Professional Documents
Culture Documents
RVM 1535 MM 1 Sa
RVM 1535 MM 1 Sa
RVM 1535 MM 1 Sa
IIIIIIIIIIIIIIIIIIIIII CZ]
I
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Damage--Shipment/Installation .............................. 6
Installing the
Charcoal Filter Accessory .................... 22
Parts Included. ......................................... 6
Before You Use Your Microwave .......................... 23
Tools You Will Need ............................................... 7
2
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
3
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
HOOD EXHAUST
NOTE: Read these next two pages only if you plml to vent your exhaust to the
outside. If you plan to recirculate the air back into the room, proceed to page 6.
(1) 24 Ft.
(1) 5 Ft.
TransitionAdaptor*
Rectangular-to-Round 5 Ft. x
* IMPORTANT: If a rectangula>to-round transition adaptor is used, the bottom cornei_ of the damper
will haxe to be cut to fit, using the tin snips, in order to allow free moxement of the damper.
(2) = 20 R.
(_ 90° Elbow 10 Ft. x
4
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
NOTE: If you need to install ducts, note that the total Maximum duct length:
duct length of 3V{' x 10" rectangular or 6" diameter For s;Kisfhctorv air movement, the total duct length of
round duct should not exceed 140 equivalent feet. 3¼" x l 0" rectangular or 6" diameter round duct should
Outside ventilation requires a HOOD EXHAUST DUCT. not exceed 140 equivalent feet.
Read the following carefiflly.
Elbows, transitions, wall and roof caps,
NOTE: It is important that venting be installed using
etc., present additional resistance to airflow and are
the most direct route and with as tew elbows as possible.
equi\_dent to a section of straight duct which is longer
This ensures clear venting of exhaust and helps prevent
than their actual physical size. When calculating the total
blockages, Also, make sure dmnpers swing freely and
duct length, add the equi\:dent lengths of all transitions
nothing is blocking the ducts.
and adaptors plus the length of all straight duct sections.
Exhaust connection: The chart below shows you how to calculate total
equi\_dent ductwork length using the approximate feet
The hood exhaust has been designed to mate with
of equivalent length of some typical ducts.
a standard 3V{' x 10" rectangular duct.
If a round duct is required, a rectangula_to-round
transition adaptor m list be used. Do not use less than
a 6" diameter duct.
adaptor is us(d, th( bottom corners of th( (lamp( 1 and rel]( (t re(ltfir( m( nls for good v( riling performan(( x_ith
_ill have to b( cm to fit, using th( lin snips, in ord(l any vent hood.
* IMPORTANT:
to allm_ free If a r( ( tangulal_to-round
lllOVelllelll of Ihe dHlllpel, transilion Equival( nl I( ngths o[ du(t piec( s are |)as( d on aclual lests
5
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
j Screws(W'-28x 3Y/')
NylonGrommet
(for metalcabinets) 2
ADDITIONAL PARTS
PART QUANTITY
TopCabinet 1
TOP CABINET TEMPLATE Template
RearWall
Template
REAR
WALL
TEMPLATE
Installation
r Instructions
INSTRUCTIONS
Separately
Packed
Grease
Filter
Separately
Packed
Exhaust
Adaptor
6
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
(optional)
cabinet installationsonly)
Gloves for top cabinetspacing
(usedon recessedbottom
Saw(saber,hole or keyhole)
Studfinder or Hammer(optional)
__"__-''-_'-'- Ductandmaskingtape
Safetygoggles Level
MOUNTING SPACE
NOTES:
BottomEdgeof
CabinetNeedsto • The space between the cabinets must be
30" wide and fl'ee of obstructions.
be 30" or More
from the Cooking • If the space between the cabinets is greater
Surface than 30", a Filler Panel Kit may be used to fill
in the gap between the microwave oven and
the cabinets. Yore" Owner's Manual contains
the kit nmnber tin" wmr model.
Backsplash • This microwave oven is fl_r installation over
ranges up to 36" wide.
