Professional Documents
Culture Documents
Especificaciones de Producto - MFR, MFS y MFX
Especificaciones de Producto - MFR, MFS y MFX
609.6 mm
Minimum Recommended
24"
Clearances*
PRODUCT SPECIFICATIONS
• Motor: (Two-speed)
415 mm
16.33"
Wash: .19 Hp (0.1 Kw), Extract: 0.75 Hp (.55 Kw). 2" 2"
51 mm 50 mm
• Maximum amperage draw Positioning of Machines
Single Phase - 10 amps 120 V
(except for motor starting surges) TOP VIEW
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR18 (ALL MODELS) 07/02 3-1
WATER CONSUMPTION GALLONS - 18 LB. LOADS TOTAL
MFR18 MC & PD PREWASH* WASH RINSE 1 RINSE 2 RINSE 3* TOTAL GALLONS
WHITE HOT 4.8 7.4 - - - 12.2 -
(PROGRAM 1) COLD 4.8 - 6.9 8.7 8.7 29 41.2
COLORS HOT 4.8 4.8 - - - 9.5 -
(PROGRAM 2) COLD 4.8 2.6 6.9 8.7 8.7 31.7 41.2
BRIGHT COLORS HOT - - - - - - -
(PROGRAM 3) COLD 9.5 7.4 6.9 8.7 8.7 41.2 41.2
PERM. PRESS HOT - 4.8 - - - 4.8 -
(PROGRAM 4) COLD - 4.8 6.9 8.7 8.7 29.1 33.9
DELICATES & KNITS HOT - 4.8 - - - 4.8 -
(PROGRAM 5) COLD - 4.8 6.9 8.7 8.7 29.1 33.9
WOOLENS HOT - - - - - - -
(P6) PD model only COLD - 9.5 6.9 8.7 8.7 33.8 33.9
* Optional on select models. PD cycle time 11.5 - 60.5 min. (plus fills)
PD models are generation 2 debit card ready
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR18 (ALL MODELS) 07/02 3-2
ELECTRICAL REQUIREMENTS
• 120 volts, single phase, 60 Hz, 20 amp circuit breaker, minimum wiring size awg. 12 of copper
wire only.
OR
• 208 / 240 volt, three phase, 60 Hz, 20 amp circuit breaker, minimum wiring size awg. 12 of
copper wire only.
• Individual branch circuits serving only the washer recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
WATER REQUIREMENTS
Water Connection Data
Model Water Valve Recommended Functioning Capacity at
Connection Water Pressure Limits 3 Bar or 40 psi
Inch psi bar psi bar gpm lit/m
MFR18 3/4" 30-85 2-6 30-120 2-8 11.6 44
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR18 (ALL MODELS) 07/02 3-3
FLOORING/MOUNTING REQUIREMENTS
Bolt should protrude 2 1/8" minimum out INSTALLATION OF MACHINE ANCHOR BOLTS
ANCHOR of cement pad plus grout thickness. DRAIN OPENING IN
GROUT FULL
BOLT SIZE WIDTH OF FRAME REAR OF BASE
3/8" - 1/2" FRAME GROUTING
BASE FRAME
inch mm NON SHRINK
COMPACTED
FILL DIRT
26"
66 cm
6 1/2"
16.5 cm
CABINET
OUTLINE
3 9/16"
9.0 cm
OVERHEAD VIEW
24 1/4" NOTE: 16007698 TYVEK Template
61.5 cm available through repair parts sources.
10 13/16"
27.5 cm
3 5/8"
8.5 cm
FRONT
NOTES:
1. This machine is intended for installation on a "slab on grade" foundation. Installation is not recommended for elevated
floors unless special consideration is given to provide proper structural support.
2. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-5 for machine loads.
3. For planning purposes a minimum concrete foundation would be 4" thick minimum and 3' x 3' (or equivalent area).
Multiple machine installation would have equivalent foundation sizes.
4. Anchor bolts should be embedded in foundation 3". A template is provided with each washer or through repair parts for
this model for locating the anchor bolts.
5. The machine needs to be set level and the entire base fully supported with non-shrink grout, or shims.
6. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
7. Recommend 2" between machies. Recommend 24" service access behind machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR18 (ALL MODELS) 07/02 3-4
MFR18 (All Models)
1. Dry Weight Capacity 18 lbs. Machine dry weight capacity in pounds
1.2 kg
6. Maximum Static 383 lbs. Total static load, combined weight of machine, water and
Load 174.1 kg load
7. Area of Frame Base 3.65' Frame area, the floor space covered by the base of the base
111.2 cm of the machine
8. Static Load Pressure 105 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 324 lbs. Total dynamic load, G-Force times dry weight capacity times
712.8 kg 20% out-of-balance
10. Dynamic Load 89 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 9.17 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 662 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 300.9 kg weight capacity and dynamic load
13. Minimum Vertical 14 lbs. Minimum vertical load, dynamic load subtracted from empty
Load 6.4 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 324 lbs. Maximum lateral load, acts horizontally along a line of action
Load 147.2 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 1.9' Height of the basket centerline above floor, line of action of
Centerline 57.9 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 616 lbs. Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR18 (ALL MODELS) 07/02 3-5
Commercial PRODUCT DIMENSIONS
Front Load COLD
ELECTRICAL
POWER
WATER
Washers INLET
CONNECTION
HOT
WATER
44 7/8"
Models 114 cm
INLET
MFR 25 32 3/8"
82.2 cm 15 1/2"
(All Models) with handle 39.4 cm
3 9/16"
26" DRAIN 13"
30 3/4" 9 cm
OUTLET
78 cm 66 cm 33 cm
FRONT VIEW BACK VIEW
600 mm
Minimum Recommended
24"
Clearances*
PRODUCT SPECIFICATIONS
415 mm
16.33"
• Cylinder Volume: 3.27 cu. ft. (92.6 liter),
2" 2"
Diameter x Depth 21 x 16.5 inches (53.3 x 41.9 cm). 50 mm 50 mm
Positioning of Machines
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR25 (ALL MODELS) 07/02 3-6
WATER CONSUMPTION GALLONS - 25 LB. LOADS TOTAL
MFR25 PD PREWASH* WASH RINSE 1 RINSE 2 RINSE 3* TOTAL GALLONS
WHITE HOT 6.1 9.5 - - - 15.6 -
(PROGRAM 1) COLD 6.1 - 8.7 11.1 11.1 37 52.6
COLORS HOT 6.1 6.3 - - - 12.4 -
(PROGRAM 2) COLD 6.1 3.2 8.7 11.1 11.1 40.1 52.6
BRIGHT COLORS HOT - - - - - - -
(PROGRAM 3) COLD 12.1 9.5 8.7 11.1 11.1 52.6 52.6
PERM. PRESS HOT - 6.1 - - - 6.1 -
(PROGRAM 4) COLD - 6.1 8.7 11.1 11.1 37 43.1
DELICATES & KNITS HOT - 6.1 - - - 6.1 -
(PROGRAM 5) COLD - 6.1 8.7 11.1 11.1 37 43.1
WOOLENS HOT - - - - - - -
(PROGRAM 6) COLD - 12.2 8.7 11.1 11.1 43.1 43.1
* Optional on select models. PD cycle time 11.5 - 60.5 min. (plus fills)
PD models are generation 2 debit card ready
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR25 (ALL MODELS) 07/02 3-7
ELECTRICAL REQUIREMENTS
• 208/240 volts, single phase, 60 Hz, 20 amp circuit breaker, minimum wiring size awg. 12 of
copper wire only.
OR
• 208 / 240 volt, three phase, 60 Hz, 15 amp circuit breaker, minimum wiring size awg. 12 of
copper wire only.
• Individual branch circuits serving only the washers recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Single phase hookups require 3 wires. (2 wires plus ground)
• Line 1 • Line 2 • Earth Ground
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
WATER REQUIREMENTS
Water Connection Data
Model Water Valve Recommended Functioning Capacity at
Connection Water Pressure Limits 3 Bar or 40 psi
Inch psi bar psi bar gpm lit/m
MFR25 3/4" 30-85 2-6 30-120 2-8 11.6 44
• Maximum water temperature: 200°F (90°C).
• Access for manual shutoff of water recommended.
