Professional Documents
Culture Documents
MJ448 Jig Saw Machine
MJ448 Jig Saw Machine
MJ448 Jig Saw Machine
Instruction Manual
SURFACE
The high-speed wire saw of our factory is assembled by the personnel who have been
engaged in the assembly of this product for more than ten years. Their skills have created
excellent quality. The machine runs in a straight line with low noise and stable operation.
This kind of product has been sold well across the country and is widely favored by users.
This mechanical product is suitable for woodworking and furniture, advertising, footwear,
plastics, hardware and lighting industries, and is a good helper for you to start a business.
Dear user, in order to better master the use and maintenance of this machine, we ask you
As this product may be updated technically, and there may be slight differences between
the actual product and the manual, please refer to the actual product.
GB1255-2000
Catalogue
Before using the product, read the User Manual carefully to check whether the power switch is
damaged due to handling, the thread head is loose, and the brake lever is flexible. If it is not ideal after
Please abide by the mechanical operation procedures and rules, do not operate after drinking, work
with excessive fatigue or taking sleeping pills and other mentally ill persons, and do not work with hand
The motor of the product is 4-pole 0.75KW, 50HZ (unless specially customized by the user, the user can
add under voltage and overload current circuit protection motor devices if necessary.
Do not modify the rotational speed of this product or process products beyond the performance range
For the sake of safety, remember to turn off the power switch and the main power switch after work to
Thank you for your wise choice. In order to enable you to easily operate and use this manual, we
specially compiled it in 2009. I hope it can give you a care and help.
Shunxin brand broaching machine is a full casting machine body, which has beautiful shape, reasonable
structure, and will never change its shape. The saw blade is straight and runs smoothly. The wire saw
blade holder and bearing are specially customized. The accessories are superior, and the price is
moderate. The quality and service of users are very important. It has established a good image among
I hope you can tell us your feelings, thoughts or opinions after use without reservation, and constantly
promote our updated works to make "Shunxin" more perfect. I hope our "Shunxin" people can provide
t/min)
The machine should be placed in a well ventilated place with a flat ground. First
connect the double insulated wire to the button switch, then connect the motor switch (the
knife switch can also be used), close the power switch, remove the right side screen door at
the bottom of the machine, and watch the motor rotate. It is correct if the driving wheel
operation. You can pad thin glue or paper blocks on the base bottom.
After the position is adjusted, please protect the power line with wire tube or wire slot
to prevent the broken circuit caused by the falling of sundries during work.
Before using the machine, drop lubricant on the top of the saw blade holder, and adjust the
tightness of the saw blade and the reverse tension of the pressure spring until the cam at
the front end of the handle makes no noise. When the elasticity is reasonable, the noise can
be eliminated by adjusting the length of the clamping saw blade. The elasticity increases
when the handwheel rotates clockwise, and decreases when the handwheel rotates
clockwise.
When installing the saw blade, the hook teeth shall be downward, and (1-2) teeth of the
three inverted teeth shall be exposed to the table surface for bottom application (when
sawing hard wood, the inverted hook teeth need not be exposed to the table surface).
Supplement: The number of teeth in the saw blade is 1 cm long. Generally, the saw blade
with a higher number of teeth is used for hard materials, and the customer can choose it
With circular saw blade (with teeth around the circumference), the workpiece does not
When sawing the plastic board, when the thickness is large (or the melting point of the
material is low), the water can drip on the sawing side, and the pulling of the surimi is more
smooth.
The small space of the workpiece can be polished by winding the yarn cloth on the saw
blade.
