Professional Documents
Culture Documents
Variation
Variation
CIVIL WORK
(i) Cleaning jungle including up rooting of rank, vegetations grass,
push, wood trees and amplings of grith upto 30 cms. measured at
1 a height of 1 M. above ground level and removal of rubbish up Sqm 10512.44 3.20 33639.81 10859.55 3.20 34750.56
to a distance of 50M. out side the periphery of area cleared.
3 CARTED EARTH (UPTO 10 KM) Cu.M 1864.86 219.65 409615.98 1899.44 219.65 417211.48
d Shelves (Cast in situ) Sqm 58.92 693.05 40834.51 58.92 693.05 40834.51
Lintels, beams, plinth beams, girders, bressumers and cantilevers
e Sqm 19886.58 552.05 10978387.13 20378.77 552.05 11250100.62
f Columns, Pillars, Piers, Abutments, Posts and Struts Sqm 8884.11 733.70 6518269.31 9098.81 733.70 6675794.70
Weather shade, Chajjas, corbels etc., including edges Sqm
g Stairs, (excluding landings) except spiral-staircases Sqm 397.78 622.35 247558.38 418.97 622.35 260745.98
Small lintels not exceeding 1.5 m clear span, moulding as in
h cornices, window sills, string courses, bands, copings, bed plates, Sqm 850.56 284.85 242280.73 850.56 284.85 242280.73
anchor blocks and the like
i Edges of slabs and breaks in floors and walls
Under 20 cm wide mtr 1151.80 173.25 199549.35 1151.80 173.25 199549.35
j Weather shade, Chajjas, corbels etc., including edges Sqm 885.00 766.75 678573.75 901.79 766.75 691447.48
Extra for shuttering in circular work (20% of respective centering
K and shuttering items) 249.25 342.64 85403.02 318.86 342.64 109254.19
a All works up to plinth level Cum 4830.74 8398.65 40571692.40 4936.86 8398.65 41462957.14
b All works above plinth level up to floor V level Cum 5764.36 9802.20 56503379.86 5921.53 9802.20 58043991.63
Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each
6 Cum 280.95 0.00 280.95 0.00
four floors or part thereof.
Wall Joint of 100 mm gap M 457.20 4658.30 2129774.76 457.20 4658.30 2129774.76
Roof Joint of 100 mm gap M 91.00 5193.45 472603.95 91.00 5193.45 472603.95
First class bricks work in 1:6 in cement and fine sand of 1.25 cf
mortar in foundation and plinth including supply of all materials,
1 Cum 471.97 3900.00 1840682.81 483.71 3900.00 1886468.81
labor and T&P etc. required for completion of the work.
Cement mortar 1:6 (1 cement : 6 Coarse sand) Cum 6687.44 7280.70 48689228.73 6852.08 7280.70 49887923.18
Extra for brick work / AAC block masonry / Tile brick masonry in
3 superstructure above floor V level, for each four floors or part Cum 0.00 236.65 0.00 0.00 236.65 0.00
thereof by mechanical means.
Frame size 65 x 150 mm mtr 4031.85 1543.80 6224370.03 4031.85 1543.80 6224370.03
Melamine polishing on wood work (one or more coat). sqm 78.20 110.75 8660.87 78.20 110.75 8660.87
Supply & fixing of 4.5 Cm. thick teak wood part panelled and part
glazed door and window shutter including supply & fixing of
wooden cleats and stops and including fixing & adjustment of
hinges, bolts, locks, handles spring and or other fittings but
excluding their supply and including painting with two coats of
black Japan on all iron fitting if necessary. Including fixing the
glass panes with putty for bradglass and glass to be 4 mm. thick.
Fitting with necessary screws to be supplied by the deptt.(For
Main Entrance door)
As in item no. 409 above but fully panelled. 59.46 4550.00 270543.00 59.46 4550.00 270543.00
3 (D) For double leaf shutters add extra in over all rates sqm 478.90 200.00 95779.00 478.90 200.00 95779.00
Extra for providing vision panel not exceeding 0.1 sqm in all type
4 of flush doors (cost of glass excluded) (overall area of door shutter
to be measured):
Rectangular or square Sqm 712.21 173.95 123889.36 712.21 173.95 123889.36
Extra for providing lipping with 2nd class teak wood battens 25
5 mm minimum depth on all edges of flush door shutters (over all 509.22 401.40 204398.90 533.67 401.40 214213.13
area of door shutter to be measured).
7
Providing and fixing M.S. grills of required pattern in frames of
windows etc. with M.S. flats,square or round bars etc. including
priming coat with approved steel primer all complete.
Fixed to steel windows by welding KG 41470.17 165.3 6855019.10 41470.17 165.30 6855019.10
8
Providing and fixing aluminium extruded section body tubular type
universal hydraulic door closer (having brand logo with ISI, IS :
each 1483.00 851.60 1262922.80 1483.00 851.60 1262922.80
3564, embossed on the body, door weight upto 36 kg to 80 kg and
door width from 701 mm to 1000 mm) with double speed
adjustment with necessary accessories and screws etc. complete.
15 Providing and fixing fly proof stainless steel grade 304 wire gauge,
to windows and clerestory windows using wire gauge with average
width of aperture 1.4 mm in both directions with wire of dia. 0.50
mm all complete.
With 12 mm mild steel U beading. Sqm 1786.34 1001.50 1789014.50 1786.34 1001.50 1789014.50
Providing and fixing 2nd class teak wood lipping/ moulded beading
or taj beading of size 18X5 mm fixed with wooden adhesive of
16 approved quality and screws/ nails on the edges of the Pre- MTR. 1976.40 78.85 155839.14 1976.40 78.85 155839.14
laminated particle board as per direction of Engineer-in-charge.
Providing and fixing panic bar / latch (Double point) fitted with a
single body, Trim Latch & Lock on back side of the Panic Latch of
20 each 88.00 7134.85 627866.80 88.00 7134.85 627866.80
reputed brand and manufacture to be approved by the Engineer-
in- charge, all complete.
Two track two panels sliding door made of (big series) frame
67 x 50 mm & sash 46 x 82 mm both having wall thickness
SQM 152.21 6005.00 914021.05 152.21 6005.00 914021.05
of 2.3 ± 0.2 mm and single glazing bead / double glazing
bead of appropriate dimension.
Extra for providing opening of required size & shape for wash
basin/ kitchen sink in kitchen platform, vanity counter and similar
4 location in marble/ Granite/ stone work, including necessary holes Each 179.00 734.55 131484.45 179.00 734.55 131484.45
for pillar taps etc. including moulding, rubbing and polishing of cut
edges etc. complete.
INSTALLATION:
3/4/5 nos. of wall panel Impalers of shall be fixed to the wall
surface using self-tapping screws. Silica based construction
adhesive to be dabbed on to the projecting elements (spikes) of
the impalers. of Optra wall panels shall be pierced through the
spikes of the impalers ensuring the line and level of the panels are
maintained.
Installation to be carried out by of Trained Installation team &
Installation should be carried out as per of recommended
procedure.
Polished Granite stone slab jet Black, Cherry Red, Elite Brown,
Sqm 6546.52 3526.60 23086955.10 6546.52 3526.60 23086955.10
Cat Eye or equivalent.
Polished Granite stone slab jet Black, Cherry Red, Elite Brown,
Sqm 64.35 2476.45 159359.56 64.35 2476.45 159359.56
Cat Eye or equivalent.
Providing and fixing Ist quality ceramic glazed wall tiles conforming
to
IS: 15622 (thickness to be specified by the manufacturer), of
approved
make, in all colours, shades except burgundy, bottle green, black
of
any size as approved by Engineer-in-Charge, in skirting, risers of
steps Sqm 1472.16 1030.30 1516766.45 1472.16 1030.30 1516766.45
and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement :
3
coarse sand) and jointing with grey cement slurry @ 3.3kg per
sqm,
including pointing in white cement mixed with pigment of
matching shade
complete.
Providing and fixing 1st quality ceramic glazed floor tiles
conforming to
IS : 15622 (thickness to be specified by the manufacturer ) of
approved
make in all colours, shades except burgundy, bottle green, black of
any
size as approved by Engineer-in-Charge in skirting, risers of steps Sqm 1736.60 927.90 1611386.50 1736.60 927.90 1611386.50
and
dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3
coarse
sand) and jointing with grey cement slurry @ 3.3kg per sqm
including
pointing in white cement mixed with pigment of matching shade
complete.
Supply and fixing 6 mm. (¼") China white glazed tiles in flooring or
in skirting or dado laid with 1:3 Cement and approved coarse sand
9 mortar finished with white cement slurry, jointing and polishing 1919.80 900.00 1727822.70 1944.77 900.00 1727822.70
complete, including supply of all materials, labour and Tools and
Plants.
Supply and fixing of Kota stone in floor ing 20 mm thick and joint
filled with 1:2 cement and coarse sand with approved colouring
materials to be given an even shade with 12 mm base coat
(bedding) of 1:2 cement & coarse sand morter and polished by
10 Sqm 2395.82 900.00 2156238.00 2531.81 900.00 2278629.00
hand or machine and finally finished with french manson polish or
other approved polish including supply of all materials, labour,
Tools & plants etc. required for proper completion of the work.
Supply and fixing 6 mm. (¼") China white glazed tiles in flooring or
in skirting or dado laid with 1:3 Cement and approved coarse sand
12 mortar finished with white cement slurry, jointing and polishing 1272.43 900.00 1145187.90 1372.82 900.00 1235538.90
complete, including supply of all materials, labour and Tools and
Plants.
Size of Tile 600x600 mm Sqm 2544.26 1500.55 3817791.22 2544.26 1500.55 3817791.22
Size of Tile 800x800 mm Sqm 4456.29 1758.70 7837277.22 4456.29 1758.70 7837277.22
Providing and laying Vitrified tiles in different sizes (thickness to
be specified by manufacturer), with water absorption less than
0.08 % and conforming to I.S. 15622, of approved make, in all
colours & shade, in skirting, riser of steps, over 12 mm thick bed
Sqm 333.86 1758.70 587159.58 333.86 1758.70 587159.58
of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey
cement slurry @ 3.3kg/sqm including grouting the joint with white
cement & matching pigments etc. complete.
2.5 cm (1") thick 1:2:4 plain cement concrete floor with cement,
approved coarse sand and 2 cm. (1") graded approved stone grit,
laid in panels finished with 3 mm. (1/8") floating coat of neat
cement of cement and marble dust in ratio 5:1 as specified over
and including 8 cm (3") thick base concrete consisting of cement,
fine sand of 1.25 fineness modulus and brick ballast 4 cm. (1½") 152.06 50.00 7603.13 152.06 50.00 7603.13
gauge in the proportion of 1:4:8 and removing any overlapping
mortar at the joints of the penals if any and giving them a uniform
finish, including supply of all materials, labour, Tools & plants etc.
required for proper completion of the work.
In 75x75 mm deep chase mtr 1161.93 237.25 275667.89 1204.39 237.25 285741.53
1:6 (1 cement: 6 fine sand) Sqm 28196.54 303.90 8568927.90 28723.27 303.90 8729001.15
One or more coats on old work Sqm 53841.10 84.65 4557648.77 55425.46 84.65 4691764.85
6 Graniza (Natural Finish- 5 Shades) Sqm 3246.01 1399.45 4542621.70 3310.19 1399.45 4632438.40
With float glass panes of 5.50 mm thickness Sqm 4474.63 1296.40 5800907.09 4525.22 1296.40 5866491.97
Up to 5mm depth and 5 mm width M 1188.60 79.45 94434.27 1188.60 79.45 94434.27
Providing and laying "brick coba" 12mm thick laid with M-150
class brick bat coba 7.50 cm thick with gap of 15mm to each
other, over 20mm thick base of cement mortar 1:4 cement and
coarse sand mixed with water proofing compound spreading
cement slurry mixed with aerelic cement concrete water proofing
compound filled gaps of coba & top of coba mortar mixed with
water proofing compound in 1:4 cement and coarse sand mortar
finished smooth & top mashed false square 30cm x cm and side 7551.55 910.00 6871909.59 7884.19 910.00 7174611.99
wall parapet shall be mono tythic plaster wall upto 30 cm higher
and junction and corner shall be rounded by brick ballast cement
and coarse sand masonary Coba with top finished plaster mixed
with acetic water proofing compound @ 2% by weight & including
S/o all material, labour, T&P etc complete for proper completion of
work.
Supplying and Stacking Filling sunken floor with over burnt jhama
brick aggregate 120mm to 40mm including compacting of
7 Cum 158.60 819.85 130030.26 158.60 819.85 130030.26
materials complete as specified and directed for all levels.
Extra for openable side / top hung vision glass panels (IGUs)
including providing and supplying at site all accessories and
hardwares for the openable panels as specified and of the
approved make such as heavy duty stainless steel friction hinges,
min 4 -point cremone locking sets with stainless steel plates,
4 Sqm 131.62 3163.10 416324.06 131.62 3163.10 416324.06
handles, buffers etc. including necessary stainless steel screws/
fasteners, nuts, bolts, washers etc. all complete as per the
Architectural drawings, as per the approved shop drawings, as
specified and as directed by the Engineering- Charge.
Providing and fixing dry cladding upto 10 metre heights with
30mm thick
gang saw cut stone with (machine cut edges) of uniform colour
and
size upto 1mx1m, fixed to structural steel frame work and/ or with
the
5 help of cramps, pins etc. and sealing the joints with approved Sqm 471.55 2407.40 1135197.43 603.23 2407.40 1452203.87
weather
sealant as per Architectural drawing and direction of Engineer-in-
charge.
(The steel frame work, stainless steel cramps and pins etc. shall
be
paid for separately)
White sand stone - 30mm thick gang saw cut stone
TOTAL 134573035.97 368715452.14 7705685.03 TOTAL 139069238.62 376174642.77 7795501.73 COST INCREASE IS
Less 14.05 % GST on DSR Item 323292812.05 329833093.18 DUE TO THE INCREASE
Less 1 % Labour Cess on DSR Item 320091893.12 326567418.99 IN AREA DUE TO
TOTAL 134573035.97 320091893.12 7705685.03 TOTAL 139069238.62 326567418.99 7795501.73 MERGER OF LIBRARY &
TOTAL COST OF CIVIL WORK 462370614.11 473432159.34 11061545.23 ADMIN BLOCK
B INTERNAL PLUMBING
1.0 Sanitary Fixtures & CP Brass Fittings
Providing and fixing vitreous china water closet squatting pan (Indian
1.1
type).
1.1.1 Orissa pattern W.C. pan size 580x440 mm Each 3 1820.00 5460.00 3 1820 5460
Providing and fixing P.V.C. low level flushing cistern with manually
1.2 controlled device (handle lever) conforming to IS 7231, with all fittings Each 3 1130.00 3390.00 3 1130 3390
and fixtures complete. 10 litre capacity – white
Providing and fixing vitreous china dual purpose closet suitable for use
as squatting pan or European type water closet (Anglo Indian W.C. pan)
with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre
low level flushing cistern with fitting and brackets, 40 mm flush bend, 20
1.3
mm over flow pipe, with specials of standard make and mosquito proof
coupling of approved municipal design complete, including painting of
fittings and brackets, cutting and making good the walls and floors
wherever required.
White vitreous china dual purpose W.C. pan with white solid plastic seat
1.3.1 and lid with white vitreous china flushing cistern and C.P. flush bend ISI Each 8500.00 0.00 0 8500 0
Mark Kajaria equivalent Indian made Brand.
Providing and fixing white vitreous china extended wall mounting water
closet of size 780x370x690 mm of approved shape including providing
& fixing white vitreous china cistern with dual flush fitting, of flushing
1.4 Each 246 10800.00 2656800.00 246 10800 2656800
capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat
cover, and cistern fittings, nuts, bolts and gasket etc
complete. ISI Mark Kajaria eqvilent Indian made Brand.
Providing and fixing 8 mm dia C.P./ S.S. Jet with flexible tube upto 1
1.5 metre long with S.S. triangular plate to European type W.C. of quality Each 515.00 0.00 515 0
and make as approved by Engineer–in-charge
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass
pillar taps, 32 mm C.P. brass waste of standard pattern, including
1.6
painting of fittings and brackets, cutting and making good the walls
wherever require:
Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass
single hole basin mixer of approved quality and make, including painting
1.7
of fittings and brackets, cutting and making good the walls wherever
required:-
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per
IS 13983 with C.I. brackets and stainless steel plug 40 mm including
1.8
painting of fittings and brackets, cutting and making good the walls
wherever required :
1.8.1 Kitchen sink with drain board 510x1040 mm bowl depth 200 mm Each 29 3930.00 113970.00 29.00 3930.00 113970
Providing and fixing white vitreous china laboratory sink with C.I.
brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and
1.9 40mm C.P. brass trap with necessary C.P. brass unions complete,
including painting of fittings and brackets, cutting and making good the
wall wherever required :
Providing and fixing P.V.C. Waste pipe for sink or wash basin
1.11
including P.V.C. waste fittings complete.
