Professional Documents
Culture Documents
SORENSEN DCS600 1.7E Datasheet
SORENSEN DCS600 1.7E Datasheet
Test Equipment Solutions Ltd specialise in the second user sale, rental and distribution of
quality test & measurement (T&M) equipment. We stock all major equipment types such as
spectrum analyzers, signal generators, oscilloscopes, power meters, logic analysers etc from
all the major suppliers such as Agilent, Tektronix, Anritsu and Rohde & Schwarz.
We are focused at the professional end of the marketplace, primarily working with customers
for whom high performance, quality and service are key, whilst realising the cost savings that
second user equipment offers. As such, we fully test & refurbish equipment in our in-house,
traceable Lab. Items are supplied with manuals, accessories and typically a full no-quibble 2
year warranty. Our staff have extensive backgrounds in T&M, totalling over 150 years of
combined experience, which enables us to deliver industry-leading service and support. We
endeavour to be customer focused in every way right down to the detail, such as offering free
delivery on sales, covering the cost of warranty returns BOTH ways (plus supplying a loan
unit, if available) and supplying a free business tool with every order.
As well as the headline benefit of cost saving, second user offers shorter lead times, higher
reliability and multivendor solutions. Rental, of course, is ideal for shorter term needs and
offers fast delivery, flexibility, try-before-you-buy, zero capital expenditure, lower risk and off
balance sheet accounting. Both second user and rental improve the key business measure of
Return On Capital Employed.
We are based near Heathrow Airport in the UK from where we supply test equipment
worldwide. Our facility incorporates Sales, Support, Admin, Logistics and our own in-house
Lab.
- No-quibble parts & labour warranty (we provide transport for UK mainland addresses).
- Free loan equipment during warranty repair, if available.
- Full electrical, mechanical and safety refurbishment in our in-house Lab.
- Certificate of Conformance (calibration available on request).
- Manuals and accessories required for normal operation.
- Free insured delivery to your UK mainland address (sales).
- Support from our team of seasoned Test & Measurement engineers.
- ISO9001 quality assurance.
Email: info@TestEquipmentHQ.com
Web: www.TestEquipmentHQ.com
elg0430.qxd 2/22/01 9:55 PM Page 19
DCS 1 kW and 3 kW
DC Programmable
Switching Supplies
he DCS Family of 1 kW and 3 kW
T programmable power supplies
incorporate current mode switching
rates up to 100 kHz in high power
density, low profile chassis. Utilizing
unique packaging techniques, the
DCS Family provides continuous full
output power (1 kW or 3 kW) in any
volt/amp combination within the rated constant-voltage/current mode Options include an internal IEEE-488/
output voltage and current limits. operation. RS 232 interface, isolated analog
programming of voltage or current, and
This family has 10-turn potentiometers The DCS 3 kW Models have push the multichannel slave interface
to adjust voltage and current settings button control of the output standby (Option M85).
that are displayed simultaneously. mode, OVP reset, remote/local
LEDs indicate overtemperature, programming and preview status of
remote programming, shutdown and voltage, current and OVP setpoints.
