee does
not cover damage due to wear, incor-
rect usage or commercial use.
If you wish to enforce a claim under the
ITALIANO
manufacturer’s guarantee that is provid-
ed by Blaupunkt, please send the faulty
equipment together with the purchase
receipt to the Blaupunkt customer serv-
NEDERLANDS
ice centre in your country. You can find
out which address is closest to you by
contacting the telephone hotline listed
on the back page of this booklet. Blau-
punkt retains the right to rectify defects
SVENSKA
or supply a replacement.
ESPAÑOL
PORTUGUÊS
DANSK
21
Downloaded from www.Manualslib.com manuals search engine
Service-Nummern / Service numbers / Numéros du service après-
vente / Numeri del servizio di assistenza / Servicenummers /
Telefonnummer för service / Números de servicio / Números de
serviço / Servicenumre
Brasil
(Mercosur) (BR) +55-19 3745 2769 +55-19 3745 2773
Malaysia
(Asia Pacific) (MAL) +604-6382 474 +604-6413 640
Blaupunkt GmbH
08/02 CM/PSS2 - 8 622 403 177