1.11.1 Semi rigid pipe, 40 mm dia. Each 29 105.00 3045.00 29 105 3045
Providing and fixing CP Brass 32mm size Bottle Trap of approved
1.12 Each 256 883.05 226060.80 256.00 883.05 226060.8
quality & make and as per the direction of Engineer-in-charge.
Providing and fixing toilet paper holder standrad size ISI marked C.P.
1.14 Each 246 220.00 54120.00 246 220 54120
brass as per direction Engineer-in-charge
Providing and fixing white vitreous china battery based infrared sensor
operated urinal of approx. size 610 x 390 x 370 mm having pre & post
1.15 flushing with water (250 ml & 500 ml consumption), having water inlet Each 72 6913.90 497800.80 72.00 6913.90 497800.8
from back side, including fixing to wall with suitable brackets all as per
manufacturers specification and direction of Engineer-in-charge.
1.16.1 15 mm nominal bore Each 249 525.00 130725.00 249 525 130725
Providing and fixing C.P. brass long nose bib cock of approved quality
1.17
confirming to ISI standards and weighing not less than 810 gms.
Providing and fixing C.P. brass angle valve for basin mixer and geyser
1.18
points of approved quality confirming to IS:8931
1.18.1 15 mm nominal bore Each 982 485.00 476270.00 982 485 476270
1.19 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
Providing and fixing uplasticised PVC connection pipe with brass unions
1.21 :
1.21.1 45 cm length, 15 mm nominal bore Each 982 83.00 81506.00 982 83 81506
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm
high and 112 mm distance from wall of standard shape with bracket of
1.22 the same materials with snap fittings of approved quality and colour, Each 260 158.55 41223.00 260 158.55 41223
weighing not less than 105 gms.
Providing and fixing PTMT towel rail complete with brackets fixed to
wooden cleats with CP brass screws with concealed fittings arrangement
1.23
of approved quality and colour.
600 mm long towel rail with total length of 645 mm, width 78 mm and
1.23.1 Each 82 595.50 48831.00 82 595.5 48831
effective height of 88 mm, weighing not less than 190 gms.
Providing and fixing PTMT soap Dish Holder having length of 138mm,
breadth 102mm, height of 75mm with concealed fitting arrangements,
1.24 Each 82 130.50 10701.00 82 130.5 10701
weighing not less than 106 gms.
Providing and fixing health faucet with 1 m long flexible tube and wall
1.25 hook including all fittings Jaguar Cat. No. ALD-IVC-593 or approved Each 246 919.00 226074.00 246.00 919.00 226074
equivalent.
Providing and fixing 15mm C.P brass Sink Mixer Jaguar Model. No.
FLR-5165 or approved equivalent.) for kitchen sink with swinging spout
1.26 Each 29 3130.00 90770.00 29.00 3130.00 90770
complete. Including cutting and making good the walls wherever
required .
Providing & fixing SS Grab Bar Euronics Model No. EGR (S02) & SS
1.27 Grab Rail Euronics Model No. EGR 01 or approved equivalent,Including Each 8 8337.00 66696.00 8.00 8337.00 66696
cutting and making good the walls wherever required.
Providing and fixing vertical storage type hot water heater fixed to wall
with anchor bolts & nuts, 15mm CP brass angle stop cock and 15mm CP
1.28 brass non-return valve complete including making connections with
15mm dia CP connecting pipes on inlet and outlet, suitable length of
power cable and 15 amps plug.
1.28.1 Capacity 25 Litres Venus Model Magma 25GV Each 27 9446.00 255042.00 27.00 9446.00 255042
Providing and fixing 150 litre/ hr. cooling and storage capacity,fully
stainless steel electric storage type water cooler (Blue Star model No.
1.29 SDLX 15150 or equvalant) with inlet hose connection inbuilt float valve. Each 16 57982.00 927712.00 16.00 57982.00 927712
2 Nos. outlet foucet, drain tray with waste and pipe up to fllor trap heavy
compressor and wire up to socket, 3 pin plug etc complete in all respect.
One No. CP brass Single Lever Concealed Diverter Make Jaquar Cat.
No. FON-40079K + ALD-079.
One No. CP brass OH shower head Make Jaquar Cat. No. OHS-1989 &
Shower Arm Make Jaquar No.SHA-483.
One No. CP brass Bath Spout Make Jaquar Cat. No. SPJ-81429.
Including cutting and making good the walls wherever required.
Shower set as described above. Each 12 7508.00 90096.00 12.00 7508.00 90096
2.0 Soil, Waste, Vent & Rain Water Pipes
2.4.1 Coupler
Providing and fixing to the inlet mouth of rain water pipe cast iron
2.5 Each 154 47.25 7276.50 154.00 47.25 7276.5
grating 15 cm diameter and weighing not less than 440 grams.
100 mm dia Centrifugally cast (spun) iron socket & spigot (S&S) pipe as
2.6.1 Metre 2729 825.00 2251425.00 2729.00 825.00 2251425
per IS: 3989
Providing and fixing bend of required degree with access door, insertion
2.7 rubber washer 3 mm thick, bolts and nuts complete. Sand cast iron S&S
as per IS - 3989.
2.10 Providing and fixing double equal plain junction of required degree.
2.10.1 100x100x100x100 mm
2.10.1.1 Sand cast iron S&S as per IS - 3989 Each 34 865.70 29433.80 34.00 865.70 29433.8
Providing and fixing single equal plain junction of required degree with
2.11 access door, insertion rubber washer 3 mm thick, bolts and nuts
complete.
2.11.1 100x100x100 mm
2.11.1.1 Sand cast iron S&S as per IS - 3989 Each 129 722.55 93208.95 129.00 722.55 93208.95
2.12 Providing and fixing single equal plain junction of required degree.
2.12.1 100x100x100 mm
2.12.1.1 Sand cast iron S&S as per IS - 3989 Each 361 667.70 241039.70 361.00 667.70 241039.7
2.13.1 100 mm
2.13.1.1 Sand cast iron S&S as per IS - 3989 Each 105 389.40 40887.00 105.00 389.40 40887
2.14.1 100 mm
2.14.1.1 Sand cast iron S&S as per IS - 3989 Each 62 409.45 25385.90 62 409.45 25385.9
Providing and fixing MS Stay clamps for sand cast iron/ centrifugally
2.16
cast (spun) iron pipes of diameter.
2.16.1 100 mm dia Each 105 126.50 13282.50 105.00 126.50 13282.5
Providing and fixing trap of self cleansing design with screwed down or
2.17 hinged with or without vent arm complete, including cost of cutting and
making good the walls and floors.
Painting sand cast iron/ centrifugally cast (spun) soil, waste, vent pipes
2.18 and fittings with paint of any colour such as chocolate grey, or buff etc.
over a coat of primer (of approved quality) for new work.
2.18.1 100 mm diameter pipe Metre 2729 64.20 175201.80 2729.00 64.20 175201.8
Providing and fixing G.I. pipes complete with G.I. fittings and clamps,
2.19
i/c cutting and making good the walls etc. (Internal work)
2.19.1 32 mm dia nominal bore Metre 385 529.70 203934.50 385.00 529.70 203934.5
2.19.2 40 mm dia nominal bore Metre 132 639.60 84427.20 132.00 639.60 84427.2
2.19.3 50 mm dia nominal bore Metre 251 786.75 197474.25 251.00 786.75 197474.25
2.20.1 32 mm dia. nominal bore Metre 385 17.05 6564.25 385.00 17.05 6564.25
2.20.2 40 mm dia. nominal bore Metre 132 19.40 2560.80 132.00 19.40 2560.8
2.20.3 50 mm dia. nominal bore Metre 251 23.35 5860.85 251.00 23.35 5860.85
2.21.1 For 100 mm dia pipe Each 835 287.45 240020.75 835.00 287.45 240020.75
2.21.2 For 75 mm dia pipe Each 29 283.40 8218.60 29.00 283.40 8218.6
2.23.1 For 150 mm dia Pipe (Thickness of clamp 2.0 mm) Each 32 319.00 10208.00 32.00 319.00 10208
Providing and fixing cast brass floor clean out plug with suitable insert
keys for opening, male threaded joint with GI threaded socket drip seal
2.24
to soil / waste pipe of CI pipe as required complete as per drawing
approved sample and direction of engineer in charge.
Providing and fixing 100 mm dia GI inlet fitting/ Extension Piece with 2
2.26 or 3 inlets of 32 to 50 mmdia, fixed to CI trap with lead joint and set in Each 338 787.00 266006.00 338.00 787.00 266006
cement concrete as per drawing complete.
3.1.1 15 mm nominal outer dia .Pipes. Metre 2030 260.00 527800.00 2030.00 260.00 527800
3.1.2 20 mm nominal outer dia .Pipes. Metre 985 300.00 295500.00 985.00 300.00 295500
3.1.3 25 mm nominal outer dia .Pipes. Metre 655 350.00 229250.00 655.00 350.00 229250
3.1.4 32 mm nominal outer dia .Pipes. Metre 310 440.00 136400.00 310.00 440.00 136400
3.1.5 40 mm nominal outer dia .Pipes. Metre 100 440.00 44000.00 100.00 440.00 44000
Providing and fixing G.I. pipes complete with G.I. fittings and clamps,
3.2
i/c cutting and making good the walls etc.
Internal work - Exposed on wall
3.2.1 15 mm dia nominal bore Metre 105 284.90 29914.50 105 284.9 29914.5
3.2.2 20 mm dia nominal bore Metre 665 344.10 228826.50 665 344.1 228826.5
3.2.3 25 mm dia nominal bore Metre 960 438.00 420480.00 960 438 420480
3.2.4 32 mm dia nominal bore Metre 830 529.70 439651.00 830 529.7 439651
3.2.5 40 mm dia nominal bore Metre 810 639.60 518076.00 810 639.6 518076
3.2.6 50 mm dia nominal bore Metre 595 786.75 468116.25 595 786.75 468116.25
3.2.7 65 mm dia nominal bore Metre 140 1076.00 150640.00 140 1076 150640
3.2.8 80 mm dia nominal bore Metre 35 1252.00 43820.00 35 1252 43820
0 0
Providing and fixing gun metal gate valve with C.I. wheel of approved
3.3 0 0
quality (screwed end) :
0 0
3.3.1 20 mm dia nominal bore Each 195 460.20 89739.00 195 460.2 89739
3.3.2 25 mm dia nominal bore Each 102 497.15 50709.30 102 497.15 50709.3
3.3.3 32 mm dia nominal bore Each 50 581.25 29062.50 50 581.25 29062.5
3.3.4 40 mm dia nominal bore Each 24 678.40 16281.60 24 678.4 16281.6
3.3.5 50 mm dia nominal bore Each 10 869.20 8692.00 10 869.2 8692
3.3.6 65 mm dia nominal bore Each 5 1488.10 7440.50 5 1488.1 7440.5
3.3.7 80 mm dia nominal bore Each 3 2217.90 6653.70 3 2217.9 6653.7
Painting G.I. pipes and fittings with synthetic enamel white paint with
3.4 two coats over a ready mixed priming coat, both of approved quality for
new work :
3.4.1 15 mm dia nominal bore Metre 105 15.20 1596.00 105.00 15.20 1596
3.4.2 20 mm dia nominal bore Metre 665 18.15 12069.75 665.00 18.15 12069.75
3.4.3 25 mm dia nominal bore Metre 959 23.70 22728.30 959.00 23.70 22728.3
3.4.4 32 mm dia nominal bore Metre 830 28.40 23572.00 830.00 28.40 23572
3.4.5 40 mm dia nominal bore Metre 810 33.40 27054.00 810.00 33.40 27054
3.4.6 50 mm dia nominal bore Metre 591 39.80 23521.80 591.00 39.80 23521.8
3.4.7 65 mm dia. nominal bore Metre 125.69 42.00 5278.98 125.69 42.00 5278.98
3.4.8 80 mm dia. nominal bore Metre 35 49.00 1715.00 35.00 49.00 1715
Providing and placing on terrace (at all floor levels) polyethylene water
storage tank lSI: 12701 marked(Sintex or equivalent) with cover and
3.5 suitable locking arrangement and making necessary holes for inlet, outlet Litre 79500 6.25 496875.00 79500 6.25 496875
and overflow pipes but without fittings and the base support for tank
complete as per direction of Engineer-in-charge.
3.6.1 For 20 mm dia Pipe 6 mm thick (Concealed Pipes) Metre 610 54.00 32940.00 610.00 54.00 32940
3.6.2 For 25 mm dia Pipe 6 mm thick (Concealed Pipes) Metre 120 58.00 6960.00 120.00 58.00 6960
3.6.3 For 32 mm dia Pipe 9 mm thick (Concealed Pipes) Metre 80 89.00 7120.00 80.00 89.00 7120
Providing and fixing Thermoflex or Kaiflex thermal insulation tubing, a
elastomeric flexible material having hermetic blister closed cell structure
of expanded synthetic rubber over pipes of following nominal bores and
3.7
thickness including protection by wrapping with 24 gauge alumminium
sheet with riveted screw joints all required accessories complete as per
specification.
3.7.1 For 20 mm dia Pipe Metre 125 102.00 12750.00 125.00 102.00 12750
3.7.2 For 25 mm dia Pipe Metre 200 120.00 24000.00 200.00 120.00 24000
3.7.3 For 32 mm dia Pipe Metre 80 139.00 11120.00 80.00 139.00 11120
Providing and fixing forged brass single acting air release valve with
3.8 Each 22 726.00 15972.00 22.00 726.00 15972
screwed inlet 25 mm dia.
10 Nos. Solar Flat Plate collector having collector area should be min. 2
Sq, Mtr. (Collectror should be BIS & MNRE approved.
One No. Horizontal/Vertical hot water storage tank of 1000 ltr capacty
shall be made out by 4.0 mm thick stainless steel 316 grade,100 mm
thick rock wool/glass wool slab insulation (density of glass wool 64
Kg/Sqm.) covered with chicken mesh & 22 SWG aluminum sheet
cladding outside the tank. Tank shall be provided with flanges for inlet
outlet, over flow/ drain connection & Vent pipe with M H cover of 450
mm internal dia., Temperature and pressure release valve should be on
top of water storage tank
Providing and fixing a lot of Temperature Gauge, vent pipe, ball valve,
NRV, CI/brass Y strainer, PT - 100 sensors with thermocople wire ,MS.
Angle stand for hot water tank .
One No. Heat Exchanger cage type inbuild the hot water storage tank of
SS 316 having surface area not less than 2.4 Sq. Mtr.
One No. Control Panel for electric heaters & recirculation pump having
DTC with contractor, MCBs, and cycling timer for pump.
4.1.1 Solar System as described above Set 5 333699.00 1668495.00 5.00 333699.00 1668495
C INTERNAL ELECTRIFICATION
A PART (A) - SCHEDULED ITEMS ( AS PER UP SOR 2018)
1 Wiring point for light with 1.5 sq.mm FR P.V.C. insulated multistrand
single core Copper Conductor cable in thick PVC conduit pipe
partly concealed in wall & partly laid in slab along with the
reinforcement before concreting complete with 1.5 Sq.mm copper earth
continuity wire & modular type switch & ceiling rose / angle / batten NOS 2686.00 654.00 1756644.00 2686.00 654.00 1756644
holder on 3 mm thick phenolic laminated backelite sheet etc complete in
all respects as directed, including matching color wash.
2 Wiring point for two way light with 1.5 sq.mm FR P.V.C. insulated
multistrand single core Copper Conductor cable in thick PVC
conduit pipe partly concealed in wall & partly laid in slab along with
the reinforcement before concreting complete with 1.5 Sq.mm copper
earth continuity wire and two no two way modular type switchws & NOS 52.00 956.00 49712.00 52.00 956.00 49712
ceiling rose / angle / batten holder on 3 mm thick phenolic laminated
backelite sheet etc complete in all respects as directed, including
matching color wash
3 Wiring point for fan/fresh air fan (light duty exhaust/ Ceiling fan)
with 1.5 sq.mm FR P.V.C. insulated multistrand single core Copper
Conductor cable in thick PVC conduit pipe partly concealed in wall
& partly laid in slab along with the reinforcement before concreting
complete with 1.5 Sq.mm copper earth continuity wire & modular type
switch & ceiling rose / angle / batten holder on 3 mm thick phenolic NOS 1167.00 715.00 834405.00 1167 715 834405
laminated backelite sheet etc complete in all respects as directed,
including matching color wash.
4 Wiring point for plug with 1.5 sq.mm FR P.V.C. insulated multistrand
single core Copper Conductor cable in thick PVC conduit pipe partly
concealed in wall & partly laid in slab along with the reinforcement
before concreting complete with 1.5 Sq.mm copper earth continuity wire
& modular type switch & socket etc complete in all respects including NOS 1383.00 410.00 567030.00 1383.00 410.00 567030
matching color wash.
