Professional Documents
Culture Documents
Hilti Outrigger
Hilti Outrigger
Hilti Outrigger
8
Company: PT QUADRAN EMPAT PERSADA Page: 1
Specifier: Project: MINING ESCAVATION
Address: Fastening Point: Combat 42m Medium
Phone I Fax: | Date: 28/05/2022
E-Mail:
Specifier's comments:
1 Input data
Anchor type and size: HIT-RE 500 V3 + HAS-U 5.8 M16
Effective embedment depth: hef,act = 100 mm (hef,limit = - mm)
Material: 5.8
Approval No.: ESR-3814
Issued I Valid: 01/01/2019 | 01/01/2021
Proof: Design method ACI 318-11 / Chem
Stand-off installation: eb = 0 mm (no stand-off); t = 10 mm
Baseplate: lx x ly x t = 580 mm x 580 mm x 10 mm; (Recommended plate thickness: not calculated
Profile: Square hollow, 100 x 100 x 3,6; (L x W x T) = 100 mm x 100 mm x 4 mm
Base material: cracked concrete, C30/37, fc' = 4,351 psi; h = 400 mm, Temp. short/long: 30/30 °C
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: tension: condition B, shear: condition B; no supplemental splitting reinforcement present
edge reinforcement: none or < No. 4 bar
R
- The anchor calculation is based on a rigid baseplate assumption.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.8.8
Company: PT QUADRAN EMPAT PERSADA Page: 2
Specifier: Project: MINING ESCAVATION
Address: Fastening Point: Combat 42m Medium
Phone I Fax: | Date: 28/05/2022
E-Mail:
3 Tension load
Load Nua [kN] Capacity f Nn [kN] Utilisation bN = Nua/f Nn Status
Steel failure* 10.973 51.025 22 OK
Bond failure** 43.892 123.555 36 OK
Sustained Tension Load Bond Strength* N/A N/A N/A N/A
Concrete cone failure** 43.892 101.312 44 OK
* most unfavourable anchor **anchor group (anchors in tension)
Variables
Ase,N [mm2] futa [N/mm2]
157 500.00
Calculations
Nsa [kN]
78.500
Results
Nsa [kN] f steel f Nsa [kN] Nua [kN]
78.500 0.650 51.025 10.973
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.8.8
Company: PT QUADRAN EMPAT PERSADA Page: 3
Specifier: Project: MINING ESCAVATION
Address: Fastening Point: Combat 42m Medium
Phone I Fax: | Date: 28/05/2022
E-Mail:
Nag = (AA ) y
Na
Na0
ec1,Na y ec2,Na y ed,Na y cp,Na Nba ACI 318-11 Eq. (D-19)
f Nag ≥ Nua ACI 318-11 Table D.4.1.1
ANa = see ACI 318-11, Part D.5.5.1, Fig. RD.5.5.1(b)
ANa0 = (2 cNa)2 ACI 318-11 Eq. (D-20)
cNa = 10 da √ t uncr
1100
ACI 318-11 Eq. (D-21)
( )
1
y ec,Na = e' ≤ 1.0 ACI 318-11 Eq. (D-23)
1+ N
cNa
y ed,Na = 0.7 + 0.3 ( ) ca,min
cNa
≤ 1.0 ACI 318-11 Eq. (D-25)
y cp,Na = MAX ( )
ca,min cNa
,
cac cac
≤ 1.0 ACI 318-11 Eq. (D-27)
Nba = l a · t k,c · p · da · hef ACI 318-11 Eq. (D-22)
Variables
2 2
t k,c,uncr [N/mm ] da [mm] hef [mm] ca,min [mm] aoverhead t k,c [N/mm ]
17.46 16 100 465 1.000 9.45
ec1,N [mm] ec2,N [mm] cac [mm] la
0 0 159 1.000
Calculations
cNa [mm] ANa [mm2] ANa0 [mm2] y ed,Na
242 934,389 233,597 1.000
y ec1,Na y ec2,Na y cp,Na Nba [kN]
1.000 1.000 1.000 47.521
Results
Nag [kN] f bond f Nag [kN] Nua [kN]
190.085 0.650 123.555 43.892
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.8.8
Company: PT QUADRAN EMPAT PERSADA Page: 4
Specifier: Project: MINING ESCAVATION
Address: Fastening Point: Combat 42m Medium
Phone I Fax: | Date: 28/05/2022
E-Mail:
Ncbg = (AA ) y
Nc
Nc0
ec,N y ed,N y c,N y cp,N Nb ACI 318-11 Eq. (D-4)
f Ncbg ≥ Nua ACI 318-11 Table D.4.1.1
ANc see ACI 318-11, Part D.5.2.1, Fig. RD.5.2.1(b)
ANc0 = 9 h2ef ACI 318-11 Eq. (D-5)
( )
1
y ec,N = 2 e'N ≤ 1.0 ACI 318-11 Eq. (D-8)
1+
3 hef
y ed,N = 0.7 + 0.3 (
ca,min
1.5hef )
≤ 1.0 ACI 318-11 Eq. (D-10)
y cp,N = MAX (
ca,min 1.5hef
cac
,
cac )
≤ 1.0 ACI 318-11 Eq. (D-12)
1.5
Nb = kc l a √fc hef
'
ACI 318-11 Eq. (D-6)
Variables
hef [mm] ec1,N [mm] ec2,N [mm] ca,min [mm] y c,N
100 0 0 465 1.000
Calculations
ANc [mm2] ANc0 [mm2] y ec1,N y ec2,N y ed,N y cp,N Nb [kN]
360,000 90,000 1.000 1.000 1.000 1.000 38.966
Results
Ncbg [kN] f concrete f Ncbg [kN] Nua [kN]
155.864 0.650 101.312 43.892
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.8.8
Company: PT QUADRAN EMPAT PERSADA Page: 5
Specifier: Project: MINING ESCAVATION
Address: Fastening Point: Combat 42m Medium
Phone I Fax: | Date: 28/05/2022
E-Mail:
