Professional Documents
Culture Documents
G190ean01 0
G190ean01 0
G190ean01 0
0
AU OPTRONICS CORPORATION
Checked &
Customer Date Date
Approved by
Approved by Prepared by
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
Record of Revision
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
Contents
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of LED light bar edge. Instead, press at the far ends of
LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even
momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD module
should be supplied by power complied with requirements of Limited Power Source (IEC60950 or
UL1950), or be applied exemption.
13) Avoid stressing front bezel position when doing mechanical design.
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
2. General Description
G190EAN01.0 is a Color Active Matrix Liquid Crystal Display composed of a TFT-LCD panel, a driver circuit,
and a backlight system. The screen format is intended to support the SXGA (1280(H) x 1024(V)) screen and
16.7M colors. All input signals are 2-channel LVDS interface compatible.
Power Consumption [Watt] LED: 14.4 (W) + LVDS: 3.5 (W) (typ)
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
Rising - 13 18
Optical Response Time [msec] Falling - 12 17 4, 6
Rising + Falling -- 25 35
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
10 %
50 %
90 %
Note 3: The luminance uniformity of 9 points is defined by dividing the maximum luminance values by the
minimum test point luminance. And measured by TOPCON SR-3
Minimum Luminance of 9 points
!W9 =
Maximum Luminance of 9 points
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
Photo detector
Field=2!
50 cm
Where
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
% Tr F TrR
100
90
Optical
White Black White
response
10
0
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
ASIC G1024
Timing
LVDS Controller TFT-LCD
Connector
LVDS 1280*(3)*1024
Receiver
RSDS Pixels
Transmitter
X-Driver IC
+ 5V G1
D1 D3840
LED B/L
DC/DC Gamma
Converter Correction
(Integrate
level shift)
DC POWER
LED driver
Mating Type:
FI-X30HL (Locked Type)
FI-X30H (Unlocked Type)
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows:
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
G
C1
1uF/16V
(High to Low)
D1
D2
D5
D6
Control
Signal R2
Q3
AO6402
G
1K
C3 S
2
+12.0V
SW1
SW MAG-SPST VR1 0.01uF/25V
1
47K
C2
1uF/25V
90% 5.0V
10%
0V
470 us
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
- - - Volt
o
VF LED Forward Voltage - 3.2 3.6 Volt IF =80 mA, Ta = 25 C
- - -
LED Power IF =80 mA, Ta = 25oC
PLED - 13.8 15.6 Watt
Consumption
LED Lifetime 50,000 Hrs IF=80 mA, Ta= 25oC
Note 2: VCC, Ivcc, PVCC , Irush LED are defined for LED B/L.(100% duty of PWM dimming)
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
1 2 1279 1280
1st Line R GB R GB R GB R GB
1024th Line R GB R GB R GB R GB
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
Note1: Normally DE mode only. VS and HS on EVEN channel are not used.
Note2: Please follow VESA.
Note3: 8-bit in
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
Connector
1 30
RxOIN0-
VCC
Note2: Input signals of odd and even clock shall be the same timing.
Note3: Please follow VESA.
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
www.avnet-embedded.eu
www.avnet-embedded.eu
G190EAN01.0
21/28
Tv
Vsync
PWvs
Hsync
Product Specification
N 1 2 3 4 N
Invalid Data Invalid Data
RGB Data
Line Line Line Line Line Line
CLK
Tclk
Hsync
PWhs
Tbp(h) Tfp(h)
DE
Tdisp(h)
6.4.2 Timing Diagram
RGB Data Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
Invalid Data Invalid Data
(Odd) 1 3 5 7 9 11 M-5 M-3 M-1
RGB Data
T2 30 40 50
T3 200 - --
T4 0.5 - 10
T5 10 - -
T6 10 - -
T7 0 - - ms
T8 10 - -
T9 - - 10
T10 110 - -
T11 0 16 50
T12 0 10
T13 1000 - -
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
FI-X30HL
Mating Housing Part Number
FI-X30H (Unlocked Type)
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
Manufacturer STM
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
8. Reliability Test
Environment test conditions are listed as following table.
Items Required Condition Note
o
Temperature Humidity Bias (THB) Ta= 50 C, 80%RH, 300hours
High Temperature Operation (HTO) Ta= 50oC, 300hours
Low Temperature Operation (LTO) Ta= 0oC, 300hours
High Temperature Storage (HTS) Ta= 60oC, 300hours
Low Temperature Storage (LTS) Ta= -20oC, 300hours
Acceleration: 1.5 G
Vibration Test Wave: Random
(Non-operation) Frequency: 10 - 200 - 10 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)
Acceleration: 50 G
Shock Test Wave: Half-sine
(Non-operation) Active Time: 20 ms
Direction: !X," !Y," !Z (one time for each Axis)
Operation:10,000 ft
Altitude Test
Non-Operation:30,000 ft
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
-20oC to 60oC, and back again. Power is not applied during the test. After temperature cycling, the
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost.
Self-recoverable. No hardware failures.
Note 3:
! Water condensation is not allowed for each test items.
! Each test is done by new TFT-LCD module. Don’t use the same TFT-LCD module repeatedly for
reliability test.
! The reliability test is performed only to examine the TFT-LCD module capability.
! To inspect TFT-LCD module after reliability test, please store it at room temperature and room humidity
for 24 hours at least in advance.
! No function failure occurs.
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
G190EAN01.0
Note 2: For RoHS compatible products, AUO will add for identification.
Note 3: For China RoHS compatible products, AUO will add for identification.
Note 4: The Green Mark will be presented only when the green documents have been ready by AUO Internal
Green Team.
9.2 Packaging
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
www.avnet-embedded.eu
Product Specification G190EAN01.0
AU OPTRONICS CORPORATION
www.avnet-embedded.eu