• Water inlet 3/4" (20 mm).
• Fill rate 11.6 gallons/minute (44 Liter / min.)
DRAIN FACILITY REQUIREMENTS
• Gravity Drain System
Washer should drain within 30 seconds of drain valve opening.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR25 (ALL MODELS) 07/02 3-8
FLOORING/MOUNTING REQUIREMENTS
Bolt should protrude 2 1/8" minimum out INSTALLATION OF MACHINE ANCHOR BOLTS
ANCHOR of cement pad plus grout thickness. DRAIN OPENING IN
GROUT FULL
BOLT SIZE WIDTH OF FRAME REAR OF BASE
3/8" - 1/2" FRAME GROUTING
BASE FRAME
inch mm NON SHRINK
COMPACTED
FILL DIRT
26"
66 cm
1 1/4"
3 cm
CABINET
OUTLINE
11 5/8"
29.5 cm
OVERHEAD VIEW
30 1/2" NOTE: 16007698 TYVEK Template
77.5 cm
available through repair parts sources.
14 3/8"
36.5 cm
3 5/8"
8.5 cm
FRONT
NOTES:
1. This machine is intended for installation on a "slab on grade" foundation. Installation is not recommended for elevated
floors unless special consideration is given to provide proper structural support.
2. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-10 for machine loads.
3. For planning purposes a minimum concrete foundation would be 4" thick minimum and 3'-6" x 3'-6" (or equivalent area).
Multiple machine installation would have equivalent foundation sizes.
4. Anchor bolts should be embedded in foundation 3". A template is provided with each washer or through repair parts for
this model for locating the anchor bolts.
5. The machine needs to be set level and the entire base fully supported with non-shrink grout, or shims.
6. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
7. Recommend 2" between machies. Recommend 24" service access behind machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR25 (ALL MODELS) 07/02 3-9
MFR25 (All Models)
1. Dry Weight Capacity 25 lbs. Machine dry weight capacity in pounds
11.4 kg
6. Maximum Static 464 lbs. Total static load, combined weight of machine, water and
Load 210.9 kg load
7. Area of Frame Base 4.72' Frame area, the floor space covered by the base of the base
143.9 cm of the machine
8. Static Load Pressure 98 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 450 lbs. Total dynamic load, G-Force times dry weight capacity times
204.5 kg 20% out-of-balance
10. Dynamic Load 95 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 9.17 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 848 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 385.4 kg weight capacity and dynamic load
13. Minimum Vertical -52 lbs. Minimum vertical load, dynamic load subtracted from empty
Load 23.6 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 450 lbs. Maximum lateral load, acts horizontally along a line of action
Load 204.5 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 2.02' Height of the basket centerline above floor, line of action of
Centerline 9.5 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 909 lbs. Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR25 (ALL MODELS) 07/02 3-10
Commercial PRODUCT DIMENSIONS
ELECTRICAL
Front Load COLD
POWER
CONNECTION
Washers WATER
INLET HOT
WATER
INLET
Models 51 3/4"
131.5 cm
MFR35 33 7/8"
with handle 18 1/4"
(All Models) 86.0 cm 46.4 cm
3 15/16"
31 3/4" 33 11/16" DRAIN
10.0 cm
80.5 cm OUTLET 16 7/8"
85.5 cm
FRONT VIEW BACK VIEW
600 mm
Minimum Recommended
24"
Clearances*
PRODUCT SPECIFICATIONS
415 mm
16.33"
• Cylinder Volume: 5.72 cu. ft. (162 liters),
2" 2"
Diameter x Depth 27 9/16 x 16 9/16 inches (70.0 x 42.0 cm). 50 mm 50 mm
Positioning of Machines
• PN models allow programming and operation in English,
French, German and Dutch. Spanish language TOP VIEW
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR35 (ALL MODELS) 07/02 3-11
WATER CONSUMPTION GALLONS - 35 LB. LOADS TOTAL
MFR35 MN MC & PD PREWASH* WASH RINSE 1 RINSE 2 RINSE 3* TOTAL GALLONS
WHITE HOT 9.8 15.1 - - - 24.8 -
(PROGRAM 1) COLD 9.8 - 15.1 19.3 19.3 63.4 88.2
COLORS HOT 9.8 10 - - - 19.8 -
(PROGRAM 2) COLD 9.8 5 15.1 19.3 19.3 68.4 88.2
BRIGHT COLORS HOT - - - - - - -
(PROGRAM 3) COLD 19.5 15.1 15.1 19.3 19.3 88.2 88.2
PERM. PRESS HOT - 9.8 - - - 9.8 -
(PROGRAM 4) COLD - 9.8 15.1 19.3 19.3 63.5 73.3
DELICATES & KNITS HOT - 9.8 - - - 9.8 -
(PROGRAM 5) COLD - 9.8 15.1 19.3 19.3 63.5 73.3
WOOLENS HOT - - - - - - -
(P6) PD model only COLD - 19.3 15.1 19.3 19.3 73 73.3
* Optional on select models. PD cycle time 11.5 - 60.5 min. (plus fills)
PD models are generation 2 debit card ready
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR35 (ALL MODELS) 07/02 3-12
WATER CONSUMPTION GALLONS - 35 LB. LOADS TOTAL
MFR35 PN PREWASH* WASH RINSE 1 RINSE 2 RINSE 3* TOTAL GALLONS
WHITE HOT 8.6 12.9 - - - 21.5 -
(PROGRAM 1) COLD 8.6 - 12.9 17.2 12.9 51.6 73.2
COLORS HOT 8.6 8.7 - - - 17.3 -
(PROGRAM 2) COLD 8.6 4.2 12.9 17.2 12.9 55.9 73.2
BRIGHT COLORS HOT - - - - - - -
(PROGRAM 3) COLD 17.2 12.9 12.9 17.2 12.9 73.2 73.2
PERM. PRESS HOT - 8.6 - - - 8.6 -
(PROGRAM 4) COLD - 8.6 12.9 12.9 12.9 47.3 56
DELICATES & KNITS HOT - 8.6 - - - 8.6 -
(PROGRAM 5) COLD - 8.6 12.9 12.9 12.9 47.3 56
WOOLENS HOT - - - - - - -
(PROGRAM 6) COLD - 17.2 12.9 12.9 12.9 56 56
ELECTRICAL REQUIREMENTS
• 240 volts, single phase, 60 Hz, 20 amp circuit breaker, minimum wiring size awg. 12 of copper
wire only.
OR
• 208 / 240 volt, three phase, 60 Hz, 15 amp circuit breaker, minimum wiring size awg. 12 of
copper wire only.
• Individual branch circuits serving only the washer recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Single phase hookups require 3 wires. (2 wires plus ground)
• Line 1 • Line 2 • Earth Ground
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
• A chemical injection terminal strip is located in the controls tray.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR35 (ALL MODELS) 07/02 3-13
WATER REQUIREMENTS
Water Connection Data
Model Water Valve Recommended Functioning Capacity at
Connection Water Pressure Limits 3 Bar or 40 psi
Inch psi bar psi bar gpm lit/m
MFR35 3/4" 30-85 2-6 30-120 2-8 13.2 50
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR35 (ALL MODELS) 07/02 3-13A
FLOORING/MOUNTING REQUIREMENTS
Bolt should protrude 2 1/8" minimum out INSTALLATION OF MACHINE ANCHOR BOLTS
ANCHOR of cement pad plus grout thickness. DRAIN OPENING IN
GROUT FULL
BOLT SIZE WIDTH OF FRAME REAR OF BASE
3/8" - 1/2" FRAME GROUTING
BASE FRAME
inch mm NON SHRINK
COMPACTED
FILL DIRT
33 11/16"
85.5 cm
2 3/8"
6 cm
CABINET
OUTLINE
11 5/8"
29.5 cm
OVERHEAD VIEW
14 7/16"
36 cm
3 9/16"
9.0 cm
FRONT
NOTES:
1. This machine is intended for installation on a "slab on grade" foundation. Installation is not recommended for elevated
floors unless special consideration is given to provide proper structural support.
2. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-15 for machine loads.
3. For planning purposes a minimum concrete foundation would be 6" thick minimum and 4' x 4' (or equivalent area).
Multiple machine installation would have equivalent foundation sizes.