5 Wiring point for call bell with 1.5 sq.mm FR P.V.C. insulated
multistrand single core Copper Conductor cable in thick PVC conduit
pipe partly concealed in wall & partly laid in slab along with the
reinforcement before concreting complete with 1.5 Sq.mm copper earth
NOS 30.00 652.00 19560.00 30.00 652.00 19560
continuity wire & modular type bell push or 2 pin socket etc complete
in all respects including matching color wash
6 Supply and fixing of power plug with 15A/250 volt flush type switch and
5 pin 15A/250V flush type universal socket in suitable M.S. box of
175mm x 100mm x 50mm size with phenolic laminated bakelite sheet
cover 3mm thick fixed with brass machine screw and cup washer. NOS 776.00 340.00 263840.00 776.00 340.00 263840
7 Supply and fixing of power plug with 20 Amp./250 volt flush type
modular switch and 5 pin 20 A/250 volt flush type universal modular
socket switch on concealed M.S box including supply of all material,
labour T&P etc. required for proper completion of work. NOS 238.00 625.00 148750.00 238.00 625.00 148750
a 2 x 1.5 sq. mm. with 1.5 sq.mm earth wire In 20 mm dia conduit. M 4270.00 121.00 516670.00 4270.00 121.00 516670
b 2 x 2.5 sq. mm. with 1.5 sq.mm earth wire In 20 mm dia conduit. M 46300.00 149.00 6898700.00 46300.00 149.00 6898700
c 2 x 4 sq. mm. with 2.5 sq. mm earth wire In 25mm dia conduit. M 27955.00 204.00 5702820.00 27955.00 204.00 5702820
d 2 x 6 sq. mm. with 4 sq. mm earth wire In 32mm dia conduit. M 7405.00 272.00 2014160.00 7405.00 272.00 2014160
e 2 x 10 sq. mm. with 6 sq. mm earth wire In 32mm dia conduit. M 1450.00 395.00 572750.00 1450.00 395.00 572750
f 2 x 16 sq. mm.with 10 sq. mm earth wire In32mm dia conduit. M 1675.00 463.00 775525.00 1675.00 463.00 775525
g 4 x 6 sq. mm. with 2 x 4 sq. mm earth wire In 32mm dia conduit. M 1050.00 360.00 378000.00 1050.00 360.00 378000
h 4 x 10 sq. mm.with 2 x 6 sq. mm earth wire In 32mm dia conduit. M 3900.00 505.00 1969500.00 3900.00 505.00 1969500
i 4 x 16 sq. mm. with 2 x 10 sq. mm earth wire In 32mm dia conduit.
M 3150.00 723.00 2277450.00 3150.00 723.00 2277450
10 Supply fixing and concealing 2mm thick PVC conduit pipe with ISI
mark embossed and with PVC accessories confirming to IS no 3419 for
drawing wires duly sealed at joints with original resin/ adhesive to make
the complete piping rigid, plastering with cement sand mortar finised to
the level with matching colour wash including cost of all material labour
and T&P etc required for proper completion of work. (for Telephone /
Television / circuits)
20 mm dia. conduit (16 SWG) thick M 6440.00 62.00 399280.00 6440.00 62.00 399280
25 mm dia. conduit (16 SWG) thick M 2715.00 72.00 195480.00 2715.00 72.00 195480
32 mm dia. conduit (16 SWG) thick M 1175.00 87.00 102225.00 1175.00 87.00 102225
11 S/F of surface/flush mounting SPN distribution board with additional
metal door without MCB complete in all respect as directed at site by
Engineer-in-charge..
S&F of 160 Amp 4 Pole MCCB (25KA) thermal magnetic release (Cat
18 each 13.00 12660.00 164580.00 13.00 12660.00 164580
A)
Eraction and testing of ceiling fan and regulator for room height upto 3.5
19 meters including including supply of 3mm thick GI pipe 19mm dia, Duly each 905.00 140.00 126700.00 905.00 140.00 126700
painted, completed in all respect.
Add extra to item (1116) for 15cm or part there of for room height from
20 each 0.00 40.00 0.00 0.00 40.00 0
3.5 to 5.00 meter.
21 Erection and testing of exhaust/ wall fan on the existing hole with
suitable size of rag bolts nuts and washers etc complete in all respects.
NOS 237.00 195.00 46215.00 237.00 195.00 46215
25 S/F of danger board fabricated from 10 gauge M.S. sheet as per E/I
NOS 12.00 85.00 1020.00 12 85 1020
rules.
26 S/F of shock treatment chart ( prescribed under I.E.rules ) duly
framed with glass and supported from back with hard board or soft
board with supply of all material labour T & P etc for proper completion NOS 12.00 305.00 3660.00 12.00 305.00 3660
of work.
38 S&F of 63 Amp. four pole change over switch on 40mm x 40mm x 6mm
angle iron frame, including the cost of labour, T&P, painting and other
NOS 3.00 4760.00 14280.00 3.00 4760.00 14280
material required for proper completion of the work as per direction and
satisfaction of Engineer in charge.
39 Supply and fixing of recess/surface/ Pendent mounting round 6 Watt to 8
Watt LED Down Lighter having Powder coated die cast aluminium
Each 227.00 770.00 174790.00 227.00 770.00 174790
housing with extended heat sink, diffuser/ Reflector and driver set
completed in all respects. ( CAT - AAA )
40 Supply and fixing of recess/surface/ Pendent mounting round 10 Watt to
15 Watt LED Down Lighter having Powder coated die cast aluminium
Each 1185.00 1350.00 1599750.00 1185.00 1350.00 1599750
housing with extended heat sink, diffuser/ Reflector and driver set
completed in all respects. ( CAT - AAA )
41 Supply and fixing of LED tube light with batten suitable for uo to 1 x 22
watt LED tube light fitting including tube on surface completein all Each 1386.00 1190.00 1649340.00 1386.00 1190.00 1649340
respect. (CAT - AAA)
42 Supply and fixing of single LED light wall bracket 3 to 6 watt on
matching M.D.F.E.G Board base etc. completed in all respects. ( CAT - Each 378.00 2600.00 982800.00 378.00 2600.00 982800
AAA )
43 Supply and fixing of water tight oblong 10 Watt LED bulkhead luminaire
with driver set confirming to IP 65 as above Protection . complete in all Each 72.00 1400.00 100800.00 72.00 1400.00 100800
respect.( CAT AAA )
44 Supply and fixing of factory wired integral LED flood light luminaires
with die cast aluminium housing built with dirver set suitable for 140 to
Each 34.00 13190.00 448460.00 34.00 13190.00 448460
150 Watt. Confirming to IP 66 protection complete in all respect.
1200 mm sweep, 50W, 350 RPM Nos 900.00 2107.00 1896300 900 2107 1896300
4 Supply of AC 230/250 volts, 50 HZ exhaust fan including providing
nuts, bolts, mounting frame and other accessories etc. complete
250 mm sweep 1250 rpm Nos 223.00 2348.00 523604 223 2348 523604
5 Supply of AC 230/250 volts, 50 HZ Wall fan including providing nuts,
bolts, mounting frame and other accessories etc. complete
400 mm sweep 1350 rpm Nos 41.00 2348.00 96268 41 2348 96268
Incoming
400A FP 35kA MCCB with thermal magnetic release with adjustable
OL, SC and EF protection - 1 nos.
1- set Red/Green ON/OFF indicating lamps
1- set of three phase (red, yellow, blue) indicating lamps
Amber healthy trip indicating lamps
1 nos MFM
Bus Bars
Electrolytic high conductivity Aluminium three phase and neutral
busbars rated at 600 A having a maximum current density of 1.0 A per
sq mm suitable to with stand symmetrical fault level of 35kA at 415 V.
Outgoings
160 A, 4P 35 KA MCCB -- 1 no
100 A, 4P 35 KA MCCB -- 4 no
63 A, 4P 35 KA MCCB -- 2 no
The switchboard shall be complete with all inter connections, risers,
each 3.00 350000.00 1050000 3 350000 1050000
internal wiring, labels etc complete as required
Linear pneumatic heat Detection Tube with all necessary fittings &
Meter 135.00 2056.00 277560 135 2056 277560
supports.
Master Control Unit for controllin each system, complete with pressure
switches, buzzers and electronic hooters, including all necessary
No. 9.00 5277.00 47493 9 5277 47493
acessories +electrical writing to make each entire system functional.
7 FLOOR PANEL
Supply, installation, testing & commissioning of front operated front
access cuibical type indoor duly floor / wall / recess / surface mounting,
totally enclosed dust and vermin proof (minimum protection IP 54)
panels with neoprene gaskets, fabricated from 2mm thick CRCA sheets
with powder coated finish (minimum thickness 50 micron)suitable for
415 volts 3 phase 4 wire 50 Hz system to withstand syummetrical fault
level of 35 kA at 415V, 3 phase, 4 wire, 50 Hz system including 0 0
interconnections, bonding to earth etc. and flush door conforming to
relevant IS standard including complete as per specification & drawings
as required and as given below. All internal wiring in the panels shall be
carried out using FRPVC swires capable of withstanding high
temperature. panel shall be approved by architect.
Incoming 0 0
100A FP 25kA MCCB with thermal magnetic release with adjustable
0 0
OL, SC and EF protection - 1 nos.
1- set Red/Green ON/OFF indicating lamps
1- set of three phase (red, yellow, blue) indicating lamps
Amber healthy trip indicating lamps
1 nos MFM
Bus Bars
Electrolytic high conductivity Aluminium three phase and neutral
busbars rated at 200 A having a maximum current density of 1.0 A per
sq mm suitable to with stand symmetrical fault level of 25kA at 415 V.
Outgoings
63 A, 4P 35 KA MCB -- 5 no
40 A, 4P 10 KA MCB -- 2 no
The switchboard shall be complete with all inter connections, risers,
each 5.00 195000.00 975000 5 195000 975000
internal wiring, labels etc complete as required
Incoming
100A FP 25kA MCCB with thermal magnetic release with adjustable
OL, SC and EF protection - 1 nos.
1- set Red/Green ON/OFF indicating lamps
1- set of three phase (red, yellow, blue) indicating lamps
Amber healthy trip indicating lamps
1 nos MFM
Bus Bars
Electrolytic high conductivity Aluminium three phase and neutral
busbars rated at 200 A having a maximum current density of 1.0 A per
sq mm suitable to with stand symmetrical fault level of 25kA at 415 V.
Outgoings
63 A, 4P 35 KA MCB -- 5 no
40 A, 4P 10 KA MCB -- 2 no
The switchboard shall be complete with all inter connections, risers,
each 4.00 155000.00 620000 4 155000 620000
internal wiring, labels etc complete as required
7B DG PANEL
Supply, installation, testing & commissioning of front operated front
access cuibical type indoor duly floor / wall / recess / surface mounting,
totally enclosed dust and vermin proof (minimum protection IP 54)
panels with neoprene gaskets, fabricated from 2mm thick CRCA sheets
with powder coated finish (minimum thickness 50 micron)suitable for
415 volts 3 phase 4 wire 50 Hz system to withstand syummetrical fault
level of 35 kA at 415V, 3 phase, 4 wire, 50 Hz system including
interconnections, bonding to earth etc. and flush door conforming to
relevant IS standard including complete as per specification & drawings
as required and as given below. All internal wiring in the panels shall be
carried out using FRPVC swires capable of withstanding high
temperature. panel shall be approved by architect.
Incoming
100A FP 25kA MCCB with thermal magnetic release with adjustable
OL, SC and EF protection - 1 nos.
1- set Red/Green ON/OFF indicating lamps
1- set of three phase (red, yellow, blue) indicating lamps
Amber healthy trip indicating lamps
1 nos MFM
Bus Bars
Electrolytic high conductivity Aluminium three phase and neutral
busbars rated at 200 A having a maximum current density of 1.0 A per
sq mm suitable to with stand symmetrical fault level of 25kA at 415 V.
Outgoings
63 A, 4P 10 KA MCB -- 5 no
40A, DP 10 KA MCB -- 2 no
The switchboard shall be complete with all inter connections, risers,
each 1.00 125000.00 125000 1 125000 125000
internal wiring, labels etc complete as required
8 UPS PANEL
Supply, installation, testing & commissioning of front operated front
access cuibical type indoor duly floor / wall / recess / surface mounting,
totally enclosed dust and vermin proof (minimum protection IP 54)
panels with neoprene gaskets, fabricated from 2mm thick CRCA sheets
with powder coated finish (minimum thickness 50 micron)suitable for
415 volts 3 phase 4 wire 50 Hz system to withstand syummetrical fault
level of 35 kA at 415V, 3 phase, 4 wire, 50 Hz system including 0 0
interconnections, bonding to earth etc. and flush door conforming to
relevant IS standard including complete as per specification & drawings
as required and as given below. All internal wiring in the panels shall be
carried out using FRPVC swires capable of withstanding high
temperature. panel shall be approved by architect.
Incoming 0 0
63A FP 25kA MCCB with thermal magnetic release with adjustable OL,
0 0
SC and EF protection - 1 nos.
1- set Red/Green ON/OFF indicating lamps 0 0
1- set of three phase (red, yellow, blue) indicating lamps 0 0
Amber healthy trip indicating lamps 0 0
1 nos MFM 0 0
Bus Bars
Electrolytic high conductivity Aluminium three phase and neutral
busbars rated at 100 A having a maximum current density of 1.0 A per
sq mm suitable to with stand symmetrical fault level of 25kA at 415 V.
Outgoings
40 A, 4P 10 KA MCB -- 4 no
40 A, SP 10 KA MCB -- 2 no
The switchboard shall be complete with all inter connections, risers,
each 6.00 120000.00 720000 6 120000 720000
internal wiring, labels etc complete as required
EXTRA ITEMS
UPS
1 Supply, installation, testing and commissioning and testing of 20KVA
N+1, 415V, 3ph input & 3 ph output ON-LINE UPS system back up
protection for 30 minutes as per EN/ IEC standared with all accessories
as required.
Details of UPS :-
(IGBT based rectifier & inverter) True Online UPS Systems having 30
Minutes battery Backup with each UPS System with MS Rack, Interlink
Cables and DC cables with all accessories. UPS shall be provided with
SNMP protocol for BMS interface.
Details of SMF Batteries:-
Sealed Maintenance free (SMF) Batteries for 30 Mins. backup with open
type MS Rack for installation of batteries and their respective battery
leads copper cables / Interlink between batteries, copper cables between
UPS & batteries, DC Isolator, with suitable size of Rack for batteries (as
per battery manufacturer's standard) and etc. as required. Make :- Exide
/ Quanta/ Amaron.
Total cost of 100 KVA UPS with batteries and other acessories
each 3.00 360000.00 1080000 3 360000 1080000
DG SET
2 Supply, installation, testing and commissioning of 200 kVA 415V Diesel
Generating Set with AMF Control Panel, Water cooled, three phase as
Nos 1.00 2550000.00 2550000 1 2550000 2550000
Per CPWD specification and CPCB-II Norms with minimum 1 years
warranrty as per OEM specifications.
IP EPABAX SYSTEM 0 0
3 Supply,installation,testing and commisioning of Redundant IP based on
IP core with hot standby configuration & geographical redundancy
support . System shall support Busy hour call completion 3,00,000.0
calls . IPv6 support from day 1 and model shall be TEC approved along
with the following specifications:
1. 100 IP Extensions with CLI Expandable to 250 Ports
2. 16 IP Port trunk with CLI and Power Failure Transfer and with
Protection modules.
3. 02 PRI. Nos 2.00 1550000.00 3100000 2 1550000 3100000
4. 02 nos Operator Console with 30 Direct selection Keys each.
5. 08 Port Voice Guidance to announce Extension Busy status, Wake up
call announcement and other important telephone features, Auto
Attendant facility for Welcome message announcement.
6. 02Nos -100 pair MDF(wall mountable)
7. 01 No. Call Billing and monitoring Software.
8. Charger/UPS with Batteries for backup of 1 hour.
LAN SYSTEM 0 0
3A Supply, installation, testing and commissioning of 63 kVA 415V Diesel
Generating Set with AMF Control Panel, Water cooled, three phase as
No 1.00 6,05,000.00 605000 1 605000 605000
Per CPWD specification and CPCB-II Norms with minimum 1 years
warranrty as per OEM specifications.
4 Supply,installation,testing and commisioning of 12 port unmanaged
No 13.00 21,865.00 284245 13 21865 284245
ethernet switch with 2 nos fiber ports
5 Supply,installation,testing and commisioning of 24 port unmanaged
No 28.00 32,889.00 920892 28 32889 920892
ethernet switch with 2 nos fiber ports
6 Supply,installation,testing and commisioning of Cat-6 shuttered 12 port
No 10.00 4,111.00 41110 10 4111 41110
fully loaded patch panel with 2 nos fiber ports
7 Supply,installation,testing and commisioning of 24 port Patch panel
No 39.00 4,581.00 178659 39 4581 178659
fully loaded, Cat-6 UTP Keystone Type.
