Professional Documents
Culture Documents
5800 Site Readiness 2G0735
5800 Site Readiness 2G0735
5800 Site Readiness 2G0735
Location
Equipment
Specifications Unpacked Packed
Height 62 cm (24.25 in.)
Width 62 cm (24.25 in.)
Depth 66 cm (26.0 in.) without film trays
?? cm (?? in.) with film trays
Weight 70 kg (155 lbs)
Operating Space The following is the minimum space required around the Imager to perform
Requirements normal operator functions. Service functions will require more space.
134.62 cm
(63.0 in.)
60.96 cm
(24.0 in.)
76.2 cm
(30.0 in.)
Other Location Additional factors that influence where the Imager is located include
Considerations proximity to patients, flammable materials, liquids, and other equipment.
CAUTION:
This equipment is not contained in a sealed cabinet. Do not use this
equipment in locations where it can come in contact with liquids,
including body fluids.
IMPORTANT:
• This equipment is intended to connect to other medical devices. Only
an authorized Service Provider of Carestream Health, Inc. Products or
Customer Qualified Service Personnel may install this equipment.
• Do not locate the Imager within 2 m (6.56 ft) of where a cell phone
will be used, even if the cell phone is separated from the equipment
by a wall.
• Do not locate the Imager within 4 m (13.12 ft) of a microwave oven.
Electromagnetic radiation from a microwave oven is only an issue if,
after the oven door is closed and latched, the seal does not maintain
an electromagnetic tight fit between the oven door and the oven main
housing. Determining if the seal has an electromagnetic tight fit
requires special detection equipment.
• Do not locate the Imager in the presence of flammable anesthetics,
oxygen, or nitrous oxide. The Imager does not have a gas-sealed
electronics enclosure and could ignite any flammable or explosive
gases present in the Imager’s environment.
• Do not locate the Imager in close contact with MRI devices due to
possible high magnetic fields near an MRI unit. The magnetic field in
the area where the Imager is installed must be less than 50 Gauss.
1.83 m (6 ft.)
Environmental Requirements
Temperature • Operating: 15° to 33° C (59° to 91° F)
• Storage: -40° to 60° C (-40° to 140° F)
Altitude • 30 m (100 ft) below sea level to 3,048 m (10,000 ft) above sea level
Surface Condition A level (must be level within 1°) table top or counter capable of supporting
the weight of the Imager. For the Imager to operate with no image
degradation, surface vibration levels cannot exceed the following.
Environmental Effects
• Heat Dissipation: total heat dissipation for the Imager is 850
BTU/hour
• Acoustical Noise:
– Less than or equal to 75 dB-A at 1 m during a sound burst of 1
sec. or less
– Less than or equal to 65 dB-A at 1 m during normal operation
– Less than or equal to 50 dB-A at 1 m during idle mode
Laser Specifications
Item Specification
Wavelength 810 nm
Power 50 mW
Radiation class 3B
Type Diode
Power Requirements
The Imager power supply has an auto-sensing and auto-switching feature for
both voltage and frequency. The current draw is 10 A at 120 V AC, and the
power consumption is a maximum of 1275 W.
One of the following single-phase, 15 A power sources, with grounding,
must be provided within 2.5 m (8 ft) of the Imager.
Area Power
North America 120 V AC +6% to -10%, 60 Hz ±3Hz
Europe 240 V AC ±10%, 50 Hz ±3Hz
Japan 100 V AC ±10%, 50/60 Hz ±3Hz
The wire must be insulation-rated for 600 V. A dedicated line is
recommended.
Network Requirements
Network Connection The 5800 Laser Imager receives digital images from medical imaging
devices (modalities) over a 10/100Base-T Ethernet Network. A single
10/100Base-T Ethernet Network connection via a CAT 5 UTP cable
terminating in an RJ-45 plug must be located less than 9.5 m (31 ft.) from
the bottom rear of the Imager.
Network Information During the installation, you will enter the network information for the
Imager to let it communicate across the network.
Gather and record the information in the following table prior to the
installation of the Imager. Have this page available when you start the
installation. See your site’s network administrator for help to gather the
information.
