Professional Documents
Culture Documents
DSC S650
DSC S650
SERVICE MANUAL
Ver. 1.2 2007.06
US Model
Canadian Model
Revision History
AEP Model
UK Model
How to use
Acrobat Reader
E Model
Australian Model
Hong Kong Model
Internal memory
ON BOARD
Chinese Model
Korea Model
Brazilian Model
Tourist Model
Link
In case of the lens assembly, main board, or main frame assembly failure,
contact your local Sony Service Headquarter for the measures.
2007F0800-1
DSC-S650 © 2007.06
9-852-182-11 Sony EMCS Co. Published by Kohda TEC
SPECIFICATIONS
DSC-S650
—2—
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point : LEAD FREE MARK
them out to the customer and recommend their replacement. Unleaded solder has the following characteristics.
4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than
of deterioration. Point them out to the customer and ordinary solder.
recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified.
Soldering irons using a temperature regulator should be set to
6. FLEXIBLE Circuit Board Repairing about 350°C.
• Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
• Do not touch the soldering iron on the same conductor of the • Strong viscosity
circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than
• Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such
or unsoldering. as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
DSC-S650
—3—
TABLE OF CONTENTS
Section Title Page
1. SERVICE NOTE
1-1. Process After Fixing Flash Error ····································· 1-1
1-2. Method for Copying or Erasing the Data in Internal
Memory ··········································································· 1-1
2. DISASSEMBLY
2-1. Disassembly ····································································· 2-1
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram ··················································· 3-1
3-2. Power Block Diagram ····················································· 3-2
DSC-S650
—4—
1. SERVICE NOTE
1-1. PROCESS AFTER FIXING FLASH ERROR
Method for Initializing the Flash Error
Initialize
Note: When replacing the camera, erase the data in internal memory of the board before replacement.
Copy
• Use batteries with enough capacity or the AC Adaptor (not supplied). If you attempt to copy image files
using batteries with little remaining charge, the batteries may run out, causing copying to fail or possibly
corrupting the data.
• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in