4 Shear load
Load Vua [kN] Capacity f Vn [kN] Utilisation bV = Vua/f Vn Status
Steel failure* 0.496 28.200 2 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout failure (concrete cone relevant)** 1.985 218.210 1 OK
Concrete edge failure in direction y+** 1.985 112.138 2 OK
* most unfavourable anchor **anchor group (relevant anchors)
Variables
Ase,V [mm2] futa [N/mm2]
157 500.00
Calculations
Vsa [kN]
47.000
Results
Vsa [kN] f steel f Vsa [kN] Vua [kN]
47.000 0.600 28.200 0.496
( )
1
y ec,N = 2 e'N ≤ 1.0 ACI 318-11 Eq. (D-8)
1+
3 hef
y ed,N = 0.7 + 0.3 (
ca,min
1.5hef )
≤ 1.0 ACI 318-11 Eq. (D-10)
y cp,N = MAX (
ca,min 1.5hef
cac
,
cac )
≤ 1.0 ACI 318-11 Eq. (D-12)
1.5
Nb = kc l a √fc hef
'
ACI 318-11 Eq. (D-6)
Variables
kcp hef [mm] ec1,N [mm] ec2,N [mm] ca,min [mm]
2 100 0 0 465
Calculations
ANc [mm2] ANc0 [mm2] y ec1,N y ec2,N y ed,N y cp,N Nb [kN]
360,000 90,000 1.000 1.000 1.000 1.000 38.966
Results
Vcpg [kN] f concrete f Vcpg [kN] Vua [kN]
311.728 0.700 218.210 1.985
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.8.8
Company: PT QUADRAN EMPAT PERSADA Page: 6
Specifier: Project: MINING ESCAVATION
Address: Fastening Point: Combat 42m Medium
Phone I Fax: | Date: 28/05/2022
E-Mail:
Vcbg = (AA ) y
Vc
Vc0
ec,V y ed,V y c,V y h,V y parallel,V Vb ACI 318-11 Eq. (D-31)
f Vcbg ≥ Vua ACI 318-11 Table D.4.1.1
AVc see ACI 318-11, Part D.6.2.1, Fig. RD.6.2.1(b)
AVc0 = 4.5 c2a1 ACI 318-11 Eq. (D-32)
( )
1
y ec,V = 2e'v ≤ 1.0 ACI 318-11 Eq. (D-36)
1+
3ca1
y ed,V = 0.7 + 0.3 (ca2
1.5ca1 )
≤ 1.0 ACI 318-11 Eq. (D-38)
y h,V = √
1.5ca1
ha
≥ 1.0 ACI 318-11 Eq. (D-39)
(( ) )
0.2
l 1.5
Vb = 7 e √da l a √f'c ca1 ACI 318-11 Eq. (D-33)
da
Variables
ca1 [mm] ca2 [mm] ecV [mm] y c,V ha [mm]
592 465 0 1.000 400
Calculations
AVc [mm2] AVc0 [mm2] y ec,V y ed,V y h,V Vb [kN]
747,600 1,577,088 1.000 0.857 1.490 264.628
Results
Vcbg [kN] f concrete f Vcbg [kN] Vua [kN]
160.197 0.700 112.138 1.985
6 Warnings
• The anchor design methods in PROFIS Anchor require rigid baseplates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.).
This means load re-distribution on the anchors due to elastic deformations of the baseplate are not considered - the baseplate is assumed to
be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum required
baseplate thickness with FEM to limit the stress of the baseplate based on the assumptions explained above. The proof if the rigid baseplate
assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the existing conditions
and for plausibility!
• Condition A applies when supplementary reinforcement is used. The Φ factor is increased for non-steel Design Strengths except Pullout
Strength and Pryout Strength.
Condition B applies when supplementary reinforcement is not used and for Pullout Strength and Pryout
Strength.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.8.8
Company: PT QUADRAN EMPAT PERSADA Page: 7
Specifier: Project: MINING ESCAVATION
Address: Fastening Point: Combat 42m Medium
Phone I Fax: | Date: 28/05/2022
E-Mail:
7 Installation data
Baseplate, steel: - Anchor type and size: HIT-RE 500 V3 + HAS-U 5.8 M16
Profile: Square hollow, 100 x 100 x 3,6; (L x W x T) = 100 mm x 100 Installation torque: 0.080 kNm
mm x 4 mm
Hole diameter in the fixture: df = 18 mm Hole diameter in the base material: 18 mm
Plate thickness (input): 10 mm Hole depth in the base material: 100 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 136 mm
Drilling method: Hammer drilled
Cleaning: Compressed air cleaning of the drilled hole according to
instructions for use is required
290 290
32
3 4
290
516
x
290
1 2
32
32 516 32
Coordinates Anchor mm
Anchor x y c-x c+x c-y c+y
1 -258 -258 465 - 592 1,108
2 258 -258 981 - 592 1,108
3 -258 258 465 - 1,108 592
4 258 258 981 - 1,108 592
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.html Profis Anchor 2.8.8
Company: PT QUADRAN EMPAT PERSADA Page: 8
Specifier: Project: MINING ESCAVATION
Address: Fastening Point: Combat 42m Medium
Phone I Fax: | Date: 28/05/2022
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan