Professional Documents
Culture Documents
ASS2008000401 (C) Roxtec EzEntry Installation Instruction EN For Web Use
ASS2008000401 (C) Roxtec EzEntry Installation Instruction EN For Web Use
Installation instructions
Roxtec EzEntry kits
TM
Components
ec.com
www.roxt
53 Ø3.6 (4x)*
53
37
Ø51 R1 max (4x)
42
53
53
108
37
Ø3.6 (4x)* Ø3.6 (4x)* 130
32
Roxtec EzEntryTM 10 fits the standard
multipin connector knock-out.
EzEntry™ 16 EzEntry™ 24
Ø7.4 (4x)*
4 123.5 123.5
Ø7.4 (6x)*
R2 max (4x)
62
62
37
R2 max (8x)
12.5
12.5
193 255
EzEntry™ 32
Ø7.4 (8x)*
R2 max (8x)
62
37
158 158
12.5
335
1 2 3 4
Insert the frame into the opening. Attach the frame firmly. For EzEntry™ 16, use the Lubricate the inside surfaces of
counter flange (article no. the frame with Roxtec Lubricant.
2CV0000000016) if the thickness Make sure to lubricate the
of the structure is 2 mm or less. corners.
5 6 7 8
A
Feed the cables through the Achieve a gap of 0.1-1.0 mm (A) Adapt the module to the cable The number of layers may not
frame opening. between the module halves by size. Peel off layers until you differ (A) by more than one
peeling off layers. achieve the gap seen in previous between the corresponding
step. module halves.
9 10 11 12
Lubricate all sealing surfaces of Insert the modules according to To simplify the installation, use To simplify the insertion of the
the modules thoroughly. the packing plan. a Roxtec pre-compression tool last module, angle the module
(not included). halves and press them into the
frame simultaneously.
13 14 Torque settings
Frame type Rec. torque* * The recommended torque
(Nm) depends on several things, e.g
cable or pipe size, amount of
4 mini 3-5 used lubricant, material in the
4 3-5 cable sheath, etc.
10 5-7
16 5-7
24 5-7
32 5-7
Tighten the screw of the Excess lubricant is a sign of good
integrated compression unit to compression.
the specified recommended
torque.
Roxtec EzEntry™ 4 mini installation
m
ec.co
roxt
www.
TM
Achieve a gap of 0.1-1.0 mm (A) Adapt the module to the cable Lubricate the inside of the frame Feed the cables through the
between the module halves by size. The halves may not differ by and the modules with Roxtec frame.
peeling off layers. more than one layer. Assembly Gel.
5 6 7
Insert all modules from the back Attach the frame to the structure. Excess lubricant is a sign of good
of the frame and install all cables Tighten the screws alternately compression.
before attaching the frame to the and in small steps to full stop.
structure.
Disassembly
1 2
Roxtec ® and Multidiameter ® are registered trademarks of Roxtec in Sweden and/or other countries.
Untighten the screw of the Remove the modules needed.
integrated compression unit.
Note
OO For optimum reliability, wait 24 hours or longer after installation before exposing the cables or pipes to strain or pressure.
OO Approvals or certificates may include amendments or limitations related to this application.
OO The latest version of this and related documents are found at roxtec.com.
DISCLAIMER
”The Roxtec cable entry sealing system (”the Roxtec system”) is a modular- The product information provided by Roxtec does not release the purchaser
based system of sealing products consisting of different components. Each of the Roxtec system, or part thereof, from the obligation to independently
and every one of the components is necessary for the best performance determine the suitability of the products for the intended process, instal-
of the Roxtec system. The Roxtec system has been certified to resist a lation and/or use.
number of different hazards. Any such certification, and the ability of the Roxtec gives no guarantee for the Roxtec system or any part thereof and
Roxtec system to resist such hazards, is dependent on all components assumes no liability for any loss or damage whatsoever, whether direct,
that are installed as a part of the Roxtec system. Thus, the certification indirect, consequential, loss of profit or otherwise, occurred or caused by the
is not valid and does not apply unless all components installed as part Roxtec systems or installations containing components not manufactured
of the Roxtec system are manufactured by or under license from Roxtec by an authorized manufacturer and/or occurred or caused by the use of
(“authorized manufacturer”). Roxtec gives no performance guarantee with the Roxtec system in a manner or for an application other than for which
respect to the Roxtec system, unless (I) all components installed as part of the Roxtec system was designed or intended.
the Roxtec system are manufactured by an authorized manufacturer and Roxtec expressly excludes any implied warranties of merchantability and
(II) the purchaser is in compliance with (a), and (b), below. fitness for a particular purpose and all other express or implied representa- Roxtec International AB
(a) During storage, the Roxtec system or part thereof, shall be kept indoors tions and warranties provided by statute or common law. User determines
in its original packaging at room temperature. suitability of the Roxtec system for intended use and assumes all risk and
Box 540, 371 23 Karlskrona, SWEDEN
(b) Installation shall be carried out in accordance with Roxtec installation liability in connection therewith. In no event shall Roxtec be liable for indirect, PHONE +46 455 36 67 00, FAX +46 455 820 12
instructions in effect from time to time. consequential, punitive, special, exemplary or incidental damages or losses.”
EMAIL info@roxtec.com, www.roxtec.com