Required Information for the 5800 Laser ImagerFill in the table:
Host (Computer) Name
IP Address - Use the format: xxx.xxx.xxx.xxx
Subnet Mask - Use the format:
xxx.xxx.xxx.xxx
Default Gateway - Use the format:
xxx.xxx.xxx.xxx
DICOM Port Number - The default port
number, 5040, is correct for most installations.
If necessary you can change it for your site.
You will enter the port number in 2 places: at
the modality and at the Imager.
Modality Prior to installation, you must set up the image source (a modality such as
Configuration CT, MRI, workstation, or other imaging device) to send print jobs to the
5800 Laser Imager. At the modality, the Imager must be added as a print
destination. If you need help adding the Imager, contact the modality’s
vendor.
A list of the modalities that will connect to the Imager and the configuration
for each modality must be available at installation. Use the following to
record the information that will be required.
1 2
Manufacturer: ________________________ ________________________
Model: ________________________ ________________________
Modality Type (CT, DR, MR, etc.): ________________________ ________________________
GSDF Compliant (Yes or No): ________________________ ________________________
If GSDF Compliant, does the modality
send a PLUT with all images (Yes or No): ________________________ ________________________
Film Type: ________________________ ________________________
Film Size: ________________________ ________________________
Modality ID (descriptive name assigned
by the user for use on the Local Panel): ________________________ ________________________
3 4
Manufacturer: ________________________ ________________________
Model: ________________________ ________________________
Modality Type (CT, DR, MR, etc.): ________________________ ________________________
GSDF Compliant (Yes or No): ________________________ ________________________
If GSDF Compliant, does the modality
send a PLUT with all images (Yes or No): ________________________ ________________________
Film Type: ________________________ ________________________
Film Size: ________________________ ________________________
Modality ID (descriptive name assigned
by the user for use on the Local Panel): ________________________ ________________________
5 6
Manufacturer: ________________________ ________________________
Model: ________________________ ________________________
Modality Type (CT, DR, MR, etc.): ________________________ ________________________
GSDF Compliant (Yes or No): ________________________ ________________________
If GSDF Compliant, does the modality
send a PLUT with all images (Yes or No): ________________________ ________________________
Film Type: ________________________ ________________________
Film Size: ________________________ ________________________
Modality ID (descriptive name assigned
by the user for use on the Local Panel): ________________________ ________________________
7 8
Manufacturer: ________________________ ________________________
Model: ________________________ ________________________
Modality Type (CT, DR, MR, etc.): ________________________ ________________________
GSDF Compliant (Yes or No): ________________________ ________________________
If GSDF Compliant, does the modality
send a PLUT with all images (Yes or No): ________________________ ________________________
Film Type: ________________________ ________________________
Film Size: ________________________ ________________________
Modality ID (descriptive name assigned
by the user for use on the Local Panel): ________________________ ________________________
Film
Prior to installation you must order and have on hand Kodak DryView Laser
Imaging Film. Contact your sales representative if you have questions.
Film Types The 5800 Laser Imager accommodates the following film types:
• Kodak DryView DVB Laser Imaging Film
• Kodak DryView DVC Laser Imaging Film
• Kodak DryView DVB+ Laser Imaging Film
• Kodak DryView DVB+ Premium Laser Imaging Film
NOTE: Not all film types are available in every country.
Film Sizes The 5800 Laser Imager accommodates the following film sizes:
• 20 x 25 cm (8 x 10 in.)
• 25 x 30 cm (10 x 12 in.)
• 28 x 35 cm (11 x 14 in.)
• 35 x 35 cm (14 x 14 in.)
• 35 x 43 cm (14 x 17 in.)
Film Storage and Film must be stored at 35° C (95° F) and 85% RH or less. The Imager prints
Throughput up to 80 films per hour.
Seismic Kit
Some installation sites require that the Imager be fastened to the floor to
prevent movement due to earthquake or MR attraction. The brackets and
hardware required to secure the Imager are supplied in a Seismic Kit,
Catalog Number xxxxxx. The Seismic Kit satisfies the requirements of
California Building Code Title 24, Volume 2, Chapter 16A - CCR Uniform
Building Code 2001.