Professional Documents
Culture Documents
Y-900User Manual
Y-900User Manual
MW R
Y-900/Y-910
call button
(transmitter) Y-A1-WR Ф60x17
Cancel button
(transmitter) Y-A1-BC Ф60X17
Call button
Y-A3 Ф60x17
11. Data Maintenace :
(transmitter) Back-up data, Restore data ,Erase data.
Call button
(transmitter) Y-SC/433 85x85x17
Remote
Y-T17A 170 x 65 x 25
Control
Software function:
* Edit the message to rolling display on the receiver via “Input data setting”.
* Edit the user’s information for this software, such as name, sex, duty and so on for
management.
* Save all the transmitters in the receiver, with transmitter number setting, transmitter
address setting, ring tone choice and etc.
1 14
A. Transmitter Address-------from “0000” to “9999” *Data backup: copying data from one receiver to the other receiver.
B. Transmitter Number ( Transmitter inner address) -------change “FFFFFF” to inner *Record all the calling information: call number, call time, end time, service type, service
address of each transmitter (Get it via FUN1-4 function in receiver) person and etc.
C. Alarm output ------- There is an alarm light output. If you choose “Alarm output”,when
this transmitter calls, the Alarm corridor light will flash.It’s better to use this function for (2) Sketch:
emergency situation.
Y-900 Receiver Sketch:
D. Alert sound ------sound choice (12kinds,from “1” to “12”)
E. Pager group, pager address --------1 pager can belong to different pager group and 1 pager
group can have many different pagers)
F. Calling information ------ Transmitter’s number ⑨
when finish all the above setting, please press “Set”key.
Transmitter Sketch:
② ② ② ②
① ③ ③
① ①
Key Code Setting (It also can be set via FUN1-2 in receiver)
Edit the Text for pager. After setting,pager will show the number and text directly. ④
For example,if the transmitter’s number is “A001”.After setting the “Text” to be “Call”,the Y-A1-WR Y-A1-BC Y-A3 series Y-SC
pager will show “A001-CALL” when call via this transmitter.
Note: ① call ② indicator ③cancel ④ bill
Remote control Sketch:
Key note:
Location key
Switch the address of remote controller directly
and quickly.
Scheduling key Switch to the scheduling model directly and quickly. 1 2 3
4 5 6
Function key Click here to enter the menu after menu button 7 8 9
Ⅲ System setting
Power on, you could find Wireless calling system on the display .This message can be
edited via the software
Note: Before system setting, please set remote control firstly (Refer to FUN2-1setting)
13 2
Main function instruction
FUN1 Save /delete transmitter number
FUN2 Set remote control
FUN3 Display mode & rolling number setting
FUN4 Time settings
FUN5 Ring tone setting
FUN6 Receiver address settings
FUN7 Service type indicator and others
FUN8 Copy function
FUN9 Restore factory settings
3 12
C.Port setting: The symbol: ?,!,…,※ ,⊙,§ etc
Choose the COM port. It’s the most important step. If the COM port is not chosen correctly,
the software will not read the receiver. 6. When the calling number is correct , press the confirm key.
Note: We will offer a USB-CAN conventor. Insert it to PC and find the “Driver”,which we 7. Press the “call” button on the transmitter for 3 seconds until the receiver shows: setting
will attach in the CD with goods. success
After installation, please choose the correct COM port to work.
If setting failure and the display will show :setting
failure
8. To save another transmitter, please back to “F1-1” to set as above.
When all the transmitters are saved ,please press function key to back to the standby state.
Note:
* As for the cancel transmitter, it will be the same setting with call transmitter as above
(used same number ).
* If saving transmitter via software, please remember the address of transmitter.
Go to F1-1, input the address number and confirm it .
The calling number will display on the screen, then press the “call” button on the transmitter
for 3 seconds until the receiver shows: setting
success
If setting failure and the display will show : setting
failure
4. Layout: Delete transmitter:
A: Edit Floor Plan: Click the right mouse key to add “a new floor plan” and then re-name
Go to F1-1,input the saved transmitter address and confirm it.
it.This is used for service area management.
The receiver will show as follows:
F1-1 XXXX
XXXXXXX B
Press the confirm key and the transmitter number will be shown on the screen.
Press setting key to clear this number with showing : cleared
Success
Fun1-2 NONE
Fun 1-3 Check the status of saved transmitter(transmitter address and transmitter number)
F3-2 Rolling numbers (The number will be rolling displayed) ------default setting:00
1. Under FUN3-2, showing “F3-2 XX”
2. Input the number from 1 to 16 at “XX” place and confirm it
Note: 00 & 01 means no rolling.
F3-3 Rolling display time(Time gap between rolling numbers) ---default setting :20
1. Under FUN3-3,showing “F3-3 XX”
2. Input the number from 1 to 99 at “XX” place and confirm it
Note: F3-3 is based on F3-2, or it’s useless.
B. System setting:
F3-4 Display time ---default setting :60
Setting the format of this software and the sounds of warning.
1. Under FUN3-4,showing “F3-4 XX”
2. Input the number from 0 to 99 at “XX” place and confirm it
Note: “0” means the calling information is always shown on the receiver until the call is
canceled by “Cancel” button.
3. Press setting key to exit the setting state
Fun4 Time settings (current time, alarm output time & delay time)
5 10
2. Press the digit key on the remote control to select the time
Networking sketch Note:The terminal switch of the receiver must be turned on.
3. Press confirm key the receiver will show setting and back to FUN4-1
success
4. Press function key to exit the setting state
Converter
FUN4-2 Alarm output time -----default setting:10s
1. Under FUN4-2, press the confirm key and the receiver will show “F4-2 XX”
2. Input the time from 1-99s,which is the time for alarm light to keep flashing.
3. Press confirm key the receiver will show setting and back to FUN4-2
success
4. Press function key to exit the setting state
9 6
1. Under FUN5-1 , press number key “3”, showing “F5-3 XX”
2. Press left key or right key to select the repeated ring tones (0-5) FUN9 Restore factory setting
0 =keep ringing
1= repeat once
FUN9-1 deletes all the transmitter number
2= repeat twice 1. Under FUN9 , press confirm key , showing FUN9-1
3= repeat three times 2. Press confirm key and the receiver shows delete transmitter
4= repeat four times 3. Press setting key and it shows cleared which mean all the transmitter
5= repeat five times numbers have been deleted
3. press confirm key and the receiver shows setting 4. Receiver will go back to FUN9-1 automatically and press function key to exit setting state
success
Note:Default setting: 1 FUN9-2 Delete all remote control
1. Under FUN9-2 , press confirm key, showing delete remote control
2. Press setting key and it shows clearance which mean all the remoter controller have been deleted
FUN6 Receiver address setting successful
3. After that it will go back to the FUN9-2 and press function key to exit the setting state
FUN6-1 Set local address
FUN9-3 Delete all the call information
1. Under FUN6-1, press confirm key , showing “F6-1 XX” 1. Under FUN9-3,press confirm key and showing delete calling
2. Input the relative number to set the local address information
3. Press confirm key and receiver shows setting and exit the setting status 3. Press setting key and receiver shows clearance
successful
success
4. After that it will be back to FUN-9-3 automatically and press function key to exit the
FUN7 Service type symbols and others setting state
7 8