overvoltage protection, status and
Features
♦ Output Voltage
Voltage ranges from 0-8 VDC to ♦ Remote Programming ♦ Software
0-600 VDC; current levels from • Selectable remote programming LabVIEW® driver for M9C/M85 can
1.7A to 350A for voltage, current and OVP be downloaded at no cost at
• Optional internal IEEE-488/RS 232 www.sorensen.com/support/
♦ Power Density Interface Card with voltage and downloads.cfm
• 1 kW of power in a 19 lb. package current readback and adjustable
only 1.75 inches high OVP (Option M9C) ♦ Regulatory Compliance
• 3 kW of power in a 33 lb. package • Optional isolated analog CE Mark, UL 1012, FCC Part 15
only 3.5 inches high programming (Option M51) Class A and CSA 22.2 #220 (1 kW)
• Optional multichannel slave
♦ Input Voltage interface (Option M85) ♦ 5 Year Warranty
• 1 kW: 100-132 VAC, single phase,
or 200-250 VAC, single phase ♦ Regulation
47-63 Hz (other inputs available) • Line regulation: 0.1%
• 3 kW: 190-250 VAC, three phase • Load regulation: 0.1%
or 200-250 VAC, single phase
47-63 Hz (2.5 kW max with single
phase input; other inputs available)
Sorensen • 858/450-0085 • 800/525-2024 • Fax: 858/458-0267 • 9250 Brown Deer Road • San Diego • California • 92121-2294 • www.sorensen.com • E-mail: sales@sorensen.com 19
elg0430.qxd 2/22/01 9:55 PM Page 20
Voltage: 0.1% Max. Voltage Differential from Output M9C*: Internal IEEE-488/RS 232 Interface
to Safety Ground M13: Locking shafts (front panel
Current: 0.1%
1 kW: 150 VDC potentiometers)
Transient Response: Typically recovers in
<1 ms to 1% of steady-state output voltage 3 kW: 150 VDC M32: Master/slave cable configured for two
(within 1% of Vmax) for 70-100% or or more units
Remote Start/Stop and Interlock: TTL
100-70% load change. 500 µs typical compatible input or 12-250 VAC M33: Replace input connector with terminal
Stability: ±0.05% of maximum voltage or (12-130 VDC) or a contact closure block (3 kW only)
current over 8 hours after 30 minute warm- Cooling: Internal fan, overtemperature M51: Isolated analog programming control
up time at fixed line, load and temperature shutdown at internal heat sink temperature of either the output current or voltage using
Efficiency: See table of 90°C analog signals that can be biased up to 60V
relative to the supply’s return line
Temperature Coefficient: 0.02%/°C of Remote Sense: The maximum allowed
maximum output voltage; 0.03%/°C of sense line drop is 1V (0.5V on the M85*: Multichannel slave interface
maximum output current DCS 8-125E model) * See digital programming discussion on page 49.
Remote Programming: External jumper via
rear panel connector J3
Overvoltage Protection: Crowbar type
adjustable from 5-110% of rated output
using front panel control (local or remote
program selectable via J3 jumper)
20 Sorensen • 858/450-0085 • 800/525-2024 • Fax: 858/458-0267 • 9250 Brown Deer Road • San Diego • California • 92121-2294 • www.sorensen.com • E-mail: sales@sorensen.com
elg0430.qxd 2/22/01 9:55 PM Page 21