8 Supply,installation,testing and commisioning of Cat-6 UTP 24AWG
No 1250.00 288.00 360000 1250 288 360000
patch cord, 1 meter, Plug 30U, snaglless etc as required.
9 Supply,installation,testing and commisioning of Cat-6 UTP 24AWG
No 204.00 327.00 66708 204 327 66708
patch cord, 2 meter, Plug 30U, snaglless etc as required.
10 Supply , Installation , Testing and Commissioning of 24 PoE
10/100/1000 BaseT, 2 SFP+ 1G/10G ports, one expansion slot. Includes
No 11.00 54,815.00 602965 11 54815 602965
an internal 390W PoE PSU, power cord, manuals access card, RJ-45 to
DB-9 adaptor with 2 nos fiber ports
11 Supply,installation,testring and commisioning of Floor mounted 42 U
Server Rack along with all standard accessories 800mm (W), 800mm
(D), approx. Wt.150 Kg, CRCA 'D' grade 1.6mm thick sheet, pwoder
coated for cabinet RAL- 9002, 4mm Toughened Tinted Glass Door and
along with following accessories:-
1. Cooling fan 220/230V AC, of 90 CFM-------4 Nos.
2. Cable manager Metal 4 Nos.
3. PDU- 230V /AC 1 No.
4. Cable Channel 100mm wide. 2 Nos.
5. Heavy Duty Stationary Shelf 600mm(W)X475mm(D) -1
6. Mounting Hardware (20 Sets of M-6 screws, washers,cage, nuts
(Nickle Coated)- 3 Nos.
7. Earthing strips copper 150mm H 1 No.
8. Door Lock 1 No.
9. Caster Wheels (with breake) 2 Nos.
10. Caster Wheels (without breake) 2 Nos.
11. Front Metal Band 1 No
42 U Network Rack as mention above No 5.00 85,374.00 426870 5 85374 426870
12 Supply,installation,testring and commisioning of 24 port LIU with SFP
Modules with 1 U rack size(SC)-SM having LC connection with all
No 6.00 21,988.00 131928 6 21988 131928
accessories including splice tray, LC adapter plate and pigtail.
27 SITC of Infrared Cable for Integration with IR Devices Each 2.00 2959 5918.367 2 2959.1835 5918.367
28 Supply Installation Testing & Commissioning of 8 Port Wifi Router Each 2.00 3551 7102.29975 2 3551.149875 7102.29975
Supply Installation Testing & Commissioning of Blu ray DVD Player
29 Each 2.00 6659 13317.6225 2 6658.81125 13317.6225
Supply & Fixing of 2 Core 1.5 Sq MM Speaker Cables. Flexible Copper
30 Conductor of cross section 1.5 Sq. mm / 2.5 Sq. mm insulated, RM 200.00 61 12189.45 200 60.94725 12189.45
PVCFRLS sheathed control Cable as per IS 694
31 Supply & Fixing of 18 AWG -24/0.20mm x 2 core Microphone Cable
RM 100.00 62 6224.4 100 62.244 6224.4
32 Supply & Fixing connectors required Lot 2.00 36992 73984.7745 2 36992.38725 73984.7745
33 Supply,installation,testring and commisioning of 12U rack with Front
glass door, Rear Perforated door with handle Lock & key. Front/Rear 19"
Each 2.00 3575 7150 2 3575 7150
mounting angles, top, bottom open, RAL 9005 with all other accessories
DCC controllers for VRV system centerlized controller Lot 0.00 552148 0 0 552147.75 0
DCC controllers for pressurization system Nos. 0.00 64785 0 0 64785 0
DCC controllers for ventilation fans (DDC/IO module) Lot 2.00 383657 767313 2 383656.5 767313
DCC controllers for DG system Lot 1.00 64785 64785 1 64785 64785
DCC controllers for LT Energy Meters/Breakers Lot 7.00 58896 412272 7 58896 412272
DCC controllers for Water tanks Lot 0.00 58896 0 0 58896 0
DCC controllers for Lifts Lot 4.00 58896 235584 4 58896 235584
SYSTEM INTEGRATION UNITS FOR 3RD PARTY SYSTEM
SOFTWARE INTEGRATION - UL listed Controllers. 0.00 0 0 0
1 S/F of danger board fabricated from 10 gauge M.S. sheet as per E/I
NOS 5.00 85.00 425.00 5 85 425
rules.
2 S/F of shock treatment chart ( prescribed under I.E.rules ) duly
framed with glass and supported from back with hard board or soft
board with supply of all material labour T & P etc for proper completion NOS 10.00 305.00 3050.00 10 305 3050
of work.
13 Supply and fixing of one number 8 SWG G.I. wire in 15mm dia G.I. pipe
for earthing, laid in ground or in wall duty concealed including the cost
of cement, sand, labour, T&P other material required for proper M 4000.00 200.00 800000.00 4000 200 800000
completion of the work as directed at site.
14 Supply and fixing of decorative 40 to 45 Watt LED Post top indirect light
luminaire having Pressure die cast aluminium body and Clear glass with
Each 4.00 8410.00 33640.00 4 8410 33640
driver set
confirming to IP 65 and above protection complete in all respect.
15 Supply and fixing of factory wired integral LED flood light luminaires
with die cast aluminium housing built with dirver set suitable for 140 to
Each 36.00 13190.00 474840.00 36 13190 474840
150 Watt. Confirming to IP 66 protection complete in all respect.
16 Supply and fixing of factory wired integral LED flood light luminaires
with die cast aluminium housing built with dirver set suitable for 170 to
Each 36.00 22750.00 819000.00 36 22750 819000
200 Watt. Confirming to IP 66 protection complete in all respect.
17 Supply & fixing of 6 mtr GI Octagonal Pole of approved make (top dia
70mm, Bottom dia 130mm and base plate 12mm thik) having 3mm
thikness with Single arm bracket 1 Mtr length in 1:2:4 RCC foundation Each 10.00 14750.00 147500.00 10 14750 147500
bolt including the cost of foundation, excavation & back filling and
Required T&P completee in all respect.
18 Supply & fixing of 9 mtr GI Octagonal Pole of approved make (top dia
70mm, Bottom dia 155 mm and base plate 12mm thik) having 3mm
thikness with single arm bracket (1 Mtr length) on RCC foundation
including the cost of foundation, foundation bolts, excavation & back Each 12.00 20890.00 250680.00 12 20890 250680
filling and Required T&P completee in all respect.
Total cost of 100 KVA UPS with batteries and other acessories
each 1.00 180000.00 180000 1 180000 180000
LAN SYSTEM 0.00 0 0 0
2 Supply,installation,testing and commisioning of 12 port unmanaged
No 2.00 21865.00 43730 2 21865 43730
ethernet switch with 2 nos fiber ports
3 Supply,installation,testing and commisioning of 24 port unmanaged
No 6.00 32889.00 197334 6 32889 197334
ethernet switch with 2 nos fiber ports
4 Supply,installation,testing and commisioning of Cat-6 shuttered 12 port
No 2.00 4111.00 8222 2 4111 8222
fully loaded patch panel with 2 nos fiber ports
5 Supply,installation,testing and commisioning of 24 port Patch panel
No 9.00 4581.00 41229 9 4581 41229
fully loaded, Cat-6 UTP Keystone Type.
6 Supply,installation,testing and commisioning of Cat-6 UTP 24AWG
No 200.00 288.00 57600 200 288 57600
patch cord, 1 meter, Plug 30U, snaglless etc as required.
7 Supply,installation,testing and commisioning of Cat-6 UTP 24AWG
No 46.00 327.00 15042 46 327 15042
patch cord, 2 meter, Plug 30U, snaglless etc as required.
8 Supply , Installation , Testing and Commissioning of 24 PoE
10/100/1000 BaseT, 2 SFP+ 1G/10G ports, one expansion slot. Includes
No 6.00 54815.00 328890 6 54815 328890
an internal 390W PoE PSU, power cord, manuals access card, RJ-45 to
DB-9 adaptor with 2 nos fiber ports
9 Supply,installation,testring and commisioning of Floor mounted 42 U
Server Rack along with all standard accessories 800mm (W), 800mm
(D), approx. Wt.150 Kg, CRCA 'D' grade 1.6mm thick sheet, pwoder 0.00 0 0 0
coated for cabinet RAL- 9002, 4mm Toughened Tinted Glass Door and
along with following accessories:-
1. Cooling fan 220/230V AC, of 90 CFM-------4 Nos. 0.00 0 0 0
2. Cable manager Metal 4 Nos. 0.00 0 0 0
3. PDU- 230V /AC 1 No. 0.00 0 0 0
4. Cable Channel 100mm wide. 2 Nos. 0.00 0 0 0
5. Heavy Duty Stationary Shelf 600mm(W)X475mm(D) -1 0.00 0 0 0
6. Mounting Hardware (20 Sets of M-6 screws, washers,cage, nuts
0.00 0 0 0
(Nickle Coated)- 3 Nos.
7. Earthing strips copper 150mm H 1 No. 0.00 0 0 0
8. Door Lock 1 No. 0.00 0 0 0
9. Caster Wheels (with breake) 2 Nos. 0.00 0 0 0
10. Caster Wheels (without breake) 2 Nos. 0.00 0 0 0
11. Front Metal Band 1 No 0.00 0 0 0
42 U Network Rack as mention above No 1.00 85374.00 85374 1 85374 85374
10 Supply,installation,testring and commisioning of 24 port LIU with SFP
Modules with 1 U rack size(SC)-SM having LC connection with all
No 2.00 21988.00 43976 2 21988 43976
accessories including splice tray, LC adapter plate and pigtail.
The item shall also include all necessary control and low power cabling
between the HT panel and LT panels.
In addition 33kV HT panel shall be with all requirements as per the
Nos 1.00 1550000.00 1550000 1 1550000 1550000
guidelines by Local E.B authorities and Electrical inspectorate.
MAIN PANEL
16 Supply, Installation, Testing & Commissioning of Main LT panel,
cubicle type, made out of min 2mm thick CRCA sheet (load bearing),
totally enclosed, IP42, free standing, floor mounting, dust and vermin
proof, powder coated, indoor, compartmentalised, suitable for operation
on 3 phase and neutral, 415 V, 50Hz AC system with busbars extendable
on both sides, including internal wiring with suitable size wires, rotary
handle, spreaders, 3mm thick gland plate, hinged type door with
neoprene / PU gasket, IS 8623 etc. The panel shall include supply &
installation of following switchgears, metering instruments and
accessories as per specification. The panel shall be suitable for receiving
Cable / Bus duct to the incomer ACB. Panel shall have potential free
contacts to interface with BMS.
Incomer
3000A, FP, 50kA, microprocessor based ACB electrical operated,
drawout type, motorised, with overload, instantaneous SC, delayed SC,
and ground fault protection with necessary communication port, shunt
trip coil, U/V release etc - 2 nos.
Neccesary provision and control cabling shall be done to trip LT panel
incomer on failure of 11kV HT supply.
Bus Coupler
3000A, FP, 50kA, ACB electrical operated, drawout type, motorised
with out protection with necessary communication port, shunt trip coil
etc - 1 no.
Busbar
8000 A TPN 50KA busbars of high conductivity electrolytic quality
copper alloy and suitable size earthing conductor through out the panel
for its earthing. Bus Bar Shall have 100% neutral.
Instruments
2A, C curve SP MCB - 4 set
RYB indication lamp, LED type - 4 set
On/Off, Trip indication lamp, LED type - 4 set
(0-500)V voltmeter, Digital type - 4 set
(0-2500)A ammeter, Digital type - 3 set
(0-1600)A ammeter, Digital type - 3 set
4 set 3 phase Digital Multi function meter to read V, A, F, kW, PF, kWH,
Acc class 1 and with necessary communication port
(Backnet/Modbus/RS:485) suited for BMS system
Low set earth fault relay using CT of 3000/5A 15VA Cl. 5P10 with
necessary control cable from CT at transformer neutral to 51G relay in
MSB panel- 2 set
3000/5A 15VA class 1 resin cast CT - 3 set
630/5A 15VA class 1 resin cast CT for connection to APFC panel -2 set
Outgoing.
1250A, FP, 50kA, microprocessor based ACB electrical operated,
drawout type, motorised, with overload, instantaneous SC, delayed SC,
and ground fault protection with necessary communication port, shunt
trip coil, U/V release etc - 2 nos.
800A, FP, 50kA, microprocessor based ACB electrical operated, drawout
type, motorised, with overload, instantaneous SC, delayed SC, and
ground fault protection with necessary communication port, shunt trip
coil, U/V release etc - 1 nos.
630A FP 50kA MCCB with microprocessor based release with
adjustable OL, SC and EF protection - 2 no.
400A FP 50kA MCCB with microprocessor based release with
adjustable OL, SC and EF protection - 2 no.
200A FP 50kA MCCB with microprocessor based release with
adjustable OL, SC and EF protection - 4 nos.
100A FP 50kA MCCB with microprocessor based release with
adjustable OL, SC and EF protection - 2 nos.
All outgoings expect capcitor panel shall have 3 phase Digital Multi
function meter to read V, A, F, kW, kWh with Acc class 1 including
respective feeder rating CT on the outgoing feeders
The switchboard shall be complete with all inter connections, risers,
Nos 1.00 2550000.00 2550000 1 2550000 2550000
internal wiring, labels etc complete as required
17 Supply, Installation, Testing & Commissioning of 600 kVAR APFC
panel, cubicle type, made out of min 2mm thick CRCA sheet (load
bearing), totally enclosed, IP42, free standing, floor mounting, dust and
vermin proof, powder coated, indoor, compartmentalised, suitable for
operation on 3 phase and neutral, 415 V, 50Hz AC system, including
internal wiring with suitable size wires, rotary handle, spreaders 3mm
thick gland plate, hinged type door with neoprene / PU gasket etc. The 0.00 0 0 0
panel shall include supply & installation of following switchgears,
metering instruments and accessories as per specification. Required nos.
of louvers and panel mounted cooling fans with auto/ manual control
shall be provided.
Incomer 0.00 0 0 0
1600A, FP, 50kA, microprocessor based ACB electrical operated,
drawout type, motorised, with overload, instantaneous SC, delayed SC,
and ground fault protection with necessary communication port, shunt
trip coil, U/V release etc - 1 nos.
Busbar
1 Set of 2000 Amp TPN busbars of high conductivity electrolytic quality
Aluminium alloy and suitable size earthing conductor through out the
panel for its earthing.
Instruments
1 No 3 phase Digital Multi function meter to read V, A, F with Acc class
1.
1 Set of phase indicating lamps, LED type, RYB.
1 Set of 2A 10kA C curve SP control MCB
1 Set of 800/5A, Class 1.0, 5VA, Cast Resin CT for metering.
1 no. 8 stage APFC relay
7 set On, Off push button
7 set On, Off LED type indication lamp
1 set Auto / manual selector switch.
Outgoing.
2 Nos 250A, TPN, 35kA, MCCB with Thermal Magnetic release, having
adjustable OL & SC protection.
4 Nos 100A, TPN, 35kA, MCCB with Thermal Magnetic release, having
adjustable OL & SC protection.
4 Nos 63A, TPN, 35kA, MCCB with Thermal Magnetic release, having
adjustable OL & SC protection.
2 Nos. 100 kVAR MPP heavy duty capacitor with capacitor duty
contactor & 7% detuned harmonic filter.
4 Nos. 50kVAR MPP heavy duty capacitor with capacitor duty contactor
& 7% detuned harmonic filter.
3 No. 25 kVAR MPP heavy duty capacitor with capacitor duty contractor
and 7% detuned harmonic filter.
1 No. 25 kVAR MPP heavy duty capacitor with 7% detuned harmonic
Nos 2.00 720000.00 1440000 2 720000 1440000
filter directly connected.
Incomer
200A FP 35kA MCCB with microprocessor based release with
adjustable OL, SC and EF protection - 1 nos.
Busbar
1 Set of 250 A TPN busbars of high conductivity electrolytic quality
Aluminium alloy and suitable size earthing conductor through out the
panel for its earthing.
Instruments
2A, C curve SP MCB - 3 nos.
RYB indication lamp, LED type - 3 nos.
1 No 3 phase Digital Multi function meter to read V, A, F, kW, kWh,
Acc class 1.
250/5A 5VA class 1 resin cast CT - 1 set
Outgoing.
63 A FP 25 kA MCCB, microprocessor based release having adjustable
Nos 1.00 180000.00 180000 1 180000 180000
O/L, SC protection - 7 nos.
19 Supply, Installation, Testing & Commissioning of Utility Panel, cubicle
type, made out of min 2mm thick CRCA sheet (load bearing), totally
enclosed, IP42, free standing, floor mounting, dust and vermin proof,
powder coated, indoor, compartmentalised, suitable for operation on 3
phase and neutral, 415 V, 50Hz AC system, including internal wiring
with suitable size wires, rotary handle, spreaders, 3mm thick gland plate,
hinged type door with neoprene / PU gasket, IS 8623 etc. The panel
shall include supply & installation of following switchgears, metering
instruments and accessories as per specification.