4. Anchor bolts should be embedded in foundation 4". A template is provided with each washer or through repair parts for
this model for locating the anchor bolts.
5. The machine needs to be set level and the entire base fully supported with non-shrink grout, or shims.
6. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
7. Recommend 2" between machies. Recommend 24" service access behind machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR35 (ALL MODELS) 07/02 3-14
MFR35 (All Models)
1. Dry Weight Capacity 35 lbs. Machine dry weight capacity in pounds
15.9 kg
6. Maximum Static 750 lbs. Total static load, combined weight of machine, water and
Load 340.9 kg load
7. Area of Frame Base 6.27' Frame area, the floor space covered by the base of the base
191.1 cm of the machine
8. Static Load Pressure 120 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 560 lbs. Total dynamic load, G-Force times dry weight capacity times
254.5 kg 20% out-of-balance
10. Dynamic Load 89 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 7.5 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 1208 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 549.1 kg weight capacity and dynamic load
13. Minimum Vertical 88 lbs. Minimum vertical load, dynamic load subtracted from empty
Load 40 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 560 lbs. Maximum lateral load, acts horizontally along a line of action
Load 254.5 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 2.92' Height of the basket centerline above floor, line of action of
Centerline 89 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 1635 lbs. Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR35 (ALL MODELS) 07/02 3-15
Commercial PRODUCT DIMENSIONS
ELECTRICAL
Front Load COLD POWER
CONNECTION
Washers WATER
INLET HOT
WATER
51 3/4" INLET
Models 131.5 cm
42 15/16"
MFR50 109 cm 18 1/4"
46.4 cm
(All Models) with handle
3 15/16"
33 11/16" DRAIN
40 3/4" 10 cm
OUTLET 16 7/8"
103.5 cm 85.5 cm
FRONT VIEW BACK VIEW
600 mm
Minimum Recommended
24"
Clearances*
PRODUCT SPECIFICATIONS
415 mm
16.33"
• Cylinder Volume: 7.68 cu. ft. (217 liter),
Diameter x Depth 27 9/16 x 22 3/4 inches (70 x 57.8 cm). 2"
50 mm
2"
50 mm
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR50 (ALL MODELS) 07/02 3-16
WATER CONSUMPTION GALLONS - 50 LB. LOADS TOTAL
MFR50 MN MC & PD PREWASH* WASH RINSE 1 RINSE 2 RINSE 3* TOTAL GALLONS
WHITE HOT 12.9 20.3 - - - 33.3 -
(PROGRAM 1) COLD 12.9 - 20.3 26.1 26.1 85.6 118.9
COLORS HOT 12.9 10.8 - - - 23.8 -
(PROGRAM 2) COLD 12.9 9.2 20.3 26.1 26.1 94.8 118.9
BRIGHT COLORS HOT - - - - - - -
(PROGRAM 3) COLD 25.9 20.3 20.3 26.1 26.1 188.9 118.9
PERM. PRESS HOT - 12.9 - - - 12.9 -
(PROGRAM 4) COLD - 12.9 20.3 26.1 26.1 85.4 98.3
DELICATES & KNITS HOT - 12.9 - - - 12.9 -
(PROGRAM 5) COLD - 12.9 20.3 26.1 26.1 85.4 98.3
WOOLENS HOT - - - - - - -
(P6) PD model only COLD - 25.9 20.3 26.1 26.1 98.3 98.3
* Optional on select models. PD cycle time 11.5 - 60.5 min. (plus fills) PD models are generation 2 debit card ready
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR50 (ALL MODELS) 07/02 3-17
WATER CONSUMPTION GALLONS - 50 LB. LOADS TOTAL
MFR50 PN PREWASH* WASH RINSE 1 RINSE 2 RINSE 3* TOTAL GALLONS
WHITE HOT 11.6 17.4 - - - 29.1 -
(PROGRAM 1) COLD 11.6 - 17.4 23.2 23.2 75.4 104.4
COLORS HOT 11.6 11.6 - - - 23.2 -
(PROGRAM 2) COLD 11.6 5.8 17.4 23.2 23.2 81.2 104.4
BRIGHT COLORS HOT - - - - - - -
(PROGRAM 3) COLD 23.2 17.4 17.4 23.2 23.2 104.4 104.4
PERM. PRESS HOT - 11.6 - - - 11.6 -
(PROGRAM 4) COLD - 11.6 17.4 23.2 23.2 75.4 87
DELICATES & KNITS HOT - 11.6 - - - 11.6 -
(PROGRAM 5) COLD - 11.6 17.4 23.2 23.2 75.4 87
WOOLENS HOT - - - - - - -
(P6) PD model only COLD - 23.2 17.4 23.2 23.2 87 87
ELECTRICAL REQUIREMENTS
• 240 volts, single phase, 60 Hz, 20 amp circuit breaker, minimum wiring size awg. 10 of copper
wire only.
OR
• 208 / 240 volt, three phase, 60 Hz, 15 amp circuit breaker, minimum wiring size awg. 12 of
copper wire only.
• Individual branch circuits serving only the washer recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Single phase hookups require 3 wires. (2 wires plus ground)
• Line 1 • Line 2 • Earth Ground
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR50 (ALL MODELS) 07/02 3-18
WATER REQUIREMENTS
Water Connection Data
Model Water Valve Recommended Functioning Capacity at
Connection Water Pressure Limits 3 Bar or 40 psi
Inch psi bar psi bar gpm lit/m
MFR50 3/4" 30-85 2-6 30-120 2-8 13.2 50
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR50 (ALL MODELS) 07/02 3-19
FLOORING/MOUNTING REQUIREMENTS
Bolt should protrude 2 1/8" minimum out INSTALLATION OF MACHINE ANCHOR BOLTS
ANCHOR of cement pad plus grout thickness. DRAIN OPENING IN
GROUT FULL
BOLT SIZE WIDTH OF FRAME REAR OF BASE
3/8" - 1/2" FRAME GROUTING
BASE FRAME
inch mm NON SHRINK
COMPACTED
FILL DIRT
33 11/16"
85.5 cm
2 3/8"
6 cm
CABINET
OUTLINE
15 3/8"
38.5 cm
OVERHEAD VIEW
40 3/4"
103.5 cm NOTE: 16007698 TYVEK Template
available through repair parts sources.
19 3/16"
50 cm
3 9/16"
9.0 cm
NOTES:
1. This machine is intended for installation on a "slab on grade" foundation. Installation is not recommended for elevated
floors unless special consideration is given to provide proper structural support.
2. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-21 for machine loads.
3. For planning purposes a minimum concrete foundation would be 6" thick minimum and 4' x 4' (or equivalent area).
Multiple machine installation would have equivalent foundation sizes.
4. Anchor bolts should be embedded in foundation 4". A template is provided with each washer or through repair parts for
this model for locating the anchor bolts.
