Professional Documents
Culture Documents
Elgine Whirlwind MV Series Specs
Elgine Whirlwind MV Series Specs
Elgine Whirlwind MV Series Specs
Efficient airflow management is fundamental to • The unique ability to move more air at higher
sweeper performance and at the heart of the velocities, creating greater vacuum to "pull"
Whirlwind. Vacuum sweepers use high velocity material through the system, for one pass
air to create suction that picks material off paved pickup and elimination of plugging that can
surfaces and carries it into the hopper. Effective occur in other similar type sweepers.
airflow is determined by the vacuum source and • An aerodynamic 'scoop' deflector which
a properly designed air routing path. The smoothly transitions air from the confined
Whirlwind’s airflow system includes: space of the inlet tube to the open hopper -
• A powerful, nine vane closed face turbine fan minimizing pressure loss and maximizing
powered by an efficient and powerful turbo- sweep performance.
charged diesel auxiliary engine. The key Air Flow System components include:
• Impeller (Fan)
• Auxiliary Engine
Impeller
The unique, closed unsurpassed sweeping performance. The larger
face, 9 vane, 797 mm capacity impeller allows for more pressure in the
(31 3/8 in), abrasion suction nozzle as well as more vacuum in the
resistant steel impeller hopper. Closed face design, while more difficult
generates the to manufacture provides more efficient
necessary airflow. performance than comparable open-face fans.
Designed especially for The impeller is fully balanced for longevity of
applications that fan and bearing life. High air flow and vacuum
require maximum allows sweeping at lower engine RPM for lower
airflow, the impeller is sound levels and less fuel consumption that
wider and larger in other similar models.
diameter than most
standard impellers. The impeller is driven by a five "V" groove power
The high velocity belt for maximum performance and simplicity of
turbine fan is rated at 20,000 CFM (562 m 3/min) construction, with simple tension adjustment
(rated by an independent test facility) for not requiring repositioning of the engine. It is
2
mounted and supported on both sides by heavy- housing or look into the air exhaust opening. It
duty bearings capable of being greased from the is not an integral part of the hopper, which
ground level, without tilting the hopper. It is facilitates service or replacement of necessary.
also protected from the elements by an
Specifications
enclosure system.
Blower
Drive: Fluid coupler and 5-groove banded power belt
The blower housing is constructed of 3.42mm with adjustable idler pulley
(10 gauge) abrasion resistant steel and lined with Speed: 3400 RPM
rubber for maximum extended wear in abrasive Blower Rating: 20,000 CFM (562 m3/min.)
environments. The blower housing has an @4000 RPM
Blower Construction: Abrasion resistant steel
inspection door for quick inspections Blower Housing: 10 gauge (3.4 mm) steel, linatex lined for
eliminating the need to remove the blower extended wear
Auxiliary Engine
An auxiliary engine drives the impeller to create
the vacuum and power the hydraulic, water, and
electrical systems. Having a separate auxiliary
engine for sweeper functions allows increased
suction power, since 100% of the engine horse
power is dedicated to sweeping and not
transporting. The chassis engine delivers the
transport power, unlike single engine units
where power for transport and power for
sweeping must be divided from the single
engine. The availability of two engines is
especially important given any variations in
sweeping grade or payload levels. The sweeper's
auxiliary engine continues to perform
consistently, oblivious to changes in grade or
payload. A single engine will need to divert
more power to transport and less to sweeping
when changes occur.
3
Productive Sweep System
The Whirlwind sweep system includes a suction
nozzle, trailing arm side broom(s) and a centrally
mounted extension broom. Working together,
these components move material into a large
debris hopper.
Suction Nozzle
You can choose disconnect allows an operator to inspect and
between a single clean the hose intake tube without raising the
762 mm (30 inch) hopper.
abrasion-resistant
suction nozzle or An integral automatic “jackknife style” gate valve
dual nozzles. is bolted on the top of the suction hose where
Each suction the material enters the hopper. The gate valve
nozzle covers a is automatically activated with the suction
pick-up area of nozzle activation and prevents material from
174 sq/in (metric) dropping back down the nozzle tubes when
and extends 381 the vacuum is stopped. The gate valve also
mm (15 inches) prevents material/debris from being dropped
beyond the track into the suction nozzle when the sweeper is
of the tire for in travel mode.
increased
performance Specifications
closer to the curb. The 279 mm (11 inch) Vacuum Nozzle and Hoses
suction hose accepts large debris. The suction Nozzle Width 30 in. (762 mm)
nozzle rides on two heavy-duty pivoting caster Pickup Area 174 in2 (1119 cm2)
wheels. This allows the nozzle to move Construction Abrasion resistant steel components
Hose Connection Quick disconnect type at
sideways, better staying in the path of the debris lower area near vacuum nozzle
and following road contours as well as improve Hose Construction Flexible rubber, steel reinforced
the service life. Hose 11 in. (280 mm) inside diameter
The suction nozzle is equipped with a front All primary metal components such as nozzle
mounted shutter that allows easy entry of larger and tube connection are constructed of abrasion
objects and large quantities of leaves. Quick resistant steel for longer life in an abrasive
environment.
