Professional Documents
Culture Documents
DR Fixit Bathseal Waterproofing
DR Fixit Bathseal Waterproofing
WATER PROOFING
T W O - C O M P O N E N T C E M E N T I T I O U S , P O LY M E R M O D I F I E D ,
E L A S T O M E R I C WAT E R P R O O F I N G C O AT I N G
Description
Dr. Fixit Bathseal WPC is a two-component cementitious, polymer modified, elastomeric waterproofing coating
composed of cement, properly selected & graded aggregates, additives & acrylic emulsion polymer as a binder. It
is applied to waterproof and protect concrete and masonry substrates, typically in wet areas such as bathrooms,
kitchen sinks, etc..
Method of Application
1 S U R FAC E P R E PA R AT I O N
}}In sunken portions, which is generally concrete, the areas to be coated with Bathseal WPC, must be mechanically
prepared to remove all lataince & loose particles like cement or mortar deposits, etc.
}}Oil & grease, if any, must be de-greased with suitable solvents & later washed off with a jet of water and must be
brought to a touch dry state.
}}Thereafter, cracks & crevices & gaps between masonry & mortar, if any, must be filled up appropriately with
cement – sand mortar modified with Pidicrete URP.
}}A 50 mm x 50 mm angular fillet must laid at junction of floor-wall in the sunken portion, in cement-sand mortar
admixed with Dr. Fixit Pidicrete URP..
2 MIXING
}}Shake the liquid component well to a homogenous milky colour.
}}Always add powder to polymer under constant stirring using slow speed paddle mixer to achieve smooth and
homogeneous slurry.
}}Allow to stand for about 5 mins to release entrapped air.
}}For new bathrooms.
3 A P P L I C AT I O N O F D R . F I X I T B AT H S E A L W P C
}}Apply first coat of Dr Fixit Bathseal WPC all over the floor surface in bathroom extending on side walls up to 200
to 300 mm height covering the angle fillet.
}}While the coating is still wet place the glass fibre mesh (2.5 mm x 2.5 mm grid) on the angle fillet extending
about 50 mm on floor surface and 50 mm on walls and allow it to soak completely with material.
}}Before the coating dries apply immediately another coat of Dr. Fixit Bathseal WPC only on the angle fillet
completely covering the mesh thus embedding it firmly between two coats of Dr. Fixit Bathseal WPC.
}}Allow the coating to dry completely for 6 to 8 hrs before applying second coat all over the floor area and walls.
}}The angle fillet area now has three coats of Dr. Fixit Bathseal WPC with mesh embedded firmly within the
coating.
}}Allow the coating to dry completely for 3-4 days. Do not cure with water but keep coating moist using wet
hessian cloth.
}}Test the efficacy of the coating by conducting ponding test after complete cure after 3-4 days.
}}For this pond water up to 50-75 mm in sunken portion for 24 hrs and check for effectiveness of waterproofing.
After this lay cement sand screed or brick bat coba, as the case may be, taking care all the time that the coating
140 Dr. Fixit Bathseal WPC
}}
Technical Information
PROPERTIES RESULTS
Coverage
Approximately 0.6 – 0.75 m2 / kg at 1 mm thickness in 2 coats, depending on the level of the substrate.
Packing
10 kg
Pidilite Industries Limited DISCLAIMER The product information & application details given by the company
Construction Chemicals Division & its agents has been provided in good faith & meant to serve only as a general
Ramkrishna Mandir Road, Post Box No. 17411 guideline during usage. Users are advised to carry out tests & take trials to ensure on
the suitability of products meeting their requirement prior to full scale usage of our
Andheri (E) Mumbai 400059 INDIA
products. Since the correct identification of the problems, quality of other materials
Tel +91-22-2835 7000 • Fax +91-22-2835 7008
used and the on-site workmanship are factors beyond our control, there are no
www.doctor-fixit.com • drfixitadvice@pilmail.com expressed or implied guarantee / warranty as to the results obtained. The company
Dr. Fixit Advice Centre (Toll Free No.) 1800-209-5504 does not assume any liability or consequential damage for unsatisfactory results,
arising from the use of our products.
3