5. The machine needs to be set level and the entire base fully supported with non-shrink grout, or shims.
6. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
7. Recommend 2" between machies. Recommend 24" service access behind machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR50 (ALL MODELS) 07/02 3-20
MFR50 (All Models)
1. Dry Weight Capacity 50 lbs. Machine dry weight capacity in pounds
22.7 kg
6. Maximum Static 971' Total static load, combined weight of machine, water and
Load 251.8 cm load
7. Area of Frame Base 8.26' Frame area, the floor space covered by the base of the base
251.8 cm of the machine
8. Static Load Pressure 118 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 800 lbs. Total dynamic load, G-Force times dry weight capacity times
363.6 kg 20% out-of-balance
10. Dynamic Load 97 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 7.50 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 1633 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 742.3 kg weight capacity and dynamic load
13. Minimum Vertical 33 lbs. Minimum vertical load, dynamic load subtracted from empty
Load 15 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 800 lbs. Maximum lateral load, acts horizontally along a line of action
Load 363.6 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 2.95' Height of the basket centerline above floor, line of action of
Centerline 89.9 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 2360 Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR50 (ALL MODELS) 07/02 3-21
Commercial PRODUCT DIMENSIONS
ELECTRICAL
Front Load COLD POWER
CONNECTION
Washers WATER
INLET HOT
WATER
57" INLET
Models 144.8 cm
42 15/16"
MFR80 109 cm 17 1/2"
15 3/4"
40 cm
44.5 cm
(All Models) with handle
2 DRAIN 3 9/16"
40 3/4" 42 1/2" OUTLETS 15 3/4" 9 cm
103.5 cm 110.5 cm 40 cm
FRONT VIEW BACK VIEW
609.6 mm
Minimum Recommended
24"
Clearances*
PRODUCT SPECIFICATIONS
• Cylinder Volume: 11.79 cu. ft. (333.8 liter), 2" 4"
Diameter x Depth 36 x 20 inches (91.4 x 50.8 cm). 51 mm 100 mm
Positioning of Machines
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR80 (ALL MODELS) 07/02 3-22
WATER CONSUMPTION GALLONS - 80 LB. LOADS TOTAL
MFR80 PD PREWASH* WASH RINSE 1 RINSE 2 RINSE 3* TOTAL GALLONS
WHITE HOT 19.8 30.9 - - - 50.7 -
(PROGRAM 1) COLD 19.8 - 30.9 39.6 39.6 129.9 180.7
COLORS HOT 19.8 16.1 - - - 35.9 -
(PROGRAM 2) COLD 19.8 14.5 30.9 39.6 39.6 144.5 180.7
BRIGHT COLORS HOT - - - - - - -
(PROGRAM 3) COLD 39.6 30.9 30.9 39.6 39.6 180.7 180.7
PERM. PRESS HOT - 19.8 - - - 19.8 -
(PROGRAM 4) COLD - 19.8 30.9 39.6 39.6 129.9 149.7
DELICATES & KNITS HOT - 19.8 - - - 19.8 -
(PROGRAM 5) COLD - 19.8 30.9 39.6 39.6 129.9 149.7
WOOLENS HOT - - - - - - -
(P6) PD model only COLD - 39.6 30.9 39.6 39.6 149.7 149.7
* Optional on select models. PD cycle time 11.5 - 60.5 min. (plus fills)
PD models are generation 2 debit card ready
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR80 (ALL MODELS) 07/02 3-23
ELECTRICAL REQUIREMENTS
• 208 / 240 volts, three phase, 60 Hz, 30 amp circuit breaker, minimum wiring size awg. 10 of
copper wire only.
• Individual branch circuits serving only the washers recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
WATER REQUIREMENTS
Water Connection Data
Model Water Valve Recommended Functioning Capacity at
Connection Water Pressure Limits 3 Bar or 40 psi
Inch psi bar psi bar gpm lit/m
MFR80 3/4" 30-85 2-6 30-120 2-8 13.2 50
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR80 (ALL MODELS) 07/02 3-24
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR80 (ALL MODELS) 07/02 3-25
FLOORING/MOUNTING REQUIREMENTS
Bolt should protrude 2 1/8" minimum out INSTALLATION OF MACHINE ANCHOR BOLTS
ANCHOR of cement pad plus grout thickness. GROUT FULL DRAIN OPENING IN
BOLT SIZE WIDTH OF FRAME REAR OF BASE
3/8" - 1/2" FRAME GROUTING
BASE FRAME
inch mm NON SHRINK
3/4" 19 3" PROJECTION MAXIMUM
9"
CONCRETE
FLOOR
COMPACTED
FILL DIRT
42 1/2"
108.0 cm
2 1/4"
5.4 cm
CABINET
OUTLINE
10 5/8"
27.0 cm
11 1/4"
29.4 cm
5"
12.8 cm
FRONT
NOTES:
1. This machine is intended for installation on a "slab on grade" foundation. Installation is not recommended for elevated
floors unless special consideration is given to provide proper structural support.
2. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-26 for machine loads.
3. For planning purposes a minimum concrete foundation would be 9" thick minimum and 5' x 5' (or equivalent area).
Multiple machine installation would have equivalent foundation sizes.
4. Anchor bolts should be embedded in foundation 7". A template is provided with each washer or through repair parts for
this model for locating the anchor bolts.
5. The machine needs to be set level and the entire base fully supported with non-shrink grout, or shims.
6. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
7. Recommend 4" between machies. Recommend 24" service access behind machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR80 (ALL MODELS) 07/02 3-26
MFR80PD
1. Dry Weight Capacity 80 lbs. Machine dry weight capacity in pounds
36.4 kg
3. Extract G-Force 130 Maximum G-Force, or the force applied to the load at
periphery of cylinder during extraction
1539 lbs.
4. Empty Weight Weight of machine - empty
699.5 kg
5. Weight of Water 106 lbs. Weight of water in the machine at high level when loaded
48.2 kg
6. Maximum Static 1725 lbs. Total static load, combined weight of machine, water and
Load 784.1 kg load
7. Area of Frame Base 11.35' Frame area, the floor space covered by the base of the base
345.9 cm of the machine
8. Static Load Pressure 152 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 2080 lbs. Total dynamic load, G-Force times dry weight capacity times
945.4 kg 20% out-of-balance
10. Dynamic Load 183 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 8.50 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 3699 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 1681.4 kg weight capacity and dynamic load
13. Minimum Vertical -461 lbs. Minimum vertical load, dynamic load subtracted from empty
Load -209.5 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 2080 lbs. Maximum lateral load, acts horizontally along a line of action
Load 96 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 3.15' Height of the basket centerline above floor, line of action of
Centerline 96 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 6552 Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
COMMERCIAL FRONT LOAD WASHERS - MODELS MFR80 (ALL MODELS) 07/02 3-27
Commercial PRODUCT DIMENSIONS
Front Load WATER
Washers CONNECTIONS
AIR VENT
ELECTRICAL
POWER
CONNECTION
Models
47 1/4"
MFS35 120 cm
39 9/16"
(All Models) 100.5 cm
with 16 3/8"
handle 41.5 cm
19 11/16" 2 3 /16"
50 cm 5.5 cm
DRAIN
Soft Mount 37 3/4"
32 11/16"
OUTLET
96 cm
(Free Standing) 83 cm
FRONT VIEW
BACK VIEW
PRODUCT SPECIFICATIONS
• Cylinder Volume: 5.87 cu. ft. (166 liter),
Diameter x Depth 25 5/8 x 19 3/4 inches (65.1 x 50.2 cm).
• PN models allow programming and operation in English, French, German, Dutch, and
Spanish.
• Wash speed: 45 rpm.
• Extract: 500 rpm low.
1,000 rpm high.
• Distribution Speed: 100 rpm.
• G-Force: 91 low.
363 high.
• Motor: Two, two-speed motors
Wash: 1/2 Hp (.37 Kw), Extract: 2 Hp (1.5 Kw).
• Uses .5 Kwh per average load.
• Water inlet : 3/4", (19 mm) hose thread. (adapter hoses supplied)
• Operating Pressure: 30-85 psi (2-6 bar).
• Drain: 2.6" I.D. (66 mm I.D.). 3" O.D. (76 mm O.D.)
• Net Weight: 890 lbs. (404 Kg).
• Crated Weight: 915 lbs. (415 Kg).
• Door Opening: 12" (305 mm).
• Maximum Amperage Draw
Three Phase - 7.8 amps, (except for motor starting surges)
• Pressure Fill System.
• Recommended Breaker Size
Three Phase - 15 amps, (except for motor starting surges)
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS35 (ALL MODELS) 07/02 3-28
WHITES (P1) COLORS (P2) BR. CLRS (P3) PRM. PRESS (P4) DELI. & KNITS (P5)
Cold water 67.9 gal 73.4 gal 76.3 gal 54.7 gal 65..3 gal
257 liters 278 liters 289 liters 207 liters 247 liters
Warm water 26.7 gal 21.1 gal 18.29 gal 9.8 gal -
101 liters 80 liters 69 liters 37 liters -
Total water 94.6 gal 94.6 gal 94.6 gal 64.5 gal 65.3 gal
consumption 358 liters 358 liters 358 liters 244 liters 247 liters
Average water consumption with no load.
* Water use can vary due to custom programming.
(NOTE: The water use goes up at a rate of .25 gallons per pound of clothes. This is a "rule of thumb".)
Assuming terry cloth material = .2 gallons per pound with cotton.
Additional Programmed Cycles Not Shown.
ELECTRICAL REQUIREMENTS
• 208 / 240 volt, three phase, 60 Hz, 15 amp circuit breaker, minimum wiring size awg. 12 of
copper wire only.