(Internal Memory Tool) (page 48).
• When you copy the data in the internal Memory to the “Memory Stick Duo”, all the data will be copied.
You cannot choose a specific folder on the “Memory Stick Duo” as the destination for the data to be
copied.
• Even if you copy data, a (Print order) mark is not copied.
Format
DSC-S650
1-1
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
5 1
2 1
Front Section
(See Page 2-2)
4
1 3
1
2
1
1 Screw TP1.4 × 2.5
2 Frame, SW
3 SW Board, Complete
DSC-S650
2-1
Ver 1.1 2007.02
2. DISASSEMBLY
(From 2-1 Page) 5
4
1
1
2
1
3 Shorting jig
(1k Ω / 1W)
1
Caution
1 3
2
1 Screw TP1.4 × 3
1 Screw TP1.7 × 3
2 Screw TP1.4 × 2.5
2 LCD Block Assy
3 Screw TP1.7 × 16
3 1
4
1
2 3 2
2
1 Lens Assy
2 Screw TP1.4 × 3 1
1 Screw TP1.7 × 3 4
3 Strap Bracket 2
2 Screw TP1.4 × 2.5
4 Screw TP1.4 × 2.5
3 ST Board, Complete
5 Battery Cover 6
4 Screw TP1.7 × 3 4
6 Main Frame Assy 5
4
DSC-S650
2-2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM
LCD DSP
CDS
+5VM
+5VM +3.3V PXCLK
LCD 2.0 +3.3V
LCD_EN
PXCLK
HD
HD
VD
PXCLK
HD
INCH LCD_EN
LCD_MCLK
LCD_MCLK
LCD_VD
LCD_EN
LCD_MCLK CDS_EN
VD CDS_EN
SCLK
VD
CDS_EN +3.3V
+3.3V
PANEL
LCD_VD LCD_HD LCD_VD SCLK SDATA SCLK -7.5V
LCD_HD LCD_SCLK LCD_HD SDATA AFERST SDATA -7.5V
LCD_SCLK LCD_SDATA LCD_SCLK AFERST TG_EN AFERST +13.4V
LCD_SDATA LCD[0..7] LCD_SDATA TG_EN VSUB_Con1 TG_EN +13.4V
LCD[0..7] MLCD_ON LCD[0..7] VSUB_Con1 VSUB_Con2 VSUB_Con1 DGND
MLCD_ON BL MLCD_ON VSUB_Con2 CCD_ON VSUB_Con2 DGND
LCD_BACKLIGHT BL BL CCD_ON CCD_ON
TG_ON
DGND TG_ON CDS_ON TG_ON
DGND CDS_ON CCD[0..11] CDS_ON
1 2
RED CCD[0..11] CCD[0..11]
LCD
CDS
2 1
MEMORY
DDR DGND
+3.1VD DGND
MS_ON +3.1VD
MS_ON R/B MS_ON
RAMD[0..15] R/B MS_INS# R/B
RAMD[0..15] RAMA[0..14] RAMD[0..15] MS_INS# CLE MS_INS#
RAMA[0..14] RAMLDM RAMA[0..14] CLE WE CLE
+2.5VD RAMLDM RAMWE_N RAMLDM WE WP WE
+2.5VD RAMWE_N RAMCAS RAMWE_N WP ALE WP
RAMCAS RAMRAS RAMCAS ALE CE0 ALE
DGND RAMRAS RAMCS_N RAMRAS CE0 RE CE0
DGND RAMCS_N RAMLDQS RAMCS_N RE MS_CLK RE
RAMLDQS RAMUDQS RAMLDQS MS_CLK MD[0..7] MS_CLK
RAMUDQS RAMUDM RAMUDQS MD[0..7] FA23 MD[0..7]
RAMUDM RAMCLK_N RAMUDM FA23 FA20 FA23
VP RAMCLK_N RAMCLK RAMCLK_N FA20 FA22 FA20
2 4 1 2
P1,P2
RAMCLK RAMCLK_EN RAMCLK FA22 FA21 FA22
STROBE_Chg RAMCLK_EN RAMREF RAMCLK_EN FA21 UGND2 FA21
STROBE_Trg
1 S NC
RAMREF RAMREF UGND2
Charge_c +13.4V
FLASH_RDY 3
MEMORY
DDR
1 3 BEEPER
BEEPER
ST_LED
LENS
1 2
GREEN ZOOM SENSOR
+3.1VD
2
LENS
PWR_ON
PWR_ON PWRKEY
PWRKEY BAT_LOAD
