Professional Documents
Culture Documents
DTC U0028 - 87 (Advanced Keyless Entry and Push Button Start System)
DTC U0028 - 87 (Advanced Keyless Entry and Push Button Start System)
U0028:87 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START SYSTEM]
DTC U0028:87 [ADVANCED KEYLESS ENTRY AND PUSH BUTTON START
SYSTEM]
id09021c399500
DESCRIPTION Communication error with BCM
• Keyless control module receives the erratic signal from BCM.
DETECTION CONDITION
• Keyless control module cannot receive the signal from BCM.
• BCM DTC is stored
• BCM connector or terminals malfunction
• Keyless control module connector or terminals malfunction
• Short to ground in wiring harness between the following terminals:
― BCM terminal 4K—Keyless control module terminal 3X
• Short to power supply in wiring harness between the following terminals:
POSSIBLE CAUSE
― BCM terminal 4K—Keyless control module terminal 3X
• Open circuit in wiring harness between the following terminals:
― BCM terminal 4K—Keyless control module terminal 3X
• BCM malfunction
• Keyless control module malfunction
Diagnostic Procedure
― BCM terminal 4K No Go to the next step.
• Is there any voltage?
INSPECT COMMUNICATION CIRCUIT FOR OPEN CIRCUIT
• BCM and keyless control module connectors are disconnected. Yes Go to the next step.
• Switch the ignition to off.
• Disconnect the negative battery cable.
• Inspect for continuity between the following terminals (wiring
6 harnessside):
No Repair or replace the wiring harness for a possible open
― BCM terminal 4K—Keyless control module terminal 3X circuit, then go to Step 8.
• Is there continuity?
VERIFY BCM MALFUNCTION
• Make sure to reconnect the disconnected connectors.
• Reconnect the negative battery cable.
(See BATTERY REMOVAL/INSTALLATION [MZR 1.5, MZR 1.6].)
(See BATTERY REMOVAL/INSTALLATION [MZR 2.0, MZR 2.5].)
(See BATTERY REMOVAL/INSTALLATION [MZR 2.0 DISI istop].) Replace the BCM, then go to the next step.
(See BATTERY REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].) (See BODY CONTROL MODULE (BCM)
(See BATTERY REMOVAL/INSTALLATION [MZRCD 2.2].) Yes REMOVAL/INSTALLATION [L.H.D.].)
(See BATTERY REMOVAL/INSTALLATION [SKYACTIVG 2.0].) (See BODY CONTROL MODULE (BCM)
7 • Operate the advanced key to activate the keyless control module. REMOVAL/INSTALLATION [R.H.D.].)
• Clear the DTC from the keyless control module using the MMDS.
(See CLEARING DTC [ADVANCED KEYLESS ENTRY AND PUSH
BUTTON START SYSTEM].)
• Operate the advanced key to activate the keyless control module.
• Perform the advanced keyless entry and push button start system
DTC inspection using the MMDS.
(See DTC INSPECTION [ADVANCED KEYLESS ENTRY AND PUSH
BUTTON START SYSTEM].) No Go to Step 9.
• Is the same DTC present?
VERIFY TROUBLESHOOTING COMPLETED
• Make sure to reconnect the disconnected connectors.
• Reconnect the negative battery cable.
(See BATTERY REMOVAL/INSTALLATION [MZR 1.5, MZR 1.6].)
(See BATTERY REMOVAL/INSTALLATION [MZR 2.0, MZR 2.5].)
(See BATTERY REMOVAL/INSTALLATION [MZR 2.0 DISI istop].) Replace the keyless control module, then go to the next step.
(See BATTERY REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].) Yes (See KEYLESS CONTROL MODULE
(See BATTERY REMOVAL/INSTALLATION [MZRCD 2.2].) REMOVAL/INSTALLATION.)
(See BATTERY REMOVAL/INSTALLATION [SKYACTIVG 2.0].)
8 • Operate the advanced key to activate the keyless control module.
• Clear the DTC from the keyless control module using the MMDS.
(See CLEARING DTC [ADVANCED KEYLESS ENTRY AND PUSH
BUTTON START SYSTEM].)
• Operate the advanced key to activate the keyless control module.
• Perform the advanced keyless entry and push button start system
DTC inspection using the MMDS.
(See DTC INSPECTION [ADVANCED KEYLESS ENTRY AND PUSH No Go to the next step.
BUTTON START SYSTEM].)
• Is the same DTC present?
Go to the applicable DTC inspection.
VERIFY THAT NO OTHER DTCs ARE PRESENT Yes (See DTC TABLE [ADVANCED KEYLESS ENTRY AND
9 PUSH BUTTON START SYSTEM].)
• Are any DTCs present?
No DTC troubleshooting completed.
https://euroesi.mazda.co.jp/esicont/eu_eng/mazda3/20110724140058/html/id09021c399500.html 2/2