• Individual branch circuit serving only the washer recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
• A chemical injection terminal strip is located in the controls tray.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS35 (ALL MODELS) 07/02 3-29
WATER REQUIREMENTS
Water Connection Data
Model Water Valve Recommended Functioning Capacity at
Connection Water Pressure Limits 3 Bar or 40 psi
Inch psi bar psi bar gpm lit/m
MFS35 3/4" 30-85 2-6 30-120 2-8 13.2 50
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS35 (ALL MODELS) 07/02 3-30
FLOORING/MOUNTING REQUIREMENTS
NOTE: This is a soft mount model. INSTALLATION OF MACHINE ANCHOR BOLTS
ANCHOR Cement floor thickness and bolt size
BOLT SIZE information is provided ONLY for
inch mm installations where the model is to be BASE FRAME
bolted to the floor or an elevated base.
3/8" 10 This is not required. 3" PROJECTION MAXIMUM
COMPACTED
FILL DIRT
32 11/16"
83 cm
2 9/16"
6.5 cm
CABINET
OUTLINE
OVERHEAD VIEW
37 13/16" 32 1/16"
96 cm 81.5 cm
3 3/16"
8 cm
28 1/16"
71.5 cm
2 1/4" FRONT 2 1/4"
5.7 cm 5.7 cm
NOTES:
1. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-31 for machine loads.
2. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
3. Recommend 2" between machies. Recommend 24" service access behind machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS35 (ALL MODELS) 07/02 3-31
MFS35PN
1. Dry Weight Capacity 35 lbs. Machine dry weight capacity in pounds
15.9 kg
3. Extract G-Force 363 Maximum G-Force, or the force applied to the load at
periphery of cylinder during extraction
860 lbs.
4. Empty Weight Weight of machine - empty
390.9 kg
5. Weight of Water 100 lbs. Weight of water in the machine at high level when loaded
45.4 kg
6. Maximum Static 995 lbs. Total static load, combined weight of machine, water and
Load 452.3 kg load
7. Area of Frame Base 8.58' Frame area, the floor space covered by the base of the base
261.5 cm of the machine
8. Static Load Pressure 116 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 2541 lbs. Total dynamic load, G-Force times dry weight capacity times
1155 kg 20% out-of-balance
10. Dynamic Load 296 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 16.67 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 3436 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 1561.8 kg weight capacity and dynamic load
13. Minimum Vertical -1646 lbs. Minimum vertical load, dynamic load subtracted from empty
Load -748.2 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 2541 lbs. Maximum lateral load, acts horizontally along a line of action
Load 1155 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 2.11' Height of the basket centerline above floor, line of action of
Centerline 64.3 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 5362 Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
Note: This is a soft mount model.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS35 (ALL MODELS) 07/02 3-32
Commercial PRODUCT DIMENSIONS
Front Load ELECTRICAL
POWER
WATER
CONNECTIONS
Washers CONNECTION
64 3/16"
Models 164 cm
DRAIN
MFS50 24 1/4"
61 cm
OUTLET
7 7/8"
(All Models) 38 7/8"
37 1/2"
98.5 cm 11"
20 cm
PRODUCT SPECIFICATIONS
• Cylinder Volume: 7.8 cu. ft. (220.9 liters),
Diameter x Depth 29 1/2 x 19 11/16 inches (74.9 x 50 cm).
• PN models allow programming and operation in English, French, German, Dutch, and
Spanish.
• Wash speed: 42 rpm.
• Extract: 435 rpm low.
860 rpm high.
• Distribution Speed: 68 rpm.
• G-Force: 72 low.
310 high.
• Motor: Two, two-speed motors
Wash: .7/.9 Hp (.52/.67 Kw), Extract: 2.4/3 Hp (1.8/2.2 Kw).
• Uses .6 Kwh per average load.
• Water inlet : 3/4", (19 mm) male hose thread (adapter hoses supplied).
• Operating Pressure: 30-120 psi (2-8 bar).
• Drain: 2.55" I.D. (65 mm I.D.). 3" O.D. (75 mm O.D.)
• Net Weight: 1493 lbs. (677 Kg).
• Crated Weight: 1581 lbs. (717 Kg).
• Door Opening: 16 1/8" (410 mm).
• Maximum Amperage Draw
Three Phase - 14 amps, (except for motor starting surges)
• Pressure Fill System.
• Recommended Breaker Size
Three Phase - 20 amps
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS50 (ALL MODELS) 07/02 3-33
WATER CONSUMPTION GALLONS*
TOTAL
MFS50PND PREWASH WASH RINSE 1 RINSE 2 RINSE 3 TOTAL GALLONS
WHITE HOT 11.6 17.4 - - - 29.0
(PROGRAM 1) COLD 11.6 - 18.0 23.2 17.4 70.2 99.2
COLORS HOT 11.6 11.6 - - - 23.2
(PROGRAM 2) COLD 11.6 5.8 18.0 23.2 17.4 76.0 99.2
BRIGHT COLORS HOT 11.6 8.7 - - - 20.3
(PROGRAM 3) COLD 11.6 8.7 18.0 23.2 17.4 78.9 99.2
PERM. PRES HOT - 11.6 - - - 11.6
(PROGRAM 4) COLD - 11.6 18.0 18.0 12.2 59.8 71.4
DELICATES HOT - - - - - - -
& KNITS (P5) COLD - 23.3 18.0 18.0 18.0 77.3 77.3
ELECTRICAL REQUIREMENTS
• 208 / 240 volt, three phase, 60 Hz, 20 amp circuit breaker, minimum wiring size awg. 12 of
copper wire only.
• Individual branch circuit serving only the washer recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
• A chemical injection terminal strip is located in the controls tray.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS50 (ALL MODELS) 07/02 3-34
WATER REQUIREMENTS
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS50 (ALL MODELS) 07/02 3-35
FLOORING/MOUNTING REQUIREMENTS
COMPACTED
FILL DIRT
38 7/8"
98.5 cm
4"
10 cm
CABINET
OUTLINE
37 1/2"
OVERHEAD VIEW
94.9 cm
30 1/2"
77.4 cm
3"
7.5 cm
34 7/8"
88.6 cm
NOTES:
1. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-36 for machine loads.
2. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
3. Recommend 2" between machies. Recommend 24" service access behind machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS50 (ALL MODELS) 07/02 3-36
MFS50PN
1. Dry Weight Capacity 50 lbs. Machine dry weight capacity in pounds
22.7 kg
3. Extract G-Force 310 Maximum G-Force, or the force applied to the load at
periphery of cylinder during extraction
1459 lbs.
4. Empty Weight Weight of machine - empty
663.2 kg
5. Weight of Water 134 lbs. Weight of water in the machine at high level when loaded
60.9 kg
6. Maximum Static 1643 lbs. Total static load, combined weight of machine, water and
Load 746.8 kg load
7. Area of Frame Base 8.41' Frame area, the floor space covered by the base of the base
256.3 cm of the machine
8. Static Load Pressure 195 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 3100 lbs. Total dynamic load, G-Force times dry weight capacity times
1409.1 kg 20% out-of-balance
10. Dynamic Load 369 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 14.33 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 4609 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 2095 kg weight capacity and dynamic load
13. Minimum Vertical -1591 lbs. Minimum vertical load, dynamic load subtracted from empty
Load -723.2 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 3100 lbs. Maximum lateral load, acts horizontally along a line of action
Load 1409.1 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 2.81' Height of the basket centerline above floor, line of action of
Centerline 85.6 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 8711 Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS50 (ALL MODELS) 07/02 3-37
Commercial PRODUCT DIMENSIONS
Front Load
ELECTRICAL WATER
Washers POWER
CONNECTION
CONNECTIONS
Models 74 7/8"
190.3 cm
MFS80 DRAIN
OUTLETS
(Free Standing)
*a minimum of 31" is recommended above
washer to raise hinged top for service
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS80 (ALL MODELS) 07/02 3-38
WATER CONSUMPTION GALLONS*
TOTAL
MFS80PND PREWASH WASH RINSE 1 RINSE 2 RINSE 3 TOTAL GALLONS
WHITE HOT 17.6 26.4 - - - 44.0
(PROGRAM 1) COLD 17.6 - 27.2 35.1 26.4 106.3 150.3
COLORS HOT 17.6 17.4 - - - 35.0
(PROGRAM 2) COLD 17.6 9.0 27.2 35.1 26.4 115.3 150.3
BRIGHT COLORS HOT 17.6 13.2 - - - 30.8
(PROGRAM 3) COLD 17.6 13.2 27.2 35.1 26.4 119.5 150.3
PERM. PRESS HOT - 17.7 - - - 17.7
(PROGRAM 4) COLD - 17.7 27.2 27.2 18.5 90.6 108.3
DELICATES HOT - - - - - - -
& KNITS (P5) COLD - 35.1 27.2 27.2 27.2 116.7 116.7
ELECTRICAL REQUIREMENTS
• 208 / 240 volt, three phase, 60 Hz, 20 amp circuit breaker, minimum wiring size awg. 12 of
copper wire only.