BAT_LOAD JACK
D+ +13.6V
D+ D- D+ +13.6V
D- USB_DET D- +3.1VD
SW USB_DET USB_DET +3.1VD
PC
AV_DET
+3.1VD STA_LED AV_DET VIDEO_OUT A/V_DET DGND
1 2
+3.1VD STA_LED STA_LED VIDEO_OUT LINE_OUT VIDEO_OUT DGND
GREEN
DGND LINE_OUT BEEPER LINE_OUT UGND
DGND SW_KEY_ADC BEEPER BEEPER UGND
UGND2 SW_KEY_ADC SW_KEY_ADC
UGND2
JACK
SW
2
5
2 1
SW_PLAYBACK
SW_PLAYBACK
2
5
POWER
4
6
CCD_ON1 SW_WIDE
2
5
VP CCD_ON1 CCD_ON1 SW_WIDE
VP PWR_CTRL TOP
4
6
-7.5V PWR_CTRL PWR_CTRL SW_TELE
-7.5V VP SW_TELE PWR_KEY
4
6
+2.5VD VP MODE_R5 PWR_KEY
+2.5VD +1.8VD MODE_R5 MODE_R4 MODE_R5
1 2
+3.3V +1.8VD MODE_R4 MODE_R4
GREEN
+3.3V +3.1VD MODE_R2
+3.1VD +3.1VD MODE_R2 MODE_R1 MODE_R2
+3.1VD +3.3VS MODE_R1 MODE_R0 MODE_R1
+5VM +3.3VS MODE_R0 SHUT1 MODE_R0
+5VM +3.3V SHUT1 SHUT2 SHUT1
+13.4V CCD_ON +3.3V SHUT2 PW_LED SHUT2 MODE_R0 ~R5
+13.4V CCD_ON +2.5VD PW_LED DGND PW_LED
+2.5VD DGND
MIC_N
DGND
1
4
4
2
3
Power
1 3
Out GND_3
2
GND_2
BATT+1
Q17 MIC1
1 8 SPM0204HD5
4 5 MIC4_4.72X3.76_173
2 7 G2412-0039-00
3 6
1000PK_25V_X7R
1
1
0.1UK_16V_X5R
AO8803
1000PK_25V_X7R
1 2 G2013-0081-00
SOP8_0.65_9
1 2
1 2
1
F1 BATT- 1
1.6A/32V R131
*10K
G2112-1002-00
2
R0402
1 2
F2
0.8A/24V
DSC-S650
3-1
3. BLOCK DIAGRAMS
3-2. POWER BLOCK DIAGRAM
BATT+
BATT-
+13.4V
MCU BOARD
Q17
1 8
4 5
2 7
3 6
F1
1.6A/32V AO8803
STROBE BOARD 1 2 G2013-0081-00
SOP8_0.65_9 +5VM
4 2 FLASH_VP 1 2
1
CCD BOARD
P1,P2
NC S 1 F2 R131
VDD 0.8A/24V *10K
3 G2112-1002-00
2
1
1
2
3 1
2
U2 BUFFER
2
22UF 0.1UF
1
Q2 +13.4V +13V_CCD VCC
+5VM 10UF X 4 0.01UF X 7 1000PF X 3
1
VCC IN
2
1
2.2UK 0.01UK 2.2UK 2.2UK 1000PF
2
1UF 10UK 4.7UK 0.01UK
2
+1.8VD 0.1UF
2
2
2
1
2
2
VDD
22UF 0.1UF -7.5V -7.5V_CCD
1 2 VL
1
BULE +3.1VD
1
0.01UK
2
4.7UK U1
2
10UF 0.1UF
2
+5VM +3.3V
1
2
2
22UF
TOP BOARD 22UF
1
1 2
BULE +13V_VD VH
+3.1VD +3.1VD
1
2
4.7UK 0.1UK
+3.1VD 22UF
2
PVCC +5VM
1
1
VCC -7.5V_VD VL
1
1
VM1 47UF 0.1UF X 4 C107 PVDD DVDD AVDD
#4.7UK_25V 0.1UK
2
VM2
2
VM3
2
1
1
2
1
ZPIV
10UF X 2 1000PF X 2 0.1UF X 2
2
2
+3.3V +3.1V
ZPRCO
LCD 2.0 INCH
2
PANEL
1UF
VDDPWR VDDDDR VDDPLL 0.01UF X 4
1
VDDUSBPLL +3.1VD
VDDCORE VDDP
1
1
VDDDAC 1000PF X 2
VDDUSB +3.3V +3.1V CDS
VDDSPKR 10UF X 2 0.1UF X 2
2
VDDADC 2
2
VDDAUO
1UF 0.1UF
LED anode
1
U11
+3.3V +3.1VL
1
PVDD
0.1UF 4.7UF AVDD
LDO VCC
2
+3.3V +3.1V LCD_BACKLIGHT
2
1UF FB 1 2
RED
1
+3.1VD VCC
3
10UF 0.1UF X 2 BL 1 2 2 Q12
1 1
*1K
2
*3.3K
Q13
1
+3.1VD VCC2 *27.4
SW
2
1
1
2 10UF 0.1UF X 2
SW BOARD
+3.1VD
1 2
BULE
DSC-S650
3-2
Ver. 1.2 2007.06
Rear Block
(See page 4-3.)