4
Trailing Arm Side Brooms
You can choose between 711 mm (28 inch) or broom tilt allow adjusting for changing
914 mm (36 inch) diameter greaseless trailing conditions on the street and adjusts for wear
arm side brooms that can be operated compensation. The side brooms are
individually or simultaneously for the widest pneumatically raised and lowered and suspended
sweeping path in the industry, up to a full 3658 on by heavy duty pneumatic cylinders that are
mm (12 feet). The hydraulically driven, full common with other pneumatic cylinders on the
floating, trailing arm design features inward sweeper for ease of service.
motion safety to prevent damage when sweeping
and encountering a fixed obstacle. In-cab Chassis requirements based on side brooms:
control of down pressure and the optional
• 771 mm (28”) steel disc, oil tempered steel
wire on 3378 mm (133”) Cab-over
• 914 mm (36”) steel disc, oil tempered steel
wire on 3861 mm (152”) Co & FL70
Conventional Chassis
Specifications
Side Broom
Diameter:
28 in (711 mm) on 133” WB Sterling SC8000
36 in (914 mm) on 152” WB Sterling SC8000
36 in (914 mm) on 164” WB Freightliner M2
Disc Construction: Steel plate
Speed: Constant
Drive: Hydraulic motor, protected by relief valve
Mounting: Free floating trailing arm
Motion: Pneumatically inward/outward, raised/lowered
Tilt Adjustment: Inward/outward, forward/backward
Digging Pressure/Wear Control: Pneumatic in cab
Type: Segment set disposable
Materia:l Oil tempered steel wire
Extension Broom
Diameter: 16 in. (406 mm)
Length: 54 in. (1372 mm)
Speed: Constant
Drive : Hydraulic motor, protected by relief valve
Digging Pressure/Wear Control: Pneumatic outside cab
Lift Control: Pneumatic from control panel duty pneumatic cylinder. Rotation stops and the
Type: Polypropylene prefab, disposable
Location: Center of sweeper broom lifts automatically when the sweeper is
put into reverse or in the transport mode.
5
Hopper
6
Subcomponents of Sweep System
Hydraulics
The hydraulic system, including tandem Specifications
hydraulic pumps, provides power to operate the
side broom motors, the suction nozzle Hydraulic System
Purpose: Powers hydraulic motors on side broom, extension
movement, hopper tilting and door activation. broom, and hopper cycle
It is driven by a maintenance free direct gear Hydraulic Pump Capacity 8.3 GPM (31 LPM) @ 2500 RPM,
pump. The flow capacity is 31 LPM (8.3 GPM) @ each section (16.6 GPM Total)
2500 RPM. The reservoir capacity is 87 L (23 Hydraulic Pump Direct gear driven, tandem type
Reservoir Capacity 23 gal (87 L)
gallons) and has an exterior sight gauge. The Filter 10 micron, spin-on type with in-cab restriction indicator
reservoir is located in the enclosed auxiliary
engine compartment for quick inspection
without tilting the hopper. All circuits have potential leaks, all high pressure fittings are "O"
quick disconnect pressure check ports for easy ring type. A 10-micron spin-on hydraulic filter
maintenance. To minimize the hazards of provides the filtration for the system.
Pneumatics
The pneumatics control the in and out and up Specifications
and down of the side brooms, suction nozzles
and extension broom. They are also used to Pneumatic System
Features: PR4 type pressure protector for chassis air system
oscillate the extension broom R-L and to control Cylinders: Rated 250 PSI, seperate rod on seals and wipers to
the extension broom down pressure. The air prevent contamination.
lines are all color coded and function stamped
for easy maintenance. The Whirlwind
pneumatic system features a PR4 type pressure PSI with separate rod seals and wipers to prevent
protector for the chassis air system to protect it contamination from entering them. Each
at air pressures below 85 PSI. A separate air tank cylinder is controlled by a single two-position
for all sweeper air components is provided. The solenoid valve mounted on a manifold with a
cylinders are interchangeable and rated at 250 common input and exhaust.