• Individual branch circuit serving only the washer recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
• A chemical injection terminal strip is located in the controls tray.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS80 (ALL MODELS) 07/02 3-39
WATER REQUIREMENTS
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS80 (ALL MODELS) 07/02 3-40
FLOORING/MOUNTING REQUIREMENTS
COMPACTED
FILL DIRT
46 7/8"
119 cm
7 7/8"
CABINET 20 cm
OUTLINE
OVERHEAD VIEW
49 1/8" 38 1/4"
124.7 cm 97.0 cm
3"
7.7 cm
36 5/8"
93.0 cm
NOTES:
1. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-41 for machine loads.
2. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
3. Recommend 4" between machies. Recommend 24" service access behind machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS80 (ALL MODELS) 07/02 3-41
MFS80PN
1. Dry Weight Capacity 80 lbs. Machine dry weight capacity in pounds
36.4 kg
3. Extract G-Force 365 Maximum G-Force, or the force applied to the load at
periphery of cylinder during extraction
2974 lbs.
4. Empty Weight Weight of machine - empty
1351.8 kg
5. Weight of Water 224 lbs. Weight of water in the machine at high level when loaded
101.8 kg
6. Maximum Static 3273 lbs. Total static load, combined weight of machine, water and
Load 1487.7 kg load
7. Area of Frame Base 14.17' Frame area, the floor space covered by the base of the base
431.9 cm of the machine
8. Static Load Pressure 231 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 5475 lbs. Total dynamic load, G-Force times dry weight capacity times
2488.6 kg 20% out-of-balance
10. Dynamic Load 386 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 14.08 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 8524 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 3874.5 kg weight capacity and dynamic load
13. Minimum Vertical -2426 lbs. Minimum vertical load, dynamic load subtracted from empty
Load -1102.7 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 5475 lbs. Maximum lateral load, acts horizontally along a line of action
Load 2488.6 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 3.51' Height of the basket centerline above floor, line of action of
Centerline 107 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 19217 Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS80 (ALL MODELS) 07/02 3-42
Commercial PRODUCT DIMENSIONS
Front Load
ELECTRICAL WATER
Washers POWER
CONNECTION
CONNECTIONS
Models 74 7/8"
190.3 cm
MFS100 DRAIN
OUTLETS
PRODUCT SPECIFICATIONS
• Cylinder Volume: 14.2 cu. ft. (402 liter),
Diameter x Depth 36 x 24 inches (91.4 x 61 cm).
• PN models allow programming and operation in English, French, German, Dutch, and
Spanish.
• Wash speed: 40 rpm.
• Extract: 415 rpm low.
830 rpm high.
• Distribution Speed: 70 rpm.
• G-Force: 90 low.
350 high.
• Motor: Two, two-speed motors
Wash: 1.3/1.5 Hp (1.0/1.1 Kw), Extract: 6/7.8 Hp (4.5/5.8 Kw).
• Uses 22.5 Kwh per average load.
• Water inlet : 1", (2.5 mm) male hose thread.
• Operating Pressure: 30-120 psi (3-8 bar).
• Drain: two outlet 2.55" I.D. (65 mm I.D.). 3" O.D. (75 mm O.D.).
• Net Weight: 3228 lbs. (1466 Kg).
• Crated Weight: 3669 lbs. (1666 Kg).
• Door Opening: 21 3/16 (53.8 cm).
• Maximum Amperage Draw
Three Phase - 25 amps (except for motor starting surges)
• Pressure Fill System.
• Recommended Breaker Size
Three Phase - 30 amps.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS100 (ALL MODELS) 07/02 3-43
WATER CONSUMPTION GALLONS*
TOTAL
MFS100PD PREWASH WASH RINSE 1 RINSE 2 RINSE 3 TOTAL GALLONS
WHITE HOT 21.1 31.7 - - - 52.8
(PROGRAM 1) COLD 21.1 - 32.8 42.3 31.7 127.9 180.7
COLORS HOT 21.1 21.1 - - - 42.2
(PROGRAM 2) COLD 21.1 10.6 32.8 42.3 31.7 138.5 180.7
BRIGHT COLORS HOT 21.1 15.9 - - - 37.0
(PROGRAM 3) COLD 21.1 15.9 32.8 42.3 31.7 143.8 180.8
PERM. PRESS HOT - 21.1 - - - 21.1
(PROGRAM 4) COLD - 21.1 32.8 32.8 22.2 108.9 130.0
DELICATES HOT - - - - - - -
& KNITS (P5) COLD - 42.3 32.8 32.8 32.8 140.7 140.7
ELECTRICAL REQUIREMENTS
• 208 / 240 volt, three phase, 60 Hz, 30 amp circuit breaker, minimum wiring size awg. 10 of
copper wire only.
• Individual branch circuit serving only the washer recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
• A chemical injection terminal strip is located in the controls tray.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS100 (ALL MODELS) 07/02 3-44
WATER REQUIREMENTS
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS100 (ALL MODELS) 07/02 3-45
FLOORING/MOUNTING REQUIREMENTS
COMPACTED
FILL DIRT
46 7/8"
119 cm
7 7/8"
CABINET 20 cm
OUTLINE
OVERHEAD VIEW
53" 42 1/8"
134.7 cm 107 cm
3"
7.7 cm
36 5/8"
93.0 cm
NOTES:
1. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-46 for machine loads.
2. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
3. Recommend 4" between machies. Recommend 24" service access behind machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS100 (ALL MODELS) 07/02 3-46
MFS100
1. Dry Weight Capacity 100 lbs. Machine dry weight capacity in pounds
45.4 kg
3. Extract G-Force 350 Maximum G-Force, or the force applied to the load at
periphery of cylinder during extraction
3402 lbs.
4. Empty Weight Weight of machine - empty
1546.4 kg
5. Weight of Water 251 lbs. Weight of water in the machine at high level when loaded
114.1 kg
6. Maximum Static 3743 lbs. Total static load, combined weight of machine, water and
Load 1701.4 kg load
7. Area of Frame Base 15.39' Frame area, the floor space covered by the base of the base
469.1 cm of the machine
8. Static Load Pressure 243 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 6300 lbs. Total dynamic load, G-Force times dry weight capacity times
2863.6 kg 20% out-of-balance
10. Dynamic Load 409 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 13.83 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 9792 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 4450.9 kg weight capacity and dynamic load
13. Minimum Vertical -2808 lbs. Minimum vertical load, dynamic load subtracted from empty
Load -1276.4 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 6300 lbs. Maximum lateral load, acts horizontally along a line of action
Load 2863.6 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 3.51' Height of the basket centerline above floor, line of action of
Centerline 107 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 22113 Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
COMMERCIAL FRONT LOAD WASHERS - MODELS MFS100 (ALL MODELS) 07/02 3-47
Commercial PRODUCT DIMENSIONS
Front Load WATER
CONNECTIONS
Washers ELECTRICAL
POWER
CONNECTION
Models 74 7/8"
190.1 cm
MFS125 DRAIN
28 3/4" OUTLETS
73 cm
8 1/16"
20.5 cm
Soft Mount 46 7/8"
119.1 cm
60 1/8"
152.7 cm 8 3/8"
21.3 cm
61 1/8"
(Free Standing) FRONT VIEW
155.2 cm
SIDE VIEW
19 1/4" 49 cm
BACK VIEW
PRODUCT SPECIFICATIONS
• Cylinder Volume: 18.3 cu. ft. (518 liter),
Diameter x Depth 36 x 31 inches (91.4 x 78.7 cm).