4
4
11 13
1
13
4 3 13
12
14
1 13 5
13
Main Frame Block
(See page 4-2.) 3
8
9 (Note 1)
2 6
10
7
5
Ref. No. Part No. Description Ref. No. Part No. Description
1 3-113-001-01 SCREW TP1.4*2.5 8 A-1249-952-A LCD BLOCK ASSY (Note1)
2 3-113-005-01 SCREW TP1.7*3 9 3-106-991-01 MIDDLE COVER (RIGHT)
3 3-209-039-01 SCREW TP1.7*16 10 X-2177-476-1 CABINET (FRONT) ASSY
4 3-113-002-01 SCREW TP1.4*3 11 A-1249-951-A CABINET (UPPER) BLOCK ASSY
5 3-273-595-01 SCREW TP1.7*4.5 12 X-2177-477-1 MIDDLE COVER (LEFT) ASSY
DSC-S650
4-1
4. REPAIR PARTS LIST
4-1-2. FRONT BLOCK
ns: not supplied
55
53
53
52 (Note 2) 53
53
51
55
53
54
54
54
ns
(Note 1) ns
(Note 1)
ns
(Note 1)
DSC-S650
4-2
4. REPAIR PARTS LIST
4-1-3. MAIN FRAME BLOCK
104
101
101
103
101 102
101
DSC-S650
4-3
Ver. 1.2 2007.06
USB cable
3-196-981-01
GB
DSC-S650
Operating Instructions
Before operating the unit, please read this manual thoroughly, and retain it for future reference.
Owner’s Record
The model and serial numbers are located on the bottom. Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this product.
Model No. DSC-S650
Serial No. ___________________________
2-050-981-01
Instruction Manual
2-897-955-12 (ENGLISH) (CND, AEP, UK, E, HK, AUS, JE)
2-897-955-22 (FRENCH, ITALIAN) (AEP, CND)
2-897-955-32 (SPANISH, PORTUGUESE) (AEP, E)
2-897-955-42 (GERMAN, DUTCH) (AEP)
2-897-955-52 (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, CH, HK)
CD-ROM 2-897-955-62 (RUSSIAN) (AEP)
(Cyber-shot Application Software, 2-897-955-72 (ARABIC, PERSIAN) (E)
handbook “Cyber-shot Handbook”) 2-897-955-82 (KOREAN) (KR, JE)
2-897-942-01 (EXCEPT US) 2-897-955-92 (CZECH, POLISH) (AEP)
2-897-943-01 (US) 2-897-956-12 (HUNGARIAN, SLOVAK) (AEP)
2-897-956-22 (SWEDISH, FINNISH) (AEP)
2-897-956-32 (DANISH, NORWEGIAN) (AEP)
2-897-956-42 (THAI, MALAYSIAN) (E)
2-897-956-52 (TURKISH, GREEK) (AEP)
2-897-956-62 (ENGLISH, SPANISH) (US)
CLICK!
Table of contents
Basic Operations
Troubleshooting
Others
Index
DSC-S650
4-4
[Regarding Fuse]
• MCU BOARD
Ref. No : F1
MANUFACTURER: KAMAYA ELECTRIC CO.,LTD.
TYPE: FCC16 162AD
RATING: 1.6A
Ref. No : F2
MANUFACTURER: KAMAYA ELECTRIC CO.,LTD.
TYPE: FCC10 801AD
RATING: 800mA
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar
Finding a text
1. Click the Find button . Moving with link
2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary) 1. Select either palm tool , zoom tool , text selection tool
, or graphic selection tool .
Application to the Service Manual: 2. Place the pointer in the position in a text where the link exists
To execute “find” from current page toward the previous pages, (such as a button on cover and the table of contents page, or
select the check box “Find Backward” and then click the blue characters on the removal flowchart page or drawing
“Find”. page), and the pointer will change to the forefinger form .
3. Then, click the link. (You will go to the link destination.)
Switching a page
• To move to the first page, click the .
• To move to the last page, click the . “Rotate”
• To move to the previous page, click the . • Click rotate tool , and the page then rotates 90 degrees each.
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2007.01 Official Release — —
1.1 2007.02 Correction-1 • Correction of DISASSEMBLY Yes
(C1) S.M. Correction : Page 2-2
1.2 2007.06 Correction-2 • Correction of EXPLODED VIEWS Yes
(C2) • Change of part number for Instruction
Manual
S.M. Correction : Page 4-1, 4-4
DSC-S650