66" or More • When installing the microwave oven beneath
from the Floor smooth, fiat cabinets, be careful to follow the
to the Topof instructions on the top cabinet template for
the Microwave
power cord clearmlce.
7
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
8
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
Trimthe rearwall
template along
the dotted line.
II
Trimthe rearwall ...........
I)raw a verticalline on the wall at
the centerof the 30" to 36" wide templatealong
the dotted line.
space.Tapethe RearWall Template
onto the wall matching the
centerline andtouchingthe bottom
of the cabinet.
Drawa vertical line on the wall at
the centerof the 30" or 36" space.
Template aligned with front overhang Tapethe RearWall Templateonto
on cabinet bottom the wall matchingthe centerlineand
touchingthe bottomcabinetframe.
9
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
° o o o o o o o o o o o o o o o o o o o o o o o o o o
_lJse a level to check that the template is positioned _ Drill holes in the ulai'ked locations. If there is a stud,
a cct _I'_telv, drill a _(; hole fo_ wood screws. For holes that don't
_ I,ocate and mark at least one stud on the lefi or right line up with a stud, drill a :'A" hole tot toggle bolts.
side of the centerline. It is important to use at least one NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
wood screw mounted firmly in a stud to supl)ort the
weight of the microwave.
Mark three additional, evenly spaced locations for the
supplied toggle bolts.
10
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
This microwave oven is designed fi>r adaptation to NOTE: This microwave is shiI)ped assembled fl>r Outside
the following three types of ventilation: Top Exhaust (except fl)r non-vented models). Select the
A, Outside Top Exhaust (Vertical Duct) type of ventilation required for wmr installation and
proceed to that section,
B, Outside Back I_haust (Horizontal Duct)
_-_ RECIRCULATING
(NON-VENTED DUCTLESS)
11
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to _Mfll
A2. Prepare Top Cabinet
A3. Check Damper Operation
A4. Mount Microwave Oven
A5. Ac!j ust Exha ust Adaptor
A6. (_onnect Ductwork
ml,
B01tEnd
12
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
CABINET
The top cabinet template will help you locate the top
Reinstallrear
SUl)port screw holes, power cord and exhaust outlet
locations. retainingscrew
" Slide the exhaust adaptor toward the left side and
into the opening,
" The adaptor should be oriented as shown,
_ Rotate front of o_en
up against cabinet
bottoill.
13
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
Filler Block
For Fr0nt-t0-Backor
to Depth Side-to-SideAdjustment,
of Cabinet
__Equivalent Slidethe Exhaust
Recess Adaptoras Needed
Self-AligningScrew
each screw.
S
Tighten
center
scFew
completely.
[] Tighten tile outer two screws to tile top of tile _ Extend tile house duct down to connect to
tile exhaust adaptor.
microwave oxen. (¥\ hile tightening screws, hold
tile microwaxe oxen in place against tile wall and [] Seal exhaust duct joints using duct tape.
the top cabinet.)
/,
_ Install grease filter: See tile Owner's Manual
packed with tile microwave.
4
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
INSTALLATION OVERVIEW
B1. Prepare Rear _4_dl
B2. Remove Exhaust Adaptor
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
BS. Adapt Blower for Back Exhaust
B6. Motmt the Microwave Oven
TEMP LATE . .........
15
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
Tile top cabinet template will hel I) you locate tile top
stlI)I)oFt scI'ew holes and poweI" coi'd Ctltotlt.
Spacingfor TogglesMore
-,,-I-,H,-i-,,_ThanWall Thickness ADAPTING MICROWAVE
BLOWER FOR OUTSIDE
i
ToggleWings
Mounting
Plate BACK EXHAUST
,,i,( [] ReIllOXe tile back top center blower illotoi" dooI"
retaining screw.
J
B01tEnd of
BlowerMotor_ _.Microwave
_ Place tile motmting plate against tile wall and
insert the toggle wings into the holes in the wall
to I//Otlnt tile plate.