• PN models allow programming and operation in English, French, German, Dutch, and
Spanish.
• Wash speed: 40 rpm.
• Extract: 415 rpm low.
830 rpm high.
• Distribution Speed: 70 rpm.
• G-Force: 90 low.
350 high.
• Motor: Two, two-speed motors
Wash: 1.6/1.9 Hp (1.2/1.4 Kw), Extract: 6.7/8.7 Hp (5/6.5 Kw).
• Uses 1.6 Kwh per average load.
• Water inlet : 1", (25.4 mm) hose thread with 39" braided stainless inlet hoses provided.
• Operating Pressure: 30-85 psi (2-6 bar).
• Drain: two outlets 2.55" I.D. (65 mm I.D.). 3" O.D. (75 mm O.D.)
• Net Weight: 3520 lbs. (1597 Kg).
• Crated Weight: 4105 lbs. (1826 Kg).
• Door Opening: 21 3/16" (53.8 cm).
• Maximum Amperage Draw
Three Phase - 30 amps (except for motor starting surges)
• Pressure Fill System.
• Recommended Breaker Size
Three Phase - 40 amps.
ELECTRICAL REQUIREMENTS
• 208 / 240 volt, three phase, 60 Hz, 40 amp circuit breaker, minimum wiring size awg. 8 of
copper wire only.
• Individual branch circuit serving only the washer recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
• A chemical injection terminal strip is located in the controls tray.
COMPACTED
FILL DIRT
46 7/8"
119 cm
7 7/8"
20 cm
OVERHEAD VIEW
60 1/8" 49 1/4"
152.7 cm 125.0 cm
3"
7.7 cm
36 5/8"
93.0 cm
NOTES:
1. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-51 for machine loads.
2. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
3. Recommend 4" between machies. Recommend 24" service access behind machine.
3. Extract G-Force 350 Maximum G-Force, or the force applied to the load at
periphery of cylinder during extraction
3547 lbs.
4. Empty Weight Weight of machine - empty
1612.3 kg
5. Weight of Water 328 lbs. Weight of water in the machine at high level when loaded
149.1 kg
6. Maximum Static 4000 lbs. Total static load, combined weight of machine, water and
Load 1818.2 kg load
7. Area of Frame Base 17.64' Frame area, the floor space covered by the base of the base
537.7 cm of the machine
8. Static Load Pressure 227 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 8750 lbs. Total dynamic load, G-Force times dry weight capacity times
3977.3 kg 20% out-of-balance
10. Dynamic Load 496 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 13.83 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 12422 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 5646.4 kg weight capacity and dynamic load
13. Minimum Vertical -5078 lbs. Minimum vertical load, dynamic load subtracted from empty
Load -2308.2 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 8750 lbs. Maximum lateral load, acts horizontally along a line of action
Load 3977.3 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 3.51' Height of the basket centerline above floor, line of action of
Centerline 107 kg lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 30713 Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
Washers CONNECTION
WATER 10 3/4"
CONNECTIONS 27.3 cm
Models
67 3/4"
MFX50 167 cm
3 7/8
BACK VIEW
OPL
*a minimum of 18" is recommended above
washer to raise hinged top for service
WHITE GALLONS*
MFX50 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL GALLONS
HOT 12.6 16.6 - - - - 27
COLD 12.6 - 31 37.5 38.4 33.2 152.7
179.7
WHITE LITERS*
MFX50 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL LITERS
HOT 47.7 62.9 - - - - 102.3
COLD 47.7 - 117.5 142.1 145.5 125.8 578.7
681.1
*Water use can vary due to custom programming.
COLORS GALLONS*
MFX50 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL GALLONS
HOT - 7.2 - - - - 7.2
COLD 25.2 7.2 31 37.5 38.4 33.2 172.5
179.7
COLORS LITERS*
MFX50 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL LITERS
HOT - 27.3 - - - - 27.3
COLD 95.5 27.3 117.5 142.1 145.5 125.8 653.8
681.1
*Water use can vary due to custom programming.
ELECTRICAL REQUIREMENTS
• 208 / 240 volt, three phase, 60 Hz, 15 amp circuit breaker, minimum wiring size awg. 12 of
copper wire only.
• Individual branch circuit serving only the washer recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
ANCHOR Bolt should protrude 2 1/8” out of INSTALLATION OF MACHINE ANCHOR BOLTS
GROUT FULL DRAIN OPENING IN
BOLT SIZE cement pad plus grout thickness. WIDTH OF FRAME REAR OF BASE
3/8" - 1/2" FRAME GROUTING
BASE FRAME
inch mm NON SHRINK
COMPACTED
FILL DIRT
34 1/16"
86.5 cm
31 9/16"
80.7 cm
7 7/8"
20 cm
FRAME
3 15/16"
10.0 cm
9"
22.9 cm
OVERHEAD VIEW
35 15/16"
91 cm 10 5/8"
27.0 cm
10 5/8"
27.0 cm
7 7/8"
20 cm
35 9/16"
90.3 cm
FRONT
1. This machine is intended for installation on a "slab on grade" foundation. Installation is not recommended for elevated
floors unless special consideration is given to provide proper structural support.
2. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-56 for machine loads.
3. For planning purposes a minimum concrete foundation would be 9" thick and 6'-6"x6'-6" (or equivalent area) with
1/2" reinforcing bars at 12" centers each way. Multiple machine installation would have equivalent foundation sizes.
4. Anchor bolts should be embedded in foundation 7". A template is provided with each washer. For this model for locating
the anchor bolts.
5. The machine needs to be set level and the entire base fully supported with non-shrink grout, or shims.
6. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
7. Recommended 4" space between machines. 24" service area needs to be provided at the rear of machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFX50 07/02 3-56
MFX50
1. Dry Weight Capacity 50 lbs. Machine dry weight capacity in pounds
22.7 kg
3. Extract G-Force 235 Maximum G-Force, or the force applied to the load at
periphery of cylinder during extraction
1279 lbs.
4. Empty Weight Weight of machine - empty
581.4 kg
5. Weight of Water 125 lbs. Weight of water in the machine at high level when loaded
56.8 kg
6. Maximum Static 1454 lbs. Total static load, combined weight of machine, water and
Load 660.9 kg load
7. Area of Frame Base 8.82' Frame area, the floor space covered by the base of the base
268.8 cm of the machine
8. Static Load Pressure 165 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 2350 lbs. Total dynamic load, G-Force times dry weight capacity times
1068.2 kg 20% out-of-balance
10. Dynamic Load 266 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 12.50 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 3679 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 8093.8 kg weight capacity and dynamic load
13. Minimum Vertical -1021 lbs. Minimum vertical load, dynamic load subtracted from empty
Load -464.1 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 2350 lbs. Maximum lateral load, acts horizontally along a line of action
Load 1068.2 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 3.18' Height of the basket centerline above floor, line of action of
Centerline 96.9 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 7473 Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
Models 70 7/8"
MFX80 180 cm
29 1/4"
Non-Cabinet 74 cm
10 7/16"
26.5 cm
OPL 49"
124.5 cm
48 7/16"
123 cm DRAIN
56 5/16" OUTLETS
143 cm
FRONT VIEW SIDE VIEW BACK VIEW
WHITE GALLONS
MFX80 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL GALLONS
HOT 18.5 20.4 - - - - 38.9
COLD 18.5 - 46.2 59.4 60.7 52.8 237.6
276.5
WHITE LITERS
MFX80 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL LITERS
HOT 70.1 77.3 - - - - 147.4
COLD 70.1 - 175.1 225.1 230 200.1 900.5
1047.9
*Water use can vary due to custom programming.
COLORS GALLONS
MFX80 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL GALLONS
HOT - 10.2 - - - - 10.2
COLD 37 10.2 46.2 59.4 60.7 52.8 266.3
276.5
WHITE LITERS
MFX80 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL LITERS
HOT - 38.6 - - - - 38.6
COLD 140.2 38.6 175.1 225.1 230 200.1 1009.3
1047.9
*Water use can vary due to custom programming.
