Professional Documents
Culture Documents
FMB910 Quick Manual v1.7
FMB910 Quick Manual v1.7
FMB910 Quick Manual v1.7
Warranty ........................................................................................... 16
Table of Contents ............................................................................... 2
Warranty Disclaimer........................................................................ 16
Know your device ............................................................................... 3
Pinout ................................................................................................. 4
How to insert Micro SIM card and connect the battery ................ 6
LED indications................................................................................. 11
Characteristics.................................................................................. 11
2 FMB910 | Wiki
Know your device
3 FMB910 | Wiki
Pinout
Table 1 FMB910 pinout
4 FMB910 | Wiki
Wiring scheme
1
Automotive relay
5 FMB910 | Wiki
Set up your device
How to insert Micro SIM card and
connect the battery
1. Gently remove FMB910 cover using plastic pry tool from both
sides.
2. Insert Micro-SIM card as shown with PIN request disabled or
read Security info how to enter it later in Configurator. Make sure
that Micro-SIM card cut-off corner is pointing forward to slot.
3. Connect battery as shown to device. Position the battery in
place where it does not obstruct other components.
4. Attach device cover back. Device is ready to be connected.
6 FMB910 | Wiki
PC Connection (Windows) Configuration (Windows)
1. Power-up FMB910 with DC voltage 6-30 V power supply using At first FMB910 device will have default factory settings set. These
power cable. LED’s should start blinking, see “LED indications”. settings should be changed according to the user's needs. Main
2. You are now ready to use the device on your computer. configuration can be performed via Teltonika Configurator
software. Get the latest FMB910 Configurator version from here.
Configurator operates on Microsoft Windows OS and uses
How to install USB drivers prerequisite MS .NET Framework. Make sure you have the correct
7 FMB910 | Wiki
Various Status window tabs display information about GNSS, GSM,
I/O, Maintenance and etc. FMB910 has one user editable profile,
which can be loaded and saved to the device. After any
modification of configuration the changes need to be saved to
device using Save to device button. Main buttons offer following
Figure 8 Language selection
functionality:
Configuration process begins by pressing on connected device
(Figure 9 Device connected via USB). 1. Load from device – loads configuration from device.
Figure 9 Device connected via USB 4. Save to file – saves configuration to file.
After connection to Configurator Status window will be displayed 5. Update firmware – updates firmware on device.
(Figure 10 Configurator Status window). 6. Read records – reads records from the device.
default.
8 FMB910 | Wiki
Default configuration settings
Quick SMS configuration Movement and ignition detection:
Default configuration has optimal parameters present to ensure Vehicle movement will Ignition will be detected
best performance of track quality and data usage. be detected by by vehicle power voltage
accelerometer between 13,2 – 30 V
Quickly set up your device by sending this SMS command to it:
Device makes a record On Moving if one of these events happen:
" setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0;"
300 seconds passes Vehicle turns 10 degrees
Note: Before SMS text, two space symbols should be inserted.
Speed difference
GPRS settings:
Vehicle drives 100 between last coordinate
• 2001 – APN meters and current position is
• 2002 – APN username (if there greater than 10 km/h
are no APN username, empty Device makes a record On Stop if:
field should be left) 1 hour passes while
• 2003 – APN password (if there vehicle is stationary
and ignition is off
are no APN password, empty
field should be left) Records sending to server:
If device has made a
Server settings:
record it is sent to the
• 2004 – Domain server every 120
• 2005 – Port seconds
• 2006 – Data sending protocol After successful SMS configuration, FMB910 device will synchronize
(0 – TCP, 1 – UDP) time and update records to configured server. Time intervals and
default I/O elements can be changed by using Teltonika
Configurator or SMS parameters
9 FMB910 | Wiki
Mounting recommendations
• Connecting ignition wire
▬ Be sure to check if it is a real ignition wire i.e. power does
not disappear after starting the engine.
• Connecting wires ▬ Check if this is not an ACC wire (when key is in the first
▬ Wires should be fastened to the other wires or non-moving position, most of the vehicle electronics are available).
parts. Try to avoid heat emitting and moving objects near ▬ Check if power is still available when you turn off any of
the wires. vehicles devices.
▬ The connections should not be seen very clearly. If factory ▬ Ignition is connected to the ignition relay output. As
isolation was removed while connecting wires, it should be alternative, any other relay, which has power output when
applied again. ignition is on, may be chosen.
▬ If the wires are placed in the exterior or in places where they
can be damaged or exposed to heat, humidity, dirt, etc., • Connecting ground wire
additional isolation should be applied. ▬ Ground wire is connected to the vehicle frame or metal
▬ Wires cannot be connected to the board computers or parts that are fixed to the frame.
control units. ▬ If the wire is fixed with the bolt, the loop must be connected
to the end of the wire.
• Connecting power source ▬ For better contact scrub paint from the spot where loop is
▬ Be sure that after the car computer falls asleep, power is still going to be connected.
available on chosen wire. Depending on car, this may
happen in 5 to 30 minutes period.
▬ When the module is connected, measure the voltage again
to make sure it did not decrease.
▬ It is recommended to connect to the main power cable in
the fuse box.
▬ 3 A, 125 V external fuse shall be used.
