Professional Documents
Culture Documents
M185XW01 V6
M185XW01 V6
M185XW01 V6
AU OPTRONICS CORPORATION
( ) Preliminary Specification
( V ) Final Specification
Approved by Prepared by
Contents
Record of Revision
1.0 2009/7/2 5
2.1 Display Characteristics 2.1 Display Characteristics
Weight Weight
1330 1330 50g
1.0 2009/7/2 10
I/F PCB Interface: I/F PCB Interface:
FI-XB30SSRL-HF16(JAE)/MSCKT2407P30HB( ) FI-XB30SRL-HF11(JAE) / 093F30-B0T01A(CHIEF
LAND)
1.0 2009/7/2 11
4.2 Backlight Unit 4.2 Backlight Unit
LED current LED current
Min:n/a Max:20 Min: 19 Max:21
1.0 2009/7/2 12
5.1.1 Power Specification 5.1.1 Power Specification
Input Current Input Current
Typ:0.6 Max:0.7 Typ:0.84 Max:1
Allowable Logic/LCD Drive Ripple Voltage Allowable Logic/LCD Drive Ripple Voltage
Max:200 Max:350
1.0 2009/7/2 14 5.2 Backlight Unit 5.2 Backlight Unit
LED Operation Current LED Operation Current
Min:n/a Typ:n/a Max:20 Min:19 Typ:20 Max:21
LED Operation Voltage LED Operation Voltage
Typ:42.9 Max:44.2 Typ:44.8 Max:47.6
BLU Power consumption BLU Power consumption
Typ:5.5 Max:5.7 Typ:5.4 Max:6.0
LED life Time LED life Time
Typ:n/a Typ:25,000
1.0 2009/7/2 18 6.3 Signal Description 6.3 Signal Description
Signal Drawing Signal Drawing
Plus FFC drawing Remove FFC drawing
1.0 2009/7/2 19 H-section H-section
Blanking Blanking
Min:50 Min:104
Period Period
Min:1482 Min:1470
Note2 : Note2 :
Clock Frequency 90MHz(Max.)= 1416(H)*847(V)*75Hz Clock Frequency 90MHz(Max.)=
1470(H)*816(V)*75Hz
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken
out from the container, do not press the center of the LED lightbar edge. Instead, press at the
far ends of the LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT
Module may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
Photo detector
Measured distance
100
90
Optical
W hite Black Black W hite
response
10
0
1 Frame 1 Frame
CT = | YB – YA | / YA ! 100 (%)
Where
RGBRGB
Gray Level = L127
RGBRGB
Gray Level = L0
RGBRGB
Amplitude
AC
DC
Time
AC Level(at 30 Hz)
Flicker (dB) = 20 log
DC Level
AUO G1
ASIC
Y-Driver IC
Timing
LVDS Controller
LVDS TFT-LCD
Receiver
1366(x3) x 768
Connector
RSDS
Transmitter Pixels
+5V X-Driver IC
G768
D1 D4098
LED
Gamma
DC/DC
Correction
Converter
I/F + X-PCB
DC
Driver
C1
1uF/16V
(High to Low)
D1
D2
D5
D6
Control
Signal Q3
R2 AO6402
G
1K
S
C3
2
+12.0V
SW1
SW MAG-SPST VR1 0.01uF/25V
1
47K
C2
1uF/25V
VTH
VID
VTL
VICM
VSS
[Hour]
LTLED LED life Time 25,000 30,000 --
Note 2
Note 1 : The value showed in the table is one light bar’s operation voltage.
Note 2 : Based on the operating current is 20mA.
1 2 1365 1366
1st Line R G B R G B R GB R G B
768 Line R G B R G B R GB R G B
1 30
VCC
-
NC
!"#$%&'
!"#$%&' Item Symbol Min Typ Max Unit
Period Tv 776 808 1023 Th
Active Tdisp(v) 768 768 768 Th
V-section Blanking Tblk(v) 8 40 255 Th
Period Th 1470! 1606 2047 Tclk
Active Tdisp(h) 1366 1366 1366 Tclk
H-section Blanking Tblk(h) 104! 240 681 Tclk
Period Tclk - 12.8 - ns
(&)*+'
(&)*+' Frequency Freq - 78 90 MHz
,-%./'0%1/'
,-%./'0%1/' Frame Rate F 50 60 75 Hz
Value
Parameter Unit
Min. Typ. Max.
T1 0.5 - 10 [msec]
T2 0 40 50 [msec]
T3 200 - - [msec]
T4 200 - - [msec]
T5 0.5 16 50 [msec]
T6 - - 100 [msec]
T7 1000 - - [msec]
Acceleration: 50 G
Shock Test Wave: Half-sine
(Non-operation) Active Time: 20 ms
Direction: X, Y, Z (one time for each Axis)
Drop Test Height: 60 cm, package test
Thermal Shock Test (TST) -20 /30min, 60 /30min, 100 cycles 1
On/Off Test On/10sec, Off/10sec, 30,000 cycles
Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec,
8 points, 25 times/ point.
ESD (Electro Static Discharge) 2
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec
8 points, 25 times/ point.
Operation:10,000 ft
Altitude Test
Non-Operation:30,000 ft
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
-2"# to 6"#, and back again. Power is not applied during the test. After temperature cycling, the
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: EN61000-4-2, ESD class B: Certain performance degradation allowed
No data lost
Self-recoverable
No hardware failures.
Note 2: For RoHS compatible products, AUO will add for identification.
Note 3: For China RoHS compatible products, AUO will add for identification.
Note 4: The Green Mark will be presented only when the green documents have been ready by
AUO Internal Green Team.
Ver 1.1
Ver 1.1