Professional Documents
Culture Documents
ppt1B75.pptm (Autosaved) 2
ppt1B75.pptm (Autosaved) 2
ppt1B75.pptm (Autosaved) 2
PRESENTED BY
M.PREM KUMAR (TEAM LEAD)/ ECE REGNO: 962919106003
M.PANEER SELVAM/CSE REGNO:962919104009
M.JIJO/CSE REGNO:962919104008
M.ASWIN/ECE REGNO:962919106002
VINS CHRISTIAN COLLEGE OF ENGINEERING, CHUNKANKADAI
GUIDED BY
Mrs.J.JEROPHINE BENI,M.E;
ASSISTANT PROFESSOR/CSE
➢ INTRODUCTION
➢ OBJECTIVE
➢ EXISTING METHOD
➢ PROPOSED METHOD
➢ DATAFLOW DIAGRAM
➢ MODULES
➢ RESULT
➢ FUTURE ENHANCEMENT
➢ CONCLUSION
➢
▪ Child safety is a challenging problems now a days.
▪ Need high surveillance for ensuring the safety among children.
▪ In the modern world smart phones are playing major role for ensuring the safety,
Where some mobile based application provide alert systems.
▪ Not provide complete solution for problems which is faced by childrens
▪ Increasing need for the safety of little children
➢
❖ DIS-ADVANTAGES
▪ The child could not produce the exact alert command during a panic condition.
▪ The command produced may not match with the previously stored command.
▪ Required manual intervention.
➢
▪ It does not need voice command.
▪ Introduced Geo-fence.
▪ Uses the Arduino kit and the Arduino kit forms the core.
▪ Arduino nano is connected with NRF24L01 transceiver module which acts as
as a transmitter and the Arduino nano board is powered up by a lithium polymer
Battery.
▪ ESP8266 Node MCU WiFi board is connected with another NRF24L01
transceiver module which act as a receiver that complement the system.
▪ The Arduino nano and NRF module (Transmitter) acts as a safety gadget.
▪ To transmit data to the NRF module(receiver).
▪ NRF receiver sends the data from the transmitter to the Node MCU board.
▪ All this setup is build under a Geo-Fence.
▪ If the transmitter exits the Geo-Fence the continuous transmission of dataflow
From transmitter to receiver gets stopped.
▪ Since the dataflow is stopped, The Node MCU sends a alert notification to the
parent’s or caretaker’s mobile phone.
➢
Mobile
Mobile
Connection lost
Continuous
Arduino Node Arduino Node
nano Data MCU nano MCU
transmission
➢
Geo fence
Continuous
data
transmission
Wearable
and reception Transmitter
Device like
which is in
watch or
stable state
wrist band
NRF24L01 Geo fence NRF24L01
Transceiver
Transceiver
(Transmitter)
(Receiver) module
module
Continuous
data
transmission
and reception ESP8266
Arduino
Nano board Node MCU board
Connection is
lost
Aurduino ESP8266
Nano board Node MCU board
Connection is Mobile
lost
Aurduino
Nano board
ESP8266 Send Notification
Node MCU board
Lithium Polymer
Battery which act
as power source Connected with
laptop which act
as power source
➢
❖ NRF24L01 Transceiver Module:
NRF24L01 Transceiver Module is designed to operates
In a 2.4GHz ISM band. It is used as both transmitter and
Receiver in the network. It ranges upto 100m.
❖ Arduino Nano:
Arduino nano is a single board micro-controller. Operates in 5v with
Input voltage of about 5-20v. Used as transmitter. Connected with
NRF transceiver module which act as a transmitter. It’s a small sized
Micro controller.
❖ ESP8266 Node MCU Board :