NOTE: Betm'e tightening the toggle bolts and the BlowerDoor
wood screw(s), check again to be sure that the Screw
motmting plate is level and centered left to right. _Open tile blower door b} lifting it /l I) at tile back
CAUTION: Be careflfl to awfid pinching fingers side of the microwaxe. Remo_e and saxe the top
between the back of the motmting plate and the wall. and back retaining screws that hold the blower
iilotoi" ill tile iilici'owa_e.
_ Tighten all bolts. Pull the plate away fl'om the
wall to hel I) tighten the bolts. Be carefld not to
Retaining
ove_=torque the toggle bolts. screw
Retaining
screw
16
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
ADAPTING MICROWAVE ] Tilt and place the blower trait back into the
oi_ening, in the top of the microwave.
BLOWER FOR OUTSIDE
BACK EXHAUST (cont.)
Black Guide
Exhaust BlowerMotor Screw
Outlet
Guide LockingTabs
17
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
CabinetFront
MOUNT THE MICROWAVE CabinetBottomShelf
OVEN FillerBlock
to Depth
T ofquivalent
Cabinet
Recess
Self-AligningScrew
FOR EASIER INSTAI,IATION AND PERSONAI,
MicrowaveOvenTop
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
[] Insert 2 selt:aligning screws
NOTE: If vour cabinet is metal, use tile nylon
through outer top cabinet
grolmnet around tile power cord hole to prevent holes. Ttu'n two flfll ttli'ns
cutting of tile cord. on each screw,
18
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
RECIRCULATING (Non-VentedDuctless)
INSTALLATION OVERVIEW
C1. Attach Mom_ting Plate to _Mdl
C2. Prepare Top Cabinet
C3. Check Microwave Assemblv
C4. Adapt Blower tin" Recirculation
C5, Mount the Microwave Oven
C6, Install Charcoal Filter
J
Blower Motor-- Back of
Microwave
Blower Door
Screw Backof
Microwave
[]Open the blower door b) lifting it up at the back
side of the microwaxe. Remo_e and saxe the top
and back retaining screws that hold the blower
_ Remoxe the two screws holding the gra) colored
illotor in the illiCi'OWa_,e.
inlet sleeve to the blower unit. Rotate the ora_
sleeve as shown tmtil the gra) arrow lines up with
Retaining the "R', Recirculating exhaust. Reinstall the two
screw scYews.
x__"
Retaining
screw
Back of Microwave
Black
Exhaust
Outlet Facing
the Front
Must Face
Downward Backof
Microwave
2O
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
i_oEquivalent to Depth
Self-AligningScrew
MicrowaveOvenTop
21
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
[]Insert 2 self-aligning screws []Remove tile 3 screws along tile top fl'ont edge
throuoh_ outer top cabinet of tile oven using a #1 Phillips screwdriver.
holes. TtlI'n two fllll ttlI'IlS on _] Open tile door.
each screw.
_ Remove the grille by sliding it to the left and then
pulling it straight off.
Charcoal
_J_ Filter
[]Tighten center
screw completel). _ Install tile charcoal filter. Tile filter will rest at
an angle on two side support tabs. X,_hen properl,_
[] Tighten tile outer two screws to tile top of tile
installed, the wire mesh of the filter should be
microwave oven. (While tightening screws, hold
xisible from the front.
tile microwave oven in place against tile wall and
tile top cabinet.) ILL_
Insertmesh-sideup
22
Downloaded from www.Manualslib.com manuals search engine
Installation Instructions
-_] Make
installedsureaccording
the microwaxe oxen has been
to instructions. _ Read the Owner's Manual.
[_ KEEP THE
FOR INSTAI,I,ATION INSTI_.UCTIONS
I_OCAL INSPECTOR'S USE.
'27] Remoxe all )ackino
IlliC I'OW_lX, e ox, en.
material from the
IllIIIIIIII
Ensure proper
ground exists /
before use
23
Downloaded from www.Manualslib.com manuals search engine
Printed in Malaysia
39-40425 ]
10-04JR [ DE68-02957A J