Incomer
630A FP 35kA MCCB with microprocessor based release with
adjustable OL, SC and EF protection - 1 nos.
Busbar
1 Set of 650 A TPN busbars of high conductivity electrolytic quality
Aluminium alloy and suitable size earthing conductor through out the
panel for its earthing.
Instruments
2A, C curve SP MCB - 3 nos.
RYB indication lamp, LED type - 3 nos.
1 No 3 phase Digital Multi function meter to read V, A, F, kW, kWh,
Acc class 1.
630/5A 5VA class 1 resin cast CT - 1 set
Outgoing.
250A FP 35kA MCCB with microprocessor based release with
adjustable OL, SC and EF protection - 2 nos.
200 A 4P 35kA MCCB,microprocessor based release having adjustable
O/L, SC protection - 1 nos.
160 A 4P 35kA MCCB, microprocessor based release having adjustable
O/L, SC protection - 1 nos.
100 A 4P 35kA MCCB, microprocessor based release having adjustable
Nos 1.00 220000.00 220000 1 220000 220000
O/L, SC protection - 2 nos.
Incomer
63A, TPN, switch disconnector unit (Isolator), AC23, 415V, 50Hz,
complete with handle assembly having door interlock - 1 no.
Busbar
1 Set of 100 A TPN busbars of high conductivity electrolytic quality
Aluminium alloy.
Instruments
2A, C curve SP MCB - 3 nos.
RYB indication lamp, LED type - 3 nos.
1 No 3 phase Digital Multi function meter to read V, A, F Acc class 1.
Incomer
200A FP 35kA MCCB with microprocessor based release with
adjustable OL, SC and EF protection - 1 nos.
Busbar
1 Set of 250 A TPN busbars of high conductivity electrolytic quality
Aluminium alloy.
Instruments
2A, C curve SP MCB - 3 nos.
RYB indication lamp, LED type - 3 nos.
1 No 3 phase Digital Multi function meter to read V, A, F Acc class 1.
24 Supply and Fixing of All in One solar system with aesthetically design
luminaire & 6-8 MTR Solar Pole. 6000Lm Solar Light with Efficacy-
135lm/w. Battery capacity 100Ah LiFePo4, Life Cycle 2000 @ 90%
DOD with IP68 Dimension 120x146x470mm 12.2Kg, Life expectacy
above 50,000Hr , colour temperature 4000K, Standard Light Profile 6H
100% + 6H 50%, Working Temperature -10 to +60 degree, IP67 (Min)
CRI>70, Average Lighting beam angle 120degree, PV Module- Mono-
Si, 180Wp/23Voc Dimension 172x172x4000mm, Solar cell Efficiency
16.4%, 8 site String, Total Column Length 6Mtr,Aluminium housing
powder coated bottom Part 2Mtr, Solar PV Module 4Mtr, Remote
Monitoring, Run time Extension, Total Nominal Peak power O/P
360Wp, Luminaire Housing Pressure die cast aluminium with corrosion
Resistance Polyester powder coated, Impact Resistance >IK07, Lamp nos 86.00 187058.00 16086988 86 187058 16086988
starting time should be not more than 10Seconds. Thermal managment
system should be provided and LED must be mounting on neat sink
condutive aluminium with suitable large are surface be means of fins to
dissipate the heat to ambient air. Applications standard Fixture should
confirm to applicable IEC 60598-1 IEC 61000-3-2, IEC 61547, Test
compliance for LED is LM 80 (IS-16105) and Test comliance at the time
of delivery, Howerer the tenderer shall submit all technical test report as
technical bid for the same at the time of submission of bid, internal
wiring fiber glass insulated multi stand wire. Protection overvoltage.
0.00 0 0 0
25 Supply and Fixing 3000 Amp TPN Sandwich alumininum bus bar
trunking complete shutable for
IP 54 protection with top end cover plate of 1.6mm thik G.I. Sheet with meter 80.00 35500.00 2840000 80 35500 2840000
sutaible arrangement for fixing
etc complete in all respect.
0 0
RISING MAIN
Supply and Fixing 400 Amp TPN Sandwich alumininum bus bar
trunking complete shutable for IP 54 protection with top end cover plate
1 of 1.6mm meter 50.00 17800.00 890000 50 17800 890000
thik G.I. Sheet with sutaible arrangement for fixing etc complete in all
respect.
Supply and erection of 100 Amp. TPN tap off box on rising mains
2 EACH 4.00 19990.00 79960 4 19990 79960
complete with HRC fuses etc. complete in all respect.
Supply and erection of incoming adopter box for mounting 100 Amp.
3 TPN CFS unit including connectors of required capacity on to the rising EACH 2.00 8780.00 17560 2 8780 17560
Mains complete in all respect.
Supply and Fixing of Flange End for 400 Amp sandwich Al bus bar
4 EACH 2.00 25750.00 51500 2 25750 51500
trunking complete in all respect.
LIFT
Digital car positions indicator in car and at all positions indicator in car
and at all floors with Up/DOWN direction, all signal fixtures in stainless
stell faceplates, light fixtures, ventilation fan, etc complete with all
accessories including automatic rescue device in the event of power
failure etc., Complete with necessary scaffolding, electrical panel, logic
control panel and shaft lighting etc required for the erection of the
elevators as required.
Machine Room Type (MR) Type with the traction motor placed in Lift
Topp (suitable as per cpwd specification, simplex full collective
operation with/without attendant. Car/Hoistway Entrance, protected by
stainless steel hairline doors and clear center /side opening min as per
a site. 13 Pasanger Lift, suitable car size Inside dimensions and entrance
at front side on all the serving floors, provided with matt finish stainless
steel panel on all four side and ceiling, stretcher protection on three
sides complete as per requirment.
Amount
S. No. Description of Item Unit TOTAL QTY Rate
UPSOR DSR 2018 NSR
1.2 Providing laying, testing & commissioning of 'C' class heavy duty MS
Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges,
tapers, nuts bolts, gaskets etc. in ground including welding, excavation &
providing cement concrete blocks as supports, anticorrosive treatment
with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of
following sizes complete as required.
1.3 Providing, laying, testing & commissioning of 'C' class heavy duty MS
pipe conforming to IS 3589/IS 1239 including Welding, fittings like
elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe
on the wall/ceiling with suitable clamp/support frame and painting with
two or more coats of synthetic enamel paint of required shade complete
as required :
1.4 Supplying and fixing single headed internal hydrant valve with
instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast
iron wheel ISI marked conforming to IS 5290 (Type -A) with blank
Gunmetal/Stainless Steel cap and chain as required :
1.4.1 Single headed Stainless steel Set 58 5987.00 347246.00 58.00 5987.00 347246
1.6 Supplying and fixing orifice plate made out of 6 mm thick stainless steel
(Grade 304) with orifice of required size to be fitted between flange &
landing valve of external and internal hydrants to reduce pressure at the 58 1291.00 74878.00 1291.00 74878
outlet to the level of 3.5 kg/cm2 complete as required.
Each 58.00
1.9.1 Stainless Steel (Grade 304) Set 116 4434.00 514344.00 116.00 4434.00 514344
1.10 Supplying and fixing first-aid Hose Reel with MS construction spray
painted in post office red, conforming to IS 884 complete with the
following as required.
20 mm nominal internal dia water hose thermoplastic (Textile
reinforced) type -2 as per IS: 12585
20 mm nominal internal dia gun metal globe valve & nozzle.
Drum and brackets for fixing the equipmets on wall.
Connections from riser with 25 mm dia stop gun metal valve & M.S.
Pipe and socket.
1.11 Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm
nominal internal diameter size nozzle conforming to IS 903 suitable for
nstantaneous connection to interconnect hose pipe coupling as required :
1.11.1 Stainless Steel (Grade 304) Set 58 1648.00 95584.00 58.00 1648.00 95584
1.12 Supplying and fixing of fire brigade connection of cast iron body with
gun metal male instantaneous inlet couplings complete with cap and
chain as reqd. for suitable dia MS pipe connection conforming to IS 904
as required :
1.12.1 2 way - 100 mm dia M.S. Pipe Set 7 6590.00 46130.00 7.00 6590.00 46130
1.13 Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS
sheet, 1200 mm in height with air release valve on top and flanged
connection to riser, drain arrangement with 25 mm dia gun metal wheel 21 18009.00 378189.00 18009.00 378189
valve with required accessories, pressure gauge and paintingwith
synthetic enamel paint of approved shade as required.
Set 21.00
1.14.1 150 mm width x 50mm depth x 1.6 mm thickness. Metre 80 531.00 42480.00 80.00 531.00 42480
1.15 Providing and fixing of Weather proof hose cabinets fabricated from 14 g
M.S. Sheet with full glass door and mortise locking arrangement ,
suitable to accommodate one Hydrant landing valve, 2 nos. 15 M long
hose and 1 No branch pipe. The cabinet shall be painted with one coat of
primer and finished stove enamelled "Fire Red", "Fire Hose" written on 19 6698.00 127262.00 6698.00 127262
front including suitably mounted on a raised masonry platform as
required. (Approx 0.75mx0.6 m x 0.25 m).
Each 19.00
1.17 Providing and fixing in position the industrial type pressure gauges with
58 1094.00 63452.00 1094.00 63452
gun metal / brass valves complete as required Each 58.00
1.18 Providing and fixing resilient rubber neoprene lined single arch
vibration eliminators with unit control suitable for raw water upto 450 C
temperature working pressure 25 kg and test pressure 37.5 kg/cm 2.
1.20.1 Capacity 4.5 Kg. Each 62 8033.00 498046.00 62.00 8033.00 498046
1.21.1 Capacity 22.5 kg. Each 2 20674.00 41348.00 2.00 20674.00 41348
1.22 Providing and fixing ABC Powder type fire extinguishers consisting of
welded M.S. cylinderical body, squeeze lever discharge valve fitted with
pressure indicating guage internal discharge tube 30 cms long high
pressure discharge hose, discharge nozzle, suspension bracket
conforming to IS:15683 finished externally with red enamel paint and
fixed to wall with brackets complete with internal charge. (Halon Free
Gas)
1.22.1 Capacity 6.0 Kg. Each 62 3636.00 225432.00 62.00 3636.00 225432
E EXTERNAL PLUMBING
1.0 External Water Supply System
1.1 Providing and fixing G.I. pipes complete with G.I. fittings including
trenching and refilling etc.
1.1.1 20 mm dia nominal bore Metre 60 283.80 17028.00 60 283.8 17028
1.1.2 25 mm dia nominal bore Metre 160 364.55 58328.00 160 364.55 58328
1.1.3 32 mm dia nominal bore Metre 160 424.70 67952.00 160 424.7 67952
1.1.4 40 mm dia nominal bore Metre 260 483.15 125619.00 260 483.15 125619
1.1.5 50 mm dia nominal bore Metre 310 565.25 175227.50 310 565.25 175227.5
1.1.6 65 mm dia nominal bore Metre 485 716.00 347260.00 485 716 347260
1.1.7 80 mm dia nominal bore Metre 935 866.40 810084.00 935 866.4 810084
1.2 Providing and fixing gun metal gate valve with C.I. wheel of approved
quality (screwed end) :
1.3.1 With common burnt clay F.P.S.(non modular) bricks of class designation
27 1582.45 42726.15 1582.45 42726.15
7.5 Each 27
1.4.1 With common burnt clay F.P.S.(non modular) bricks of class designation
22 9288.40 204344.80 9288.4 204344.8
7.5 Each 22
1.5 Painting G.I. pipes and fittings with two coats of anti-corrosive
bitumastic paint of approved quality :
1.5.1 20 mm dia nominal bore Metre 60 11.10 666.00 60.00 11.10 666
1.5.2 25 mm dia nominal bore Metre 160 14.15 2264.00 160.00 14.15 2264
1.5.3 32 mm dia nominal bore Metre 160 17.05 2728.00 160.00 17.05 2728
1.5.4 40 mm dia nominal bore Metre 260 19.40 5044.00 260.00 19.40 5044
1.5.5 50 mm dia nominal bore Metre 310 23.35 7238.50 310.00 23.35 7238.5
1.5.6 65 mm dia nominal bore Metre 485 28.95 14040.75 485.00 28.95 14040.75
1.5.7 80 mm dia nominal bore Metre 935 33.60 31416.00 935.00 33.60 31416
1.6 Providing and filling sand of grading zone V or coarser grade, allround
the G.I. pipes in external work :
1.6.1 20 mm dia nominal bore Metre 60 144.55 8673.00 60.00 144.55 8673
1.6.2 25 mm dia nominal bore Metre 160 148.40 23744.00 160.00 148.40 23744
1.6.3 32 mm dia nominal bore Metre 160 152.25 24360.00 160.00 152.25 24360
1.6.4 40 mm dia nominal bore Metre 260 154.15 40079.00 260.00 154.15 40079
1.6.5 50 mm dia nominal bore Metre 310 159.95 49584.50 310.00 159.95 49584.5
1.6.6 65 mm dia nominal bore Metre 485 252.45 122438.25 485.00 252.45 122438.25
1.6.7 80 mm dia nominal bore Metre 935 260.15 243240.25 935.00 260.15 243240.25
1.7 Providing and fixing C.I. double acting air valve of approved quality
with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers
etc if required will be paid separately) :
1.8.1 80 mm dia nominal bore Each 5 3135.52 15677.62 5.00 3135.52 15677.6224
1.9 Providing and fixing C.I. dirt box strainer for bulk type water meter with
nuts, bolts, rubber insertions etc. complete conforming to IS : 2373 :
1.9.1 80 mm dia nominal bore Each 5 3593.04 17965.19 5.00 3593.04 17965.1936
1.10 Providing and laying D.I. specials of class K-12 suitable for push-on
jointing as per IS : 9523 :
1.12 Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes
conforming to IS : 8329 :
1.12.1 100 mm dia Ductile Iron Class K-9 pipes Metre 210 1073.50 225435.00 210 1073.5 225435
2.1.1 All kinds of soil. Cum 1359 252.30 342875.70 1359 252.3 342875.7
2.2 Excavating trenches of required width for pipes, cables, etc including
excavation for sockets, and dressing of sides, ramming of bottoms, depth
upto 1.5 m, including getting out the excavated soil, and then returning
the soil as required, in layers not exceeding 20 cm in depth, including
consolidating each deposited layer by ramming, watering, etc. and
disposing of surplus excavated soil as directed, within a lead of 50 m :
2.2.1 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
Metre 3000 364.20 1092600.00 364.20 1092600
3000.00
2.2.2 Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm.
Metre 850 568.60 483310.00 568.60 483310
850.00
2.3 Extra for excavating trenches for pipes, cables etc. in all kinds of soil for
depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over
corresponding basic item for depth upto 1.5 metre).
2.3.1 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
750 462.53 346900.50 462.53 346900.5
Metre 750.00
2.3.2 Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm.
400 722.12 288848.80 722.12 288848.8
Metre 400.00
2.5 Extra for every additional lift of 1.5m or part thereof in:
2.5.1 All kinds of soil (Manhole) Cum 1019 90.40 92117.60 1019.00 90.40 92117.6
2.6 Providing and laying cement concrete Cement Concrete with 4 cm gauge
approved stone grit, coarse sand & cement in the proportion of 8:4:1
155 4470.00 692850.00 4470.00 692850
including supply of all materials, labour, Tools & plants etc. required for
proper completion of the work. Cum 155.00
2.7 Providing, laying and jointing glazed stoneware pipes class SP-1 with
stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine
sand) including testing of joints etc. complete :
2.7.1 150 mm diameter Metre 200 500.20 100040.00 200 500.2 100040
2.7.2 200 mm diameter Metre 1100 794.25 873675.00 1100 794.25 873675
2.7.3 250 mm diameter Metre 600 1173.70 704220.00 600 1173.7 704220
2.8 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand :
10 graded stone aggregate 40mm nominal size) all round S.W. pipes
including bed concrete as per standard design.
2.8.1 150 mm diameter Metre 200 999.15 199830.00 200 999.15 199830
2.8.2 200 mm diameter Metre 1100 1164.80 1281280.00 1100 1164.8 1281280
2.8.3 250 mm diameter Metre 600 1346.95 808170.00 600 1346.95 808170
2.9 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand :
10 graded stone aggregate 40mm nominal size) up to haunches of
S.W/RCC pipes including bed concrete as per standard design.