ELECTRICAL REQUIREMENTS
• 208 / 240 volt, three phase, 60 Hz, 20 amp circuit breaker, minimum wiring size awg. 12 of
copper wire only.
• Individual branch circuit serving only the washer recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
ANCHOR Bolt should protrude 2 1/8” out of INSTALLATION OF MACHINE ANCHOR BOLTS
GROUT FULL DRAIN OPENING IN
BOLT SIZE cement pad plus grout thickness. WIDTH OF FRAME REAR OF BASE
3/8" - 1/2" FRAME GROUTING
BASE FRAME
inch mm NON SHRINK
COMPACTED
FILL DIRT
2 1/2"
6.3 cm
FRAME
10 3/4"
27.3 cm
11 1/4"
OVERHEAD VIEW
28.5 cm
48 1/2"
123.2 cm
10 3/4"
HOPPER
27.3 cm
10 3/4"
27.3 cm
2 1/2"
6.3 cm
48 15/16" 4 1/4"
124.3 cm 10.8 cm
FRONT
1. This machine is intended for installation on a "slab on grade" foundation. Installation is not recommended for elevated
floors unless special consideration is given to provide proper structural support.
2. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-61 for machine loads.
3. For planning purposes a minimum concrete foundation would be 12" thick and 6'-6"x6'-6" (or equivalent area) with
1/2" reinforcing bars at 12" centers each way. Multiple machine installation would have equivalent foundation sizes.
4. Anchor bolts should be embedded in foundation 9". A template is provided with each washer. For this model for locating
the anchor bolts.
5. The machine needs to be set level and the entire base fully supported with non-shrink grout, or shims.
6. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
7. Recommended 4" space between machines. 24" service area needs to be provided at the rear of machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFX80 07/02 3-61
MFX80
1. Dry Weight Capacity 80 lbs. Machine dry weight capacity in pounds
176 kg
3. Extract G-Force 250 Maximum G-Force, or the force applied to the load at
periphery of cylinder during extraction
1962 lbs.
4. Empty Weight Weight of machine - empty
4316.4 kg
5. Weight of Water 177 lbs. Weight of water in the machine at high level when loaded
389.4 kg
6. Maximum Static 2214 lbs. Total static load, combined weight of machine, water and
Load 4870.8 kg load
7. Area of Frame Base 16.48' Frame area, the floor space covered by the base of the base
502.3 cm of the machine
8. Static Load Pressure 134 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 3750 lbs. Total dynamic load, G-Force times dry weight capacity times
8250 kg 20% out-of-balance
10. Dynamic Load 228 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 11.67 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 5787 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 12731.4 kg weight capacity and dynamic load
13. Minimum Vertical -1713 lbs. Minimum vertical load, dynamic load subtracted from empty
Load -3768.6 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 3750 lbs. Maximum lateral load, acts horizontally along a line of action
Load 8250 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 3.31' Height of the basket centerline above floor, line of action of
Centerline 100.9 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 12413 Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)
Washers 18 1/2"
WATER
CONNECTIONS
CONNECTION
18 1/2"
BACK VIEW
OPL
*a minimum of 18" is recommended above
washer to raise hinged top for service
WHITE GALLONS
MFX100 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL GALLONS
HOT 22.7 25.6 - - - - 48.3
COLD 22.7 - 56.8 42.9 74.6 64.8 291.8
340.7
WHITE LITERS
MFX100 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL GALLONS
HOT 86 97 - - - - 183
COLD 86 - 215.3 162.6 282.7 245.6 1105.9
1291.2
*Water use can vary due to custom programming.
COLORS GALLONS
MFX100 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL GALLONS
HOT - 72.8 - - - - 72.8
COLD 45.4 72.8 56.8 72.9 74.6 64.8 327.3
340.7
COLORS LITERS
MFX100 PREWASH WASH RINSE 1 R2 R3 R4 TOTAL TOTAL GALLONS
HOT - 275.9 - - - - 275.9
COLD 172 275.9 215.3 276.3 282.7 245.6 1240.5
1291.2
*Water use can vary due to custom programming.
ELECTRICAL REQUIREMENTS
• 208 / 240 volt, three phase, 60 Hz, 30 amp circuit breaker, minimum wiring size awg. 10 of
copper wire only.
• Individual branch circuit serving only the washer recommended.
• Washer must be grounded in accordance to National Electrical Codes and local codes and
ordinances.
• Three phase hookups require 4 wires. (3 wires plus ground)
• Line 1 • Line 2 • Line 3 • Earth Ground
ANCHOR Bolt should protrude 2 1/8” out of INSTALLATION OF MACHINE ANCHOR BOLTS
GROUT FULL DRAIN OPENING IN
BOLT SIZE cement pad plus grout thickness. WIDTH OF FRAME REAR OF BASE
3/8" - 1/2" FRAME GROUTING
BASE FRAME
inch mm NON SHRINK
COMPACTED
FILL DIRT
2 1/2"
6.3 cm
FRAME
10 3/4"
27.3 cm
11 1/4"
OVERHEAD VIEW
28.5 cm
48 1/2"
123.2 cm
10 3/4"
HOPPER
27.3 cm
10 3/4"
27.3 cm
2 1/2"
6.3 cm
48 15/16" 4 1/4"
124.3 cm 10.8 cm
FRONT
1. This machine is intended for installation on a "slab on grade" foundation. Installation is not recommended for elevated
floors unless special consideration is given to provide proper structural support.
2. A properly designed and installed foundation must be provided to support the machine. Consideration needs to be given
to existing soil conditions. See page 3-66 for machine loads.
3. For planning purposes a minimum concrete foundation would be 12" thick and 6'-6"x6'-6" (or equivalent area) with
1/2" reinforcing bars at 12" centers each way. Multiple machine installation would have equivalent foundation sizes.
4. Anchor bolts should be embedded in foundation 9". A template is provided with each washer. For this model for locating
the anchor bolts.
5. The machine needs to be set level and the entire base fully supported with non-shrink grout, or shims.
6. The room ceiling height should not be less then 96" from the top of the foundation for servicing the equipment.
7. Recommended 4" space between machines. 24" service area needs to be provided at the rear of machine.
COMMERCIAL FRONT LOAD WASHERS - MODELS MFX100 07/02 3-66
MFX100
1. Dry Weight Capacity 100 lbs. Machine dry weight capacity in pounds
220 kg
3. Extract G-Force 200 Maximum G-Force, or the force applied to the load at
periphery of cylinder during extraction
2072 lbs.
4. Empty Weight Weight of machine - empty
4558.4 kg
5. Weight of Water 229 lbs. Weight of water in the machine at high level when loaded
503.8 kg
6. Maximum Static 2396 lbs. Total static load, combined weight of machine, water and
Load 5271.2 kg load
7. Area of Frame Base 16.48' Frame area, the floor space covered by the base of the base
502.3 cm of the machine
8. Static Load Pressure 145 Static load pressure, total static load divided by the frame
lbs./sq. ft. area
9. Total Dynamic Load 3800 lbs. Total dynamic load, G-Force times dry weight capacity times
8360 kg 20% out-of-balance
10. Dynamic Load 231 Dynamic load pressure, dynamic load divided by frame area
Pressure - lbs.
11. Dynamic Load 10.42 Dynamic load frequency, load cycles per second
Frequency - Hz
12. Maximum Vertical 5967 lbs. Maximum vertical load, either sum of empty weight, dry-
Load 3127.4 kg weight capacity and dynamic load
13. Minimum Vertical -1633 lbs. Minimum vertical load, dynamic load subtracted from empty
Load -3592.6 kg weight and dry-weight capacity, note that a negative value
means the load acts upward
14. Maximum Lateral 3800 lbs. Maximum lateral load, acts horizontally along a line of action
Load 8360 kg that passes through the centerline of the basket. Assumes
an imbalanced load equal to 20% of rated capacity rotating
at maximum RPM
15. Height of Basket 3.31' Height of the basket centerline above floor, line of action of
Centerline 100.9 cm lateral load, if elevated base or pad is used, add base or pad
height to basket center line height to get overall height
16. Maximum Moment 12578 Maximum moment about machine base, the “torque” caused
About Machine Base by the lateral load (maximum lateral load times the height of
- lbs.-ft. the basket centerline)