Electrical
The Whirlwind’s electrical system is independent In addition, all hydraulic and pneumatic valves
from the chassis electrical system. The sweeper are electrical with the exception of the hopper
engine has one 925 CCA, 12-volt battery with a lift and door.
120-amp alternator. Accessories powered by the
electrical system include: an electronic back-up The sweeper
alarm for additional warning and safety when harnesses are color-
the chassis is in reverse, sweeper lighting - rear coded and hot
identification lights, side broom and rear stamped with
clearance lights, sweeper warning lights - hopper appropriate word
up, hopper full load and hopper rear door open. designation labeled
every four inches
Specifications (i.e. ignition, side
broom) on each
Electrical System wire. For safety
Alternator: 120 amperes and ease of
Battery: 12 volt, 925 CCA maintenance all
Lights : Side broom, rear clearance, rear identification
Reversing Safety: Electric back-up alarm, sweep components raise electrical circuits
automatically are protected by
Circuit Breaker:s Manual reset circuit breakers.
Wiring Harnesses: Color coded, function stamped and labeled Should an electrical problem occur, the breakers
every 4 in (100mm)
do not need to be replaced, simply reset.
7
Controls
Control of all sweeping functions, spray water includes a gauge package that allows the
and lighting is accomplished using simple operator to view all-important auxiliary engine
conventional rocker switch controls located on a information from either operating position.
stationary central console that allows for use Sweeper engine instrumentation includes a
from either right or left positions. The console tachometer, hour meter, oil pressure, fuel,
voltage, and coolant temperature for complete
information for the operation on the condition
of the auxiliary engine. The controls for
auxiliary engine ignition and throttle, side
broom down pressure and manual reset circuit
breakers are located in the control console
pedestal for quick and easy service of the system.
8
There are two (2) spray nozzles located at each extension broom. One pump is dedicated
side broom and seven (7) removable water spray exclusively to each side: one for the RH suction
nozzles inside each suction nozzle. The nozzle and RH side broom, the other for the LH
extension broom is supplied with four (4) rubber suction nozzle and LH side broom. These pumps
mounted, quick disconnect spray nozzles for can be selectively controlled from in the cab to
easy cleaning and maintenance. adjust to the sweeping conditions. The filters
located at each pump are accessible without
The spray system is powered by two electric 12 raising the hopper and are easy to clean. Ball
volt diaphragm type water pumps each valves at each pump allow cleaning of the filters
providing 15 LPM (4 GPM) and 2.8 Bar (40 PSI) without the loss of water from the tank.
to the suction nozzle, the side broom and the
9
Versatile Chassis System
The Whirlwind can be mounted on a • 771 mm (28”) steel disc, oil tempered steel
conventional or cab-over chassis for versatility wire on 3378 mm (133”) Cab-over *
and a high level of driver comfort and safety. • 914 mm (36”) steel disc, oil tempered steel
Side broom dimension choice may determine wire on 3861 mm (152”) Co & FL70
what chassis is best. Conventional Chassis **
**
Vehicle width 96 in. (2438 mm) Vehicle width 96 in. (2438 mm) Vehicle width 96 in. (2438 mm)
102 in. (2591 mm) 122 in. (3099 mm)
91 in. (2311 mm)
125 in. (3175 mm)
125 in. (3175 mm)
126 in. (3200 mm)
164 in. (3988 mm) 133 in. (3378 mm) 152 in. (3860 mm)
245 in. (6045 mm) 233 in. (5918 mm) 252 in. (6400 mm)
10
Customization System (Optional Equipment)
Understanding that each sweeping operation is
unique, the Whirlwind was designed with several
unique options that allow the machine to be
built to the customers specific needs. Some of
these options include:
• Wandering Hose with Hydraulic Assisted Boom • 7.6 meter (10 cubic yard hopper)
• High Pressure Water Pump • In cab hopper dump
• Hopper Deluge System • Front spray bar
• Side Broom Tilt • Polyurethane Hopper liner
• Auxiliary Hydraulic Pump • High pressure wash down
• Auto-nozzle shutter
Consult factory for additional options.
LifeLiner™ NEW!
Lifel iner
LifeLiner™ is a metal has been prepared, a polyester primer and
specially topcoat are baked on. Once the outside coating
designed hopper process is complete, a polyurethane hopper liner
system that material that has been developed specifically for
greatly improves Elgin is applied to all inside surfaces of the
the life, hopper to protect against wear and corrosion.
durability, and This proprietary polyurethane coating is more
functionality of a wear resistant than stainless steel and extremely
sweeper hopper. The LifeLiner system begins resistant to most chemicals. LifeLiner is
with special preparation of the steel that allows extremely smooth and slick making dumping
the liner to permanently bond. After the base and cleanup easier.
11