2.9.1 250 mm diameter Metre 750 861.15 645862.50 750.00 861.15 645862.5
2.9.2 300 mm diameter Metre 350 993.65 347777.50 350.00 993.65 347777.5
2.10 Providing and fixing square-mouth S.W. gully trap class SP-1 complete
with C.I. grating brick masonry chamber with water tight C.I. cover with
frame of 300 x300 mm size (inside) the weight of cover to be not less
than 4.50 kg and frame to be not less than 2.70 kg as per standard design
:
2.10.1 180x150 mm size P type with sewer bricks Each 75 2413.65 181023.75 75 2413.65 181023.75
2.11 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes
with collars jointed with stiff mixture of cement mortar in the proportion
of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :
2.11.1 250 mm dia. R.C.C. pipe Metre 750 754.45 565837.50 750.00 754.45 565837.5
2.11.2 300 mm dia. R.C.C. pipe Metre 350 863.65 302277.50 350.00 863.65 302277.5
2.11.3 450 mm dia. R.C.C. pipe Metre 400 1392.70 557080.00 400.00 1392.70 557080
2.11.4 500 mm dia. R.C.C. pipe Metre 200 1656.95 331390.00 200.00 1656.95 331390
2.11.5 600 mm dia. R.C.C. pipe Metre 250 1948.35 487087.50 250.00 1948.35 487087.5
2.12 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4
coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5
coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size),
foundation concrete 1:4:8 mix (1 cement : 4 coarse
sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside
plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse
sand) finished with floating coat of neat cement and making making
channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size) finished with a floating coat of neat
cement complete as per standard design :
2.12.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame
(light duty) 455x610 mm internal dimensions, total weight of cover and
frame to be not less than 38 kg (weight of cover 23 kg and weight of
frame 15 kg) :
2.12.1.1 With Sewer bricks conforming IS : 4885 Each 85 10915.65 927830.25 85 10915.65 927830.25
2.14 Constructing brick masonary circular type manhole 0.91m internal dia at
bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse
sand) in side cement plaster 12 mm thick with cement mortar 1:3 (1
cement : 3 coarse sand) finished with a floating coat of neat cement,
foundation concrete 1 :3:6 mix (1 cement : 3 coarse sand : 6 graded
40mm nominal size), and making necessary channel in cement concrete
1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm
nominal size) finished with a floating coat of neat cement all complete as
per standard design:
2.14.1 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade
designation) 560mm internal diameter confirming to I.S. 12592, total
weight of cover and frame to be not less than 182 kg., fixed in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20
mm nominal size) including centering shuttering all complete.
(Excavation, foot rests and 12 mm thick cement plaster at the external
surface shall be paid for separately) :
2.14.1.1 With common burnt clay F.P.S. (non modular) bricks of class
45 11038.10 496714.50 11038.10 496714.5
designation 7.5 Each 45.00
2.14.1.2 With Sewer bricks conforming IS : 4885 Each 25 11033.75 275843.75 25.00 11033.75 275843.75
2.15 Extra depth for circular type manhole 0.91m internal dia (at bottom) with
beyond 0.91m to 1.67m.
2.15.1 With common burnt clay F.P.S. (non modular) bricks of class
17 6448.40 109622.80 6448.40 109622.8
designation 7.5 Metre 17.00
2.15.1.2 With Sewer bricks conforming IS : 4885 Metre 10 6474.15 64741.50 10.00 6474.15 64741.5
2.16.1 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade
designation) 560mm internal diameter conforming to I.S. 12592, total
weight of cover and frame to be not less than 182kg. fixed in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate
20mm nominal size) including centering, shuttering all complete.
(Excavation, foot rests and 12 mm thick cement plaster at the external
surface shall be paid for separately) :
2.16.1.1 With common burnt clay F.P.S. (non modular) bricks of class
30 21235.65 637069.50 21235.65 637069.5
designation 7.5 Each 30.00
2.16.1.2 With Sewer bricks conforming IS : 4885 Each 30 21254.90 637647.00 30.00 21254.90 637647
2.17 Extra depth for circular type manhole 1.22m internal dia (at bottom)
beyond 1.68 m to 2.29 m :
2.17.1 With common burnt clay F.P.S. (non modular) bricks of class
9 8368.40 75315.60 8368.40 75315.6
designation 7.5 Metre 9.00
2.17.2 With Sewer bricks conforming IS : 4885 Metre 9 8402.00 75618.00 9.00 8402.00 75618
2.18.1 2.30 m deep with SFRC Cover and frame (heavy duty HD-20 grade
designation) 560mm internal diameter conforming to I.S. 12592, total
weight of cover and frame to be not less than 182kg. fixed in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate
20mm nominal size) including centering, shuttering all complete.
(Excavation, foot rests and 12 mm thick cement plaster at the external
surface shall be paid for separately) :
2.18.1.1 With common burnt clay F.P.S. (non modular) bricks of class
0 45459.15 0.00 45459.15 0
designation 7.5 Each 0.00
2.18.1.2 With Sewer bricks conforming IS : 4885 Each 20 45531.90 910638.00 20.00 45531.90 910638
2.19 Extra depth for circular type manhole 1.52m internal dia (at bottom)
beyond 2.30m :
2.19.1 With common burnt clay F.P.S. (non modular) bricks of class
0 19514.30 0.00 19514.30 0
designation 7.5 Metre 0.00
2.19.2 With Sewer bricks conforming IS : 4885 Metre 7 19601.35 137209.45 7.00 19601.35 137209.45
2.20 Providing orange colour safety foot rest of minimum 6 mm thick plastic
encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS :
1786 having minimum cross section as 23 mmx25mm and over all
minimum length 263 mm and width as 165mm with minimum 112 mm
space between protruded legs having 2 mm tread on top surface by
ribbing or chequering besides necessary and adequate anchoring
projections on tail length on 138 mm as per standard drawing and 1095 463.05 507039.75 463.05 507039.75
suitable to with stand the bend test and chemical resistance test as per
specifications and having manufacture's permanent identification mark to
be visible even after fixing, including fixing in manholes with 30x20x15
cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) complete as per design.
Each 1095.00
2.21.1 With common burnt clay F.P.S. (non modular) bricks of class
150 5209.10 781365.00 5209.10 781365
designation 7.5 Each 150.00
2.22.1.1 With common burnt clay F.P.S. (non modular) bricks of class
15 3979.10 59686.50 3979.10 59686.5
designation 7.5 Metre 15.00
3.3 Extra for every additional lift of 1.5 m or part thereof in.
3.3.1 All kinds of soil. Cum 900 90.40 81360.00 900.00 90.40 81360
3.4 Providing and laying cement concrete with 4 cm gauge approved stone
grit, coarse sand & cement in the proportion of 8:4:1 including supply of
24 4470.00 107280.00 4470.00 107280
all materials, labour, Tools & plants etc. required for proper completion
of the work. Cum 24.00
3.6 Centring and shuttering including stutting, propping etc. and removal of
form for:
3.6.1 Suspended floors, roofs, landings, balconies and acees platform Sqm 90 693.05 62374.50 90.00 693.05 62374.5
3.8 M-150 Brick Work in 1:6 cement and Coarse sand mortar (One cement
& six fine sand of 1.25 F.M.) mortar in foundation and plinth including
109 3750.00 408750.00 3750.00 408750
supply of all materials labour, Tools & plants etc. required for proper
completion of the work. Cum 109.00
3.9 Providing orange colour safety foot rest of minimum 6 mm thick plastic
encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS :
1786 having minimum cross section as 23 mmx25mm and over all
minimum length 263 mm and width as 165mm with minimum 112 mm
space between protruded legs having 2 mm tread on top surface by
ribbing or chequering besides necessary and adequate anchoring
projections on tail length on 138 mm as per standard drawing and
suitable to with stand the bend test and chemical resistance test as per 252 463.05 116688.60 463.05 116688.6
specifications and having manufacture's permanent identification mark to
be visible even after fixing, including fixing in manholes with 30x20x15
cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) complete as per design.
Each 252.00
3.10 Providing and fixing in position precast RCC manhole cover and frame
of required shape and approved quality.
3.10.1 HD-20 circular shape 560 mm internal diameter. Each 24 1471.50 35316.00 24.00 1471.50 35316
3.11 Boring/drilling bore well of required dia for casing/ strainer pipe, by
suitable method prescribed in IS: 2800 (part I), including collecting
samples from different strata, preparing and submitting strata chart/bore
log, including hire & running charges of all equipments, tools, plants &
machineries required for the job, all complete as per direction of
Engineer –in-charge, upto 90 metre depth below ground level.
3.12.1 200 mm nominal size dia. Metre 30 1066.05 31981.50 30.00 1066.05 31981.5
3.13 Supplying, assembling, lowering and fixing in vertical position in bore
well unplasticized PVC medium well screen (RMS) pipes with ribs,
conforming to IS: 12818, including hire & labour charges, fittings &
accessories etc. all complete, for all depths, as per direction of Engineer-
in-charge.
3.13.1 200 mm nominal size dia. Metre 330 1135.80 374814.00 330.00 1135.80 374814
3.14 Supplying, filling, spreading & levelling stone boulders of size range 5
cm to 20 cm, in recharge pit, in the required thickness, for all leads & 39 1326.55 51735.45 1326.55 51735.45
lifts, all complete as per direction of Engineer-in-charge. Cum 39.00
3.16 Supplying, filling, spreading & levelling coarse sand of size range 1.5
mm to 2 mm in recharge pit, in required thickness over gravel layer, for
39 1326.55 51735.45 1326.55 51735.45
all leads & lifts, all complete as per direction of Engineer –in-charge.
Cum 39.00
3.18 Development of tube well in accordance with IS : 2800 (part I) and IS:
11189, to establish maximum rate of usable water yield without sand
content (beyond permissible limit), with required capacity air
compressor, running the compressor for required time till well is fully
developed, measuring yield of well by "V" notch method or any other
approved method, measuring static level & draw down etc. by step draw 120 857.60 102912.00 857.60 102912
down method, collecting water samples & getting tested in approved
laboratory, i/c disinfection of tubewell, all complete, including hire &
labour charges of air compressor, tools & accessories etc., all as per
requirement and direction of Engineer-in-charge.
Hours 120.00
3.19 Providing and fixing suitable size threaded mild steel cap or spot welded
plate to the top of bore well housing/ casing pipe, removable as per
requirement, all complete for borewell of:
3.20 Providing and fixing M.S. clamp of required dia to the top of casing/
housing pipe of tubewell as per IS: 2800 (part I), including necessary
bolts & nuts of required size complete.
4.1.1
Filter Feed Pump (Domestic Water) in Water Supply Pump Room
Set of Two Pumps (1 Working + 1 Standby)
Capacity 3.0 LPS
Head 30 M.
HP 2.0 HP Approx. Set 1 179684.00 179684.00 1.00 179684.00 179684
including stainless steel grade 316 pipe suction and delivery headers and
isolation/ control valves( ball valves/butterfly valves/ Non return valves/
vibration eliminators etc as required) , power box, equipped with fuses/
isolators/circuit breakers as required.
4.5.1 Chlorination of Domestic Water Each 1 28236.00 28236.00 1.00 28236.00 28236
All switchboards shall have provision for entry of cables from the top or
bottom as required.
All live accessible parts shall be shrouded and all equipment shall be
finger touch proof. The busbars insulation shall be with heat shrinkable
sleeves. SMC/DMC shrouds and busbar supports shall be used.
Padlocking facility shall be provided on all outgoing feeders doors and
switch handles shall be lockable in OFF position.
4.6.1 Electric Panel For Water Supply Pumps at Water Supply Pump
Room
INCOMING
1 No. 150 amps TP + NL MCCB with the following accessories:
1 No. square flush mounting 0-500 volts scaled voltmeter with three way
and OFF switch.
Three phase indicating lights.
Electrolytic high conductivity three phase and neutral tinned alluminium
bus bar rated at 200 amps having a current density of 1 amp per Sqmm
suitable to with stand symmetrical fault level of 25 MVA at 415 volts.
The neutral bus bar is to be of 100% capacity.
OUTGOING UNITS
4.8 Providing, laying, testing & commissioning of 'B' class heavy duty G.I.
pipe conforming to IS 1239 including welding, fittings like elbows, tees,
flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the
wall/ceiling with suitable clamp/support frame and painting with two or
more coats of synthetic enamel paint of required shade complete as
required :
45.11 Providing and fixing resilient rubber neoprene lined style arch vibration
eliminators suitable for raw water upto 45 deg.C. Temperature
working pressure upto 25 Kg/Sqcm.
4.12 Providing and fixing heavy duty armoured cables 1.1 KVA grade
including necessary support clamps at ceiling level and connection lugs
complete in all respects.
4.12.1 Power cable Copper 3 core 10 sq.mm Metre 35 302.00 10570.00 35.00 302.00 10570
4.12.2 Power cable 3 core 6 sqmm Metre 50 188.00 9400.00 50.00 188.00 9400
4.12.3 Power cable Copper 3 core 4 sq.mm Metre 50 137.00 6850.00 50.00 137.00 6850
4.12.4 Control cable copper 2 core 1.5 sq.mm Metre 128 62.00 7936.00 128.00 62.00 7936
Supply and installation of MS Class 'C' with hot dip galvanized puddle
flange 25 to 150 mm dia. in accordance to relevant IS pipe standards as
required to be provided (in the structural slab & wall) of various
diameter. Puddle flanges shall be provided for all the structural
component of the STP/ETP. Lot-1
Supply and fixing of mechanical punched hole fine screen for 2-3 mm
size complete as required MOC- SS 304. Set-1
Supply and fixing of electronic type level indicator and controller for
automatic operation of the system with high/low level alarm complete
with auxillary NO/NC contacts for each tank. Lot-1
Supply and fixing of sight tube (of 3.5 to 4.5 m length) with isolation
valve at top/bottom, demarcation on tube & for making the installation
complete. Lot-1
Supply and fixing Disc type, EPDM membrane based, non clog type air
dispersion system capable of handling 3-5 cfm of air with oxygen
transfer efficiency of 3-4% per/meter water depth. Air dispersion grid
shall be assembled in modular form so that they can be replaced /
repaired easily from plat form at the top. (Imported fine bubble
membrane diffusers for equalisation tank, aeration tank & sludge holding
tank) Lot-1
Supply and fixing Tube type, silicon membrane based, non clog type air
dispersion system capable of handling 3-5 cfm of air with oxygen
transfer efficiency of 3-4% per/meter water depth. Air dispersion grid
shall be assembled in modular form so that they can be replaced /
repaired easily from plat form at the top. (Imported fine bubble
membrane diffusers for MBR tank) Lot-1
Providing & fixing butterfly valve tested to a pressure not less than 15
Kg/Sq.cm. 50 to 150 mm dia as required Including rubber gasket, 2 nos.
table-E flanges, nuts, bolts, washers & painting complete as required.Lot-
1
Providing & fixing dual plate CI wafer type check valve 50 to 150 mm
dia. as required tested to a pressure of 10 Kg/sqcm. Including rubber
gasket, 2 nos. table-E flanges, union, nuts, bolts, washers & painting
complete as required. Lot-1
Providing and fixing forged brass ball valve with SS ball suitable for
test pressure of not less than 15 kg / sq.cm of the 25 to 40 mm dia. Lot-
1:
Supply and fixing of horizontal, centrifugal Sludge disposal pump for the
disposal of sludge from tube settler to sludge holding tank. The pumps
shall have CI casing, CI/bronze Impeller & SS 304 shaft & sleeve with
mechanical rotary shaft seal connected by a flexible tier type coupling to
TEFC induction motor suitable for 415+10% Volts, 3 Phase, 50Hz, AC
Power Supply mounted on a common channel base-plate with coupling
guard, 150 mm dia pressure gauge with GM isolation cock, suitable
vibration eliminator pads under foundation of approved design, dry
running protection including all necessary piping, valves, level controller
complete with probs and other accessories complete as required. Set-1
2 Nos. Electro-magnetic flow meter cum totalizer at the sewage inlet and
outlet of membrane suction pump of suitable size.
1 Set Diffrential pressure switch transmittor and for pressure alarm high
and low, flow switch for flow alarm high and low.
1 Set Online rotameter for checking the air flow to the MBR module.
1 Set Air Rotameter for Biological Air supply and Air scouring
All live accessible parts shall be shrouded and all equipment shall be
finger touch proof. The busbars insulation shall be with heat shrinkable
sleeves. SMC/DMC shrouds and busbar supports shall be used.
Padlocking facility shall be provided on all outgoing feeders doors and
switch handles shall be locakble in OFF position.
INCOMING
1 No. 250 Amp 25 kA TPN MCCB with Thermal over load and magnetic
short circuit release site settable
INDICATING PANEL
BUSBAR
OUTGOING UNITS
2 Nos 63 Amp. TPN MCCB of breaking capacity 10KA (For 7.5 KW Air
Blowers for EQT, AT & SHT)
2 Nos. fully automatic DOL starters with push buttons and ON/OFF
indicating lights and overload relays for 7.5 KW Air Blower .