10 FMB910 | Wiki
LED indications
Characteristics
Table 3 Status LED indications
BEHAVIOR MEANING
Basic characteristics
Blinking every second Normal mode
Table 4 Basic characteristics
Blinking every two seconds Sleep mode
MODULE
Blinking fast for a short time Modem activity
Name Teltonika TM2500
Device is not working or Device is in Technology GSM/GPRS/GNSS/BLUETOOTH
Off
boot mode
GNSS
GPS, GLONASS, GALILEO, BEIDOU,
GNSS
SBAS, QZSS, DGPS, AGPS
Receiver 33 channel
Tracking sensitivity -165 dBM
Position accuracy < 2.5 CEP
Velocity accuracy < 0.1m/s (within +/- 15% error)
Hot start <1s
Warm start < 25 s
Cold start < 35 s2
CELLULAR
Technology GSM
Quad-band 850 / 900 / 1800 / 1900
2G bands
MHz
2
Expected time in conditions with good GNSS satellites visibility
11 FMB910 | Wiki
GPRS Multi-Slot Class 12 (up to 240 Weight 69 g
Data transfer
kbps), GPRS Mobile Station Class B
OPERATING ENVIRONMENT
Data support SMS (text/data)
Operating temperature (without
POWER -40 °C to +85 °C
battery)
Input voltage range 6-30 V DC with overvoltage protection Storage temperature (without battery) -40 °C to +85 °C
Back-up battery 170 mAh Li-Ion battery 3.7 V (0.63 Wh) Operating humidity 5% to 95% non-condensing
12 FMB910 | Wiki
Electrical characteristics
Table 5 Electrical characteristics
ANALOG INPUT
VALUE Input voltage (Recommended Operating
CHARACTERISTIC DESCRIPTION 0 +30 V
Conditions)
MIN. TYP. MAX. UNIT
SUPPLY VOLTAGE Input resistance 150 kΩ
13 FMB910 | Wiki
Safety information All wireless data transferring devices produce
interference that may affect other devices which are
placed nearby.
This message contains information on how to operate FMB910 safely. By
following these requirements and recommendations, you will avoid The device must be connected only by qualified
dangerous situations. You must read these instructions carefully and personnel.
follow them strictly before operating the device!
The device must be firmly fastened in a predefined
• The device uses SELV limited power source. The nominal voltage is
location.
+12 V DC. The allowed voltage range is +6 ... +30 V DC.
• To avoid mechanical damage, it is advised to transport the device in
an impact-proof package. Before usage, the device should be placed The programming must be performed using a PC
so that its LED indicators are visible. They show the status of device with autonomic power supply.
operation. Installation and/or handling during a lightning storm
• When connecting the (1x5) cables to the vehicle, the appropriate is prohibited.
jumpers of the vehicle power supply should be disconnected.
• Before dismounting the device from the vehicle, the 1x5 connection
The device is susceptible to water and humidity.
must be disconnected.
• The device is designed to be mounted in a zone of limited access,
which is inaccessible to the operator. All related devices must meet Risk of explosion if battery is replaced by an incorrect
the requirements of EN 62368-1 standard. type. Dispose of used batteries according to the
• The device FMB910 is not designed as a navigational device for boats. instructions.
Do not disassemble the device. If the device is Battery should not be disposed of with general
damaged, the power supply cables are not isolated or household waste. Bring damaged or worn-out
the isolation is damaged, DO NOT touch the device batteries to your local recycling center or dispose
before unplugging the power supply. them to battery recycle bin found in stores.
14 FMB910 | Wiki
Certification and Approvals Para maiores informações, consulte o site da
ANATEL www.anatel.gov.br
Este equipamento não tem direito à proteção
• FMB910 ANATEL
contra interferência prejudicial e não pode
• FMB910 CE / RED
causar interferência em sistemas devidamente
• FMB910 E-Mark
autorizados.
• FMB910 EAC
• FMB910 RoHS
00647‐20‐08591
• FMB910 REACH For more information, see the ANATEL website
• FMB910 Declaration of IMEI assignment www.anatel.gov.br
This equipment is not entitled to protection
This sign on the package means that it is
against harmful interference and must not
necessary to read the User‘s Manual before
cause interference in duly authorized systems.
your start using the device. Full User‘s Manual
version can be found in our Wiki.
15 FMB910 | Wiki
Warranty Warranty Disclaimer
TELTONIKA guarantees its products to be free of any TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS
manufacturing defects for a period of 24 months. With additional WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS THE
agreement we can agree on a different warranty period, for more LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED
detailed information please contact our sales manager. WARRANTIES NULL AND VOID AND SAME ARE HEREBY EXCLUDED.
ALSO EXCLUDED FROM THIS LIMITED WARRANTY ARE ANY AND
Contact us teltonika-gps.com/about-us/contacts/
ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT
All batteries carry a reduced 6 month warranty period. NOT LIMITED TO, LOSS OF USE OR REVENUE, LOSS OF TIME,
INCONVENIENCE OR ANY OTHER ECONOMIC LOSS.
If a product should fail within this specific warranty time, the
product can be: More information can be found at teltonika-gps.com/warranty-
repair/
• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fulfilling the same
functionality
• TELTONIKA can also repair products that are out of warranty at
an agreed cost.
16 FMB910 | Wiki