Only when the saw blade is in motion can the workpiece be operated for sawing, especially
when the steering is suspended, the saw blade shall be operated first and the workpiece
When the material is hard, it should be slow when turning the saw to ensure that the upper
and lower dimensions of the workpiece are consistent. At the same time, it should be noted
that when the workpiece is paused and started, the serrated bar clamped in the material
will be taken away from the workbench due to the workpiece clamping the saw blade when
turning. When the workpiece is pulled down again, the workpiece can snap the finger, so
When sawing small craft, it is required to use a small saw blade, at the same time, use wood
or plastic to plug the face sawtooth hole and drill a small hole. (approx. 10 mm diameter)
When a new saw blade is installed and used, as usual, it is found that the thrust is not
consistent with the direction of the saw path (running sideways). It may be that the size of
the two sides of the new saw blade is different or one side is sharp and the other side is
blunt. A new saw blade should be replaced for better work. The thickness and density of the
saw material with reasonable saw blade tension can make the internal bearing of the
5、 Maintenance instructions
1. Do not give the machine to personnel without mechanical maintenance experience for
2. Remember to drop lubricating oil once when going to work at the movable place of saw
blade holder.
3. When the mechanical noise is found to be excessive, check whether the fasteners are
loose and whether the bearing is worn beyond the usable range. If the noise is found to
come from the gap between the worn bearings, replace the bearings in time.
4. When replacing the bearing, follow the steps below:
A. Turn off the power, put the back of the machine down, blow out the dust with the dust
B. Rotate anticlockwise to loosen the M12 linkage bolt between the connecting rod and the
eccentric wheel, and then gradually unscrew the bolts of each component, and make a
record. The number of shims between the two connecting rods and the bearing, the
direction of the two saw arms and the I-shaped fork frame shall be marked by comparison,
and they shall not be replaced up and down, so that they will have the same effect as the
C. The four linkage bearing pedestals can be interchanged, and the lower saw arm support
D. If the cam (at the front end of the handle, the lower end and the M8 bolt interface of the
saw blade are seriously worn, and the tension of the saw blade is insufficient, repair
welding is required. The arc degree is R=38 -: the M8 bolt at the lower end of the wheel is
worn, remove the compression spring and the screw at its center, and lower the anti
E. When it is difficult to take out 2 sets of bearings of the main shaft; The size of the stopper
can be used to plug the shaft inner sleeve or outer sleeve for spot welding, and then knock
it out.
F. When reassembling the machine, tighten each nut, especially the linkage M12 bolt
between the connecting rod and the eccentric, and put the bolt into the spring washer first
and then into the inner sleeve of the bearing ---- the inner tooth hole of the eccentric wheel.
G. After reassembly, power on and test the machine. If there is no abnormality, erect the
machine and install the clamping seat, and use a ruler or right angle triangle to calibrate the
plane perpendicularity.
H. After one and a half years, lithium base lubricant shall be added to the bearing of the
motor to fill the space of the bearing room. The motor shall be kept ventilated for heat
dissipation.
5. When the machine is not used for a long time, the table top shall be coated with
6. The bearing shall not be dripped with lubricating oil to prevent the diluted lithium oil
from flowing out and accelerating the service life of the bearing.
7. The bearings used for this machine are dust-proof rubber sealed bearings with good
material hardness, including 10 sets of 6200, 4 sets of 6000, 1 set of 6300 and 6301
respectively, and 2 sets of 6205. (Before 2014, the old model was used to repair parameter
bearings)
8. After the improvement in the transition period, each assembled bearing is 6200 8 sets,
. 2 Both the bearing and saw blade clamp are wearing parts. Please contact the seller when
The power of the small power motor (also known as fractional horsepower motor) that is
conventionally assembled for this product is 0.75kw. Users have new demands, and can
install 0.55kw, 1.1kw, 0.55kw, 0.75kw and 1.1kw for a single camera. The speed can be
accelerated or slowed down. Please consult the dealer for details.
8、 Warm service
This product is a low failure machine. We start to trade in the old for the new, collect the
same kind of old products, repair and improve the same kind of products. Customers only
need to entrust the freight company to collect money on behalf of them, so that we can
After the machine purchased by the user at the dealer is loaded into the vehicle, the user
should use bandages to tighten the body, without fixing the upper and lower arms or
deforming or shifting. If the machine feet are uneven, paper or wood should be padded first.
If there is no forklift, the machine body can be leveled, and the machine can be moved
down or lifted by means of battens or ropes. Pay attention to safety, and let the machinery
One manual