10 Nos 25 Amp. TPN MCB of breaking capacity 10KA (For 2 Kw, Eq.
transfer, MBR suction, sludge feed, MBR permeate, MBR backwash
pumps)
10 Nos. fully automatic DOL starters with push buttons and ON/OFF
indicating lights and overload relays for 2.0 KW pump .
10 Nos. selector switch for selecting mode of operation i.e.
auto/manual/off.
10 Nos. single phase preventors.
10 Nos. square flush mounting 0-30 amps scaled ammeters with three
way and OFF selector switch.
Space for 5 nos Level Controllers.
2 Nos 16 Amp. TPN MCB of breaking capacity 10KA (For 0.5 Kw,
Hydro dosing solution pump and citric solution dosing pump)
2 Nos. fully automatic DOL starters with push buttons and ON/OFF
indicating lights and overload relays for 0.5 KW pump .
2 Nos. selector switch for selecting mode of operation i.e.
auto/manual/off.
2 Nos. single phase preventors.
2 Nos. square flush mounting 0-30 amps scaled ammeters with three way
and OFF selector switch.
Supplying & laying of following 1100 volt grade XLPE insulated PVC
sheathed copper conductor armoured cables required size & length as
per specification in existing trenches, cable trays, ducts, clamped to wall
with suitable clamps including providing and fixing of all fixing
accessories, connecting, testing and commissioning. 1 Lot
6.2.1 Electrical Work as Descrive Above Set 1 282361.00 282361 1 282361 282361
G STP CIVIL
Earth work in surface excavation not exceeding 30 cm in depth but
exceeding 1.5 m in width as well as 10 sqm on plan including getting out
and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed
by Engineer-in- Charge:
All kinds of soil 100Sq
8.07 92.55 746.94 8.07 92.55 746.943285
m
Earth work in excavation by mechanical means (Hydraulic excavator) /
manual means in foundation trenches or drains (not exceeding 1.5 m in
width or 10 sqm on plan), including dressing of sides and ramming of
bottoms, lift upto 1.5 m, including getting out the excavated soil and
disposal of surplus excavated soil as directed, within a lead of 50 m.
All kinds of soil Cum 4035.35 252.30 1018118.81 4035.35 252.3 1018118.805
Filling available excavated earth (excluding rock) in trenches, plinth,
sides of foundations etc. in layers not exceeding 20cm in depth,
Cum 1383.32 219.65 303845.69 1383.32 219.65 303845.6889
consolidating each deposited layer by ramming and watering, lead up to
50 m and lift upto 1.5 m.
Supplying chemical emulsion in sealed containers including delivery as
specified.Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 161.41 200.85 32420.00 161.41 200.85 32420.0019
All work upto plinth level Cum 1144.77 8398.65 9614512.48 1144.77 8398.65 9614512.482
All work from plinth level upto floor V level Cum 1.56 9802.20 15315.94 1.56 9802.2 15315.9375
Total
Brick work
Providing and laying autoclaved aerated cement blocks masonry with
150mm/230mm/300 mm thick AAC blocks in super structure above
plinth level up to floor V level with RCC band at sill level and lintel level
with approved block laying polymer modified adhesive mortar all Cum 9.66 6636.95 64112.94 9.66 6636.95 64112.937
complete as per direction of Engineer-in-Charge. (The payment of RCC
band and reinforcement shall be made for seperately).
Total
WOOD AND P. V. C. WORK
Providing and fixing flush door shutters conforming to IS : 2202 (Part-I)
non-decorative type.core of block board construction with frame of 1st
class tiard wood and well mathched commercial 3 ply veneering wiih
vertical grains or cross bands and face veneers on both faces of shutters.
30mm thick including ISI marked Stainless Steel butt hinges with
Sqm 2.10 1819.80 3821.58 2.10 1819.8 3821.58
necessary screws
Providing and fixing aluminium extruded section body tubular type
universal hydraulic door closer (having brand logo with ISI, IS : 3564,
embossed on the body, door weight upto 36 kg to 80 kg and door width Each 1.00 851.60 851.60 1.00 851.6 851.6
from 701 mm to 1000 mm), with double speed adjustment with
necessary accessories and screws etc. complete.
Providing and fixing factory made s›ngIe extruded WPC (Wood Pol
ymer Composite) solid door/window/Ceasetory window & other
Frame/Chowkhat comprising of virgin PVC polymer of K value 58-60 (
Suspension Grade), calcium carbonate and natural fibers (wood powder/
rice husk/whent husk) and non toxic additives (maximum oxicily index
of 12 for 100 gms) fabricated wilh miter joints after applying PVC
solvent cement and screwed wilh full body threaded star headed SS
screws having minimum frame density of 750 kg/ cum screw withdraw
strength Of 2200 N (Face) & 1100 N (Edge), minimum compressive
strength of 58N/mm2. modules of elasticity 900 N/mm2 and resistance
to spread of flame of Class A category with properly of being termite/
borer proof, water/moisture proof and fire retardant and fixed in position
with M. S. hold fast/lugs/SS dash fasteners of required dia and length
complete as per direction of Engineer-in-Chargo (M. S hold fast/lugs Or
SS dash fasteners shall be paid for separately).
Nole: For WPC solid door/window frames. minces. 5mm tolerance in
dimension i.e. depth and width of profile shall be acceptabe Variation in
profile dimensions on plus side be acceptable but no extra payment on
this account shall be made.
Frame size 65 x 125mm Rmt 5.20 1091.00 5673.20 59.00 1091 64369
Providing and fixing aluminium tower bolts anodised (anodic coating not
less than grade AC 10 as per IS:1868) transparent or dyed to required
colour or shade with necessary screws etc. complete:
Twin rubber stopper Each 1.00 62.05 62.05 1.00 62.05 62.05
Providing and fixing aluminium work for doors, windows, ventilators
and partitions with extruded built up standard tubular sections/
appropriate Z sections and other sections of approved make conforming
to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and
size, including necessary filling up the gaps at junctions, i.e. at top,
bottom and sides with required EPDM rubber/ neoprene gasket etc.
Aluminium sections shall be smooth, rust free, straight, mitred and
jointed mechanically wherever required including
cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass /
stainless steel screws, all complete as per architectural drawings and the
directions of Engineer-in-charge. (Glazing, paneling and dash fasteners
to be paid for separately) :
For fixed portion
With float glass panes of 5.00 mm thickness (weight not less then 12.50
Sqm 2.97 903.00 2681.91 2.97 903 2681.91
kg/sqm)
Total
Steel Work
Steel work welded in built up sections/framed worK including cutting
hoisting, rixing in position and applying a priming coat of approved steel
primer using structural steel, etc. as required.
In gratings, frames, guard bar, ladders, railings, brackts. gates & similar
Kg 1044.55 95.00 99232.25 1044.55 95 99232.25
works.
Supplying and fixing rolling shutters of approved make, made of
required size M.S. laths, interlocked together through their entire length
and jointed together at the end by end locks, mounted on specially
designed pipe shaft with brackets, side guides and arrangements for
inside and outside locking with push and pull operation complete,
including the cost of providing and fixing necessary 27.5 cm long wire
springs manufactured from high tensile steel wire of adequate strength
conforming to IS: 4454 - part 1 and M.S. top cover of required thickness
for rolling shutters.
80x1.25 mm M.S. laths with 1.25 mm thick top cover Sqm 0.00 2303.00 0.00 2303
Providing and fixing ball bearing for rolling shutters. Each 0.00 364.00 0.00 364
Extra for providing mechanical device chain and crank operation for
operating rolling shutters.
Exceeding 10.00 sqm and up to 16.80 sqm in the area Sqm 0.00 960.00 0.00 960
Extra for providing grilled rolling shutters manufactured out of 8 mm dia
M.S. bar instead of laths as per design approved by Engineer-in- charge, Sqm 0.00 871.00 0.00 871
(area of grill to be measured).
Total
FLOORING AND CLADDING WORK
Providing and fixing Ist quality ceramic glazed wall tiles conforming to
IS: 15622 (thickness to be specified by the manufacturer), of approved
make, in all colours, shades except burgundy, bottle green, black of any
size as approved by Engineer-in-Charge, in skirting, risers of steps and
dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sqm 1742.25 902.00 1571504.99 1742.25 902 1571504.99
sand) and jointing with grey cement slurry @ 3.3kg per sqm, including
pointing in white cement mixed with pigment of matching shade
complete.
Total
ROOF & FALSE CEILING WORK
Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse
sand : 4 stone aggregate 10 mm and down gauge), including finishing
with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :
In 75x75 mm deep chase MTR 103.46 237.25 24545.89 103.46 237.25 24545.885
Making khurras 45x45 cm with average minimum thickness of 5 cm
cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400
micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse Each 4.00 244.05 976.20 4.00 244.05 976.2
sand) and a coat of neat cement, rounding the edges and making and
finishing the outlet complete.
Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x
20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70
and initial emittance > 0.75 on waterproof and sloped surface of terrace,
laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4
coarse sand) and grouting the joints with mix of white cement & marble
powder in ratio of 1:1, including rubbing and polishing of the surface up Sqm 523.39 1374.10 719190.20 523.39 1374.1 719190.199
to 3 cuts complete, including providing skirting up to 150 mm height
along the parapet walls in the same
manner.
Total
FINISHING WORK
12 mm cement plaster of mix :
1:6 (1 cement: 6 sand) Sqm 298.84 150.00 44825.93 298.84 150 44825.925
15 mm cement plaster on rough side of single or half brick wall of mix :
1:6 (1 cement: 6 sand) Sqm 298.84 206.00 61560.94 298.84 206 61560.937
6 mm cement plaster of mix :
1:3 (1 cement: 3 sand) Sqm 606.89 134.00 81323.26 606.89 134 81323.26
Neat Cement Punning` sqm 371.24 40.00 14849.60 371.24 40 14849.6
Distempering with oil bound washable distemper of approved brand and
manufacture to give an even shade :
New work (two or more coats) over and including water thinnable
Sqm 570.32 153.45 87515.45 570.32 153.45 87515.45055
priming coat with cement primer
Finishing walls with Premium Acrylic Smooth exterior paint with
Silicone additives of required shade:
New work (Two or more coats applied @ 1.43 ltr/10 sqm over and
including priming coat of exterior primer applied @ 2.20 kg/10 sqm) Sqm 103.00 161.15 16598.45 103.00 161.15 16598.45
Using rough kota stone. sqm 645.01 1353.70 873150.04 645.01 1353.7 873150.037
Providing and laying integral cement based treatment for water proofing
on the vertical surface by fixing specified stone slab 22 mm to 25 mm
thick with cement slurry mixed with water proofing compound
conforming to IS:2645 in recommended proportions with a gap of 20 mm
(minimum) between stone slabs and the receiving surfaces and filling the
gaps with neat cement slurry mixed with water proofing compound and
finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3
coarse sand) 20 mm thick with neat cement punning mixed with water
proofing compound in recommended proportion complete at all levels
and as directed by Engineer-in-charge :
Using rough Kota stone sqm 509.15 1738.00 884909.65 509.15 1738 884909.652
Providing and laying integral cement based water proofing treatment
including preparation of surface as required for treatment of roofs,
balconies, terraces etc consisting of following operations:
(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement
admixed with water proofing compound conforming to IS. 2645 and
approved by Engineer-in-charge over the RCC slab including adjoining
walls up to 300 mm height including cleaning the surface before
treatment.
(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm
to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse
sand) admixed with water proofing compound conforming to IS : 2645
and approved by Engineer-in-charge over 20 mm thick layer of cement
mortar of mix 1:5 (1 cement :5 coarse sand) admixed
(e) The whole terrace so finished shall be flooded with water for a
minimum period of two weeks for curing and for final test. All above
operations to be done in order and as directed and specified by the
Engineer-in-Charge :
With average thickness of 120 mm and minimum thickness at khurra as
Sqm 523.39 1178.00 616553.42 523.39 1178 616553.42
65 mm.
30605010.28 30605010.28
-4300003.945 -4300003.945
26305006.34 26305006.34
-263050.0634 -263050.0634
AMOUNT OF STP CIVIL (G) 26041956.28 26041956.28 0.00
H UG TANK
B METAL FILLING
4 300mm thick crushed stone CUM. 44.85 1986.18 89080.17 44.85 1986.18 89080.173
C PCC WORK
D RCC WORK
6 Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using cement content as per approved
design mix, manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work, including pumping of R.M.C.
from transit mixer to site of laying , excluding the cost of centering,
shuttering finishing and reinforcement, including cost of admixtures in
recommended proportions as per IS : 9103 to accelerate/ retard setting of
concrete, improve workability without impairing strength and durability
as per direction of the Engineer - in - charge.
(Note :- Cement content considered in this item is @ 330 kg/cum.
Excess/ less cement used as per design mix is payable/recoverable
separately).
All works upto plinth level CUM. 54.05 8398.65 453980.63 54.054 8398.65 453980.6271
Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using cement content as per approved
design mix, manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work, including pumping of R.M.C.
from transit mixer to site of laying , excluding the cost of centering,
7 shuttering finishing and reinforcement, including cost of admixtures in
recommended proportions as per IS : 9103 to accelerate/ retard setting of
concrete, improve workability without impairing strength and durability
as per direction of the Engineer - in - charge.
(Note :- Cement content considered in this item is @ 330 kg/cum.
Excess/ less cement used as per design mix is payable/recoverable
separately).
All works above plinth level upto floor V level CUM. 118.08 9802.20 1157443.78 118.08 9802.2 1157443.776
TOTAL
E SHUTTERING WORK
TOTAL
G 230 MM BRICKWORK
Brick work with common burnt clay F.P.S. (non modular) bricks of class
10 designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1
cement : 6 coarse sand)
CUM. 7.56 6157.65 46577.33 7.56414 6157.65 46577.32667
TOTAL
H PLASTER WORK
13 WATER PROOFING
Providing and laying water proofing treatment in sunken portion of WCs,
bathroom etc., by applying cement slurry mixed with water proofing
cement compound consisting of applying :
I OHT
Earth work in exacavation in trenches for foundations in ordinary
soil(loan clay or sand) including lift upto 1.5 m and dressing of sides and
1. CUM 176.63 90.00 15896.25 90.00 15896.25
ramming of bottom sand disposal of surplus excavated earth as directed
by the Engineer i/c with in alead of 50m. 176.63
Providing and laying Cement concrete 1:4:8 (1cement :4 C. sand :8
graded stone ballast 40 mm. nominal size) including supply of all
2. materials, labour and T&P etc. required for proper completion of the CUM 16.39 4470.00 73266.88 4470.00 73266.88
work and curing complete, also including cost of formwork in
foundation. 16.39
Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using cement content as per approved
design mix, manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work, including pumping of R.M.C.
3 from transit mixer to site of laying , excluding the cost of centering, CUM 5.40 8594.65 46411.12 8594.65 46411.12
shuttering finishing and reinforcement, including cost of admixtures in
recommended proportions as per IS : 9103 to accelerate/ retard setting of
concrete, improve workability without impairing strength and durability
as per direction of the Engineer-in-charge.
5.40
Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using cement content as per approved
design mix, manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work, including pumping of R.M.C.
4 from transit mixer to site of laying , excluding the cost of centering, CUM 59.23 8594.65 509060.92 8594.65 509060.92
shuttering finishing and reinforcement, including cost of admixtures in
recommended proportions as per IS : 9103 to accelerate/ retard setting of
concrete, improve workability without impairing strength and durability
as per direction of the Engineer-in-charge.
59.23
0.00 0.00
Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using cement content as per approved
design mix, manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work, including pumping of R.M.C.
5 from transit mixer to site of laying , excluding the cost of centering, CUM 33.30 8594.65 286199.32 8594.65 286199.32
shuttering finishing and reinforcement, including cost of admixtures in
recommended proportions as per IS : 9103 to accelerate/ retard setting of
concrete, improve workability without impairing strength and durability
as per direction of the Engineer-in-charge.
33.30
Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using cement content as per approved
design mix, manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work, including pumping of R.M.C.
6 from transit mixer to site of laying , excluding the cost of centering, CUM 38.53 7364.01 283718.99 7364.01 283718.99
shuttering finishing and reinforcement, including cost of admixtures in
recommended proportions as per IS : 9103 to accelerate/ retard setting of
concrete, improve workability without impairing strength and durability
as per direction of the Engineer-in-charge.
38.53
Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using cement content as per approved
design mix, manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work, including pumping of R.M.C.
7 from transit mixer to site of laying , excluding the cost of centering, 0.00 0.00
shuttering finishing and reinforcement, including cost of admixtures in
recommended proportions as per IS : 9103 to accelerate/ retard setting of
concrete, improve workability without impairing strength and durability
as per direction of the Engineer-in-charge.
A All works upto plinth level CUM 0.83 7364.01 6104.47 0.83 7364.01 6104.47
0.00 0.00
Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using cement content as per approved
design mix, manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work, including pumping of R.M.C.
