Professional Documents
Culture Documents
NXZMZ
NXZMZ
04
NXZM、NXZ(H)M
Automatic Transfer Switch
User Instructions
3 You are prohibited from touching the conductive part when the product is
operating.
4 Do not install the product at places where gas medium can cause metal
corrosion and insulatin damage.
5 After installing the product, finishing the inspection of load side line and
splitting the fire-resistance circuit, the controller must be set to “Manual”
position and the product must be set to split position. Switch the controller
to “Auto” position after line fault is eliminated.
1 Applicatin Information
a) The normal application temperature of the product is -5℃~+40℃;
Note: If you need to use the product under -25℃~+70℃, please consult the manufacturer.
b) If you need to use the product above 2000m altitude, please consult the manufacturer;
c) Pollution class: class 3;
d) Installation category of main circuit: Ⅲ;
e) Enclosure protection class: IP20.
Tools required
1.Determine
Phillips screwdriver
product
technical
Word screwdriver
parameters.
Allen wrench 2.Type AT and
BT controllers
Hex wrench
have the
function of
communication.
Fig 1 Inspection
3P 2X4
Flash barrier
4P 2X6
Type A 5
wiring
terminal
of Type AT
6
external Type B
signal
(controller)
Type BT 7
01
NXZM、NXZ(H)M Automatic Transfer Switch
Manual test
Power-on test
Turn the toggle switch to Automatic mode Manual mode Setting mode
the Automatic position
Stop mode Generator activation Failure alarm Automatic transfer Automatic transfer
(absent for PC class) Operating transfer Return transfer
delay time delay time
Fig 3 Power-on test
02
NXZM、NXZ(H)M Automatic Transfer Switch
Hmax
A
C H1
L G H2
B2
B1
D
B
H H1 H2
Product model A B B1 B2 C D G L M N
S H S H S H
NXZM-63、125
300 240 230 223 267 220 25 178 178 190 151 161 47 56 9 17
NXZHM-63、125
NXZM-160
340 250 245 240 307 230 30 194 167 195 152 180 50 9 17
NXZHM-160
NXZM-250
390 250 367 240 357 230 35 225 181 216 155 190 49 50 9 17
NXZHM-250
NXZM-400、630
535 334 464 342 475 304 44 304 234 198 66 11 26
NXZHM-400、630
NXZM-800
660 344 477 344 600 314 58 385 238 203 68 11 26
NXZHM-800
03
NXZM、NXZ(H)M Automatic Transfer Switch
Unit: mm
64 17 4.5 60
105
101
60≤a≤62
101≤b≤103
Thickness≤2.5
NXZM/NXZHM-63
8.0 17.5 6.5 4 N·m
NXZM/NXZHM-125
NXZM/NXZHM-400
10.5 30.5 11.5 30 N·m
NXZM/NXZHM-630
NXZM/NXZHM-800 15 43 14 40 N·m
04
NXZM、NXZ(H)M Automatic Transfer Switch
1. Main power
supply and
voltage signal
Load bus-bar 4P
sampling line
phase
3P Product wiring diagram sequence must
be consistent.
Normal power Alternative power
Normal Alternative 2. During
bus-bar bus-bar
power power wiring, the
Wiring terminal of
neutral line voltage signal
sampling line in
order as shown.
Wrong wiring
may lead to
burn down of
the controller.
3P
Load bus-bar
05
NXZM、NXZ(H)M Automatic Transfer Switch
neutrul line
neutral line
Alternative
Connect to the external
Normal
terminal of controller
directly.
Any forms of electrical
connection of these terminals is
strictly forbidden.
Common Common
201 202
1. Any type of
Note: Please tear off the sticker before use electrical
and keep it for future use. connection
between
terminal 201
and teminal
It is used under the 202 is
Grid-power generator
Note:
prohibited,
mode and may be omitted,
but the delay of generator
Do not connect Active output otherwise the
201 and 202. AC230V/0.5A
start-up default to 0s. controller will
be burnt!
2. Terminal 501
and 502 of
controller can
only be
Commom connectd with
passive closing
signal to
achieve fire
cintrol linkage.
If they are
directly
connected to
any active
signal, the
To the remote power
terminal 601 land 603 are Terminals 503 and 504 are
connected. connected after the off of fire 3. Strip at least
control. After the fire control
Note: signal bering removed, for the
8mm of the
1: Dotted line is the internal structure of the controller. ATSE switch to“Manual”and insulation of
then press Confirm/Return in
2: Type A controller doesn’t have functions of generator control the wire before
automatic mode, or press
(601 602 603) and feedback output of fire protection control (503, 504). Comfirm/Return directly in inserting it into
3: Type AT and BT controllers have the function of communication.
manual mode. the terminal.
Fig 8 Signal and control terminal wiring diagram
06
NXZM、NXZ(H)M Automatic Transfer Switch
5 Controller setup
Instructions of controller operation interface
07
NXZM、NXZ(H)M Automatic Transfer Switch
08
NXZM、NXZ(H)M Automatic Transfer Switch
09
NXZM、NXZ(H)M Automatic Transfer Switch
Normal operation of
Normal operation of normal power supply
normal power supply
Failure of normal
Failure of normal power supply T3
power supply T1
Start-up of generator
Disconnection of
normal power supply
Generator output reaches
set value T1
Power up of alternative
power supply
Disconnection of
normal power supply
Connection of alternative
power supply
Power up of alternative
power supply
Recovery of normal
power supply T2
Connection of alternative
Disconnection of power supply
alternative power supply
Recovery of normal
Power up of normal power supply T2
power supply
Disconnection of
Connection of normal alternative power supply
power supply
Power up of normal
power supply
Connection of normal
Flow Chart of Automatic Charge and Automatic power supply
Generator shutdown
Normal operation of
normal power supply
Flow Chart of Automatic Charge and Automatic Recovery
Failure of normal
power supply T1 (Grid - Power Generation) of Controller
Disconnection of
normal power supply I: Normal power supply
Power up of alternative
power supply
II: Alternative power supply
T1: Switching delay time
Connection of alternative
power supply
Failure of normal power supply, time before
Recovery of normal
power supply
disconnection of I
T2: Return delay time
Power supply of
alternative power source
Recovery of normal power supply, time
Failure of alternative
before disconnection of II
power supply T2
Disconnection of
T3: Generator start-up delay time: 0s~180s
alternative power supply adjustable
Power up of normal
power supply T4: Generator shutdown delay time: 0s~180s
adjustable
Connection of normal
power supply
10
NXZM、NXZ(H)M Automatic Transfer Switch
6 Product troubleshooting
Table 5 Non-common fault and solution
The product is not connected to neutral Make sure the incoming line terminal is
The display interface of controller is phase, especially for a 3P product. firmly connected and in good contact.
not on after powering up
Controller fuse is blown. Replace the fuse.
11
NXZM、NXZ(H)M Automatic Transfer Switch
7 Environmental Protection
In order to protect the environment, the product or product parts should be disposed of according to
the industrial waste treatment process, or be sent to the recycling station for assortment, dismantling and
recycling according to local regulations.
12
NXZM、NXZ(H)M Automatic Transfer Switch
QC PASS
NXZM、NXZ(H)M
Automatic Transfer Switch
IEC/EN 60947-6-1
PD1 Check 15
13
NXZM、NXZ(H)M
Automatic Transfer Switch
User Instruction