Programming Constants
Output Power Constant Voltage Mode*
Combined Voltage Voltage Mode
Temp. Coeff.
Regulation Transient Drift
Model Current Line and Voltage
Voltage Ripple Noise Response % Vmax
ADC %/°C (Typ) Ohms/V V/V
VDC Load % (RMS)** (P-P) Time (Typ)
@ 50°C
µs (Typ)
DCS 8-125E 0-8 0-125 0.2 10 mV 100 mV 500 0.02 0.05 6.25
DCS 8-350 0-8 0-350 0.2 15 mV 100 mV 1000 0.02 0.05 625
DCS 12-250 0-12 0-250 0.2 10 mV 100 mV 1000 0.02 0.05 416.7
DCS 20-50E 0-20 0-50 0.2 10 mV 100 mV 500 0.02 0.05 250
DCS 20-150 0-20 0-150 0.2 10 mV 100 mV 1000 0.02 0.05 250
DCS 33-33E 0-33 0-33 0.2 10 mV 100 mV 500 0.02 0.05 151.5
DCS 40-25E 0-40 0-25 0.2 10 mV 100 mV 500 0.02 0.05 125
DCS 40-75 0-40 0-75 0.2 20 mV 100 mV 1000 0.02 0.05 125 0-10V =
0-100% V0
DCS 50-20E 0-50 0-20 0.2 20 mV 100 mV 500 0.02 0.05 100
or
DCS 55-55 0-55 0-55 0.2 20 mV 100 mV 1000 0.02 0.05 90.9
0-5V =
DCS 60-18E 0-60 0.18 0.2 20 mV 100 mV 500 0.02 0.05 83 0-100% V0
DCS 60-50 0-60 0-50 0.2 20 mV 100 mV 1000 0.02 0.05 83
DCS 80-13E 0-80 0-13 0.2 20 mV 100 mV 500 0.02 0.05 62.5
DCS 80-37 0-80 0-37 0.2 20 mV 100 mV 1000 0.02 0.05 62.5
DCS 150-7E 0-150 0.7 0.2 30 mV 200 mV 500 0.02 0.05 33.3
DCS 150-20 0-150 0-20 0.2 30 mV 200 mV 1000 0.02 0.05 33.3
DCS 300-3.5E 0-300 0-3.5 0.2 40 mV 200 mV 500 0.02 0.05 16.67
DCS 600-1.7E 0-600 0-1.7 0.2 100 mV 500 mV 500 0.02 0.05 8.33
Programming
Constant Current Mode* Temp. Current Constants, Current Input Current, A Nominal
Coeff. Drift Mode Efficiency %
Model Case
Regulation Ripple %/°C %I0 Max. (Typ.)
(Typ.) (Typ.) Ohms/A 230V Single 208V Three
Line and Load (RMS)** V/A
Phase Phase
% Combined mA
DCS 8-125E 0.2 160 0.03 0.05 40 8.5 N/A 82 I
DCS 8-350 0.2 870 0.03 0.05 14.3 24 13 82 II
DCS 12-250 0.2 400 0.03 0.05 20 26 14 82 II
DCS 20-50E 0.2 25 0.03 0.05 100 8.5 N/A 82 I
DCS 20-150 0.2 100 0.03 0.05 33.3 26 14 82 II
DCS 33-33E 0.2 10 0.03 0.05 151.5 8.5 N/A 82 I
DCS 40-25E 0.2 7 0.03 0.05 200 8.5 N/A 82 I
DCS 40-75 0.2 75 0.03 0.05 66.7 0-10V= 26 14 86 II
0-100% I0
DCS 50-20E 0.2 7 0.03 0.05 250 8.5 N/A 86 I
or
DCS 55-55 0.2 40 0.03 0.05 90.9 0-5V= 26 14 82 II
DCS 60-18E 0.2 6 0.03 0.05 277.8 0-100% I0 8.5 N/A 86 I
DCS 60-50 0.2 33 0.03 0.05 100 26 14 86 II
DCS 80-13E 0.2 4 0.03 0.05 384.6 8.5 N/A 82 I
DCS 80-37 0.2 20 0.03 0.05 135 26 14 86 II
DCS 150-7E 0.2 2 0.03 0.05 714.3 8.5 N/A 82 I
DCS 150-20 0.2 10 0.03 0.05 250 26 14 86 II
DCS 300-3.5E 0.2 1 0.03 0.05 1428.6 8.5 N/A 82 I
DCS 600-1.7E 0.2 1 0.03 0.05 2941 8.5 N/A 82 I
* Typical resolution is 0.02% ** RMS ripple typical from 20 Hz to 300 kHz
Sorensen • 858/450-0085 • 800/525-2024 • Fax: 858/458-0267 • 9250 Brown Deer Road • San Diego • California • 92121-2294 • www.sorensen.com • E-mail: sales@sorensen.com 21
elg0430.qxd 2/22/01 9:55 PM Page 22
Case I Case II
1.10 1.10
(28) (28)
17.52 17.52
(445) (445)
22 Sorensen • 858/450-0085 • 800/525-2024 • Fax: 858/458-0267 • 9250 Brown Deer Road • San Diego • California • 92121-2294 • www.sorensen.com • E-mail: sales@sorensen.com