B from transit mixer to site of laying , excluding the cost of centering, CUM 13.56 8594.65 116584.73 8594.65 116584.73
shuttering finishing and reinforcement, including cost of admixtures in
recommended proportions as per IS : 9103 to accelerate/ retard setting of
concrete, improve workability without impairing strength and durability
as per direction of the Engineer-in-charge.
13.56
0.00 0.00
T.M.T.-FE-500 steel or iron in plain work such as reinforced concrete or
reinforced, brick work (when not included in over all rates ) wrought to
8 required shape as necessary including bending for proper completion of QTL 283.52 7321.35 2075770.21 7321.35 2075770.21
the work and including supply of all steel and wastage & over lapping &
hooks. 283.52
11 Stairs, (excluding landings) except spiral-staircases SQM 36.00 545.68 36.00 545.68
12 Arches, domes, vaults up to 6 m span SQM 346.43 1502.15 520385.24 346.43 1502.15 520385.24
13 Lintels, beams, plinth beams, girders, bressumers and SQM 135.50 484.04 65588.82 135.50 484.04 65588.82
cantilevers
14 Foundations, footings, bases of columns, etc. for mass concrete SQM 9.20 249.76 2297.78 9.20 249.76 2297.78
15 Columns, Pillars, Piers, Abutments, Posts and Struts SQM 143.94 643.31 92597.12 143.94 643.31 92597.12
16 M-150 brick work in 1:4 cement and coarse sand of 2.25 coarseness
modulus mortar in super-structure. Above plinth level up to floor two
level (up to two storey) including necessary cutting and molding of brick 1.80 4300.00 7,740.00 4300.00 7740.00
work as required and also including honey combed brick work in
thickness of wall 12cms. Cu.M 1.80
17 15mm cement plaster in single coat on fair side of single or half brick
wall for exterior plastering up to floor two level including internal
rounded angles chamfers, and/or rounded angles not exceeding 80mm in Sq.M 300.92 181.25 54,540.84 181.25 54540.84
girth and finished even and smooth. (1) 1 cement : 6 coarse sand
(1.25FM) 300.92
19 Finishing wall with water proof cement paint of approved make and
quality on new work with two coats to give an even shade including
Sq.M 150.91 83.00 12,525.32 83.00 12525.32
supply of all materials , laour ,tools and pants etc. required for proper
completion of the work. 150.91
113.04
24
a. providing and fixing G.I.pipescomplete with
G.I. fitting and clamps including
cuttingand making good the walls.
40 mm dia nominal bore (inlet) R.M. 40.00 560.81 22432.27 40.00 560.81 22432.27
65 mm dia nominal bore (outlet) R.M. 25.00 627.79 15694.87 25.00 627.79 15694.87
40 mm dia nominal bore (wash out) R.M. 25.00 560.81 14020.17 25.00 560.81 14020.17
65 mm dia nominal bore (overflow) R.M. 30.00 627.79 18833.84 30.00 627.79 18833.84
b. 40 mm dia nominal bore pump room to OHT pipeline R.M. 250.00 560.81 140201.67 250.00 560.81 140201.67
65 mm dia nominal bore OHT to building line R.M. 214.00 627.79 134348.09 214.00 627.79 134348.09
J BOUNDARY WALL
1 Earth -work in exacavation in trenches for foundation and for pipes,
cable etc. in ordinary soil (Loan clay or sand) including lift upto 1.5 m
lead upto 50 m. and dressing of sides and ramming of bottoms and Cu.M 1602.24 90.00 1,44,202.03 1910.41 90.00 1,71,936.47
disposal of surplus excavated earth as directed by the Engineer. i/c
within a lead of 30 m. .
2 2.5cm thick Damp proof course with cement concrete consisting of 1 part
cement ,1.5 pats approved coarse sand and 3 parts approved 10 mm
graded stone grit and including water proofing material as orderd by the Sq.M 423.69 300.00 1,27,108.38 505.18 300.00 1,51,555.19
Engineer Incharge in the proportion as specified by the manufacture.
5.A All works upto plinth level CUM 439.47 8398.65 36,90,925.18 523.99 8398.65 44,00,802.45
5.B All works above plinth level upto floor V level CUM 221.55 9802.20 21,71,707.55 264.16 9802.20 25,89,393.03
0.00 0.00
6 T.M.T.-FE-500 steel or iron in plain work such as reinforced concrete or
reinforced, brick work (when not included in over all rates ) wrought to
required shape as necessary including bending for proper completion of QTL 616.56 7081.00 43,65,832.26 735.14 7081.00 52,05,514.71
the work and including supply of all steel and wastage & over lapping &
hooks.
0.00 0.00
7 M-150 brick work in 1:6 cement and coarse sand of 2.25 fineness
modulous mortar in foundation and plinth including supply of all
Cu.M 646.13 3900.00 25,19,923.59 770.41 3900.00 30,04,581.60
materials, labour and tools and plants etc. required for proper completion
of the work.
0.00 0.00
8 M-150 brick work in 1:6 cement and coarse sand mortar in super
structure including necessary cutting and moulding of bricks required
and also including honey comb brick work thickness of walls more than Cu.M 635.54 4330.00 27,51,896.38 757.78 4330.00 32,81,169.82
one brick and for extra labour to above items
0.00 0.00
9 Proving & injecting chamical emulsion for preconstructional anti-termite
treatment and creating a chemical barrier under & alround the column
pits wall trenches basement excavation top surface if plinth filling
junction of wall & floor along the external perimeter of building
expansion joints surrounding of pipes & coduits etc.complete plinth area
of the building at ground floor only shall be measured as per I.S.63/3( 0 0.00
part II 1981 ) Aldrine emlsifiable concentrate or any other approved
material such as Htrachlore or Chlordance will be used . The rate of
application of chemical emulsion shall be as follows:
(I) Treatment for masonary & foundation 5litres/ sqm. 0.00 0.00
(II) Back fill in immediate contract with foundation 7.5 litres / sqm. 0.00 0.00
(III) Treatment of top surface of plinth filling 5 litres/sqm . 0.00 0.00
(IV) Treatment of junction of wall and floor 7.5litres/sqm. 0.00 0.00
(V) Treatment of soil along external perimeter of building 7.50 0.00 0.00
litres/sqm.
(VI) Treatment of soil under Apron along external perimeter 5litres/sqm
Sq.M 1592.28 200.0 3,18,456.68 1898.53 200.0 3,79,705.59
0.00 0.00
10 12 mm cement plaster in single coat on rough side of single or half
brick wall for interior plastering up to floor two level including internal
Sq.M 3043.20 263.55 8,02,035.36 3628.50 263.55 9,56,291.18
rounded angles not exceeding 80 mm in girth and finshed even and
smooth. (1)1 cement : 6 coarse sand.
0.00 0.00
11 15mm cement plaster in single coat on fair side of single or half brick
wall for exterior plastering up to floor two level including internal
rounded angles chamfers, and/or rounded angles not exceeding 80mm in Sq.M 3043.20 303.90 9,24,828.48 3628.50 303.90 11,02,701.15
girth and finished even and smooth. (1) 1 cement : 6 coarse sand
(1.25FM)
0.00 0.00
12 Providing wall putty on old surface with approvel quality material of
Sq.M 6086.40 54.00 3,28,665.60 7257.00 54.00 3,91,878.00
Berger/J.K./Birla or similar make 2 coats
0.00 0.00
13 White washing one coat including supply of all materials , labour and T
& P etc required for proper completion of work. Sq.M 6086.40 22.00 1,33,900.80 7257.00 22.00 1,59,654.00
14 M.S or iron work of small sizes and section such as holding down bolts,
hold fast ,tie rods, grading etc, ( When not including in an overall rates )
wrought to required shape as necessary for bending etc including supply
of steel and its wastage including cost of bolts nuts if required and 0.00 0.00
welding ,grinding and making holes as required for proper completion of
works
Fabrication of M.S grill / MS hollow bar over boundary wall KG 36518.40 61.50 22,45,881.60 43542.00 61.50 26,77,833.00
15 Painting or vanishing two coats on iron works in small areas or new
wood work with one coat of ready mixed priming paint & one coat of Sq.M 1217.28 104.00 1,26,597.12 1451.40 104.00 1,50,945.60
approved superior quality ready mixed paint of clear synthetic varnish
including supply of all materials labour and T & P etc. required for
FORM WORK 0.00 0.00
16 Centering and shuttering including strutting, propping etc. and removal
of form for : 0.00 0.00
Foundations, footings, bases of columns, etc. for mass concrete 2958.80 284.85 8,42,814.73 3527.87 284.85 10,04,913.66
0.00 0.00
Lintels, beams, plinth beams, girders, bressumers and
921.08 552.05 5,08,479.56 1098.23 552.05 6,06,275.66
cantilevers
1,38,67,768.19 89,87,397.27
LESS GST 14.05 % 78,80,225.58 16534962.17 1,07,15,947.35
LESS 1% LABOUR CESS ON DSR( ON TOTAL AFTER
79,59,027.83 93,95,832.84
DEDUCTION 14.05%)
1,38,67,768.19 79,59,027.83 1,65,34,962.17 94,89,791.17
AMOUNT INCREASE DUE
TO ADDITIONAL
AMOUNT OF BOUNDARY WALL (J) 2,18,26,796.02 2,60,24,753.34 41,97,957.32 LENGTH OF BOUNDARY
WALL AFTER MERGER
OF DEGREE COLLEGE
K ENTRANCE GATE
1.
Excavation in foundation in ordinary soil (Loam,clay or sand) including
lift upto 1.50 M and lead upto 30 M.and including filling watering and
ramming of excavated earth into the trenches or into the space between 23.04 90.00 2073.22 23.0358 90 2073.222
the building and the sides of foundation trenches or into the plinth and
removal and disposal of surplus earth as directed by the Engineer-in-
charge upto a distance of 30 M from the foundation trenches. CUM
2 (a) Sand filling in plinth and under floor including supply of necessary
quantity of sand from a distance not exceeding 8 Kms. from the site of
work and including watering, dressing etc. labour and T&P etc.
required for proper complition of the work. saplings of girth upto 30
cms. measured at a height of 1 M. above ground level and removal of 16.13 380.00 6127.52 16.12506 380 6127.5228
rubbish upto a distance of 50 M. out side the periphery of area cleared.
including cost of sand.
CUM
4 Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using cement content as per approved
design mix, manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work, including pumping of R.M.C.
from transit mixer to site of laying , excluding the cost of centering,
shuttering finishing and reinforcement, including cost of admixtures in
recommended proportions as per IS : 9103 to accelerate/ retard setting of
concrete, improve workability without impairing strength and durability
as per direction of the Engineer-in-charge.
4A All works upto plinth level CUM 5.71 8398.65 47,930.76 5.70696 8398.65 47930.7596
4B All works above plinth level upto floor V level CUM 2.96 9802.20 29,011.08 2.95965 9802.2 29011.08123
in1:1.5:3having strength not less than M
150. (PWD- 289 ) CUM 2.56 9600.00 24537.60 2.556 9600 24537.6
7 Brick work with non modular fly ash bricks conforming to IS:12894,
class designation 10 average compressive strength in super structure
above plinth level up to floor V level in : Cement mortar 1:6 (1 cement :
6 coarse sand) 2.687 7280.70 19565.57072 2.68732 7280.7 19565.57072
CUM
8 Brick work with non modular fly ash bricks conforming to IS:12894,
class designation 10 average compressive strength in super structure
above plinth level up to floor V level in : Cement mortar 1:6 (1 cement :
6 coarse sand) 0.215 7280.70 1567.389096 0.21528 7280.7 1567.389096
CUM
10 Finishing walls with acrylic smooth extarior paint with silicon addtives
of required shed. Two or more coat applied @1.43 ltr/10sqm. Over and
4.14 164.70 681.86 4.14 164.7 681.858
including base coat of water proofing cement paint applied @ 2.20kg/10
sqm. SQM
11 Wall lining butch work upto 10m height with Dholpur stone 40 mm thick
rough facing on the exposed surface with stone strips of minimum length
300 mm and required width, including embedding every tenth layer and
bottom most layer in masonry or concrete after making necessary chases
of size 75x75 mm and by providing layer of 75 mm thick strips i/c 12 0.00 2388.00 0.00 0 2388 0
mm thick bed of cement mortar 1:3 (1 Cement : 3 coarse sand) i/c ruled
pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an
admixture of pigment to match the shade of stone complete as per
direction of Engineer-in-charge. SQM
14 Same as in item 502 above but in heavy sizes such as trusses, built up
gates, record racks, roof work, Gates etc. including rivetting or welding 270.00 61.50 16605.00 270 61.5 16605
where necessary. KG
15 Painting Ist coat over priming coat (but excluding cost of priming coat)
on steel and other metal surfaces up to 10 cm. width or girth or
small articles not exceeding 0.10sqm in area white superior synthetic
enamel such as LUXOL3,Hi-gloss apcolite superlac, DULUX
specified brushing to give an even shade and including cleaning the 4.50 104.00 468.00 4.5 104 468
surface of all dirt,dust and other foreign matter sand papering and
stoping including cost of all materials, labour tools and plants etc.
required for proper completion of the work.
SQM
-13875.31 -13875.31054
84881.35 84881.34811
121670.81 121670.8139
N.TOTAL 206552.16 N.TOTAL 206552.162
G TOTAL 206552.16 G TOTAL 206552.162
AMOUNT OF ENTRANCE GATE (K) FOR 2 NOS 413104.324 FOR 2 NOS 413104.324 0
L CC ROAD
Earth work in exacavation in trenches for foundations in ordinary soil(loan clay or
sand) including lift upto 1.5 m and dressing of sides and ramming of bottom sand
1 disposal of surplus excavated earth as directed by the Engineer i/c with in alead CUM 7501.33 90 675119.7 7501.33 90 675119.7
of 50m.(PWD-251)
2 CARTED OF EART FILLING CUM 13891.36 318.1 4418840.821 13891.36 318.1 4418840.821
M-150 Brick Work in 1:4 (One cement & four Corse sand)
4 mortar.foundation and plinth including supply of all materials labour, CUM 3195.01 4300 13738543 3195.01 4300 13738543
Tools & plants etc. required for proper completion of the work 305-B
Providing and laying in position bitumen hot sealing compound for expansion joints
6 etc. (DSR- 16.46.1)
RM 9260.91 2.91 26949.25 9260.91 2.91 26949.25
Using grade 'A' sealing compound.
M PATHWAY
Earth work in exacavation in trenches for foundations in ordinary soil(loan clay or
sand) including lift upto 1.5 m and dressing of sides and ramming of bottom sand
1 disposal of surplus excavated earth as directed by the Engineer i/c with in alead CUM 2805.71 90 252513.9 2805.71 90 252513.9
of 50m.(PWD-251)
Cement Concrete with proportions of 8:4:1 stone Ballast, Coarse sand and
2 cement.including supply of all materials, labour, Tools & plants etc. required for CUM 1870.47 4470 8361000.9 1870.47 4470 8361000.9
proper completion of the work.
M-150 Brick Work in 1:4 (One cement & four Corse sand)
3 mortar.foundation and plinth including supply of all materials labour, CUM 898.87 4300 3865141 898.87 4300 3865141
Tools & plants etc. required for proper completion of the work
(a) Sand filling in plinth and under floor including supply of necessary quantity of
sand from a distance not exceeding 8 Kms. from the site of work and including
watering, dressing etc. labour and T&P etc. required for proper complition of the
work. saplings of girth upto 30 cms. measured at a height of 1 M. above ground
4 level and removal of rubbish upto a distance of 50 M. out side the periphery of CUM 779.36 380 296156.8 779.36 380 296156.8
area cleared. including cost of sand.
Supply of 80mm thick ISI marked confirming to IS: 15658-2006 I shaped mechanically
compressed interloking cement concerete paver blocks, smooth high gloss finish, skid
resistant; manufactured from rubber moulds through vibro-compression mechanism. high
pressure and control vibration machine having plan dimension 200 x (160+120mm) with
5 minimum 5mm thick topping of O.P. cement mixed with 25% marble powder. The SQM 7793.64 726.6 5662858.824 7793.64 726.6 5662858.824
Compressive strength of concerete paver block shall not be less than 40 MPa and weight
4.50 kg per No. confirming to IS: 15658-2006 including cost of material, labour, T & P
(ii ) Color
O TUBEWELL
TUBEWELL 1 2192486 2192486 1 2192486 2192486
TOTAL 30283656.29
PERCENTAGE BELOW AT WHICH CONTRACTOR HAS
2431777.60
QUOTED FROM THE TENDERED AMOUNT @8.03%
TOTAL AMOUNT OF VARIATION 'B' 27851878.69
278.52 LACS
AMOUNT INCREASED
DUE TO MERGER OF
G. TOTAL (A+B) AS ADMIN & LIBRARY
BLOCK, INCREASE IN
G. TOTAL AS PER DPR 800603532.06 PER REVISED DPR + 839516955.97 38913423.92 BOUNDARY WALL
VARIATION LENGTH, ADDITIONAL
LIFTS & FAÇADE WORK